| Age | Commit message (Collapse) | Author |
|---|
|
if the NIC fails to validate the checksum on TCP/UDP, and validation of IP
checksum is successful, the driver subtracts the pseudo-header checksum
from the value obtained by the hardware and sets CHECKSUM_COMPLETE. Don't
do that if protocol is IPPROTO_SCTP, otherwise CRC32c validation fails.
V2: don't test MLX4_CQE_STATUS_IPV6 if MLX4_CQE_STATUS_IPV4 is set
Reported-by: Shuang Li <shuali@redhat.com>
Fixes: f8c6455bb04b ("net/mlx4_en: Extend checksum offloading by CHECKSUM COMPLETE")
Signed-off-by: Davide Caratti <dcaratti@redhat.com>
Acked-by: Saeed Mahameed <saeedm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Each multicast group (MID) stores a bitmap of ports to which a packet
should be forwarded to in case an MDB entry associated with the MID is
hit.
Since the initial introduction of IGMP snooping in commit 3a49b4fde2a1
("mlxsw: Adding layer 2 multicast support") the driver didn't correctly
free these multicast groups upon ungraceful situations such as the
removal of the upper bridge device or module removal.
The correct way to fix this is to associate each MID with the bridge
ports member in it and then drop the reference in case the bridge port
is destroyed, but this will result in a lot more code and will be fixed
in net-next.
For now, upon module removal, traverse the MID list and release each
one.
Fixes: 3a49b4fde2a1 ("mlxsw: Adding layer 2 multicast support")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some operations in the bridge driver such as MDB deletion are preformed
in an atomic context and thus deferred to a process context by the
switchdev infrastructure.
Therefore, by the time the operation is performed by the underlying
device driver it's possible the bridge port context is already gone.
This is especially true for removal flows, but theoretically can also be
invoked during addition.
Remove the warnings in such situations and return normally.
Fixes: c57529e1d5d8 ("mlxsw: spectrum: Replace vPorts with Port-VLAN")
Fixes: 3922285d96e7 ("net: bridge: Add support for offloading port attributes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
QUERY_DEV_CAP_DIAG_RPRT_PER_PORT
However, it failed to introduce a corresponding entry in function
dump_dev_cap_flags2() for outputting a line in the message log
when this capability bit is set.
The change here fixes that omission.
Fixes: c7c122ed67e4 ("net/mlx4: Add diagnostic counters capability bit")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The cited commit introduced the following new enum value in file
include/linux/mlx4/device.h:
MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP
However the value of MLX4_DEV_CAP_FLAG2_SVLAN_BY_QP needs to stay
consistent with the value used in another namespace in
function dump_dev_cap_flags2(), which is manually kept in sync.
The change here restores that consistency.
Fixes: 7c3d21c8153c ("net/mlx4_core: Preparation for VF vlan protocol 802.1ad")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The index value in function dump_dev_cap_flags2() for outputting
"sl to vl mapping table change event support" needs to be
consistent with the value of the enumerated constant
MLX4_DEV_CAP_FLAG2_SL_TO_VL_CHANGE_EVENT defined in file
include/linux/mlx4_device.h
The change here restores that consistency.
Fixes: fd10ed8e6f42 ("IB/mlx4: Fix possible vl/sl field mismatch in LRH header in QP1 packets")
Reported-by: Mukesh Kacker <mukesh.kacker@oracle.com>
Signed-off-by: Jack Morgenstein <jackm@dev.mellanox.co.il>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently when WoL is supported but disabled, ethtool reports:
"Supports Wake-on: d".
Fix the indication of Wol support, so that the indication
remains "g" all the time if the NIC supports WoL.
Tested:
As accepted, when NIC supports WoL- ethtool reports:
Supports Wake-on: g
Wake-on: d
when NIC doesn't support WoL- ethtool reports:
Supports Wake-on: d
Wake-on: d
Fixes: 14c07b1358ed ("mlx4: Wake on LAN support")
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When adding ethtool steering rule with action DISCARD we wrongly
pass a NULL dest with dest_num 1 to mlx5_add_flow_rules().
What this error seems to have caused is sending VPORT 0
(MLX5_FLOW_DESTINATION_TYPE_VPORT) as the fte dest instead of no dests.
We have fte action correctly set to DROP so it might been ignored
anyways.
