summaryrefslogtreecommitdiff
path: root/drivers/net/phy/mdio_bus.c
AgeCommit message (Collapse)Author
2021-02-03net: mdiobus: Prevent spike on MDIO bus reset signalMike Looijmans
The mdio_bus reset code first de-asserted the reset by allocating with GPIOD_OUT_LOW, then asserted and de-asserted again. In other words, if the reset signal defaulted to asserted, there'd be a short "spike" before the reset. Here is what happens depending on the pre-existing state of the reset signal: Reset (previously asserted): ~~~|_|~~~~|_______ Reset (previously deasserted): _____|~~~~|_______ ^ ^ ^ A B C At point A, the low going transition is because the reset line is requested using GPIOD_OUT_LOW. If the line is successfully requested, the first thing we do is set it high _without_ any delay. This is point B. So, a glitch occurs between A and B. We then fsleep() and finally set the GPIO low at point C. Requesting the line using GPIOD_OUT_HIGH eliminates the A and B transitions. Instead we get: Reset (previously asserted) : ~~~~~~~~~~|______ Reset (previously deasserted): ____|~~~~~|______ ^ ^ A C Where A and C are the points described above in the code. Point B has been eliminated. The issue was found when we pulled down the reset signal for the Marvell 88E1512P PHY (because it requires at least 50ms after POR with an active clock). Looking at the reset signal with a scope revealed a short spike, point B in the artwork above. Signed-off-by: Mike Looijmans <mike.looijmans@topic.nl> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210202143239.10714-1-mike.looijmans@topic.nl Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2021-01-07net: phy: replace mutex_is_locked with lockdep_assert_held in phylibHeiner Kallweit
Switch to lockdep_assert_held(_once), similar to what is being done in other subsystems. One advantage is that there's zero runtime overhead if lockdep support isn't enabled. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/ccc40b9d-8ee0-43a1-5009-2cc95ca79c85@gmail.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-20mdio_bus: suppress err message for reset gpio EPROBE_DEFERGrygorii Strashko
The mdio_bus may have dependencies from GPIO controller and so got deferred. Now it will print error message every time -EPROBE_DEFER is returned which from: __mdiobus_register() |-devm_gpiod_get_optional() without actually identifying error code. "mdio_bus 4a101000.mdio: mii_bus 4a101000.mdio couldn't get reset GPIO" Hence, suppress error message for devm_gpiod_get_optional() returning -EPROBE_DEFER case by using dev_err_probe(). Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com> Link: https://lore.kernel.org/r/20201119203446.20857-1-grygorii.strashko@ti.com Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-11-17net: phy: fix kernel-doc markupsMauro Carvalho Chehab
Some functions have different names between their prototypes and the kernel-doc markup. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org> Signed-off-by: Jakub Kicinski <kuba@kernel.org>
2020-09-29net: mdiobus: Remove WARN_ON_ONCE(in_interrupt())Sebastian Andrzej Siewior
in_interrupt() is ill defined and does not provide what the name suggests. The usage especially in driver code is deprecated and a tree wide effort to clean up and consolidate the (ab)usage of in_interrupt() and related checks is happening. In this case the check covers only parts of the contexts in which these functions cannot be called. It fails to detect preemption or interrupt disabled invocations. As the functions which contain these warnings invoke mutex_lock() which contains a broad variety of checks (always enabled or debug option dependent) and therefore covers all invalid conditions already, there is no point in having inconsistent warnings in those drivers. The conditional return is not really valuable in practice either. Just remove them. Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mdiobus: add reset-post-delay-us handlingBruno Thomsen
Load new "reset-post-delay-us" value from MDIO properties, and if configured to a greater then zero delay do a flexible sleeping delay after MDIO bus reset deassert. This allows devices to exit reset state before start bus communication. Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-08-03net: mdiobus: use flexible sleeping for reset-delay-usBruno Thomsen
MDIO bus reset pulse width is created by using udelay() and that function might not be optimal depending on device tree value. By switching to the new fsleep() helper the correct delay function is called depending on delay length, e.g. udelay(), usleep_range() or msleep(). Signed-off-by: Bruno Thomsen <bruno.thomsen@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-30net: phy: don't abuse devres in devm_mdiobus_register()Bartosz Golaszewski
We currently have two managed helpers for mdiobus - devm_mdiobus_alloc() and devm_mdiobus_register(). The idea behind devres is that the release callback releases whatever resource the devm function allocates. In the mdiobus case however there's no devres associated with the device by devm_mdiobus_register(). Instead the release callback for devm_mdiobus_alloc(): _devm_mdiobus_free() unregisters the device if it is marked as managed. This all seems wrong. The managed structure shouldn't need to know or care about whether it's managed or not - and this is the case now for struct mii_bus. The devres wrapper should be opaque to the managed resource. This changeset makes devm_mdiobus_alloc() and devm_mdiobus_register() conform to common devres standards: devm_mdiobus_alloc() allocates a devres structure and registers a callback that will call mdiobus_free(). __devm_mdiobus_register() allocated another devres and registers a callback that will unregister the bus. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-26net: phy: arrange headers in mdio_bus.c alphabeticallyBartosz Golaszewski
