| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
For RX channels we issue a stop command more than once if necessary
to allow it to stop. It turns out that TX channels could also
require retries.
Retry channel stop commands if necessary regardless of the channel
direction. Rename the symbol defining the retry count so it's not
RX-specific.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If a GSI stop channel command leaves the channel in STOP_IN_PROC
state, we retry the stop command after a 1-2 millisecond delay.
I have been told that a 3-5 millisecond delay is a better choice.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The GSI command timeout is currently 5 seconds, which is much higher
than it should be.
Express the timeout in milliseconds rather than seconds, and reduce
it to 50 milliseconds.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
65;6003;1c
The use of msleep() for small periods (less than 20 milliseconds) is
not recommended because the actual delay can be much different than
expected.
We use msleep(1) in several places in the IPA driver to insert short
delays. Replace them with usleep_range calls, which should reliably
delay a period in the range requested.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Create a new function gsi_irq_ev_ctrl_enable() that encapsulates
enabling the event ring control GSI interrupt type, and enables a
single event ring to signal that interrupt. When an event ring
changes state as a result of an event ring command, it triggers this
interrupt.
Create an inverse function gsi_irq_ev_ctrl_disable() as well.
Because only one event ring at a time is enabled for this interrupt,
we can simply disable the interrupt for *all* channels.
Create a pair of helpers that serve the same purpose for channel
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The return value of gsi_command() is true if successful or false if
we time out waiting for a completion interrupt.
Rename the variables in the three callers of gsi_command() to be
"timeout", to make it more obvious that's the only reason for
failure.
In addition, add a "gsi_" prefix to evt_ring_command() so its name
is consistent with the convention used for GSI channel and generic
commands.
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Saeed Mahameed <saeedm@nvidia.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IPA driver depends on some SMEM functionality (qcom_smem_init(),
qcom_smem_alloc(), and qcom_smem_virt_to_phys()), but this is not
reflected in the configuration dependencies. Add a dependency on
QCOM_SMEM to avoid attempts to build the IPA driver without SMEM.
This avoids a link error for certain configurations.
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Fixes: 38a4066f593c5 ("net: ipa: support COMPILE_TEST")
Signed-off-by: Alex Elder <elder@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org> # build-tested
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20210112192134.493-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Arrange for the IPA driver to be built when COMPILE_TEST is enabled.
Update the help text to reflect that we support two Qualcomm SoCs.
Suggested-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The second argument to gsi_trans_page_add() is a page pointer.
That declaration is found in header files used by "gsi_trans.h" for
(at least) arm64 and x86 builds, but apparently not for alpha
builds.
Fix this by adding a declaration of struct page to the top of
"gsi_trans.h".
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
At the moment it is quite hard to identify the network interface
provided by IPA in userspace components: The network interface is
created as virtual device, without any link to the IPA device.
The interface name ("rmnet_ipa%d") is the only indication that the
network interface belongs to IPA, but this is not very reliable.
Add SET_NETDEV_DEV() to associate the network interface with the
IPA parent device. This allows userspace services like ModemManager
to properly identify that this network interface is provided by IPA
and belongs to the modem.
Cc: Alex Elder <elder@kernel.org>
Fixes: a646d6ec9098 ("soc: qcom: ipa: modem and microcontroller")
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Link: https://lore.kernel.org/r/20210106100755.56800-1-stephan@gerhold.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Callers of evt_ring_command() no longer care whether the command
times out, and don't use what evt_ring_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 428b448ee764a ("net: ipa: use state to determine event ring command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Callers of gsi_channel_command() no longer care whether the command
times out, and don't use what gsi_channel_command() returns. Redefine
that function to have void return type.
Reported-by: kernel test robot <lkp@intel.com>
Fixes: 6ffddf3b3d182 ("net: ipa: use state to determine channel command success")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This patch implements the same basic fix for event rings as the
previous one does for channels.
The result of issuing an event ring control command should be that
the event ring changes state. If enabled, a completion interrupt
signals that the event ring state has changed. This interrupt is
enabled by gsi_evt_ring_command() and disabled again after the
command has completed (or we time out).
There is a window of time during which the command could complete
successfully without interrupting. This would cause the event ring
to transition to the desired new state.
