summaryrefslogtreecommitdiff
path: root/drivers/net/phy/nxp-tja11xx.c
AgeCommit message (Collapse)Author
2020-11-17net: phy: nxp-tja11xx: remove the use of .ack_interrupt()Ioana Ciornei
In preparation of removing the .ack_interrupt() callback, we must replace its occurrences (aka phy_clear_interrupt), from the 2 places where it is called from (phy_enable_interrupts and phy_disable_interrupts), with equivalent functionality. This means that clearing interrupts now becomes something that the PHY driver is responsible of doing, before enabling interrupts and after clearing them. Make this driver follow the new contract. Cc: Marek Vasut <marex@denx.de> Cc: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-17net: phy: nxp-tja11xx: implement generic .handle_interrupt() callbackIoana Ciornei
In an attempt to actually support shared IRQs in phylib, we now move the responsibility of triggering the phylib state machine or just returning IRQ_NONE, based on the IRQ status register, to the PHY driver. Having 3 different IRQ handling callbacks (.handle_interrupt(), .did_interrupt() and .ack_interrupt() ) is confusing so let the PHY driver implement directly an IRQ handler like any other device driver. Make this driver follow the new convention. Cc: Marek Vasut <marex@denx.de> Cc: Oleksij Rempel <o.rempel@pengutronix.de> Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-05-26net: ethtool: Add generic parts of cable test TDRAndrew Lunn
Add the generic parts of the code used to trigger a cable test and return raw TDR data. Any PHY driver which support this must implement the new driver op. Signed-off-by: Andrew Lunn <andrew@lunn.ch> v2 Update nxp-tja11xx for API change. Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-21net: phy: tja11xx: add SQI supportOleksij Rempel
This patch implements reading of the Signal Quality Index for better cable/link troubleshooting. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-15net: phy: tja11xx: execute cable test on link upOleksij Rempel
A typical 100Base-T1 link should be always connected. If the link is in a shot or open state, it is a failure. In most cases, we won't be able to automatically handle this issue, but we need to log it or notify user (if possible). With this patch, the cable will be tested on "ip l s dev .. up" attempt and send ethnl notification to the user space. This patch was tested with TJA1102 PHY and "ethtool --monitor" command. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-13net: phy: tja11xx: add cable-test supportOleksij Rempel
Add initial cable testing support. This PHY needs only 100usec for this test and it is recommended to run it before the link is up. For now, provide at least ethtool support, so it can be tested by more developers. This patch was tested with TJA1102 PHY with following results: - No cable, is detected as open - 1m cable, with no connected other end and detected as open - a 40m cable (out of spec, max lenght should be 15m) is detected as OK. Current patch do not provide polarity test support. This test would indicate not proper wire connection, where "+" wire of main phy is connected to the "-" wire of the link partner. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-06net: phy: tja11xx: add support for master-slave configurationOleksij Rempel
The TJA11xx PHYs have a vendor specific Master/Slave configuration bit, which is not compatible with IEEE 803.2-2018 spec for 100Base-T1 devices. So, provide a custom config_ange call back to solve this problem. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: tja11xx: add delayed registration of TJA1102 PHY1Oleksij Rempel
TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1 having no ID. On one hand it is possible to for PHY detection by compatible, on other hand we should be able to reset complete chip before PHY1 configured it, and we need to define dependencies for proper power management. We can solve it by defining PHY1 as child of PHY0: tja1102_phy0: ethernet-phy@4 { reg = <0x4>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>; reset-assert-us = <20>; reset-deassert-us = <2000>; tja1102_phy1: ethernet-phy@5 { reg = <0x5>; interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>; }; }; The PHY1 should be a subnode of PHY0 and registered only after PHY0 was completely reset and initialized. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: tja11xx: add initial TJA1102 supportOleksij Rempel
TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable. Both PHYs are similar but have different amount of functionality. For example PHY 1 has no PHY ID and no health monitor. Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-23net: phy: tja11xx: use phy_read_poll_timeout() to simplify the codeDejin Zheng
use phy_read_poll_timeout() to replace the poll codes for simplify tja11xx_check() function. Suggested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-29net: phy: tja11xx: Switch to HWMON_CHANNEL_INFO()Marek Vasut
The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood of errors, and makes the code easier to read. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: linux-hwmon@vger.kernel.org Reviewed-by: Guenter Roeck <linux@roeck-us.net> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-05-26net: phy: tja11xx: Add TJA11xx PHY driverMarek Vasut
Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special BroadRReach 100BaseT1 PHYs used in automotive. Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Guenter Roeck <linux@roeck-us.net> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Jean Delvare <jdelvare@suse.com> Cc: linux-hwmon@vger.kernel.org Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>