| Age | Commit message (Collapse) | Author | |
|---|---|---|---|
| 2021-01-15 | net: ks8851: remove definition of DEBUG | Tom Rix | |
| Defining DEBUG should only be done in development. So remove DEBUG. Signed-off-by: Tom Rix <trix@redhat.com> Reviewed-by: Marek Vasut <marex@denx.de> Link: https://lore.kernel.org/r/20210115153128.131026-1-trix@redhat.com Signed-off-by: Jakub Kicinski <kuba@kernel.org> | |||
| 2021-01-12 | net: ks8851: Select PHYLIB and MICREL_PHY in Kconfig | Marek Vasut | |
| The PHYLIB must be selected to provide mdiobus_*() functions, and the MICREL_PHY is necessary too, as that is the only possible PHY attached to the KS8851 (it is the internal PHY). Fixes: ef3631220d2b ("net: ks8851: Register MDIO bus and the internal PHY") Signed-off-by: Marek Vasut <marex@denx.de> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Lukas Wunner <lukas@wunner.de> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Link: https://lore.kernel.org/r/20210111125046.36326-1-marex@denx.de Signed-off-by: Jakub Kicinski <kuba@kernel.org> | |||
| 2021-01-05 | net: ks8851: Register MDIO bus and the internal PHY | Marek Vasut | |
| The KS8851 has a reduced internal PHY, which is accessible through its registers at offset 0xe4. The PHY is compatible with KS886x PHY present in Micrel switches, except the PHY ID Low/High registers are swapped. Register MDIO bus so this PHY can be detected and probed by phylib. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Heiner Kallweit <hkallweit1@gmail.com> Cc: Lukas Wunner <lukas@wunner.de> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-12-09 | net: micrel: convert comma to semicolon | Zheng Yongjun | |
| Replace a comma between expression statements by a semicolon. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-10-03 | net: ksz884x: Use fallthrough pseudo-keyword | Gustavo A. R. Silva | |
| Replace /* Fallthrough... */ comment with the new pseudo-keyword macro fallthrough[1]. [1] https://www.kernel.org/doc/html/v5.7/process/deprecated.html?highlight=fallthrough#implicit-switch-case-fall-through Signed-off-by: Gustavo A. R. Silva <gustavoars@kernel.org> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-09-25 | drivers/net/ethernet: clean up mis-targeted comments | Jesse Brandeburg | |
| As part of the W=1 cleanups for ethernet, a million [*] driver comments had to be cleaned up to get the W=1 compilation to succeed. This change finally makes the drivers/net/ethernet tree compile with W=1 set on the command line. NOTE: The kernel uses kdoc style (see Documentation/process/kernel-doc.rst) when documenting code, not doxygen or other styles. After this patch the x86_64 build has no warnings from W=1, however scripts/kernel-doc says there are 1545 more warnings in source files, that I need to develop a script to fix in a followup patch. The errors fixed here are all kdoc of a few classes, with a few outliers: In file included from drivers/net/ethernet/qlogic/netxen/netxen_nic_hw.c:10: drivers/net/ethernet/qlogic/netxen/netxen_nic.h:1193:18: warning: ‘FW_DUMP_LEVELS’ defined but not used [-Wunused-const-variable=] 1193 | static const u32 FW_DUMP_LEVELS[] = { 0x3, 0x7, 0xf, 0x1f, 0x3f, 0x7f, 0xff }; | ^~~~~~~~~~~~~~ ... repeats 4 times... drivers/net/ethernet/sun/cassini.c:2084:24: warning: suggest braces around empty body in an ‘else’ statement [-Wempty-body] 2084 | RX_USED_ADD(page, i); drivers/net/ethernet/natsemi/ns83820.c: In function ‘phy_intr’: drivers/net/ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] 603 | u32 tbisr, tanar, tanlpar; | ^~~~~ drivers/net/ethernet/natsemi/ns83820.c: In function ‘ns83820_get_link_ksettings’: drivers/net/ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] 1207 | u32 cfg, tanar, tbicr; | ^~~~~ drivers/net/ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] 1063 | int data_size, yf_size; | ^~~~~~~ Normal kdoc fixes: warning: Function parameter or member 'x' not described in 'y' warning: Excess function parameter 'x' description in 'y' warning: Cannot understand <string> on line <NNN> - I thought it was a doc line [*] - ok it wasn't quite a million, but it felt like it. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-09-25 | drivers/net/ethernet: clean up unused assignments | Jesse Brandeburg | |
| As part of the W=1 compliation series, these lines all created warnings about unused variables that were assigned a value. Most of them are from register reads, but some are just picking up a return value from a function and never doing anything with it. Fixed warnings: .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/brocade/bna/bnad.c:3280:6: warning: variable ‘rx_count’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:512:6: warning: variable ‘val’ set but not used [-Wunused-but-set-variable] .../ethernet/cortina/gemini.c:2110:21: warning: variable ‘config0’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1327:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/cavium/liquidio/octeon_device.c:1358:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/media.c:322:8: warning: variable ‘setup’ set but not used [-Wunused-but-set-variable] .../ethernet/dec/tulip/de4x5.c:4928:13: warning: variable ‘r3’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:1652:7: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6510:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/micrel/ksz884x.c:6087: warning: cannot understand function prototype: 'struct hw_regs ' .../ethernet/microchip/lan743x_main.c:161:6: warning: variable ‘int_en’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:1702:6: warning: variable ‘int_sts’ set but not used [-Wunused-but-set-variable] .../ethernet/microchip/lan743x_main.c:3041:6: warning: variable ‘ret’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:603:6: warning: variable ‘tbisr’ set but not used [-Wunused-but-set-variable] .../ethernet/natsemi/ns83820.c:1207:11: warning: variable ‘tanar’ set but not used [-Wunused-but-set-variable] .../ethernet/marvell/mvneta.c:754:6: warning: variable ‘dummy’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:33:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:160:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:490:6: warning: variable ‘val32’ set but not used [-Wunused-but-set-variable] .../ethernet/neterion/vxge/vxge-traffic.c:2378:6: warning: variable ‘val64’ set but