So whether a event ring command ends via completion interrupt or
timeout, we can consider the command successful if the event ring
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The result of issuing a channel control command should be that the
channel changes state. If enabled, a completion interrupt signals
that the channel state has changed. This interrupt is enabled by
gsi_channel_command() and disabled again after the command has
completed (or we time out).
There is a window of time--after the completion interrupt is disabled
but before the channel state is read--during which the command could
complete successfully without interrupting. This would cause the
channel to transition to the desired new state.
So whether a channel command ends via completion interrupt or
timeout, we can consider the command successful if the channel
has entered the desired state (and a failure if it has not,
regardless of the cause).
Fixes: d6c9e3f506ae8 ("net: ipa: only enable generic command completion IRQ when needed");
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
We enable the completion interrupt for channel or event ring
commands only when we issue them. The interrupt is disabled after
the interrupt has fired, or after we have timed out waiting for it.
If we time out, the command could complete after the interrupt has
been disabled, causing a state change in the channel or event ring.
The interrupt associated with that state change would be delivered
the next time the completion interrupt is enabled.
To avoid previous command completions interfering with new commands,
clear all pending completion interrupts before re-enabling them for
a new command.
Fixes: b4175f8731f78 ("net: ipa: only enable GSI event control IRQs when needed")
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the core clock rate and interconnect bandwidth specifications
were moved into configuration data, a copy/paste bug was introduced,
causing the memory interconnect bandwidth to be set three times
rather than enabling the three different interconnects.
Fix this bug.
Fixes: 91d02f9551501 ("net: ipa: use config data for clocking")
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Georgi Djakov <georgi.djakov@linaro.org>
Link: https://lore.kernel.org/r/20201222151613.5730-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
xdp_return_frame_bulk() needs to pass a xdp_buff
to __xdp_return().
strlcpy got converted to strscpy but here it makes no
functional difference, so just keep the right code.
Conflicts:
net/netfilter/nf_tables_api.c
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Replace a comma between expression statements by a semicolon.
Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the coherent memory is freed in gsi_trans_pool_exit_dma(), we
are mistakenly passing the size of a single element in the pool
rather than the actual allocated size. Fix this bug.
Fixes: 9dd441e4ed575 ("soc: qcom: ipa: GSI transactions")
Reported-by: Stephen Boyd <swboyd@chromium.org>
Tested-by: Sujit Kautkar <sujitka@chromium.org>
Signed-off-by: Alex Elder <elder@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Link: https://lore.kernel.org/r/20201203215106.17450-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Jon Hunter reported observing a build bug in the IPA driver:
https://lore.kernel.org/netdev/5b5d9d40-94d5-5dad-b861-fd9bef8260e2@nvidia.com
The problem is that the QMB0 max read value set for IPA v4.5 (16) is
too large to fit in the 4-bit field.
The actual value we want is 0, which requests that the hardware use
the maximum it is capable of.
Reported-by: Jon Hunter <jonathanh@nvidia.com>
Tested-by: Jon Hunter <jonathanh@nvidia.com>
Signed-off-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201202141502.21265-1-elder@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Extend ipa_reg_init_hol_block_timer_val() so it properly calculates
the head-of-line block timeout to use for IPA v4.5.
Introduce hol_block_timer_qtime_val() to compute the value to use
for IPA v4.5, where Qtime is used as the basis of the timer. Call
that function from hol_block_timer_val() for IPA v4.5.
Both of these are private functions, so shorten their names a bit so
they don't take up so much space on the line.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Change aggr_time_limit_encoded() to properly calculate the
aggregation time limit to use for IPA v4.5.
Older IPA versions program the AGGR_GRANULARITY field of the
of the COUNTER_CFG register to set the granularity of the
aggregation timer, which we configure to be 500 microseconds.
Instead, IPA v4.5 selects between two possible granularity values
derived from the 19.2 MHz Qtime clock. These granularities are
100 microseconds or 1 millisecond per tick. We use the smaller
granularity if possible, unless the desired period is too large
to be specified that way.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.5 introduces a new unified timer architecture driven on the
19.2 MHz SoC crystal oscillator (XO). It is independent of the IPA
core clock and avoids some duplication.
