summaryrefslogtreecommitdiff
path: root/drivers/net/qlge
AgeCommit message (Collapse)Author
2009-07-03qlge: Fix sizeof usage.Ron Mercer
Some usage was only sizing a pointer rather than the data type. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Add/use function for link up/down.Ron Mercer
We need to set/clear the mac address register when the link goes up/down respectively. Without this both ports of a 2-port device can end up with the same mac address in a bonding scenario. The new ql_link_on() and ql_link_off() will also be used in handling certain firmware events. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix MAC address bonding issue.Ron Mercer
This addes functionality to set/clear the MAC address in the hardware when the link goes up/down. The MAC address register is persistent across function resets. In bonding the same address can bounce from one port to the other. This can cause packets to be delivered to the wrong port. This patch clears the MAC address in the hardware when the link is down and sets it when the link comes up. It was found that pulling/pushing the cable from one port to another causes the same MAC address to be in both ports. The next patch in this series will use this functionality as well. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix tx byte counter.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix redundant call to free resources.Ron Mercer
The caller will free acquired resouces if a failure occurs. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Fix carrier on condition.Ron Mercer
We were turning on the carrier without verifying the link was up. This adds link up to the link initialize check before turning carrier on. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Clear frame to queue routing before reset.Ron Mercer
Not clearing the routing bits can cause frames to erroneously get routed to management processor. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-07-03qlge: Expand coverage of hw lock for config register.Ron Mercer
The hardware semaphore covers the configuration register as well as the ICB registers. The ICB high and low regs contain the address of the initialization control block and the config register is used to signal the hardware that a block is ready to be downloaded. Currently we were only protecting the ICB regs. This changes expands to cover the config register as well. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-15Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: Documentation/feature-removal-schedule.txt drivers/scsi/fcoe/fcoe.c net/core/drop_monitor.c net/core/net-traces.c
2009-06-12trivial: fix ETIMEOUT -> ETIMEDOUT typosJean Delvare
fix ETIMEOUT -> ETIMEDOUT typos Signed-off-by: Jean Delvare <khali@linux-fr.org> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-12trivial: fix typos s/paramter/parameter/ and s/excute/execute/ in ↵Martin Olsson
documentation and source comments. Signed-off-by: Martin Olsson <martin@minimum.se> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-06-11qlge: Allow RX buf rings to be > than 4096 bytes.Ron Mercer
RX buffer rings can be comprised of non-contiguous fixed size chunks of memory. The ring is given to the hardware as a pointer to a location that stores the location of the queue. If the queue is greater than 4096 bytes then the hardware gets a list of said pointers. This patch addes the necessary logic to generate the list if the queue size exceeds 4096. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-11qlge: Relax alignment on TX harware queue.Ron Mercer
The alignment was on size of queue boundary, but the hardware only requires 4-byte alignment. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: bugfix: Get rid of errant spin_unlock().Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add set TX csum ethtool op.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for varied pcie function numbers.Ron Mercer
Currently we support only PCIe NIC functions zero and one, and FCoE functions as 3 and 4. Future configurations can mix these up in any fashion. This patch removes the 0-1 dependancy and allows usage of any of the 4 functions. We also find the alternate NIC function (if exist) and determine our port number based on the comparison of the two functions: Lower function number gets first port, higher function gets second port. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for using alternate MAC address.Ron Mercer
Extract either manufacturer or Bladecenter Open Fabric Manager (BOFM) MAC address. BOFM may indicate an alternate MAC address. This patch honors that request by extracting the MAC address from a different flash location if a flag is set. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Drop inbound frames > MTU.Ron Mercer
The max frame size register is set higher than the MTU to accomodate FCoE frames. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Drop inbound error frames.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Remove netif_set_gso_max_size() call.Ron Mercer
Not necessary if hardware supports 65536 as it's the default setting. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-10qlge: Add support for retrieving firmware version.Ron Mercer
This is used by driver banner and ethtool info. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix timeout on firmware mailbox commands.Ron Mercer
Some firmware mailbox commands require the firmware to communicate with the FCoE driver running on another PCI function. This can potentially take several seconds. This wait is done in process context only. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix timeout on indexed register wait.Ron Mercer