Keeping the headers in alphabetical order is better for readability and allows to easily see if given header is already included. Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-23net: phy: Allow mdio buses to auto-probe c45 devicesJeremy Linton
The mdiobus_scan logic is currently hardcoded to only work with c22 devices. This works fairly well in most cases, but its possible that a c45 device doesn't respond despite being a standard phy. If the parent hardware is capable, it makes sense to scan for c22 devices before falling back to c45. As we want this to reflect the capabilities of the STA, lets add a field to the mii_bus structure to represent the capability. That way devices can opt into the extended scanning. Existing users should continue to default to c22 only scanning as long as they are zero'ing the structure before use. Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Signed-off-by: Calvin Johnson <calvin.johnson@oss.nxp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-06-04net: mdiobus: Disable preemption upon u64_stats updateAhmed S. Darwish
The u64_stats mechanism uses sequence counters to protect against 64-bit values tearing on 32-bit architectures. Updating u64_stats is thus a sequence counter write side critical section where preemption must be disabled. For mdiobus_stats_acct(), disable preemption upon the u64_stats update. It is called from process context through mdiobus_read() and mdiobus_write(). Reported-by: kernel test robot <lkp@intel.com> Signed-off-by: Ahmed S. Darwish <a.darwish@linutronix.de> Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-05-06net: phy: add concept of shared storage for PHYsMichael Walle
There are packages which contain multiple PHY devices, eg. a quad PHY transceiver. Provide functions to allocate and free shared storage. Usually, a quad PHY contains global registers, which don't belong to any PHY. Provide convenience functions to access these registers. Signed-off-by: Michael Walle <michael@walle.cc> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: Use IS_ERR() to check and simplify codeTang Bin
Use IS_ERR() and PTR_ERR() instead of PTR_ZRR_OR_ZERO() to simplify code, avoid redundant paramenter definitions and judgements. Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com> Signed-off-by: Tang Bin <tangbin@cmss.chinamobile.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-22net: phy: add device-managed devm_mdiobus_registerHeiner Kallweit
If there's no special ordering requirement for mdiobus_unregister(), then driver code can be simplified by using a device-managed version of mdiobus_register(). Prerequisite is that bus allocation has been done device-managed too. Else mdiobus_free() may be called whilst bus is still registered, resulting in a BUG_ON(). Therefore let devm_mdiobus_register() return -EPERM if bus was allocated non-managed. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-20net: phy: Propagate error from bus->resetFlorian Fainelli
If a bus->reset() call for the mii_bus structure returns an error (e.g.: -EPROE_DEFER) we should propagate it accordingly. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-04-07Documentation: mdio_bus.c - fix warningsLothar Rubusch
Fix wrong parameter description and related warnings at 'make htmldocs'. Signed-off-by: Lothar Rubusch <l.rubusch@gmail.com> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Acked-by: Randy Dunlap <rdunlap@infradead.org> Tested-by: Randy Dunlap <rdunlap@infradead.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-17net: mdiobus: add APIs for modifying a MDIO device registerRussell King
Add APIs for modifying a MDIO device register, similar to the existing phy_modify() group of functions, but at mdiobus level instead. Adapt __phy_modify_changed() to use the new mdiobus level helper. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-03-17net: mdiobus: avoid BUG_ON() in mdiobus accessorsRussell King
Avoid using BUG_ON() in the mdiobus accessors, prefering instead to use WARN_ON_ONCE() and returning an error. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-02-24mdio_bus: Add generic mdio_find_bus()Jeremy Linton
It appears most ethernet drivers follow one of two main strategies for mdio bus/phy management. A monolithic model where the net driver itself creates, probes and uses the phy, and one where an external mdio/phy driver instantiates the mdio bus/phy and the net driver only attaches to a known phy. Usually in this latter model the phys are discovered via DT relationships or simply phy name/address hardcoding. This is a shame because modern well behaved mdio buses are self describing and can be probed. The mdio layer itself is fully capable of this, yet there isn't a clean way for a standalone net driver to attach and enumerate the discovered devices. This is because outside of of_mdio_find_bus() there isn't a straightforward way to acquire the mii_bus pointer. So, lets add a mdio_find_bus which can return the mii_bus based only on its name. Signed-off-by: Jeremy Linton <jeremy.linton@arm.com> Acked-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-17net: phy: Maintain MDIO device and bus statisticsFlorian Fainelli