not used [-Wunused-but-set-variable] .../ethernet/packetengines/yellowfin.c:1063:18: warning: variable ‘yf_size’ set but not used [-Wunused-but-set-variable] .../ethernet/realtek/8139cp.c:1242:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/mellanox/mlx4/en_tx.c:858:6: warning: variable ‘ring_cons’ set but not used [-Wunused-but-set-variable] .../ethernet/sis/sis900.c:792:6: warning: variable ‘status’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:878:11: warning: variable ‘rx_ev_pkt_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:23: warning: variable ‘rx_ev_mcast_pkt’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:877:7: warning: variable ‘rx_ev_hdr_type’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:876:7: warning: variable ‘rx_ev_other_err’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:1646:21: warning: variable ‘buftbl_min’ set but not used [-Wunused-but-set-variable] .../ethernet/sfc/falcon/farch.c:2535:32: warning: variable ‘spec’ set but not used [-Wunused-but-set-variable] .../ethernet/via/via-velocity.c:880:6: warning: variable ‘curr_status’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/tlan.c:656:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/davinci_emac.c:1230:6: warning: variable ‘num_tx_pkts’ set but not used [-Wunused-but-set-variable] .../ethernet/synopsys/dwc-xlgmac-common.c:516:8: warning: variable ‘str’ set but not used [-Wunused-but-set-variable] .../ethernet/ti/cpsw_new.c:1662:22: warning: variable ‘priv’ set but not used [-Wunused-but-set-variable] The register reads should be OK, because the current implementation of readl and friends will always execute even without an lvalue. When it makes sense, just remove the lvalue assignment and the local. Other times, just remove the offending code, and occasionally, just mark the variable as maybe unused since it could be used in an ifdef or debug scenario. Only compile tested with W=1. Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Acked-by: Edward Cree <ecree@solarflare.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-09-19 | net: micrel: Remove set but not used variable | Zheng Yongjun | |
| Fixes gcc '-Wunused-but-set-variable' warning: drivers/net/ethernet/micrel/ksz884x.c: In function rx_proc: drivers/net/ethernet/micrel/ksz884x.c:4981:6: warning: variable ‘rx_status’ set but not used [-Wunused-but-set-variable] drivers/net/ethernet/micrel/ksz884x.c: In function netdev_get_ethtool_stats: drivers/net/ethernet/micrel/ksz884x.c:6512:6: warning: variable ‘rc’ set but not used [-Wunused-but-set-variable] these variable is never used, so remove it. Signed-off-by: Zheng Yongjun <zhengyongjun3@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-09-14 | net: micrel: convert tasklets to use new tasklet_setup() API | Allen Pais | |
| In preparation for unconditionally passing the struct tasklet_struct pointer to all tasklet callbacks, switch to using the new tasklet_setup() and from_tasklet() to pass the tasklet pointer explicitly. Signed-off-by: Romain Perier <romain.perier@gmail.com> Signed-off-by: Allen Pais <apais@linux.microsoft.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-07-14 | ksz884x: switch from 'pci_' to 'dma_' API | Christophe JAILLET | |
| The wrappers in include/linux/pci-dma-compat.h should go away. The patch has been generated with the coccinelle script below and has been hand modified to replace GFP_ with a correct flag. It has been compile tested. When memory is allocated in 'ksz_alloc_desc()', GFP_KERNEL can be used because a few lines below, GFP_KERNEL is also used in the 'ksz_alloc_soft_desc()' calls. @@ @@ - PCI_DMA_BIDIRECTIONAL + DMA_BIDIRECTIONAL @@ @@ - PCI_DMA_TODEVICE + DMA_TO_DEVICE @@ @@ - PCI_DMA_FROMDEVICE + DMA_FROM_DEVICE @@ @@ - PCI_DMA_NONE + DMA_NONE @@ expression e1, e2, e3; @@ - pci_alloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3; @@ - pci_zalloc_consistent(e1, e2, e3) + dma_alloc_coherent(&e1->dev, e2, e3, GFP_) @@ expression e1, e2, e3, e4; @@ - pci_free_consistent(e1, e2, e3, e4) + dma_free_coherent(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_single(e1, e2, e3, e4) + dma_map_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_single(e1, e2, e3, e4) + dma_unmap_single(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4, e5; @@ - pci_map_page(e1, e2, e3, e4, e5) + dma_map_page(&e1->dev, e2, e3, e4, e5) @@ expression e1, e2, e3, e4; @@ - pci_unmap_page(e1, e2, e3, e4) + dma_unmap_page(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_map_sg(e1, e2, e3, e4) + dma_map_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_unmap_sg(e1, e2, e3, e4) + dma_unmap_sg(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_cpu(e1, e2, e3, e4) + dma_sync_single_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_single_for_device(e1, e2, e3, e4) + dma_sync_single_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_cpu(e1, e2, e3, e4) + dma_sync_sg_for_cpu(&e1->dev, e2, e3, e4) @@ expression e1, e2, e3, e4; @@ - pci_dma_sync_sg_for_device(e1, e2, e3, e4) + dma_sync_sg_for_device(&e1->dev, e2, e3, e4) @@ expression e1, e2; @@ - pci_dma_mapping_error(e1, e2) + dma_mapping_error(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_dma_mask(e1, e2) + dma_set_mask(&e1->dev, e2) @@ expression e1, e2; @@ - pci_set_consistent_dma_mask(e1, e2) + dma_set_coherent_mask(&e1->dev, e2) Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-07-02 | ksz884x: mark pcidev_suspend() as __maybe_unused | Wei Yongjun | |
| In certain configurations without power management support, gcc report the following warning: drivers/net/ethernet/micrel/ksz884x.c:7182:12: warning: 'pcidev_suspend' defined but not used [-Wunused-function] 7182 | static int pcidev_suspend(struct device *dev_d) | ^~~~~~~~~~~~~~ Mark pcidev_suspend() as __maybe_unused to make it clear. Fixes: 64120615d140 ("ksz884x: use generic power management") Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-07-01 | ksz884x: use generic power management | Vaibhav Gupta | |
| With legacy PM, drivers themselves were responsible for managing the device's power states and takes care of register states. After upgrading to the generic structure, PCI core will take care of required tasks and drivers should do only device-specific operations. Thus, there is no need to call the PCI helper functions like pci_enable_wake(), pci_save/restore_sate() and pci_set_power_state(). Compile-tested only. Signed-off-by: Vaibhav Gupta <vaibhavgupta40@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-06-14 | treewide: replace '---help---' in Kconfig files with 'help' | Masahiro Yamada | |