To reproduce use:
# sudo ethtool --config-nfc <dev> flow-type ether \
dst aa:bb:cc:dd:ee:ff action -1
Fixes: 74491de93712 ("net/mlx5: Add multi dest support")
Signed-off-by: Paul Blakey <paulb@mellanox.com>
Reviewed-by: Mark Bloch <markb@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
This is done in order to ensure that work will not run after the cleanup.
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The overflow_period is calculated in seconds. In order to use it
for delayed work scheduling translation to jiffies is needed.
Fixes: ef9814deafd0 ('net/mlx5e: Add HW timestamping (TS) support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Add the missing option to enable the PTP_CLK_PPS function.
In this case pin should be configured as 1PPS IN first and
then it will be connected to PPS mechanism.
Events will be reported as PTP_CLOCK_PPSUSR events to relevant sysfs.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to fix the drift in 1PPS out need to adjust the next pulse.
On each 1PPS out falling edge driver gets the event, then the event
handler adjusts the next pulse starting time.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Need to disable the MTPPS and unsubscribe from the pulse events
when user disables the 1PPS functionality.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In order to mark relevant fields while setting the MTPPS register
add field select. Otherwise it can cause a misconfiguration in
firmware.
Fixes: ee7f12205abc ('net/mlx5e: Implement 1PPS support')
Signed-off-by: Eugenia Emantayev <eugenia@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
outer_header_zero() routine checks if the outer_headers match of a
flow-table entry are all zero.
This function uses the size of whole fte_match_param, instead of just
the outer_headers member, causing failure to detect all-zeros if
any other members of the fte_match_param are non-zero.
Use the correct size for zero check.
Fixes: 6dc6071cfcde ("net/mlx5e: Add ethtool flow steering support")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
On interface remove, the clean-up was done incorrectly causing
an error in the log:
"SET_FLOW_TABLE_ROOT(0x92f) op_mod(0x0) failed...syndrome (0x7e9f14)"
This was caused by the following flow:
-ndo_uninit:
Move QP state to RST (this disconnects the QP from FT),
the QP cannot be attached to any FT unless it is in RTS.
-mlx5_rdma_netdev_free:
cleanup_rx: Destroy FT
cleanup_tx: Destroy QP and remove QPN from FT
This caused a problem when destroying current FT we tried to
re-attach the QP to the next FT which is not needed.
The correct flow is:
-mlx5_rdma_netdev_free:
cleanup_rx: remove QPN from FT & Destroy FT
cleanup_tx: Destroy QP
Fixes: 508541146af1 ("net/mlx5: Use underlay QPN from the root name space")
Signed-off-by: Alex Vesker <valex@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
When driver fail to allocate an entry to send command to FW, it must
notify the calling function and release the memory allocated for
this command.
Fixes: e126ba97dba9e ('mlx5: Add driver for Mellanox Connect-IB adapters')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Completion on timeout should not free the driver command entry structure
as it will need to access it again once real completion event from FW
will occur.
Fixes: 73dd3a4839c1 ('net/mlx5: Avoid using pending command interface slots')
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Cc: kernel-team@fb.com
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
The tx_enabled lag event field is used to determine whether a slave is
active.
Current logic uses this value only if the mode is active-backup.
However, LACP mode, although considered a load balancing mode, can mark
a slave as inactive in certain situations (e.g., LACP timeout).
This fix takes the tx_enabled value into account when remapping, with
no respect to the LAG mode (this should not affect the behavior in XOR
mode, since in this mode both slaves are marked as active).
Fixes: 7907f23adc18 (net/mlx5: Implement RoCE LAG feature)
Signed-off-by: Aviv Heller <avivh@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Upon sriov enable, eswitch is always enabled.
Currently, if enable hca failed over all VFs, we would skip eswitch
disable as part of sriov disable, which will lead to resources leak.
Fix it by disabling eswitch if it was enabled (use indication from
eswitch mode).
Fixes: 6b6adee3dad2 ('net/mlx5: SRIOV core code refactoring')
Signed-off-by: Eran Ben Elisha <eranbe@mellanox.com>
Signed-off-by: Noa Osherovich <noaos@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Each FIB node holds a linked list of routes sharing the same prefix and
length. In the case of IPv4 it's ordered according to table ID, metric
and TOS and only the first route in the list is actually programmed to
the device.