Lower-resolution time stamps are derived from this by using only the
high-order bits of the 19.2 MHz Qtime clock. And timers are derived
from this based on "pulse generators" configured to fire at a fixed
rate based on the Qtime clock.
This patch introduces ipa_qtime_config(), which configures the Qtime
mechanism for use. It also adds to the IPA register definitions
related to timers and time stamping.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.5 significantly changes the format of the configuration
register used for endpoint aggregation. The AGGR_BYTE_LIMIT field
is now larger, and the positions of other fields are shifted. This
complicates the way we have to access this register because functions
like u32_encode_bits() require their field mask argument to be constant.
A further complication is that we want to know the maximum value
representable by at least one of these fields, and that too requires
a constant field mask.
This patch adds support for IPA v4.5 endpoint aggregation registers
in a way that continues to support "legacy" IPA hardware. It does
so in a way that keeps field masks constant.
First, for each variable field mask, we define an inline function
whose return value is either the legacy value or the IPA v4.5 value.
Second, we define functions for these fields that encode a value
to use in each field based on the IPA version (this approach is
already used elsewhere). The field mask provided is supplied by
the function mentioned above.
Finally, for the aggregation byte limit fields where we want to
know the maximum representable value, we define a function that
returns that maximum, computed from the appropriate field mask.
We can no longer verify at build time that our buffer size is
in the range that can be represented by the aggregation byte
limit field. So remove the test done by a BUILD_BUG_ON() call
in ipa_endpoint_validate_build(), and implement a comparable check
at the top of ipa_endpoint_data_valid().
Doing that makes ipa_endpoint_validate_build() contain a single
line BUILD_BUG_ON() call, so just remove that function and move
the remaining line into ipa_endpoint_data_valid().
One final note: the aggregation time limit value for IPA v4.5 needs
to be computed differently. That is handled in an upcoming patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The offsets for almost all GSI registers we use have different
offsets starting at IPA version 4.5. Only two registers remain
in their original location.
In a way though, the new register locations are not *that*
different. The entire group of affected registers has simply
been shifted down in memory by a fixed amount (0xd000). So for
example, the channel context 0 register that has a base offset of
0x0001c000 for "older" hardware now has a base offset of 0x0000f000.
This patch aims to add support for IPA v4.5 registers at their new
offets in a way that minimizes the amount of code that needs to
change. It is not ideal, but it avoids the need to maintain
a nearly complete set of additional register offset definitions.
The approach takes advantage of the fact that when accessing GSI
registers we do not access any of memory at lower end of the "gsi"
memory range (with two exceptions already noted). In particular,
we do not access anything within the bottom 0xd000 bytes of the
GSI memory range.
For IPA version 4.5, after we map the GSI memory, we adjust the
virtual memory pointer downward by the fixed amount (0xd000).
That way, register accesses using the offsets defined by the
existing GSI_REG_*() macros will resolve to the proper locations
for IPA version 4.5.
The two registers *not* affected by this offset are accessed only
in gsi_irq_setup(). There, for IPA version 4.5, we undo the general
register adjustment by adding the fixed amount back to the virtual
address to access these registers.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Very few GSI register definitions change for IPA v4.5, however
as a group their position in memory shifts a constant amount
(handled by the next commit).
Add definitions and update comments to the set of GSI registers to
support changes that come with IPA v4.5.
Update the logic in gsi_channel_program() to accommodate the new
(expanded) PREFETCH_MODE field in the CH_C_QOS register.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update the IPA code to make use of the updated IPA v4.5 register
definitions. Generally what this patch does is, if IPA v4.5
hardware is in use:
- Ensure new registers or fields in IPA v4.5 are updated where
required
- Ensure registers or fields not supported in IPA v4.5 are not
examined when read, or are set to 0 when written
It does this while preserving the existing functionality for IPA
versions lower than v4.5.
The values to program for QSB_MAX_READS and QSB_MAX_WRITES and the
source and destination resource counts are updated to be correct for
all versions through v4.5 as well.