| Since commit 84af7a6194e4 ("checkpatch: kconfig: prefer 'help' over '---help---'"), the number of '---help---' has been gradually decreasing, but there are still more than 2400 instances. This commit finishes the conversion. While I touched the lines, I also fixed the indentation. There are a variety of indentation styles found. a) 4 spaces + '---help---' b) 7 spaces + '---help---' c) 8 spaces + '---help---' d) 1 space + 1 tab + '---help---' e) 1 tab + '---help---' (correct indentation) f) 1 tab + 1 space + '---help---' g) 1 tab + 2 spaces + '---help---' In order to convert all of them to 1 tab + 'help', I ran the following commend: $ find . -name 'Kconfig*' | xargs sed -i 's/^[[:space:]]*---help---/\thelp/' Signed-off-by: Masahiro Yamada <masahiroy@kernel.org> | |||
| 2020-05-28 | net: ks8851: Remove ks8851_mll.c | Marek Vasut | |
| The ks8851_mll.c is replaced by ks8851_par.c, which is using common code from ks8851.c, just like ks8851_spi.c . Remove this old ad-hoc driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Implement Parallel bus operations | Marek Vasut | |
| Implement accessors for KS8851-16MLL/MLLI/MLLU parallel bus variant of the KS8851. This is based off the ks8851_mll.c , which is a driver for exactly the same hardware, however the ks8851.c code is much higher quality. Hence, this patch pulls out the relevant information from the ks8851_mll.c on how to access the bus, but uses the common ks8851.c code. To make this patch reviewable, instead of rewriting ks8851_mll.c, ks8851_mll.c is removed in a separate subsequent patch. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Separate SPI operations into separate file | Marek Vasut | |
| Pull all the SPI bus specific code into a separate file, so that it is not mixed with the common code. Rename ks8851.c to ks8851_common.c. The ks8851_common.c is linked with ks8851_spi.c now, so it can call the accessors in the ks8851_spi.c without any pointer indirection. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Implement register, FIFO, lock accessor callbacks | Marek Vasut | |
| The register and FIFO accessors are bus specific, so is locking. Implement callbacks so that each variant of the KS8851 can implement matching accessors and locking, and use the rest of the common code. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Permit overridding interrupt enable register | Marek Vasut | |
| The parallel bus variant does not need to use the TX interrupt at all as it writes the TX FIFO directly with in .ndo_start_xmit, permit the drivers to configure the interrupt enable bits. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Factor out TX work flush function | Marek Vasut | |
| While the SPI version of the KS8851 requires a TX worker thread to pump data via SPI, the parallel bus version can write data into the TX FIFO directly in .ndo_start_xmit, as the parallel bus access is much faster and does not sleep. Factor out this TX work flush part, so it can be overridden by the parallel bus driver. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Split out SPI specific code from probe() and remove() | Marek Vasut | |
| Factor out common code into ks8851_probe_common() and ks8851_remove_common() to permit both SPI and parallel bus driver variants to use the common code path for both probing and removal. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Split out SPI specific entries in struct ks8851_net | Marek Vasut | |
| Add a new struct ks8851_net_spi, which embeds the original struct ks8851_net and contains the entries specific only to the SPI variant of KS8851. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Factor out SKB receive function | Marek Vasut | |
| Factor out this netif_rx_ni(), so it could be overridden by the parallel bus variant of the KS8851 driver. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Factor out bus lock handling | Marek Vasut | |
| Pull out bus access locking code into separate functions, this is done in preparation for unifying the driver with the parallel bus one. The parallel bus driver does not need heavy mutex locking of the bus and works better with spinlocks, hence prepare these locking functions to be overridden then. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Use 16-bit read of RXFC register | Marek Vasut | |
| The RXFC register is the only one being read using 8-bit accessors. To make it easier to support the 16-bit accesses used by the parallel bus variant of KS8851, use 16-bit accessor to read RXFC register as well as neighboring RXFCTR register. Remove ks8851_rdreg8() as it is not used anywhere anymore. There should be no functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Use 16-bit writes to program MAC address | Marek Vasut | |
| On the SPI variant of KS8851, the MAC address can be programmed with either 8/16/32-bit writes. To make it easier to support the 16-bit parallel option of KS8851 too, switch both the MAC address programming and readout to 16-bit operations. Remove ks8851_wrreg8() as it is not used anywhere anymore. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Remove ks8851_rdreg32() | Marek Vasut | |
| The ks8851_rdreg32() is used only in one place, to read two registers using a single read. To make it easier to support 16-bit accesses via parallel bus later on, replace this single read with two 16-bit reads from each of the registers and drop the ks8851_rdreg32() altogether. If this has noticeable performance impact on the SPI variant of KS8851, then we should consider using regmap to abstract the SPI and parallel bus options and in case of SPI, permit regmap to merge register reads of neighboring registers into single, longer, read. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Use dev_{get,set}_drvdata() | Marek Vasut | |
| Replace spi_{get,set}_drvdata() with dev_{get,set}_drvdata(), which works for both SPI and platform drivers. This is done in preparation for unifying the KS8851 SPI and parallel bus drivers. There should be no functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Use devm_alloc_etherdev() | Marek Vasut | |