We maintain global statistics for an entire MDIO bus, as well as broken down, per MDIO bus address statistics. Given that it is possible for MDIO devices such as switches to access MDIO bus addresses for which there is not a mdio_device instance created (therefore not a a corresponding device directory in sysfs either), we also maintain per-address statistics under the statistics folder. The layout looks like this: /sys/class/mdio_bus/../statistics/ transfers errrors writes reads transfers_<addr> errors_<addr> writes_<addr> reads_<addr> When a mdio_device instance is registered, a statistics/ folder is created with the tranfers, errors, writes and reads attributes which point to the appropriate MDIO bus statistics structure. Statistics are 64-bit unsigned quantities and maintained through the u64_stats_sync.h helper functions. Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Tested-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2020-01-14mdio_bus: Simplify reset handling and extend to non-DT systemsGeert Uytterhoeven
Convert mdiobus_register_reset() from open-coded DT-only optional reset handling to reset_control_get_optional_exclusive(). This not only simplifies the code, but also adds support for lookup-based resets on non-DT systems. Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-25mdio_bus: don't use managed reset-controllerDavid Bauer
Geert Uytterhoeven reported that using devm_reset_controller_get leads to a WARNING when probing a reset-controlled PHY. This is because the device devm_reset_controller_get gets supplied is not actually the one being probed. Acquire an unmanaged reset-control as well as free the reset_control on unregister to fix this. Reported-by: Geert Uytterhoeven <geert@linux-m68k.org> CC: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-11-19mdio_bus: Fix init if CONFIG_RESET_CONTROLLER=nGeert Uytterhoeven
Commit 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") accidentally changed a check from -ENOTSUPP to -ENOSYS, causing failures if reset controller support is not enabled. E.g. on r7s72100/rskrza1: sh-eth e8203000.ethernet: MDIO init failed: -524 sh-eth: probe of e8203000.ethernet failed with error -524 Seen on r8a7740/armadillo, r7s72100/rskrza1, and r7s9210/rza2mevb. Fixes: 1d4639567d97 ("mdio_bus: Fix PTR_ERR applied after initialization to constant") Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Cc: YueHaibing <yuehaibing@huawei.com> Cc: David S. Miller <davem@davemloft.net> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2019-11-11mdio_bus: Fix PTR_ERR applied after initialization to constantYueHaibing
Fix coccinelle warning: ./drivers/net/phy/mdio_bus.c:67:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 ./drivers/net/phy/mdio_bus.c:68:5-12: ERROR: PTR_ERR applied after initialization to constant on line 62 Fix this by using IS_ERR before PTR_ERR Reported-by: Hulk Robot <hulkci@huawei.com> Fixes: 71dd6c0dff51 ("net: phy: add support for reset-controller") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-09-18Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-nextLinus Torvalds
Pull networking updates from David Miller: 1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski. 2) Use bio_vec in the networking instead of custom skb_frag_t, from Matthew Wilcox. 3) Make use of xmit_more in r8169 driver, from Heiner Kallweit. 4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen. 5) Support all variants of 5750X bnxt_en chips, from Michael Chan. 6) More RTNL avoidance work in the core and mlx5 driver, from Vlad Buslov. 7) Add TCP syn cookies bpf helper, from Petar Penkov. 8) Add 'nettest' to selftests and use it, from David Ahern. 9) Add extack support to drop_monitor, add packet alert mode and support for HW drops, from Ido Schimmel. 10) Add VLAN offload to stmmac, from Jose Abreu. 11) Lots of devm_platform_ioremap_resource() conversions, from YueHaibing. 12) Add IONIC driver, from Shannon Nelson. 13) Several kTLS cleanups, from Jakub Kicinski. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits) mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer mlxsw: spectrum: Register CPU port with devlink mlxsw: spectrum_buffers: Prevent changing CPU port's configuration net: ena: fix incorrect update of intr_delay_resolution net: ena: fix retrieval of nonadaptive interrupt moderation intervals net: ena: fix update of interrupt moderation register net: ena: remove all old adaptive rx interrupt moderation code from ena_com net: ena: remove ena_restore_ethtool_params() and relevant fields net: ena: remove old adaptive interrupt moderation code from ena_netdev net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*() net: ena: enable the interrupt_moderation in driver_supported_features net: ena: reimplement set/get_coalesce() net: ena: switch to dim algorithm for rx adaptive interrupt moderation net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable ethtool: implement Energy Detect Powerdown support via phy-tunable xen-netfront: do not assume sk_buff_head list is empty in error handling s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb” net: ena: don't wake up tx queue when down drop_monitor: Better sanitize notified packets ...