In case a gatewayed route is added somewhere in the list, then after its
nexthop group will be refreshed and become valid (due to the resolution
of its gateway), it'll mistakenly overwrite the existing entry.
Example:
192.168.200.0/24 dev enp3s0np3 scope link metric 1000 offload
192.168.200.0/24 via 192.168.100.1 dev enp3s0np3 metric 1000 offload
Both routes are marked as offloaded despite the fact only the first one
should actually be present in the device's table.
When refreshing the nexthop group, don't write the route to the device's
table unless it's the first in its node.
Fixes: 9aecce1c7d97 ("mlxsw: spectrum_router: Correctly handle identical routes")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pull networking fixes from David Miller:
1) BPF verifier signed/unsigned value tracking fix, from Daniel
Borkmann, Edward Cree, and Josef Bacik.
2) Fix memory allocation length when setting up calls to
->ndo_set_mac_address, from Cong Wang.
3) Add a new cxgb4 device ID, from Ganesh Goudar.
4) Fix FIB refcount handling, we have to set it's initial value before
the configure callback (which can bump it). From David Ahern.
5) Fix double-free in qcom/emac driver, from Timur Tabi.
6) A bunch of gcc-7 string format overflow warning fixes from Arnd
Bergmann.
7) Fix link level headroom tests in ip_do_fragment(), from Vasily
Averin.
8) Fix chunk walking in SCTP when iterating over error and parameter
headers. From Alexander Potapenko.
9) TCP BBR congestion control fixes from Neal Cardwell.
10) Fix SKB fragment handling in bcmgenet driver, from Doug Berger.
11) BPF_CGROUP_RUN_PROG_SOCK_OPS needs to check for null __sk, from Cong
Wang.
12) xmit_recursion in ppp driver needs to be per-device not per-cpu,
from Gao Feng.
13) Cannot release skb->dst in UDP if IP options processing needs it.
From Paolo Abeni.
14) Some netdev ioctl ifr_name[] NULL termination fixes. From Alexander
Levin and myself.
15) Revert some rtnetlink notification changes that are causing
regressions, from David Ahern.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (83 commits)
net: bonding: Fix transmit load balancing in balance-alb mode
rds: Make sure updates to cp_send_gen can be observed
net: ethernet: ti: cpsw: Push the request_irq function to the end of probe
ipv4: initialize fib_trie prior to register_netdev_notifier call.
rtnetlink: allocate more memory for dev_set_mac_address()
net: dsa: b53: Add missing ARL entries for BCM53125
bpf: more tests for mixed signed and unsigned bounds checks
bpf: add test for mixed signed and unsigned bounds checks
bpf: fix up test cases with mixed signed/unsigned bounds
bpf: allow to specify log level and reduce it for test_verifier
bpf: fix mixed signed/unsigned derived min/max value bounds
ipv6: avoid overflow of offset in ip6_find_1stfragopt
net: tehuti: don't process data if it has not been copied from userspace
Revert "rtnetlink: Do not generate notifications for CHANGEADDR event"
net: dsa: mv88e6xxx: Enable CMODE config support for 6390X
dt-binding: ptp: Add SoC compatibility strings for dte ptp clock
NET: dwmac: Make dwmac reset unconditional
net: Zero terminate ifr_name in dev_ifname().
wireless: wext: terminate ifr name coming from userspace
netfilter: fix netfilter_net_init() return
...
|
|
The caller to the driver marks GFP_NOIO allocations with help
of memalloc_noio-* calls now. This makes redundant to pass down
to the driver gfp flags, which can be GFP_KERNEL only.
The patch removes the gfp flags argument and updates all driver paths.
Signed-off-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: Leon Romanovsky <leon@kernel.org>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
The function __mlx4_zone_remove_one_entry always returns zero. So
it is not necessary to check it.
Cc: Joe Jin <joe.jin@oracle.com>
Cc: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We can't rely on kzalloc() always succeeding, so check its return value.
Suppresses the following smatch error:
mlxsw_sp_switchdev_event() error: potential null dereference
'switchdev_work->fdb_info.addr'. (kzalloc returns
null)
Fixes: af061378924f ("mlxsw: spectrum_switchdev: Add support for learning FDB through notification")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge
port attributes/vlan set") removed statements that used 'bridge_vlan',
but didn't remove the variable itself resulting in the following warning
with W=1:
warning: variable ‘bridge_vlan’ set but not used
[-Wunused-but-set-variable]
Remove the variable and suppress the warning.