| Use device managed version of alloc_etherdev() to simplify the code. No functional change intended. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Pass device node into ks8851_init_mac() | Marek Vasut | |
| Since the driver probe function already has a struct device *dev pointer and can easily derive of_node pointer from it, pass the of_node pointer as a parameter to ks8851_init_mac() to avoid fishing it out from ks->spidev. This is the only reference to spidev in the function, so get rid of it. This is done in preparation for unifying the KS8851 SPI and parallel bus drivers. No functional change. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Replace dev_err() with netdev_err() in IRQ handler | Marek Vasut | |
| Use netdev_err() instead of dev_err() to avoid accessing the spidev->dev in the interrupt handler. This is the only place which uses the spidev in this function, so replace it with netdev_err() to get rid of it. This is done in preparation for unifying the KS8851 SPI and parallel drivers. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Rename ndev to netdev in probe | Marek Vasut | |
| Rename ndev variable to netdev for the sake of consistency. No functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-05-28 | net: ks8851: Factor out spi->dev in probe()/remove() | Marek Vasut | |
| Pull out the spi->dev into one common place in the function instead of having it repeated over and over again. This is done in preparation for unifying ks8851 and ks8851-mll drivers. No functional change. Reviewed-by: Andrew Lunn <andrew@lunn.ch> Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-03-29 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net | David S. Miller | |
| Minor comment conflict in mac80211. Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-03-26 | net: ks8851-ml: Fix IO operations, again | Marek Vasut | |
| This patch reverts 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") and edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access"), because it turns out these were only necessary due to buggy hardware. This patch adds a check for such a buggy hardware to prevent any such mistakes again. While working further on the KS8851 driver, it came to light that the KS8851-16MLL is capable of switching bus endianness by a hardware strap, EESK pin. If this strap is incorrect, the IO accesses require such endian swapping as is being reverted by this patch. Such swapping also impacts the performance significantly. Hence, in addition to removing it, detect that the hardware is broken, report to user, and fail to bind with such hardware. Fixes: 58292104832f ("net: ks8851-ml: Fix 16-bit IO operation") Fixes: edacb098ea9c ("net: ks8851-ml: Fix 16-bit data access") Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-27 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net | David S. Miller | |
| The mptcp conflict was overlapping additions. The SMC conflict was an additional and removal happening at the same time. Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-23 | net: ks8851-ml: Fix IRQ handling and locking | Marek Vasut | |
| The KS8851 requires that packet RX and TX are mutually exclusive. Currently, the driver hopes to achieve this by disabling interrupt from the card by writing the card registers and by disabling the interrupt on the interrupt controller. This however is racy on SMP. Replace this approach by expanding the spinlock used around the ks_start_xmit() TX path to ks_irq() RX path to assure true mutual exclusion and remove the interrupt enabling/disabling, which is now not needed anymore. Furthermore, disable interrupts also in ks_net_stop(), which was missing before. Note that a massive improvement here would be to re-use the KS8851 driver approach, which is to move the TX path into a worker thread, interrupt handling to threaded interrupt, and synchronize everything with mutexes, but that would be a much bigger rework, for a separate patch. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-21 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net | David S. Miller | |
| Conflict resolution of ice_virtchnl_pf.c based upon work by Stephen Rothwell. Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-20 | net: use netif_is_bridge_port() to check for IFF_BRIDGE_PORT | Julian Wiedmann | |
| Trivial cleanup, so that all bridge port-specific code can be found in one go. CC: Johannes Berg <johannes@sipsolutions.net> CC: Roopa Prabhu <roopa@cumulusnetworks.com> CC: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: Julian Wiedmann <jwi@linux.ibm.com> Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-16 | net: ks8851-ml: Fix 16-bit IO operation | Marek Vasut | |
| The Micrel KSZ8851-16MLLI datasheet DS00002357B page 12 states that BE[3:0] signals are active high. This contradicts the measurements of the behavior of the actual chip, where these signals behave as active low. For example, to read the CIDER register, the bus must expose 0xc0c0 during the address phase, which means BE[3:0]=4'b1100. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-16 | net: ks8851-ml: Fix 16-bit data access | Marek Vasut | |
| The packet data written to and read from Micrel KSZ8851-16MLLI must be byte-swapped in 16-bit mode, add this byte-swapping. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2020-02-16 | net: ks8851-ml: Remove 8-bit bus accessors | Marek Vasut | |
| This driver is mixing 8-bit and 16-bit bus accessors for reasons unknown, however the speculation is that this was some sort of attempt to support the 8-bit bus mode. As per the KS8851-16MLL documentation, all two registers accessed via the 8-bit accessors are internally 16-bit registers, so reading them using 16-bit accessors is fine. The KS_CCR read can be converted to 16-bit read outright, as it is already a concatenation of two 8-bit reads of that register. The KS_RXQCR accesses are 8-bit only, however writing the top 8 bits of the register is OK as well, since the driver caches the entire 16-bit register value anyway. Finally, the driver is not used by any hardware in the kernel right now. The only hardware available to me is one with 16-bit bus, so I have no way to test the 8-bit bus mode, however it is unlikely this ever really worked anyway. If the 8-bit bus mode is ever required, it can be easily added by adjusting the 16-bit accessors to do 2 consecutive accesses, which is how this should have been done from the beginning. Signed-off-by: Marek Vasut <marex@denx.de> Cc: David S. Miller <davem@davemloft.net> Cc: Lukas Wunner <lukas@wunner.de> Cc: Petr Stetiar <ynezz@true.cz> Cc: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2019-12-12 | netdev: pass the stuck queue to the timeout handler | Michael S. Tsirkin | |
