| Age | Commit message (Collapse) | Author |
|---|
|
This patch replaces GFP_KERNEL by GFP_ATOMIC to avoid sleeping in the
ndo_set_rx_mode() call which is called with BH disabled.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When calling mvpp2_prs_mac_multi_set() from mvpp2_prs_mac_init(), two
parameters (the port index and the table index) are inverted. Fixes
this.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch fixes a typo in the mvpp2_prs_tcam_data_cmp() function, as
the shift value is inverted with the data.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When Tx IRQs are used, txq_bufs_free() can be called from both the Tx
path and from NAPI poll(). This led to CPU stalls as if these two tasks
(Tx and Poll) are scheduled on two CPUs at the same time, DMA unmapping
operations are done on the same txq buffers.
This patch adds a check not to call txq_done() from the Tx path if Tx
interrupts are used as it does not make sense to do so.
Fixes: edc660fa09e2 ("net: mvpp2: replace TX coalescing interrupts with hrtimer")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO header buffers are coming from a per cpu pool and should not
be unmapped as they are reused. The PPv2 driver was unmapping all
descriptors buffers unconditionally. This patch fixes this by checking
the buffers dma addresses before unmapping them, and by not unmapping
those who are located in the TSO header pool.
Fixes: 186cd4d4e414 ("net: mvpp2: software tso support")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
TSO headers are managed with txq index and therefore should be aligned
with the txq size, not with the aggregated txq size.
Fixes: 186cd4d4e414 ("net: mvpp2: software tso support")
Reported-by: Marc Zyngier <marc.zyngier@arm.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Just simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On Armada 7K/8K we need to explicitly enable the bus clock. The bus clock
is optional because not all the SoCs need them but at least for Armada
7K/8K it is actually mandatory.
The binding documentation is updating accordingly.
Signed-off-by: Gregory CLEMENT <gregory.clement@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch stops the internal MAC Tx clock from being enabled as the
internal clock isn't used. The definition used for the bit controlling
this behaviour is renamed as well as it was wrongly named (bit 4 of
GMAC_CTRL_2_REG).
Fixes: 3919357fb0bb ("net: mvpp2: initialize the GMAC when using a port")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The private port_list array has a list of pointers to mvpp2_port
instances. This list is allocated given the number of ports enabled in
the device tree, but the pointers are set using the port-id property. If
on a single port is enabled, the port_list array will be of size 1, but
when registering the port, if its id is not 0 the driver will crash.
Other crashes were encountered in various situations.
This fixes the issue by using an index not equal to the value of the
port-id property.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Yan Markman <ymarkman@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Parsing fragmentation detection failed due to wrong configured
parser TCAM entry's. Some traffic was marked as fragmented in RX
descriptor, even it wasn't IP fragmented. The hardware also failed to
calculate checksums which lead to use software checksum and caused
performance degradation.
Fixes: 3f518509dedc ("ethernet: Add new driver for Marvell Armada 375 network unit")
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use setup_timer function instead of initializing timer with the
function and data fields.
Signed-off-by: Allen Pais <allen.lkml@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove a goto in the PPv2 tx function which jumps to the next line
anyway. This is a cosmetic commit.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
When using a mac address described in the device tree, a check is made
to see if it is valid. When it's not, no fallback is defined. This
patches tries to get the mac address from h/w (or use a random one if
the h/w one isn't valid) when the dt mac address isn't valid.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC retrieval logic is using a variable to store an h/w stored mac
address and checks this mac against invalid ones before using it. But
the mac address is only read from h/w when using PPv2.1. So when using
PPv2.2 it defaults to its init state.
This patches fixes the logic to only check if the h/w mac is valid when
actually retrieving a mac from h/w.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MAC retrieval has a quite complicated logic (which is broken). Moves
it to its own function to prepare for patches fixing its logic, so that
reviews are easier.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mvneta driver and hardware supports IPv6 offload, however it
isn't enabled. Set the NETIF_F_IPV6_CSUM feature to inform the
network layer that this driver can offload IPV6 TCP and UDP
checksums. This change has been tested on an Armada 370 and the
feature support confirmed with several device datasheets
including the Armada XP and Armada 3700.
Signed-off-by: Andrew Pilloud <andrewpilloud@igneoussystems.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds the GoP link interrupt support for when a port isn't
connected to a PHY. Because of this the phylib callback is never called
and the link status management isn't done. This patch use the GoP link
interrupt in such cases to still have a minimal link management. Without
this patch ports not connected to a PHY cannot work.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is not necessarily a PHY between the GoP and the physical port.
However, the driver currently makes the "phy" property mandatory,
contrary to what is stated in the device tree bindings. This patch makes
the PHY optional, and aligns the PPv2 driver on its device tree
documentation. However if a PHY is provided, the GoP link interrupt
won't be used.