Fixes: 10e23eb299fa ("mlxsw: spectrum: Remove support for bypass bridge port attributes/vlan set")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While working on IPv6 route replace I realized we can have a
use-after-free in IPv4 in case the replaced route is offloaded and the
only one using its FIB info.
The problem is that fib_table_insert() drops the reference on the FIB
info of the replaced routes which is eventually freed via call_rcu().
Since the driver doesn't hold a reference on this FIB info it can cause
a use-after-free when it tries to clear the RTNH_F_OFFLOAD flag stored
in fi->fib_flags.
After running the following commands in a loop for enough time with a
KASAN enabled kernel I finally got the below trace.
$ ip route add 192.168.50.0/24 via 192.168.200.1 dev enp3s0np3
$ ip route replace 192.168.50.0/24 dev enp3s0np5
$ ip route del 192.168.50.0/24 dev enp3s0np5
BUG: KASAN: use-after-free in mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
Read of size 4 at addr ffff8803717d9820 by task kworker/u4:2/55
[...]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
? mlxsw_sp_router_neighs_update_work+0x1cd0/0x1ce0 [mlxsw_spectrum]
? mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
__asan_load4+0x61/0x80
mlxsw_sp_fib_entry_offload_unset+0xa7/0x120 [mlxsw_spectrum]
mlxsw_sp_fib_entry_offload_refresh+0xb6/0x370 [mlxsw_spectrum]
mlxsw_sp_router_fib_event_work+0xd1c/0x2780 [mlxsw_spectrum]
[...]
Freed by task 5131:
save_stack_trace+0x16/0x20
save_stack+0x46/0xd0
kasan_slab_free+0x70/0xc0
kfree+0x144/0x570
free_fib_info_rcu+0x2e7/0x410
rcu_process_callbacks+0x4f8/0xe30
__do_softirq+0x1d3/0x9e2
Fix this by taking a reference on the FIB info when creating the nexthop
group it represents and drop it when the group is destroyed.
Fixes: 599cf8f95f22 ("mlxsw: spectrum_router: Add support for route replace")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With this patch the error path of mlxsw_sp_nexthop_init() is symmetric
with mlxsw_sp_nexthop_fini(). Noticed during code review.
Fixes: a8c970142798 ("mlxsw: spectrum_router: Refactor nexthop init routine")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The new IPSec offload code introduced a build error:
drivers/net/ethernet/mellanox/mlx5/core/en_accel/ipsec_rxtx.o: In function `mlx5e_ipsec_build_inverse_table':
ipsec_rxtx.c:(.text+0x556): undefined reference
Another patch was added on top to fix the build error, but
that introduced a new bug, as we now use the remainder of
the division rather than the result.
This makes it use the correct helper function instead.
Fixes: 5dfd87b67cd9 ("net/mlx5: IPSec, Fix 64-bit division on 32-bit builds")
Fixes: 2ac9cfe78223 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Latest change in open-lldp code uses bytes 6-11 of perm_addr buffer
as the Ethernet source address for the host TLV packet.
Since our driver does not fill these bytes, they stay at zero and
the open-lldp code ends up sending the TLV packet with zero source
address and the switch drops this packet.
The fix is to initialize these bytes to 0xff. The open-lldp code
considers 0xff:ff:ff:ff:ff:ff as the invalid address and falls back to
use the host's mac address as the Ethernet source address.
Fixes: 3a6a931dfb8e ("net/mlx5e: Support DCBX CEE API")
Signed-off-by: Huy Nguyen <huyn@mellanox.com>
Reviewed-by: Daniel Jurgens <danielj@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Currently it is not possible to build just one .o file inside
a subdirectory, because the subdirectories lack a Makefile.
Add a Makefile to the mlx5 subdirectories.
Fixes: e29341fb3a5b ("net/mlx5: FPGA, Add basic support for Innova")
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reported-by: David Miller <davem@davemloft.net>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Both the ethernet and FPGA portions of MLX5 now require the wq functions,
and we get a link error when CONFIG_MLX5_CORE_EN is disabled:
drivers/net/ethernet/mellanox/mlx5/core/fpga/conn.o: In function `mlx5_fpga_conn_create_cq':
conn.c:(.text+0x10b3): undefined reference to `mlx5_cqwq_create'
conn.c:(.text+0x10c6): undefined reference to `mlx5_cqwq_get_size'
conn.c:(.text+0x12bc): undefined reference to `mlx5_cqwq_destroy'
Build wq.o even if MLX5_CORE_EN is not selected.