| This allows incrementing the correct timeout statistic without any mess. Down the road, devices can learn to reset just the specific queue. The patch was generated with the following script: use strict; use warnings; our $^I = '.bak'; my @work = ( ["arch/m68k/emu/nfeth.c", "nfeth_tx_timeout"], ["arch/um/drivers/net_kern.c", "uml_net_tx_timeout"], ["arch/um/drivers/vector_kern.c", "vector_net_tx_timeout"], ["arch/xtensa/platforms/iss/network.c", "iss_net_tx_timeout"], ["drivers/char/pcmcia/synclink_cs.c", "hdlcdev_tx_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/infiniband/ulp/ipoib/ipoib_main.c", "ipoib_timeout"], ["drivers/message/fusion/mptlan.c", "mpt_lan_tx_timeout"], ["drivers/misc/sgi-xp/xpnet.c", "xpnet_dev_tx_timeout"], ["drivers/net/appletalk/cops.c", "cops_timeout"], ["drivers/net/arcnet/arcdevice.h", "arcnet_timeout"], ["drivers/net/arcnet/arcnet.c", "arcnet_timeout"], ["drivers/net/arcnet/com20020.c", "arcnet_timeout"], ["drivers/net/ethernet/3com/3c509.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c515.c", "corkscrew_timeout"], ["drivers/net/ethernet/3com/3c574_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c589_cs.c", "el3_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/3c59x.c", "vortex_tx_timeout"], ["drivers/net/ethernet/3com/typhoon.c", "typhoon_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390.h", "eip_tx_timeout"], ["drivers/net/ethernet/8390/8390.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/8390p.c", "eip_tx_timeout"], ["drivers/net/ethernet/8390/ax88796.c", "ax_ei_tx_timeout"], ["drivers/net/ethernet/8390/axnet_cs.c", "axnet_tx_timeout"], ["drivers/net/ethernet/8390/etherh.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/hydra.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mac8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/mcf8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/lib8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/8390/ne2k-pci.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/pcnet_cs.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/smc-ultra.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/wd.c", "ei_tx_timeout"], ["drivers/net/ethernet/8390/zorro8390.c", "__ei_tx_timeout"], ["drivers/net/ethernet/adaptec/starfire.c", "tx_timeout"], ["drivers/net/ethernet/agere/et131x.c", "et131x_tx_timeout"], ["drivers/net/ethernet/allwinner/sun4i-emac.c", "emac_timeout"], ["drivers/net/ethernet/alteon/acenic.c", "ace_watchdog"], ["drivers/net/ethernet/amazon/ena/ena_netdev.c", "ena_tx_timeout"], ["drivers/net/ethernet/amd/7990.h", "lance_tx_timeout"], ["drivers/net/ethernet/amd/7990.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/a2065.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/am79c961a.c", "am79c961_timeout"], ["drivers/net/ethernet/amd/amd8111e.c", "amd8111e_tx_timeout"], ["drivers/net/ethernet/amd/ariadne.c", "ariadne_tx_timeout"], ["drivers/net/ethernet/amd/atarilance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/au1000_eth.c", "au1000_tx_timeout"], ["drivers/net/ethernet/amd/declance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/lance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/mvme147.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/ni65.c", "ni65_timeout"], ["drivers/net/ethernet/amd/nmclan_cs.c", "mace_tx_timeout"], ["drivers/net/ethernet/amd/pcnet32.c", "pcnet32_tx_timeout"], ["drivers/net/ethernet/amd/sunlance.c", "lance_tx_timeout"], ["drivers/net/ethernet/amd/xgbe/xgbe-drv.c", "xgbe_tx_timeout"], ["drivers/net/ethernet/apm/xgene-v2/main.c", "xge_timeout"], ["drivers/net/ethernet/apm/xgene/xgene_enet_main.c", "xgene_enet_timeout"], ["drivers/net/ethernet/apple/macmace.c", "mace_tx_timeout"], ["drivers/net/ethernet/atheros/ag71xx.c", "ag71xx_tx_timeout"], ["drivers/net/ethernet/atheros/alx/main.c", "alx_tx_timeout"], ["drivers/net/ethernet/atheros/atl1c/atl1c_main.c", "atl1c_tx_timeout"], ["drivers/net/ethernet/atheros/atl1e/atl1e_main.c", "atl1e_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl1.c", "atlx_tx_timeout"], ["drivers/net/ethernet/atheros/atlx/atl2.c", "atl2_tx_timeout"], ["drivers/net/ethernet/broadcom/b44.c", "b44_tx_timeout"], ["drivers/net/ethernet/broadcom/bcmsysport.c", "bcm_sysport_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2.c", "bnx2_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.h", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_cmn.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c", "bnx2x_tx_timeout"], ["drivers/net/ethernet/broadcom/bnxt/bnxt.c", "bnxt_tx_timeout"], ["drivers/net/ethernet/broadcom/genet/bcmgenet.c", "bcmgenet_timeout"], ["drivers/net/ethernet/broadcom/sb1250-mac.c", "sbmac_tx_timeout"], ["drivers/net/ethernet/broadcom/tg3.c", "tg3_tx_timeout"], ["drivers/net/ethernet/calxeda/xgmac.c", "xgmac_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_main.c", "liquidio_tx_timeout"], ["drivers/net/ethernet/cavium/liquidio/lio_vf_rep.c", "lio_vf_rep_tx_timeout"], ["drivers/net/ethernet/cavium/thunder/nicvf_main.c", "nicvf_tx_timeout"], ["drivers/net/ethernet/cirrus/cs89x0.c", "net_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cisco/enic/enic_main.c", "enic_tx_timeout"], ["drivers/net/ethernet/cortina/gemini.c", "gmac_tx_timeout"], ["drivers/net/ethernet/davicom/dm9000.c", "dm9000_timeout"], ["drivers/net/ethernet/dec/tulip/de2104x.c", "de_tx_timeout"], ["drivers/net/ethernet/dec/tulip/tulip_core.c", "tulip_tx_timeout"], ["drivers/net/ethernet/dec/tulip/winbond-840.c", "tx_timeout"], ["drivers/net/ethernet/dlink/dl2k.c", "rio_tx_timeout"], ["drivers/net/ethernet/dlink/sundance.c", "tx_timeout"], ["drivers/net/ethernet/emulex/benet/be_main.c", "be_tx_timeout"], ["drivers/net/ethernet/ethoc.c", "ethoc_tx_timeout"], ["drivers/net/ethernet/faraday/ftgmac100.c", "ftgmac100_tx_timeout"], ["drivers/net/ethernet/fealnx.c", "fealnx_tx_timeout"], ["drivers/net/ethernet/freescale/dpaa/dpaa_eth.c", "dpaa_tx_timeout"], ["drivers/net/ethernet/freescale/fec_main.