2019-09-16net: mdio: switch to using gpiod_get_optional()Dmitry Torokhov
The MDIO device reset line is optional and now that gpiod_get_optional() returns proper value when GPIO support is compiled out, there is no reason to use fwnode_get_named_gpiod() that I plan to hide away. Let's switch to using more standard gpiod_get_optional() and gpiod_set_consumer_name() to keep the nice "PHY reset" label. Also there is no reason to only try to fetch the reset GPIO when we have OF node, gpiolib can fetch GPIO data from firmwares as well. Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-07-30drivers: Introduce device lookup variants by of_nodeSuzuki K Poulose
Introduce wrappers for {bus/driver/class}_find_device() to locate devices by its of_node. Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com> Cc: Maxime Ripard <maxime.ripard@bootlin.com> Cc: dri-devel@lists.freedesktop.org Cc: David Airlie <airlied@linux.ie> Cc: Daniel Vetter <daniel@ffwll.ch> Cc: devicetree@vger.kernel.org Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Frank Rowand <frowand.list@gmail.com> Cc: Heiko Stuebner <heiko@sntech.de> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: linux-i2c@vger.kernel.org Cc: linux-rockchip@lists.infradead.org Cc: linux-spi@vger.kernel.org Cc: Mathieu Poirier <mathieu.poirier@linaro.org> Cc: Rob Herring <robh+dt@kernel.org> Cc: Srinivas Kandagatla <srinivas.kandagatla@linaro.org> Cc: Takashi Iwai <tiwai@suse.com> Cc: Alan Tull <atull@kernel.org> Cc: linux-fpga@vger.kernel.org Cc: Peter Rosin <peda@axentia.se> Cc: Florian Fainelli <f.fainelli@gmail.com> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: "David S. Miller" <davem@davemloft.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Liam Girdwood <lgirdwood@gmail.com> Cc: "Rafael J. Wysocki" <rafael@kernel.org> Cc: Thor Thayer <thor.thayer@linux.intel.com> Cc: Jiri Slaby <jslaby@suse.com> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Peter Rosin <peda@axentia.se> Signed-off-by: Suzuki K Poulose <suzuki.poulose@arm.com> Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Wolfram Sang <wsa@the-dreams.de> # I2C part Acked-by: Moritz Fischer <mdf@kernel.org> # For FPGA part Acked-by: Mark Brown <broonie@kernel.org> Link: https://lore.kernel.org/r/20190723221838.12024-3-suzuki.poulose@arm.com Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2019-04-18net: mdio: rename mdio_device reset to reset_gpioDavid Bauer
This renames the GPIO reset of mdio devices from 'reset' to 'reset_gpio' to better differentiate between GPIO and reset-controller driven reset line. Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-04-18net: phy: add support for reset-controllerDavid Bauer
This commit adds support for PHY reset pins handled by a reset controller. Signed-off-by: David Bauer <mail@david-bauer.net> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-24Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three conflicts, one of which, for marvell10g.c is non-trivial and requires some follow-up from Heiner or someone else. The issue is that Heiner converted the marvell10g driver over to use the generic c45 code as much as possible. However, in 'net' a bug fix appeared which makes sure that a new local mask (MDIO_AN_10GBT_CTRL_ADV_NBT_MASK) with value 0x01e0 is cleared. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-22mdio_bus: Fix use-after-free on device_register failsYueHaibing