Fixes: 537a50574175 ("net/mlx5: FPGA, Add high-speed connection routines")
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/fpga/ipsec.c:313:36: warning: cast to restricted __be32
drivers/net/ethernet/mellanox/mlx5/core/fpga/ipsec.c:314:37: warning: cast to restricted __be32
Fixes: bebb23e6cb02 ("net/mlx5: Accel, Add IPSec acceleration interface")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warning when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/fpga/core.c:105:5: warning: symbol 'mlx5_fpga_device_brb' was not declared. Should it be static?
Fixes: c43051d72a8d ("net/mlx5: FPGA, Add SBU bypass and reset flows")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building 386 kernel:
>> ERROR: "__udivdi3" [drivers/net/ethernet/mellanox/mlx5/core/mlx5_core.ko] undefined!
Fixes: 2ac9cfe78223 ("net/mlx5e: IPSec, Add Innova IPSec offload TX data path")
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Fix warnings when building with -Wall:
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:38:6: warning: symbol 'mlx5_init_reserved_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:47:6: warning: symbol 'mlx5_cleanup_reserved_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:55:5: warning: symbol 'mlx5_core_reserve_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:79:6: warning: symbol 'mlx5_core_unreserve_gids' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:92:5: warning: symbol 'mlx5_core_reserved_gid_alloc' was not declared. Should it be static?
drivers/net/ethernet/mellanox/mlx5/core/lib/gid.c:109:6: warning: symbol 'mlx5_core_reserved_gid_free' was not declared. Should it be static?
Fixes: 52ec462eca9b ("net/mlx5: Add reserved-gids support")
Reported-by: Or Gerlitz <gerlitz.or@gmail.com>
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
Some overlapping changes in the mlx5 driver.
A merge conflict resolution posted by Stephen Rothwell was used as a
guide.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The variable mlx4_log_num_mgm_entry_size is only called in main.c.
CC: Joe Jin <joe.jin@oracle.com>
CC: Junxiao Bi <junxiao.bi@oracle.com>
Signed-off-by: Zhu Yanjun <yanjun.zhu@oracle.com>
Reviewed-by: Yuval Shaia <yuval.shaia@oracle.com>
Reviewed-by: Leon Romanovsky <leonro@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If mlx5 is set to be built-in and mlxfw as a module, we
get a link error:
drivers/built-in.o: In function `mlx5_firmware_flash':
(.text+0x5aed72): undefined reference to `mlxfw_firmware_flash'
Since we don't want to mandate selecting mlxfw for mlx5 users, we
use the IS_REACHABLE macro to make sure that a stub is exposed
to the caller.
Signed-off-by: Or Gerlitz <ogerlitz@mellanox.com>
Reported-by: Jakub Kicinski <kubakici@wp.pl>
Reported-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in mlx5_core_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
Mellanox, mlx5 fixes 2017-06-28
This series contains some fixes for the mlx5 core and netdev driver.
Please pull and let me know if there's any problem.
For -stable:
("net/mlx5e: Fix TX carrier errors report in get stats ndo") Kernels >= v4.7
("net/mlx5: Cancel delayed recovery work when unloading the driver") Kernels >= v4.10
* When applied to net-next this will introduce a contextual conflict, it
should be easy to resolve, (a spin_lock was changed to spin_lock_irqsave in net-next),
if you need any help with this please let me know.
("net/mlx5: Fix driver load error flow when firmware is stuck") Kernels >= v4.4*
* This patch fixes: 6c780a0267b8 ("net/mlx5: Wait for FW readiness before initializing command interface")
which was submitted two weeks ago and queued up for v4.4.
Sorry about the mess, but other than the above, this series doesn't introduce
any conflict with the current mlx5 IPSec offload series.
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A set of overlapping changes in macvlan and the rocker
driver, nothing serious.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently the number of TX queues that are allocated doesn't depend
on the number of TCs, the module always loads with max num of UP
per channel.