c", "fec_timeout"], ["drivers/net/ethernet/freescale/fec_mpc52xx.c", "mpc52xx_fec_tx_timeout"], ["drivers/net/ethernet/freescale/fs_enet/fs_enet-main.c", "fs_timeout"], ["drivers/net/ethernet/freescale/gianfar.c", "gfar_timeout"], ["drivers/net/ethernet/freescale/ucc_geth.c", "ucc_geth_timeout"], ["drivers/net/ethernet/fujitsu/fmvj18x_cs.c", "fjn_tx_timeout"], ["drivers/net/ethernet/google/gve/gve_main.c", "gve_tx_timeout"], ["drivers/net/ethernet/hisilicon/hip04_eth.c", "hip04_timeout"], ["drivers/net/ethernet/hisilicon/hix5hd2_gmac.c", "hix5hd2_net_timeout"], ["drivers/net/ethernet/hisilicon/hns/hns_enet.c", "hns_nic_net_timeout"], ["drivers/net/ethernet/hisilicon/hns3/hns3_enet.c", "hns3_nic_net_timeout"], ["drivers/net/ethernet/huawei/hinic/hinic_main.c", "hinic_tx_timeout"], ["drivers/net/ethernet/i825xx/82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/ether1.c", "ether1_timeout"], ["drivers/net/ethernet/i825xx/lib82596.c", "i596_tx_timeout"], ["drivers/net/ethernet/i825xx/sun3_82586.c", "sun3_82586_timeout"], ["drivers/net/ethernet/ibm/ehea/ehea_main.c", "ehea_tx_watchdog"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/emac/core.c", "emac_tx_timeout"], ["drivers/net/ethernet/ibm/ibmvnic.c", "ibmvnic_tx_timeout"], ["drivers/net/ethernet/intel/e100.c", "e100_tx_timeout"], ["drivers/net/ethernet/intel/e1000/e1000_main.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/e1000e/netdev.c", "e1000_tx_timeout"], ["drivers/net/ethernet/intel/fm10k/fm10k_netdev.c", "fm10k_tx_timeout"], ["drivers/net/ethernet/intel/i40e/i40e_main.c", "i40e_tx_timeout"], ["drivers/net/ethernet/intel/iavf/iavf_main.c", "iavf_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/ice/ice_main.c", "ice_tx_timeout"], ["drivers/net/ethernet/intel/igb/igb_main.c", "igb_tx_timeout"], ["drivers/net/ethernet/intel/igbvf/netdev.c", "igbvf_tx_timeout"], ["drivers/net/ethernet/intel/ixgb/ixgb_main.c", "ixgb_tx_timeout"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_debugfs.c", "adapter->netdev->netdev_ops->ndo_tx_timeout(adapter->netdev);"], ["drivers/net/ethernet/intel/ixgbe/ixgbe_main.c", "ixgbe_tx_timeout"], ["drivers/net/ethernet/intel/ixgbevf/ixgbevf_main.c", "ixgbevf_tx_timeout"], ["drivers/net/ethernet/jme.c", "jme_tx_timeout"], ["drivers/net/ethernet/korina.c", "korina_tx_timeout"], ["drivers/net/ethernet/lantiq_etop.c", "ltq_etop_tx_timeout"], ["drivers/net/ethernet/marvell/mv643xx_eth.c", "mv643xx_eth_tx_timeout"], ["drivers/net/ethernet/marvell/pxa168_eth.c", "pxa168_eth_tx_timeout"], ["drivers/net/ethernet/marvell/skge.c", "skge_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/marvell/sky2.c", "sky2_tx_timeout"], ["drivers/net/ethernet/mediatek/mtk_eth_soc.c", "mtk_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx4/en_netdev.c", "mlx4_en_tx_timeout"], ["drivers/net/ethernet/mellanox/mlx5/core/en_main.c", "mlx5e_tx_timeout"], ["drivers/net/ethernet/micrel/ks8842.c", "ks8842_tx_timeout"], ["drivers/net/ethernet/micrel/ksz884x.c", "netdev_tx_timeout"], ["drivers/net/ethernet/microchip/enc28j60.c", "enc28j60_tx_timeout"], ["drivers/net/ethernet/microchip/encx24j600.c", "encx24j600_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.h", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/sonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/jazzsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/macsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/natsemi/natsemi.c", "ns_tx_timeout"], ["drivers/net/ethernet/natsemi/ns83820.c", "ns83820_tx_timeout"], ["drivers/net/ethernet/natsemi/xtsonic.c", "sonic_tx_timeout"], ["drivers/net/ethernet/neterion/s2io.h", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/s2io.c", "s2io_tx_watchdog"], ["drivers/net/ethernet/neterion/vxge/vxge-main.c", "vxge_tx_watchdog"], ["drivers/net/ethernet/netronome/nfp/nfp_net_common.c", "nfp_net_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/nvidia/forcedeth.c", "nv_tx_timeout"], ["drivers/net/ethernet/oki-semi/pch_gbe/pch_gbe_main.c", "pch_gbe_tx_timeout"], ["drivers/net/ethernet/packetengines/hamachi.c", "hamachi_tx_timeout"], ["drivers/net/ethernet/packetengines/yellowfin.c", "yellowfin_tx_timeout"], ["drivers/net/ethernet/pensando/ionic/ionic_lif.c", "ionic_tx_timeout"], ["drivers/net/ethernet/qlogic/netxen/netxen_nic_main.c", "netxen_tx_timeout"], ["drivers/net/ethernet/qlogic/qla3xxx.c", "ql3xxx_tx_timeout"], ["drivers/net/ethernet/qlogic/qlcnic/qlcnic_main.c", "qlcnic_tx_timeout"], ["drivers/net/ethernet/qualcomm/emac/emac.c", "emac_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_spi.c", "qcaspi_netdev_tx_timeout"], ["drivers/net/ethernet/qualcomm/qca_uart.c", "qcauart_netdev_tx_timeout"], ["drivers/net/ethernet/rdc/r6040.c", "r6040_tx_timeout"], ["drivers/net/ethernet/realtek/8139cp.c", "cp_tx_timeout"], ["drivers/net/ethernet/realtek/8139too.c", "rtl8139_tx_timeout"], ["drivers/net/ethernet/realtek/atp.c", "tx_timeout"], ["drivers/net/ethernet/realtek/r8169_main.c", "rtl8169_tx_timeout"], ["drivers/net/ethernet/renesas/ravb_main.c", "ravb_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/renesas/sh_eth.c", "sh_eth_tx_timeout"], ["drivers/net/ethernet/samsung/sxgbe/sxgbe_main.c", "sxgbe_tx_timeout"], ["drivers/net/ethernet/seeq/ether3.c", "ether3_timeout"], ["drivers/net/ethernet/seeq/sgiseeq.c", "timeout"], ["drivers/net/ethernet/sfc/efx.c", "efx_watchdog"], ["drivers/net/ethernet/sfc/falcon/efx.c", "ef4_watchdog"], ["drivers/net/ethernet/sgi/ioc3-eth.c", "ioc3_timeout"], ["drivers/net/ethernet/sgi/meth.c", "meth_tx_timeout"], ["drivers/net/ethernet/silan/sc92031.c", "sc92031_tx_timeout"], ["drivers/net/ethernet/sis/sis190.c", "sis190_tx_timeout"], ["drivers/net/ethernet/sis/sis900.c", "sis900_tx_timeout"], ["drivers/net/ethernet/smsc/epic100.c", "epic_tx_timeout"], ["drivers/net/ethernet/smsc/smc911x.c", "smc911x_timeout"], ["drivers/net/ethernet/smsc/smc9194.c", "smc_timeout"], ["drivers/net/ethernet/smsc/smc91c92_cs.c", "smc_tx_timeout"], ["drivers/net/ethernet/smsc/smc91x.c", "smc_timeout"], ["drivers/net/ethernet/stmicro/stmmac/stmmac_main.c", "stmmac_tx_timeout"], ["drivers/net/ethernet/sun/cassini.c", "cas_tx_timeout"], ["drivers/net/ethernet/sun/ldmvsw.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/niu.c", "niu_tx_timeout"], ["drivers/net/ethernet/sun/sunbmac.c", "bigmac_tx_timeout"], ["drivers/net/ethernet/sun/sungem.c", "gem_tx_timeout"], ["drivers/net/ethernet/sun/sunhme.c", "happy_meal_tx_timeout"], ["drivers/net/ethernet/sun/sunqe.c", "qe_tx_timeout"], ["drivers/net/ethernet/sun/sunvnet.