KASAN has found use-after-free in fixed_mdio_bus_init, commit 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") call put_device() while device_register() fails,give up the last reference to the device and allow mdiobus_release to be executed ,kfreeing the bus. However in most drives, mdiobus_free be called to free the bus while mdiobus_register fails. use-after-free occurs when access bus again, this patch revert it to let mdiobus_free free the bus. KASAN report details as below: BUG: KASAN: use-after-free in mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482 Read of size 4 at addr ffff8881dc824d78 by task syz-executor.0/3524 CPU: 1 PID: 3524 Comm: syz-executor.0 Not tainted 5.0.0-rc7+ #45 Hardware name: QEMU Standard PC (i440FX + PIIX, 1996), BIOS 1.10.2-1ubuntu1 04/01/2014 Call Trace: __dump_stack lib/dump_stack.c:77 [inline] dump_stack+0xfa/0x1ce lib/dump_stack.c:113 print_address_description+0x65/0x270 mm/kasan/report.c:187 kasan_report+0x149/0x18d mm/kasan/report.c:317 mdiobus_free+0x85/0x90 drivers/net/phy/mdio_bus.c:482 fixed_mdio_bus_init+0x283/0x1000 [fixed_phy] ? 0xffffffffc0e40000 ? 0xffffffffc0e40000 ? 0xffffffffc0e40000 do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe RIP: 0033:0x462e99 Code: f7 d8 64 89 02 b8 ff ff ff ff c3 66 0f 1f 44 00 00 48 89 f8 48 89 f7 48 89 d6 48 89 ca 4d 89 c2 4d 89 c8 4c 8b 4c 24 08 0f 05 <48> 3d 01 f0 ff ff 73 01 c3 48 c7 c1 bc ff ff ff f7 d8 64 89 01 48 RSP: 002b:00007f6215c19c58 EFLAGS: 00000246 ORIG_RAX: 0000000000000139 RAX: ffffffffffffffda RBX: 000000000073bf00 RCX: 0000000000462e99 RDX: 0000000000000000 RSI: 0000000020000080 RDI: 0000000000000003 RBP: 00007f6215c19c70 R08: 0000000000000000 R09: 0000000000000000 R10: 0000000000000000 R11: 0000000000000246 R12: 00007f6215c1a6bc R13: 00000000004bcefb R14: 00000000006f7030 R15: 0000000000000004 Allocated by task 3524: set_track mm/kasan/common.c:85 [inline] __kasan_kmalloc.constprop.3+0xa0/0xd0 mm/kasan/common.c:496 kmalloc include/linux/slab.h:545 [inline] kzalloc include/linux/slab.h:740 [inline] mdiobus_alloc_size+0x54/0x1b0 drivers/net/phy/mdio_bus.c:143 fixed_mdio_bus_init+0x163/0x1000 [fixed_phy] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe Freed by task 3524: set_track mm/kasan/common.c:85 [inline] __kasan_slab_free+0x130/0x180 mm/kasan/common.c:458 slab_free_hook mm/slub.c:1409 [inline] slab_free_freelist_hook mm/slub.c:1436 [inline] slab_free mm/slub.c:2986 [inline] kfree+0xe1/0x270 mm/slub.c:3938 device_release+0x78/0x200 drivers/base/core.c:919 kobject_cleanup lib/kobject.c:662 [inline] kobject_release lib/kobject.c:691 [inline] kref_put include/linux/kref.h:67 [inline] kobject_put+0x146/0x240 lib/kobject.c:708 put_device+0x1c/0x30 drivers/base/core.c:2060 __mdiobus_register+0x483/0x560 drivers/net/phy/mdio_bus.c:382 fixed_mdio_bus_init+0x26b/0x1000 [fixed_phy] do_one_initcall+0xfa/0x5ca init/main.c:887 do_init_module+0x204/0x5f6 kernel/module.c:3460 load_module+0x66b2/0x8570 kernel/module.c:3808 __do_sys_finit_module+0x238/0x2a0 kernel/module.c:3902 do_syscall_64+0x147/0x600 arch/x86/entry/common.c:290 entry_SYSCALL_64_after_hwframe+0x49/0xbe The buggy address belongs to the object at ffff8881dc824c80 which belongs to the cache kmalloc-2k of size 2048 The buggy address is located 248 bytes inside of 2048-byte region [ffff8881dc824c80, ffff8881dc825480) The buggy address belongs to the page: page:ffffea0007720800 count:1 mapcount:0 mapping:ffff8881f6c02800 index:0x0 compound_mapcount: 0 flags: 0x2fffc0000010200(slab|head) raw: 02fffc0000010200 0000000000000000 0000000500000001 ffff8881f6c02800 raw: 0000000000000000 00000000800f000f 00000001ffffffff 0000000000000000 page dumped because: kasan: bad access detected Memory state around the buggy address: ffff8881dc824c00: fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc fc ffff8881dc824c80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb >ffff8881dc824d00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ^ ffff8881dc824d80: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb ffff8881dc824e00: fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb fb Fixes: 0c692d07842a ("drivers/net/phy/mdio_bus.c: call put_device on device_register() failure") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-02-18mdio_bus: Fix PTR_ERR() usage after initialization to constantYueHaibing
