Age | Commit message (Collapse) | Author |
|
BCM72116 features a 28nm integrated EPHY, add an entry to match this PHY
OUI.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20210106170944.1253046-1-f.fainelli@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
BCM72113 features a 28nm integrated EPHY, add an entry to the driver for
it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal Gigabit PHY on Broadcom STB chips has a digital clock which
drives its MDIO interface among other things, the driver now requests
and manage that clock during .probe() and .remove() accordingly.
Because the PHY driver can be probed with the clocks turned off we need
to apply the dummy BMSR workaround during the driver probe function to
ensure subsequent MDIO read or write towards the PHY will succeed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM7XX PHY family requires special configuration to pass jumbo
frames. Do that during initial PHY setup.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The internal 40nm EPHYs use a "Workaround for putting the PHY in
IDDQ mode." These PHYs require a soft reset to restore functionality
after they are powered back up.
This commit defines the soft_reset function to use genphy_soft_reset
during phy_init_hw to accommodate this.
Fixes: 6e2d85ec0559 ("net: phy: Stop with excessive soft reset")
Signed-off-by: Doug Berger <opendmb@gmail.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently genphy_read_abilities() has been added that dynamically detects
clause 22 PHY abilities. I *think* this detection should work with all
supported PHY's, at least for the ones with basic features sets, i.e.
PHY_BASIC_FEATURES and PHY_GBIT_FEATURES. So let's remove setting these
features explicitly and rely on phylib feature detection.
I don't have access to most of these PHY's, therefore I'd appreciate
regression testing.
v2:
- make the feature constant a comment so that readers know which
features are supported by the respective PHY
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Tested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cygnus and Omega are part of the same business unit and product line, it
makes sense to group PHY entries by products such that a platform can
select only the drivers that it needs. Bring all the functionality that
the BCM7XXX_28NM_GPHY() macro hides for us and remove the Omega PHY
entry from bcm7xxx.c.
As an added bonus, we now have a proper mdio_device_id entry to permit
auto-loading.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Omega PHY entry was added to bcm7xxx.c out of convenience and this
breaks the one driver per product line paradigm that was applied up
until now. Since the AFE initialization is shared between Omega and
BCM7xxx move the relevant functions to bcm-phy-lib.[ch]. No functional
changes introduced.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Where the license text and the MODULE_LICENSE() value agree, convert
to using an SPDX header, removing the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for BCM7255 EPHY.
Signed-off-by: Justin Chen <justinpopo6@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Broadcom Omega SoC internal Combo Ethernet
GPHY to the bcm7xxx phy driver.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On newer PHYs, we need to select the expansion register to write with
setting bits [11:8] to 0xf. This was done correctly by bcm7xxx.c prior
to being migrated to generic code under bcm-phy-lib.c which
unfortunately used the older implementation from the BCM54xx days.
Fix this by creating an inline stub: bcm_write_exp_sel() which adds the
correct value (MII_BCM54XX_EXP_SEL_ER) and update both the Cygnus PHY
and BCM7xxx PHY drivers which require setting these bits.
broadcom.c is unchanged because some PHYs even use a different selector
method, so let them specify it directly (e.g: SerDes secondary selector).
Fixes: a1cba5613edf ("net: phy: Add Broadcom phy library for common interfaces")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in comments and error message text.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
from drivers
Remove generic settings for callbacks config_aneg and read_status
from drivers.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
code size
Don't populate the array bcm7xxx_suspend_cfg A on the stack, instead
make it static. Makes the object code smaller by over 300 bytes:
Before:
text data bss dec hex filename
6351 8146 0 14497 38a1 drivers/net/phy/bcm7xxx.o
After:
text data bss dec hex filename
5986 8210 0 14196 3774 drivers/net/phy/bcm7xxx.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds support for the internal fast ethernet 10/100 PHY
found in the BCM7260, BCM7268, and BCM7271 devices.