In order to prevent the allocation of unnecessary memory, the
module will load with minimum number of UPs per channel, and the
user will be able to control the number of TX queues per channel
by changing the number of TC to 8 using the tc command.
The variable num_up will hold the information about the current
number of UPs.
Due to the change, needed to remove the lines that set the value of
UP to be different than zero in the func "mlx4_en_select_queue",
since now the num of TX queues that are allocated is only one per channel
in default.
In order not to force the UP to be zero in case of only one TC, added
a condition before forcing it in the func "mlx4_en_fill_qp_context".
Tested:
After the module is loaded with minimum number of UP per channel, to
increase num of TCs to 8, use:
tc qdisc add dev ens8 root mqprio num_tc 8
In order to decrease the number of TCs to minimum number of UP per channel,
use:
tc qdisc del dev ens8 root
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until this patch, the number of UPs was hard coded for eight.
Replace this with a variable in struct "mlx4_en_port_profile".
Currently, the variable will hold the maximum number of UP,
as before.
The patch creates an infrastructure to add an option for dynamic
change of the actual number of TCs.
Signed-off-by: Inbar Karmy <inbark@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Cc: Tarick Bedeir <tarick@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case a VLAN device is enslaved to a bridge we shouldn't create a
router interface (RIF) for it when it's configured with an IP address.
This is already handled by the driver for other types of netdevs, such
as physical ports and LAG devices.
If this IP address is then removed and the interface is subsequently
unlinked from the bridge, a NULL pointer dereference can happen, as the
original 802.1d FID was replaced with an rFID which was then deleted.
To reproduce:
$ ip link set dev enp3s0np9 up
$ ip link add name enp3s0np9.111 link enp3s0np9 type vlan id 111
$ ip link set dev enp3s0np9.111 up
$ ip link add name br0 type bridge
$ ip link set dev br0 up
$ ip link set enp3s0np9.111 master br0
$ ip address add dev enp3s0np9.111 192.168.0.1/24
$ ip address del dev enp3s0np9.111 192.168.0.1/24
$ ip link set dev enp3s0np9.111 nomaster
Fixes: 99724c18fc66 ("mlxsw: spectrum: Introduce support for router interfaces")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Reported-by: Petr Machata <petrm@mellanox.com>
Tested-by: Petr Machata <petrm@mellanox.com>
Reviewed-by: Petr Machata <petrm@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/saeed/linux
Saeed Mahameed says:
====================
mlx5-updates-2017-06-27 (Innova IPsec offload support)
This patchset adds support for Innova IPSec network interface card.
About Innova device:
--------------------
Innova is a network card with a ConnectX chip and an FPGA chip as a
bump-on-the-wire.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ I2C | | SBU | | +------+
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | Flash |
+-----+ +-------+
The FPGA synthesized logic is loaded from dedicated flash storage and has
access to its own dedicated DDR RAM.
The ConnectX chip firmware programs the FPGA by accessing its configuration
space over either the slow internal I2C link or the high-speed internal link.
The FPGA logic is divided into a "Shell" and a "Sandbox Unit" (SBU).
mlx5_core driver (with CONFIG_MLX5_FPGA) handles all shell functionality,
while other components may handle the various SBU functionalities.
The driver opens high-speed reliable communication channels with the shell and
the SBU over the internal link.
These channels may be used for high-bandwidth configuration or for SBU-specific
out-of-band data paths.
About Innova IPSec device:
--------------------------
Innova IPSec is a network card that allows offloading IPSec cryptography operations
from the host CPU to the NIC. It is an Innova card with an IPSec SBU.
The hardware keeps the database of IPSec Security Associations (SADB) in the FPGA's
DDR memory.
Internal
+----------+ Link +-----------------+
| +--------------+ FPGA | +------+
| ConnectX | | Shell +--+ QSFP |
| +--------------+ +-------+ | | Port |
+----------+ Internal I2C | | IPSec | | +------+
| | SBU | |
| +-------+ |
+--+----------+---+
| |
+--+--+ +---+---+
| DDR | | |
| | | Flash |
|SADB | | |
+-----+ +-------+
Modes and ciphers:
Currently the following modes and ciphers are supported:
IPv4 and IPv6
ESP tunnel and transport modes
AES 128 and 256 bit encryption, with GCM authentication (RFC4106)
IV is generated using seqiv, in sync with Linux's geniv.