Fix coccinelle warning: ./drivers/net/phy/mdio_bus.c:51:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44 ./drivers/net/phy/mdio_bus.c:52:5-12: ERROR: PTR_ERR applied after initialization to constant on line 44 fix this by using IS_ERR before PTR_ERR Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-22net: phy: Convert some PHY and MDIO driver files to SPDX headersAndrew Lunn
Where the license text and the MODULE_LICENSE() value agree, convert to using an SPDX header, removing the license text. Signed-off-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-21Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Completely minor snmp doc conflict. Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-18net: phy: mdio_bus: add missing device_del() in mdiobus_register() error ↵Thomas Petazzoni
handling The current code in __mdiobus_register() doesn't properly handle failures returned by the devm_gpiod_get_optional() call: it returns immediately, without unregistering the device that was added by the call to device_register() earlier in the function. This leaves a stale device, which then causes a NULL pointer dereference in the code that handles deferred probing: [ 1.489982] Unable to handle kernel NULL pointer dereference at virtual address 00000074 [ 1.498110] pgd = (ptrval) [ 1.500838] [00000074] *pgd=00000000 [ 1.504432] Internal error: Oops: 17 [#1] SMP ARM [ 1.509133] Modules linked in: [ 1.512192] CPU: 1 PID: 51 Comm: kworker/1:3 Not tainted 4.20.0-00039-g3b73a4cc8b3e-dirty #99 [ 1.520708] Hardware name: Xilinx Zynq Platform [ 1.525261] Workqueue: events deferred_probe_work_func [ 1.530403] PC is at klist_next+0x10/0xfc [ 1.534403] LR is at device_for_each_child+0x40/0x94 [ 1.539361] pc : [<c0683fbc>] lr : [<c0455d90>] psr: 200e0013 [ 1.545628] sp : ceeefe68 ip : 00000001 fp : ffffe000 [ 1.550863] r10: 00000000 r9 : c0c66790 r8 : 00000000 [ 1.556079] r7 : c0457d44 r6 : 00000000 r5 : ceeefe8c r4 : cfa2ec78 [ 1.562604] r3 : 00000064 r2 : c0457d44 r1 : ceeefe8c r0 : 00000064 [ 1.569129] Flags: nzCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none [ 1.576263] Control: 18c5387d Table: 0ed7804a DAC: 00000051 [ 1.582013] Process kworker/1:3 (pid: 51, stack limit = 0x(ptrval)) [ 1.588280] Stack: (0xceeefe68 to 0xceef0000) [ 1.592630] fe60: cfa2ec78 c0c03c08 00000000 c0457d44 00000000 c0c66790 [ 1.600814] fe80: 00000000 c0455d90 ceeefeac 00000064 00000000 0d7a542e cee9d494 cfa2ec78 [ 1.608998] fea0: cfa2ec78 00000000 c0457d44 c0457d7c cee9d494 c0c03c08 00000000 c0455dac [ 1.617182] fec0: cf98ba44 cf926a00 cee9d494 0d7a542e 00000000 cf935a10 cf935a10 cf935a10 [ 1.625366] fee0: c0c4e9b8 c0457d7c c0c4e80c 00000001 cf935a10 c0457df4 cf935a10 c0c4e99c [ 1.633550] ff00: c0c4e99c c045a27c c0c4e9c4 ced63f80 cfde8a80 cfdebc00 00000000 c013893c [ 1.641734] ff20: cfde8a80 cfde8a80 c07bd354 ced63f80 ced63f94 cfde8a80 00000008 c0c02d00 [ 1.649936] ff40: cfde8a98 cfde8a80 ffffe000 c0139a30 ffffe000 c0c6624a c07bd354 00000000 [ 1.658120] ff60: ffffe000 cee9e780 ceebfe00 00000000 ceeee000 ced63f80 c0139788 cf8cdea4 [ 1.666304] ff80: cee9e79c c013e598 00000001 ceebfe00 c013e44c 00000000 00000000 00000000 [ 1.674488] ffa0: 00000000 00000000 00000000 c01010e8 00000000 00000000 00000000 00000000 [ 1.682671] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.690855] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 00000000 00000000 [ 1.699058] [<c0683fbc>] (klist_next) from [<c0455d90>] (device_for_each_child+0x40/0x94) [ 1.707241] [<c0455d90>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.716476] [<c0457d7c>] (device_reorder_to_tail) from [<c0455dac>] (device_for_each_child+0x5c/0x94) [ 1.725692] [<c0455dac>] (device_for_each_child) from [<c0457d7c>] (device_reorder_to_tail+0x38/0x88) [ 1.734927] [<c0457d7c>] (device_reorder_to_tail) from [<c0457df4>] (device_pm_move_to_tail+0x28/0x40) [ 1.744235] [<c0457df4>] (device_pm_move_to_tail) from [<c045a27c>] (deferred_probe_work_func+0x58/0x8c) [ 1.753746] [<c045a27c>] (deferred_probe_work_func) from [<c013893c>] (process_one_work+0x210/0x4fc) [ 