Signed-off-by: Doug Berger <opendmb@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add the BCM74371 PHY ID to the list of supported chips. This is a 28nm
technology Gigabit PHY SoC.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Implement the HW design team recommended workaround in for 7278. Since
the GPHY now returns its revision information in MII_PHYS_ID[23] we need
to check whether the revision provided in flags is 0 or not.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the BCM7278 28nm process Gigabit Ethernet PHY.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Instead of having individual PHY drivers set the SUPPORTED_Pause and
SUPPORTED_Asym_Pause flags, phylib itself should set those flags,
unless there is a hardware erratum or other special case. During
autonegotiation, the PHYs will determine whether to enable pause
frame support.
Pause frames are a feature that is supported by the MAC. It is the MAC
that generates the frames and that processes them. The PHY can only be
configured to allow them to pass through.
This commit also effectively reverts the recently applied c7a61319
("net: phy: dp83848: Support ethernet pause frames").
So the new process is:
1) Unless the PHY driver overrides it, phylib sets the SUPPORTED_Pause
and SUPPORTED_AsymPause bits in phydev->supported. This indicates that
the PHY supports pause frames.
2) The MAC driver checks phydev->supported before it calls phy_start().
If (SUPPORTED_Pause | SUPPORTED_AsymPause) is set, then the MAC driver
sets those bits in phydev->advertising, if it wants to enable pause
frame support.
3) When the link state changes, the MAC driver checks phydev->pause and
phydev->asym_pause, If the bits are set, then it enables the corresponding
features in the MAC. The algorithm is:
if (phydev->pause)
The MAC should be programmed to receive and honor
pause frames it receives, i.e. enable receive flow control.
if (phydev->pause != phydev->asym_pause)
The MAC should be programmed to transmit pause
frames when needed, i.e. enable transmit flow control.
Signed-off-by: Timur Tabi <timur@codeaurora.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Broadcom BCM7xxx internal PHYs can leverage the Broadcom PHY library
module PHY error counters helper functions, just implement the
appropriate PHY driver function calls to do so. We need to allocate some
storage space for our PHY statistics, and provide it to the Broadcom PHY
library, so do this in a specific probe function, and slightly wrap the
get_stats function call.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for configuring the downshift/Wirespeed enable/disable
toggles and specify a link retry value ranging from 1 to 9. Since the
integrated BCM7xxx have issues when wirespeed is enabled and EEE is also
enabled, we do disable EEE if wirespeed is enabled.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for adding support for Wirespeed/downshift, we need to
change bcm_phy_eee_enable() to allow enabling or disabling EEE, so make
the function take an extra enable/disable boolean parameter and rename
it to illustrate it sets EEE, not necessarily just enables it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add PHY entries for the Broadcom BCM7346 and BCM7362 chips, these are
40nm generation Ethernet PHY.
Fixes: 815717d1473e ("net: phy: bcm7xxx: Remove wildcard entries")
Signed-off-by: Jaedon Shin <jaedon.shin@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce a macro which helps adding new 40NM EPHY entries and reduces the
amount of boilerplate code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver is BCM7xxx, we were missing an additional X in the constant naming,
fix that to be consistent.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the two wildcard entries, they serve no purpose and will match way too
many devices, some of them being covered by the driver in
drivers/net/phy/broadcom.c. Remove the now unused bcm7xxx_dummy_config_init()
function which would produce a warning.
Fixes: b560a58c45c6 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since we were wrongly advertising gigabit features for these 10/100 only
Ethernet PHYs, bcm7xxx_config_init() which is supposed to apply workaround
would have not run since the check would be true, now that we have fixed the
PHY features, remove that check since it has no reasoning to be there anymore.
Fixes: e18556ee3bd83 ("net: phy: bcm7xxx: do not use PHY_BRCM_100MBPS_WAR")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PHY entries for BCM7425/29/35 declare the 40nm Ethernet PHY as being
10/100/1000 capable, while this is just a 10/100 capable PHY device, fix that.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs")
Fixes: 9458ceab4917 ("net: phy: bcm7xxx: Add entry for BCM7435")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The clear and set masks in the call to phy_set_clr_bits() called from
bcm7xxx_config_init() are inverted. We need to fix this by swapping the two
arguments, that is, set 0 bits, but clear the shade mode 2 enable bit.