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.c", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/sun/sunvnet_common.h", "sunvnet_tx_timeout_common"], ["drivers/net/ethernet/synopsys/dwc-xlgmac-net.c", "xlgmac_tx_timeout"], ["drivers/net/ethernet/ti/cpmac.c", "cpmac_tx_timeout"], ["drivers/net/ethernet/ti/cpsw.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.c", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/cpsw_priv.h", "cpsw_ndo_tx_timeout"], ["drivers/net/ethernet/ti/davinci_emac.c", "emac_dev_tx_timeout"], ["drivers/net/ethernet/ti/netcp_core.c", "netcp_ndo_tx_timeout"], ["drivers/net/ethernet/ti/tlan.c", "tlan_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.h", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_net.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/ps3_gelic_wireless.c", "gelic_net_tx_timeout"], ["drivers/net/ethernet/toshiba/spider_net.c", "spider_net_tx_timeout"], ["drivers/net/ethernet/toshiba/tc35815.c", "tc35815_tx_timeout"], ["drivers/net/ethernet/via/via-rhine.c", "rhine_tx_timeout"], ["drivers/net/ethernet/wiznet/w5100.c", "w5100_tx_timeout"], ["drivers/net/ethernet/wiznet/w5300.c", "w5300_tx_timeout"], ["drivers/net/ethernet/xilinx/xilinx_emaclite.c", "xemaclite_tx_timeout"], ["drivers/net/ethernet/xircom/xirc2ps_cs.c", "xirc_tx_timeout"], ["drivers/net/fjes/fjes_main.c", "fjes_tx_retry"], ["drivers/net/slip/slip.c", "sl_tx_timeout"], ["include/linux/usb/usbnet.h", "usbnet_tx_timeout"], ["drivers/net/usb/aqc111.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/asix_devices.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88172a.c", "usbnet_tx_timeout"], ["drivers/net/usb/ax88179_178a.c", "usbnet_tx_timeout"], ["drivers/net/usb/catc.c", "catc_tx_timeout"], ["drivers/net/usb/cdc_mbim.c", "usbnet_tx_timeout"], ["drivers/net/usb/cdc_ncm.c", "usbnet_tx_timeout"], ["drivers/net/usb/dm9601.c", "usbnet_tx_timeout"], ["drivers/net/usb/hso.c", "hso_net_tx_timeout"], ["drivers/net/usb/int51x1.c", "usbnet_tx_timeout"], ["drivers/net/usb/ipheth.c", "ipheth_tx_timeout"], ["drivers/net/usb/kaweth.c", "kaweth_tx_timeout"], ["drivers/net/usb/lan78xx.c", "lan78xx_tx_timeout"], ["drivers/net/usb/mcs7830.c", "usbnet_tx_timeout"], ["drivers/net/usb/pegasus.c", "pegasus_tx_timeout"], ["drivers/net/usb/qmi_wwan.c", "usbnet_tx_timeout"], ["drivers/net/usb/r8152.c", "rtl8152_tx_timeout"], ["drivers/net/usb/rndis_host.c", "usbnet_tx_timeout"], ["drivers/net/usb/rtl8150.c", "rtl8150_tx_timeout"], ["drivers/net/usb/sierra_net.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc75xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/smsc95xx.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9700.c", "usbnet_tx_timeout"], ["drivers/net/usb/sr9800.c", "usbnet_tx_timeout"], ["drivers/net/usb/usbnet.c", "usbnet_tx_timeout"], ["drivers/net/vmxnet3/vmxnet3_drv.c", "vmxnet3_tx_timeout"], ["drivers/net/wan/cosa.c", "cosa_net_timeout"], ["drivers/net/wan/farsync.c", "fst_tx_timeout"], ["drivers/net/wan/fsl_ucc_hdlc.c", "uhdlc_tx_timeout"], ["drivers/net/wan/lmc/lmc_main.c", "lmc_driver_timeout"], ["drivers/net/wan/x25_asy.c", "x25_asy_timeout"], ["drivers/net/wimax/i2400m/netdev.c", "i2400m_tx_timeout"], ["drivers/net/wireless/intel/ipw2x00/ipw2100.c", "ipw2100_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/hostap/hostap_main.c", "prism2_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/main.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco_usb.c", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/orinoco/orinoco.h", "orinoco_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_dev.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.c", "islpci_eth_tx_timeout"], ["drivers/net/wireless/intersil/prism54/islpci_eth.h", "islpci_eth_tx_timeout"], ["drivers/net/wireless/marvell/mwifiex/main.c", "mwifiex_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.c", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/quantenna/qtnfmac/core.h", "qtnf_netdev_tx_timeout"], ["drivers/net/wireless/rndis_wlan.c", "usbnet_tx_timeout"], ["drivers/net/wireless/wl3501_cs.c", "wl3501_tx_timeout"], ["drivers/net/wireless/zydas/zd1201.c", "zd1201_tx_timeout"], ["drivers/s390/net/qeth_core.h", "qeth_tx_timeout"], ["drivers/s390/net/qeth_core_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l2_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/s390/net/qeth_l3_main.c", "qeth_tx_timeout"], ["drivers/staging/ks7010/ks_wlan_net.c", "ks_wlan_tx_timeout"], ["drivers/staging/qlge/qlge_main.c", "qlge_tx_timeout"], ["drivers/staging/rtl8192e/rtl8192e/rtl_core.c", "_rtl92e_tx_timeout"], ["drivers/staging/rtl8192u/r8192U_core.c", "tx_timeout"], ["drivers/staging/unisys/visornic/visornic_main.c", "visornic_xmit_timeout"], ["drivers/staging/wlan-ng/p80211netdev.c", "p80211knetdev_tx_timeout"], ["drivers/tty/n_gsm.c", "gsm_mux_net_tx_timeout"], ["drivers/tty/synclink.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclink_gt.c", "hdlcdev_tx_timeout"], ["drivers/tty/synclinkmp.c", "hdlcdev_tx_timeout"], ["net/atm/lec.c", "lec_tx_timeout"], ["net/bluetooth/bnep/netdev.c", "bnep_net_timeout"] ); for my $p (@work) { my @pair = @$p; my $file = $pair[0]; my $func = $pair[1]; print STDERR $file , ": ", $func,"\n"; our @ARGV = ($file); while (<ARGV>) { if (m/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/) { print STDERR "found $1+$2 in $file\n"; } if (s/($func\s*\(struct\s+net_device\s+\*[A-Za-z_]?[A-Za-z-0-9_]*)(\))/$1, unsigned int txqueue$2/) { print STDERR "$func found in $file\n"; } print; } } where the list of files and functions is simply from: git grep ndo_tx_timeout, with manual addition of headers in the rare cases where the function is from a header, then manually changing the few places which actually call ndo_tx_timeout. Signed-off-by: Michael S. Tsirkin <mst@redhat.com> Acked-by: Heiner Kallweit <hkallweit1@gmail.com> Acked-by: Jakub Kicinski <jakub.kicinski@netronome.com> Acked-by: Shannon Nelson <snelson@pensando.io> Reviewed-by: Martin Habets <mhabets@solarflare.com> changes from v9: fixup a forward declaration changes from v9: more leftovers from v3 change changes from v8: fix up a missing direct call to timeout rebased on net-next changes from v7: fixup leftovers from v3 change changes from v6: fix typo in rtl driver changes from v5: add missing files (allow any net device argument name) changes from v4: add a missing driver header changes from v3: change queue # to unsigned Changes from v2: added headers Changes from v1: Fix errors found by kbuild: generalize the pattern a bit, to pick up a couple of instances missed by the previous version. Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2019-09-18 | Merge git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next | Linus Torvalds | |