1.762888] [<c013893c>] (process_one_work) from [<c0139a30>] (worker_thread+0x2a8/0x5c0) [ 1.771072] [<c0139a30>] (worker_thread) from [<c013e598>] (kthread+0x14c/0x154) [ 1.778482] [<c013e598>] (kthread) from [<c01010e8>] (ret_from_fork+0x14/0x2c) [ 1.785689] Exception stack(0xceeeffb0 to 0xceeefff8) [ 1.790739] ffa0: 00000000 00000000 00000000 00000000 [ 1.798923] ffc0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000 [ 1.807107] ffe0: 00000000 00000000 00000000 00000000 00000013 00000000 [ 1.813724] Code: e92d47f0 e1a05000 e8900048 e1a00003 (e5937010) [ 1.819844] ---[ end trace 3c2c0c8b65399ec9 ]--- The actual error that we had from devm_gpiod_get_optional() was -EPROBE_DEFER, due to the GPIO being provided by a driver that is probed later than the Ethernet controller driver. To fix this, we simply add the missing device_del() invocation in the error path. Fixes: 69226896ad636 ("mdio_bus: Issue GPIO RESET to PHYs") Signed-off-by: Thomas Petazzoni <thomas.petazzoni@bootlin.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2019-01-16net: phy: don't include asm/irq.h directlyHeiner Kallweit
There's no need to and one shouldn't include asm/irq.h directly. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-09-17net: mdio: remove duplicated include from mdio_bus.cYueHaibing
Remove duplicated include linux/gpio/consumer.h Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-06-05net: phy: remove PM ops from MDIO busHeiner Kallweit
Current implementation of MDIO bus PM ops doesn't actually implement bus-specific PM ops but just calls PM ops defined on a device level what doesn't seem to be fully in line with the core PM model. When looking e.g. at __device_suspend() the PM core looks for PM ops of a device in a specific order: 1. device PM domain 2. device type 3. device class 4. device bus I think it has good reason that there's no PM ops on device level. Now that a device type representation of PHY's as special type of MDIO devices was added (only user of MDIO bus PM ops), the MDIO bus PM ops can be removed including member pm of struct mdio_device. If for some other type of MDIO device PM ops are needed, it should be modeled as struct device_type as well. Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-02-06net: phy: Handle not having GPIO enabled in the kernelAndrew Lunn
If CONFIG_GPIOLIB is disabled, fwnode_get_named_gpiod() becomes a stub function, which return -ENOSYS. Handle this in the same way as -ENOENT, i.e. assume there is no GPIO used to reset the PHYs. Reported-by: Christian Zigotzky <chzigotzky@xenosoft.de> Tested-by: Christian Zigotzky <chzigotzky@xenosoft.de> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-03net: mdio: Only perform gpio reset for PHYsAndrew Lunn
Ethernet switch on the MDIO bus have historically performed their own handling of the GPIO reset line. The resent patch to have the MDIO core handle the reset has broken the switch drivers, in that they cannot claim the GPIO. Some switch drivers need more control over the GPIO line than what the MDIO core provides. So restore the historical behaviour by only performing a reset of PHYs, not switches. Fixes: bafbdd527d56 ("phylib: Add device reset GPIO support") Reported-by: Sean Wang <sean.wang@mediatek.com> Signed-off-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Geert Uytterhoeven <geert+renesas@glider.be> Signed-off-by: David S. Miller <davem@davemloft.net>
2018-01-03net: mdiobus: add unlocked accessorsRussell King
Add unlocked versions of the bus accessors, which allows access to the bus with all the tracing. These accessors validate that the bus mutex is held, which is a basic requirement for all mii bus accesses. Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-16Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Three sets of overlapping changes, two in the packet scheduler and one in the meson-gxl PHY driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-13of_mdio / mdiobus: ensure mdio devices have fwnode correctly populatedRussell King