Note that IPA_RESOURCE_GROUP_SRC_MAX and IPA_RESOURCE_GROUP_DST_MAX
already reflect that 5 is an acceptable number of resources (which
IPA v4.5 implements).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.5 adds a few fields to the endpoint header and extended
header configuration registers that represent new high-order bits
for certain offsets and sizes. Add code to incorporate these upper
bits into the registers for IPA v4.5.
This includes creating ipa_header_size_encoded(), which handles
encoding the metadata offset field for use in the ENDP_INIT_HDR
register in a way appropriate for the hardware version. This and
ipa_metadata_offset_encoded() ensure the mask argument passed to
u32_encode_bits() is constant.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Update "ipa_reg.h" so that register definitions support IPA hardware
version 4.5, in addition to versions 3.5.1 through v4.2. Most of
the register definitions are the same, but in some cases fields are
added, changed, or eliminated.
Updates for a few IPA v4.5 registers are more complex, and adding
those definition will be deferred to separate patches. This patch
only updates the register offset and field definitions, and adds
informational comments.
The only code change avoids accessing the backward compatibility
register for IPA version 4.5 in ipa_hardware_config(). Other IPA
v4.5-specific code changes will come later.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Starting with IPA v4.2 there is a GSI channel option to use an
"escape buffer" instead of prefetch buffers. This should be used
for all channels *except* the AP command TX channel. The logic
that implements this has it backwards; fix this bug.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
These are only used as input arguments to qmi_handle_init() which
accepts const pointers to both qmi_ops and qmi_msg_handler. Make them
const to allow the compiler to put them in read-only memory.
Signed-off-by: Rikard Falkeborn <rikard.falkeborn@gmail.com>
Acked-by: Alex Elder <elder@linaro.org>
Link: https://lore.kernel.org/r/20201122234031.33432-2-rikard.falkeborn@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
A system shutdown can happen at essentially any time, and it's
possible that the IPA driver is busy when a shutdown is underway.
IPA hardware accesses IMEM and SMEM memory regions using an IOMMU,
and at some point during shutdown, needed I/O mappings could become
invalid. This could be disastrous for any "in flight" IPA activity.
Avoid this by defining a new driver shutdown callback that stops all
IPA activity and cleanly shuts down the driver. It merely calls the
driver's existing remove callback, reporting the error if it returns
one.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The IPA driver remove callback, ipa_remove(), calls ipa_modem_stop()
if the setup stage of initialization is complete. If a concurrent
call to ipa_modem_start() or ipa_modem_stop() has begin but not
completed, ipa_modem_stop() can return an error (-EBUSY).
The next patch adds a driver shutdown callback, which will simply
call ipa_remove(). We really want our shutdown callback to clean
things up. So add a single retry to the ipa_modem_stop() call in
ipa_remove() after a short (millisecond) delay. This offers no
guarantee the shutdown will complete successfully, but we'll at
least try a little harder before giving up.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When stopping an AP RX channel, there can be a transient period
while the channel enters STOP_IN_PROC state before reaching the
final STOPPED state. In that case we make another attempt to stop
the channel.
Similarly, when stopping a modem channel (using a GSI generic
command issued from the AP), it's possible that multiple attempts
will be required before the channel reaches STOPPED state.
Add a field to the GSI structure to record an errno representing the
result code provided when a generic command completes. If the
result learned in gsi_isr_gp_int1() is RETRY, record -EAGAIN in the
result code, otherwise record 0 for success, or -EIO for any other
result.
If we time out nf gsi_generic_command() waiting for the command to
complete, return -ETIMEDOUT (as before). Otherwise return the
result stashed by gsi_isr_gp_int1().
Add a loop in gsi_modem_channel_halt() to reissue the HALT command
if the result code indicates -EAGAIN. Limit this to 10 retries
(after the initial attempt).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
IPA v4.2 has a hardware quirk that requires the AP to allocate GSI
channels for the modem to use. It is recommended that these modem
channels get stopped (with a HALT generic command) by the AP when
its IPA driver gets removed.
The AP has no way of knowing the current state of a modem channel.
So when the IPA driver issues a HALT command it's possible the
channel is not running, and in that case we get an error indication.
This error simply means we didn't need to stop the channel, so we
can ignore it.