| Pull networking updates from David Miller: 1) Support IPV6 RA Captive Portal Identifier, from Maciej Żenczykowski. 2) Use bio_vec in the networking instead of custom skb_frag_t, from Matthew Wilcox. 3) Make use of xmit_more in r8169 driver, from Heiner Kallweit. 4) Add devmap_hash to xdp, from Toke Høiland-Jørgensen. 5) Support all variants of 5750X bnxt_en chips, from Michael Chan. 6) More RTNL avoidance work in the core and mlx5 driver, from Vlad Buslov. 7) Add TCP syn cookies bpf helper, from Petar Penkov. 8) Add 'nettest' to selftests and use it, from David Ahern. 9) Add extack support to drop_monitor, add packet alert mode and support for HW drops, from Ido Schimmel. 10) Add VLAN offload to stmmac, from Jose Abreu. 11) Lots of devm_platform_ioremap_resource() conversions, from YueHaibing. 12) Add IONIC driver, from Shannon Nelson. 13) Several kTLS cleanups, from Jakub Kicinski. * git://git.kernel.org/pub/scm/linux/kernel/git/netdev/net-next: (1930 commits) mlxsw: spectrum_buffers: Add the ability to query the CPU port's shared buffer mlxsw: spectrum: Register CPU port with devlink mlxsw: spectrum_buffers: Prevent changing CPU port's configuration net: ena: fix incorrect update of intr_delay_resolution net: ena: fix retrieval of nonadaptive interrupt moderation intervals net: ena: fix update of interrupt moderation register net: ena: remove all old adaptive rx interrupt moderation code from ena_com net: ena: remove ena_restore_ethtool_params() and relevant fields net: ena: remove old adaptive interrupt moderation code from ena_netdev net: ena: remove code duplication in ena_com_update_nonadaptive_moderation_interval _*() net: ena: enable the interrupt_moderation in driver_supported_features net: ena: reimplement set/get_coalesce() net: ena: switch to dim algorithm for rx adaptive interrupt moderation net: ena: add intr_moder_rx_interval to struct ena_com_dev and use it net: phy: adin: implement Energy Detect Powerdown mode via phy-tunable ethtool: implement Energy Detect Powerdown support via phy-tunable xen-netfront: do not assume sk_buff_head list is empty in error handling s390/ctcm: Delete unnecessary checks before the macro call “dev_kfree_skb” net: ena: don't wake up tx queue when down drop_monitor: Better sanitize notified packets ... | |||
| 2019-09-07 | ethernet: micrel: Use DIV_ROUND_CLOSEST directly to make it readable | zhong jiang | |
| The kernel.h macro DIV_ROUND_CLOSEST performs the computation (x + d/2)/d but is perhaps more readable. Signed-off-by: zhong jiang <zhongjiang@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2019-09-04 | net: remove ks8695 driver | Arnd Bergmann | |
| The platform is getting removed, so there are no remaining users of this driver. Link: https://lore.kernel.org/r/20190809202749.742267-6-arnd@arndb.de Signed-off-by: Arnd Bergmann <arnd@arndb.de> | |||
| 2019-08-22 | ethernet: Delete unnecessary checks before the macro call “dev_kfree_skb” | Markus Elfring | |
| The dev_kfree_skb() function performs also input parameter validation. Thus the test around the shown calls is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2019-08-21 | net: ks8851-ml: use devm_platform_ioremap_resource() to simplify code | YueHaibing | |
| Use devm_platform_ioremap_resource() to simplify the code a bit. This is detected by coccinelle. Reported-by: Hulk Robot <hulkci@huawei.com> Signed-off-by: YueHaibing <yuehaibing@huawei.com> Signed-off-by: David S. Miller <davem@davemloft.net> | |||
| 2019-06-19 | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500 | Thomas Gleixner | |
| Based on 2 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation # extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 4122 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Enrico Weigelt <info@metux.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Allison Randal <allison@lohutok.net> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||
| 2019-05-30 | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 176 | Thomas Gleixner | |
| Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details you should have received a copy of the gnu general public license along with this program if not write to the free software foundation inc 675 mass ave cambridge ma 02139 usa extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 44 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Steve Winslow <swinslow@gmail.com> Reviewed-by: Alexios Zavras <alexios.zavras@intel.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190528170025.980374610@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||
| 2019-05-30 | treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 174 | Thomas Gleixner | |
| Based on 1 normalized pattern(s): this program is free software you can redistribute it and or modify it under the terms of the gnu general public license version 2 as published by the free software foundation this program is distributed in the hope that it will be useful but without any warranty without even the implied warranty of merchantability or fitness for a particular purpose see the gnu general public license for more details extracted by the scancode license scanner the SPDX license identifier GPL-2.0-only has been chosen to replace the boilerplate/reference in 655 file(s). Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Reviewed-by: Allison Randal <allison@lohutok.net> Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org> Reviewed-by: Richard Fontana <rfontana@redhat.com> Cc: linux-spdx@vger.kernel.org Link: https://lkml.kernel.org/r/20190527070034.575739538@linutronix.de Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org> | |||
 |
index : linux.git | |
| Unnamed repository; edit this file 'description' to name the repository. |
| summaryrefslogtreecommitdiff |