Ensure that all mdio devices populate the struct device fwnode pointer as well as the of_node pointer to allow drivers that wish to use fwnode APIs to work. Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk> Reviewed-by: Rob Herring <robh@kernel.org> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-12-05phylib: Add device reset GPIO supportSergei Shtylyov
The PHY devices sometimes do have their reset signal (maybe even power supply?) tied to some GPIO and sometimes it also does happen that a boot loader does not leave it deasserted. So far this issue has been attacked from (as I believe) a wrong angle: by teaching the MAC driver to manipulate the GPIO in question; that solution, when applied to the device trees, led to adding the PHY reset GPIO properties to the MAC device node, with one exception: Cadence MACB driver which could handle the "reset-gpios" prop in a PHY device subnode. I believe that the correct approach is to teach the 'phylib' to get the MDIO device reset GPIO from the device tree node corresponding to this device -- which this patch is doing... Note that I had to modify the AT803x PHY driver as it would stop working otherwise -- it made use of the reset GPIO for its own purposes... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Acked-by: Rob Herring <robh@kernel.org> [geert: Propagate actual errors from fwnode_get_named_gpiod()] [geert: Avoid destroying initial setup] [geert: Consolidate GPIO descriptor acquiring code] Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be> Tested-by: Richard Leitner <richard.leitner@skidata.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-09-08Revert "mdio_bus: Remove unneeded gpiod NULL check"Florian Fainelli
This reverts commit 95b80bf3db03c2bf572a357cf74b9a6aefef0a4a ("mdio_bus: Remove unneeded gpiod NULL check"), this commit assumed that GPIOLIB checks for NULL descriptors, so it's safe to drop them, but it is not when CONFIG_GPIOLIB is disabled in the kernel. If we do call gpiod_set_value_cansleep() on a GPIO descriptor we will issue warnings coming from the inline stubs declared in include/linux/gpio/consumer.h. Fixes: 95b80bf3db03 ("mdio_bus: Remove unneeded gpiod NULL check") Reported-by: Woojung Huh <Woojung.Huh@microchip.com> Signed-off-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-07-17mdio_bus: Remove unneeded gpiod NULL checkFabio Estevam
The gpiod API checks for NULL descriptors, so there is no need to duplicate the check in the driver. Signed-off-by: Fabio Estevam <fabio.estevam@nxp.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13mdio_bus: use devm_gpiod_get_optional()Sergei Shtylyov
The MDIO reset GPIO is really a classical optional GPIO property case, so devm_gpiod_get_optional() should have been used, not devm_gpiod_get(). Doing this saves several LoCs... Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-13mdio_bus: handle only single PHY reset GPIOSergei Shtylyov
Commit 4c5e7a2c0501 ("dt-bindings: mdio: Clarify binding document") declared that a MDIO reset GPIO property should have only a single GPIO reference/specifier, however the supporting code was left intact, still burdening the kernel with now apparently useless loops -- get rid of them. Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-06Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Just some simple overlapping changes in marvell PHY driver and the DSA core code. Signed-off-by: David S. Miller <davem@davemloft.net>
2017-06-02net: phy: use of_mdio_parse_addrJon Mason
use of_mdio_parse_addr() in place of an OF read of reg and a bounds check (which is litterally the exact same thing that of_mdio_parse_addr() does) Signed-off-by: Jon Mason <jon.mason@broadcom.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Reviewed-by: Florian Fainelli <f.fainelli@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>