Fixes: b560a58c45c66 ("net: phy: add Broadcom BCM7xxx internal PHY driver")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rather than have each driver set the driver owner field, do it once in
the core code. This will also help with later changes, when the device
structure will move.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a phydev_name() function, to help with moving some structure members
from phy_device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a PHY entry for the Broadcom BCM7435 chips, this is a 40nm
generation Ethernet PHY which is analogous to its 7425 and 7429 counter
parts.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Modified the bcm7xxx phy driver to remove local core register
defines and use the common ones from "include/linux/brcmphy.h"
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the Broadcom phy library to consolidate common
interfaces shared by Broadcom phy's.
Moved the common interfaces to the 'bcm-phy-lib.c' and updated
the Broadcom PHY drivers to use the new APIs.
Signed-off-by: Arun Parameswaran <arunp@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The initial MDIO read or write towards the BCM7xxx integrated PHY may
fail, workaround this by inserting a dummy MII_BMSR read to force the
MDIO management controller to see at least one valid transaction and get
out of stuck state out of reset.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the AFE_TX_CONFIG value to solve marginal rise/fall issues
observed when the link is operating in 100BaseT. This workaround applies
to GPHY revisions D0, E0 and newer.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While adding support for 7425 PHY in the 7xxx PHY driver, the ID that
was used was actually coming from an external PHY: a BCM5461x. Fix this
by using the proper ID for the internal 7425 PHY and set the
PHY_IS_INTERNAL flag, otherwise consumers of this PHY driver would not
be able to properly identify it as such.
Fixes: d068b02cfdfc2 ("net: phy: add BCM7425 and BCM7429 PHYs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Petri Gynther <pgynther@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM7439 has an alternate PHY OUI: 0xae025080 which is to be found in
some variants of this chip.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
GPHY revision G0 has its version rolled over to 0x10, introduce an
explicit check for that revision and invoke the proper workaround
function for it.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY revisions E0 and F0 share the same shorter workaround initialization
sequence. Dedicate a special function for these two PHY revisions to
perform the needed workaround sequence.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHY revision D0 requires a specific workaround sequence which needs to
be applied to get the HW to behave properly in all corner cases
conditions. Do this based on the revision we just read out of the HW
using a specific function.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function performs a R/RC calibration reset and will start being
used by more than one function in the next patches, create a helper
function to factor code.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcm7445_config_init() was working around non-production version of the
PHY HW block, so just remove it entirely.
bcm7xxx_28nm_afe_config_init() was running for all PHY revisions greater
than B0, but this workaround sequence is really specific to the B0 PHY
revision, so rename the function accordingly and update the GPHY macro
to use the generic config_init callback.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bcm7xxx_28nm_config_init() can be called as frequently as needed by the
PHY library upon suspend/resume cycles and interface bring up/down, just
print the PHY revision once and for all in order not to spam kernel
logs.
Fixes: d8ebfed3f11b ("net: phy: bcm7xxx: utilize PHY revision in config_init")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Replace module init/exit which only calls phy_drivers_register with
module_phy_driver macro.
Tested using Micrel driver, and otherwise compile-tested only.
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Petri Gynther <pgynther@google.com>
Acked-by: Florian Fainelli <f.fainelli@gmai.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the GENET and SF2 drivers have been updated to communicate us
what is the revision of the BCM7xxx integrated PHY, utilize that
information in the config_init() callback to call into the appropriate
workaround function based on our revision.
While at it, we also print the revision and patch level to help debug
new chips.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no need for the PHY driver to check PHY_BRCM_100MBPS_WAR since
that is redundant with checking the PHY device supported features. Get
rid of that workaround flag.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|