There are 8 banks of 'sub-registers' each of which are accessed through address/data register pair. An example would be reading flash or the xgmac. Accessing these require the driver to wait for a ready bit before writing the address and then accessing the data. This patch increases the timeout to 100us to prevent timeouts that have been seen on some platforms. These register are accessed in process context only. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix bug in MTU setting process.Ron Mercer
Since an FCoE function shares a port with this NIC function, the jumbo settings must always be in place. This patch causes the hardware to be set up for jumbo if it is not already done. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix bug in firmware event handler.Ron Mercer
Each firmware mailbox command can have a different number of valid data elements. When waiting for a mailbox command to complete it the process passes it's element count and waits for the completion. It is possible that while waiting an unrelated firmware async event (AE) can arrive. When this happens, the handler will over write the element count with the value for the newly arrived AE. This can cause the mailbox command to not get all of it's data. This patch restores original mailbox count at the end of the handler. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-06-08qlge: Fix firmware event handler loop.Ron Mercer
Check status on every iteration of event handler loop and exit if an error occurred. If an error occurred then recover process will be queued so this loop should no continue. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-05-29net: dont update dev->trans_start in 10GB driversEric Dumazet
Followup of commits 9d21493b4beb8f918ba248032fefa393074a5e2b and 08baf561083bc27a953aa087dd8a664bb2b88e8e (net: tx scalability works : trans_start) (net: txq_trans_update() helper) Now that core network takes care of trans_start updates, dont do it in drivers themselves, if possible. Multi queue drivers can avoid one cache miss (on dev->trans_start) in their start_xmit() handler. Exceptions are NETIF_F_LLTX drivers (vxge & tehuti) Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-04-07dma-mapping: replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32)Yang Hongyang
Replace all DMA_32BIT_MASK macro with DMA_BIT_MASK(32) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-07dma-mapping: replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64)Yang Hongyang
Replace all DMA_64BIT_MASK macro with DMA_BIT_MASK(64) Signed-off-by: Yang Hongyang<yanghy@cn.fujitsu.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-04-02glge: remove unused #include <version.h>Huang Weiyi
Remove unused #include <version.h> in drivers/net/qlge/qlge_ethtool. Signed-off-by: Huang Weiyi <weiyi.huang@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-17Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/igb/igb_main.c drivers/net/qlge/qlge_main.c drivers/net/wireless/ath9k/ath9k.h drivers/net/wireless/ath9k/core.h drivers/net/wireless/ath9k/hw.c
2009-03-13qlge: bugfix: Pad outbound frames smaller than 60 bytes.Ron Mercer
With some asic configurations xmit of frames smaller than 60 bytes may fail. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13qlge: bugfix: Move netif_napi_del() to common call point.Ron Mercer
Moving netif_napi_del() up the call chain so it will get called from all exit points. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13qlge: bugfix: Tell hw to strip vlan header.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-13qlge: bugfix: Increase filter on inbound csum.Ron Mercer
Chip does not do UDP checksum when fragmentation occurs. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: bugfix: Fix endian issue related to rx buffers.Ron Mercer
This was introduced in an earlier net-next patch. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: bugfix: Pad outbound frames smaller than 60 bytes.Ron Mercer
With some asic configurations xmit of frames smaller than 60 bytes may fail. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: bugfix: Move netif_napi_del() to common call point.Ron Mercer
Moving netif_napi_del() up the call chain so it will get called from all exit points. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Remove spinlock from asic init path.Ron Mercer
There is nothing to contend with it. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Clear shadow registers before use.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Get rid of irqsave/restore in intr disable.Ron Mercer
The completion interrupt disable routine is only called from the ISR, so there is no need for irqsave/restore. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: bugfix: Tell hw to strip vlan header.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Add tx multiqueue support.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Add support for GRO.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Increase filtering for inbound csum settings.Ron Mercer
Chip does not do UDP checksum when fragmentation occurs. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Remove debug junk from asic reset logic.Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-10qlge: Move reset logic into asic_reset_worker func.Ron Mercer
Get rid of extraneous ql_cycle_adapter. It's only called from the one place. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-03qlge: Add support for lost firmware events.Ron Mercer
When the firmware is issuing events to the driver the events must be removed from the queue. If the queue overflows, the firmware will build and special event that captures those that are lost. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-03qlge: Save status from firmware crash (system err).Ron Mercer
Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2009-03-03qlge: Improve handling for firmware init failure.Ron Mercer
This event will arrive at boot time or after an MPI processor reset if the firmware failed to initialize. Signed-off-by: Ron Mercer <ron.mercer@qlogic.com> Signed-off-by: David S. Miller <davem@davemloft.net>