More modes and ciphers may be added later.
Notes:
In the future similar functionality will be included in a single-chip NIC.
About the driver:
-----------------
Patches 1-4 prepare some existing driver code for the new feature:
* Add support for reserved GIDs in the hardware GID table
* Allow multiple modules to enable hardware RoCE support independently
Patches 5-6 define structs and helper functions for QP work-queues.
Patches 7-11 add various FPGA-related features required for Innova.
IPSec.
Patch 12 adds abstraction layer for Mellanox IPSec-offload capable devices.
atches 13-16 add IPSec offload support to the mlx5 netdevice.
This driver services the new IPSec offload API introduced in commit
d77e38e612a0 ("xfrm: Add an IPsec hardware offloading API")
Configuration Path:
If Innova IPSec device is detected, the mlx5e netdevice gets the new
NETIF_F_HW_ESP feature and the xdo callbacks, indicating ESP offload
capabilities, and also the matching TX checksum and GSO features.
The driver configures offloaded Security Associations (SAs) by sending
an ADD_SA or DEL_SA message to the IPSec SBU, which updates the SADB in DDR.
These messages and their responses are sent over a high-speed channel.
Counters for ethtool are retrieved by the driver from the SBU.
Data path:
On receive path, the SBU decrypts ESP packets which match the offloaded SADB,
but keeps them encapsulated.
The SBU injects metadata (Mellanox owned ethertype) indicating that crypto-offload
has taken place, the SA with which it was done, and the authentication result.
The ConnectX chip performs RX checksum offload on the packet, and RSS using the
ESP SPI value. The driver detects the special ethertype, and attaches a struct
secpath to the RX SKB, including flags to indicate that crypto offload took place,
the authentication result, and which xfrm_state was used for decryption, in the
olen and ovec members. The RX SKB may have useful CHECKSUM_COMPLETE. A separate
patchset will add support for that in the xfrm stack.
On transmit path, the stack encapsulates the packet but does not encrypt it, and
indicates in the SKB's secpath that crypto offload is to be performed and the SA
to use to do so.
The driver avoids performing crypto-offload for ESP fragments, and packets with
IP options, as the SBU cannot currently do that. For eligible packets, the driver
prepends a special ethertype with metadata instructing the hardware to perform crypto offload.
The stack builds regular (non-GSO) SKBs so that they contain a placeholder for the ESP trailer.
The driver trims it off, because the SBU automatically appends the trailer for offloaded packets.
The ConnectX chip performs TX checksum offload on inner UDP or TCP packets,
and GSO for TCP packets (duplicating the prepended metadata).
The segmented packets then undergo encryption in the SBU before going on the wire.
Performance:
We measure single stream of TCP on Intel(R) Xeon(R) CPU E5-2643 v2 @3.50GHz
Using AES-NI with ESP GSO we get constant 4.1 Gbps.
Using crypto offload we get constant 18 Gbps.
Note that these numbers require CHECKSUM_COMPLETE support in XFRM, which we submit separately.
- Ilan Tayari
====================
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Trivial fix to spelling mistake in mlx4_dbg debug message
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Acked-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add Innova IPSec SBU counters to the ethtool -S stats.
Add IPSec offload error counters to the ethtool -S stats.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Reviewed-by: Boris Pismenny <borisp@mellanox.com>
Reviewed-by: Gal Pressman <galp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
|
In the TX data path, prepend a special metadata ethertype which
instructs the hardware to perform cryptography.
In addition, fill Software-Parser segment in TX descriptor so
that the hardware may parse the ESP protocol, and perform TX
checksum offload on the inner payload.
Support GSO, by providing the inverse of gso_size in the metadata.
This allows the FPGA to update the ESP header (seqno and seqiv) on the
resulting packets, by calculating the packet number within the GSO
back from the TCP sequence number.
Note that for GSO SKBs, the stack does not include an ESP trailer,
unlike the non-GSO case.
Signed-off-by: Ilan Tayari <ilant@mellanox.com>
Signed-off-by: Yossi Kuperman <yossiku@mellanox.com>
Signed-off-by: Yevgeny Kliteynik <kliteyn@mellanox.com>
Signed-off-by: Boris Pismenny <borisp@mellanox.com>
Signed-off-by: Saeed Mahameed <saeedm@mellanox.com>
|