This patch adds an explanation for this situation, and arranges for
this condition to *not* report an error message.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If the rmnet_ipa0 network device has not been opened at the time
we remove or shut down the IPA driver, its underlying TX and RX
GSI channels will not have been started, and they will still be
in ALLOCATED state.
The RESET command on a channel is meant to return a channel to
ALLOCATED state after it's been stopped. But if it was never
started, its state will still be ALLOCATED, the RESET command
is not required.
Quietly skip doing the reset without printing an error message if a
channel is already in ALLOCATED state when we request it be reset.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When a GSI command is used to change the state of a channel or event
ring we check the state before and after the command to ensure it is
as expected. If not, we print an error message, but it does not
include the channel or event ring id, and it easily can. Add the
channel or event ring id to these error messages.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Stop assuming a fixed IPA core clock rate and interconnect
bandwidths. Use the configuration data defined for these
things instead. Get rid of the previously-used constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Populate the core clock rate and interconnect average and peak
bandwidth data for SDM845 and SC7180 in their configuration data
files. At this point we still don't *use* this data.
Note that SC7180 actually defines a new core clock rate (100 MHz
instead of 75 MHz) and new interconnect bandwidth values. They
will be activated in the next commit, which uses the configured
values rather than the fixed constants.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define a new type of configuration data, used to initialize the
IPA core clock and interconnects. This is the first of three
patches, and defines the data types and interface but doesn't
yet use them.
Switch the return value if there is no matching configuration data
to ENODEV instead of ENOTSUPP (to avoid using the nonstandard errno).
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Some last cleanups for the existing IPA register definitions:
- Remove the definition of IPA_REG_ENABLED_PIPES_OFFSET, because
it is not used.
- Use "IPA_" instead of "BAM_" as the prefix on fields associated
with the FLAVOR_0 register. We use GSI (not BAM), but the
fields apply to both GSI and BAM.
- Get rid of the definition of IPA_CS_RSVD; it is never used.
- Add two missing field mask definitions for the INIT_DEAGGR
endpoint register.
- Eliminate a few of the defined sequencer types, because they
are unused. We can add them back when needed.
- Add a field mask to indicate which bit causes an interrupt on
the microcontroller.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move the definition of the ipa_irq_id enumerated type out of
"ipa_interrupt.h" and into "ipa_reg.h", and flesh out its set of
defined values. Each interrupt id indicates a particular type of
IPA interrupt that can be signaled. Their numeric values define bit
positions in the IPA_IRQ_* registers, so should their definitions
should accompany the definition of those register offsets.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Move a few things around in "ipa_reg.h":
- Move the definition of ipa_reg_state_aggr_active_offset() down
a bit in the file so definitions are ordered by offset (for
the lowest supported IPA version) like all other definitions.
- Move the definition TIMER_FREQUENCY to be immediately above
the definition of ipa_aggr_granularity_val() where it's used.
- Move each register field value enumerated type definition to
immediately follow the definitions of the register and field
it is associated with.
No code functionality is modified by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Revise or add comments in "ipa_reg.h" for to provide more
information, and to improve clarity and consistency.
- Always provide a comment to define when a register or field is
supported (or not) for certain versions of IPA hardware.
- Try to be specific about *which* or *how many* definitions
a comment refers to.
- Move comments stating that ipa->available defines the valid
bits in various registers *above* the register offset
definition, to avoid some checkpatch.pl warnings.
No code is changed by this patch.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Consistently define numeric values for enumerated type members using
hexidecimal (rather than decimal) format values. Align the values
assigned in the same column in each file.
Only assign values where they really matter, for example don't
assign IPA_ENDPOINT_AP_MODEM_TX the value 0.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The backward compatibility register field masks are defined using
single-bit masks defined with BIT(x) rather than GENMASK(x, x).
Change this one set of definitions to follow the GENMASK() pattern
used everywhere else. Add a few missing field definitions for this
register as well.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Several IPA register field masks are defined without the "_FMASK"
suffix naming convention. Rename these, so all field masks are
consistently named.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Rename two suspend IRQ registers so they follow the IPA_REG_IRQ_xxx
naming convention used elsewhere.
Signed-off-by: Alex Elder <elder@linaro.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