With this patch switches directly connected to the serdes lanes and SFP
ports on the Armada 8040-db and Armada 7040-db can be used if the link
interrupt is described in the device tree.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Convert all RGMII checks to use the phy_interface_mode_is_rgmii()
helper. This is a cosmetic patch.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds logic to reconfigure the comphy/GoP/MAC when the link
state is updated at runtime. This is very useful on boards where many
link speed are supported: depending on what is negotiated the PPv2
driver will automatically reconfigures the link between the PHY and the
MAC.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the link status changes, the phylib calls the link_event function
in the mvpp2 driver. Before this patch only the egress/ingress transmit
was enabled/disabled. This patch adds more functionality to the link
status management code by enabling/disabling the port per-cpu
interrupts, and the port itself. The queues are now stopped as well, and
the netif carrier helpers are called.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The link_event function is somewhat complicated. This cosmetic patch
simplifies it.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On some platforms, the comphy is between the MAC GoP and the PHYs. The
mvpp2 driver currently relies on the firmware/bootloader to configure
the comphy. As a comphy driver was added to the generic PHY framework,
this patch uses it in the mvpp2 driver to configure the comphy at boot
time to avoid relying on the bootloader.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The mac address is only retrieved from h/w when using PPv2.1. Otherwise
the variable holding it is still checked and used if it contains a valid
value. As the variable isn't initialized to an invalid mac address
value, we end up with random mac addresses which can be the same for all
the ports handled by this PPv2 driver.
Fixes this by initializing the h/w mac address variable to {0}, which is
an invalid mac address value. This way the random assignation fallback
is called and all ports end up with their own addresses.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 2697582144dd ("net: mvpp2: handle misc PPv2.1/PPv2.2 differences")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MVPP22_XLG_CTRL1_FRAMESIZELIMIT define is used as an offset, but is
defined as BIT(0). Updated its name to contains "OFFS" as in offset and
fix its value using the offset value, 0.
Reported-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Fixes: 76eb1b1de5b6 ("net: mvpp2: set maximum packet size for 10G ports")
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
txq_reclaim() does the normal transmit queue reclamation and
rxq_deinit() does the RX ring cleanup, none of these are packet drops,
so use dev_consume_skb() for both locations.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch uses the tso API to implement the tso functionality in Marvell
PPv2 driver.
Using iperf and 10G ports, using TSO shows a significant performance
improvement by a factor 2 to reach around 9.5Gbps in TX; as well as a
significant CPU usage drop (from 25% to 15%).
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The txq size is defined by MVPP2_AGGR_TXQ_SIZE, which is sometime not
used directly but through variables. As it is a fixed value use the
define everywhere in the driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The TSO header size was defined in many drivers. Factorize the code and
define its size in net/tso.h.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The patch adds GoP (group of ports) initialization functions. The mvpp2
driver was relying on the firmware/bootloader initialization; this patch
moves this setup to the mvpp2 driver.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Set maximum packet size for XLG 10G ports. Missing maximum packet size
for XLG configuration will cause kernel panic if oversized packet is
received by port.
Signed-off-by: Stefan Chulski <stefanc@marvell.com>
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a routine to initialize the XLG MAC at the port level when
using a port and the XAUI/10GKR interface mode. This wasn't done until
this commit, and the mvpp2 driver was relying on the bootloader/firmware
initialization. This doesn't mean everything is configured in the mvpp2
driver now, but it helps reducing the gap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This adds a routine to initialize the GMAC at the port level when using
a port. This wasn't done until this commit, and the mvpp2 driver was
relying on the bootloader/firmware initialization. This doesn't mean
everything is configured in the mvpp2 driver now, but it helps reducing
the gap.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This moves the mii configuration in the ndo_open path, to allow handling
different mii configurations later and to switch between these
configurations at runtime.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The macro defining the bit to toggle to bypass or not the
synchronization module is wrongly named. Writing 1 will disable bypass.
This patch s/MVPP22_CTRL4_SYNC_BYPASS/MVPP22_CTRL4_SYNC_BYPASS_DIS/.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Cosmetic patch to use the same formatting rules on all register
definitions.
Signed-off-by: Antoine Tenart <antoine.tenart@free-electrons.com>
Tested-by: Marcin Wojtas <mw@semihalf.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Stephen Hemminger <stephen@networkplumber.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This commit adds the support for two related features:
- Support for TX interrupts, with one interrupt for each CPU
- Support for different RX queue distribution modes
MVPP2_QDIST_SINGLE_MODE where a single interrupt, shared by all
CPUs, receives the RX events, and MVPP2_QDIST_MULTI_MODE, where the
per-CPU interrupts used for TX events are also used for RX events.
Since additional interrupts are needed, an update to the Device Tree
binding is needed. However, backward compatibility is preserved with
the old Device Tree binding, by gracefully degrading to the original
behavior, with only one RX interrupt, and TX completion being handled
by an hrtimer.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to the introduction of TX interrupts and improved RX
queue distribution, this commit introduces the concept of "queue
vector". A queue vector represents a number of RX and/or TX queues,
and an associated NAPI instance and interrupt.
This commit currently only creates a single queue_vector, so there are
no changes in behavior, but it paves the way for additional
queue_vector in the next commits.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The PPv2.2 IP has a concept of "software thread", with all registers
of the PPv2.2 mapped 8 times, for concurrent accesses by 8 "software
threads". In addition, interrupts on RX queues are associated to such
"software thread".
For most cases, we map a "software thread" to the more conventional
concept of CPU, but we will soon have one exception: we will have a
model where we have one TX interrupt per CPU (each using one software
thread), and all RX events mapped to another software thread
(associated to another interrupt).
In preparation for this change, it makes sense to change the naming
from MVPP2_MAX_CPUS to MVPP2_MAX_THREADS, and plan for 8 software
threads instead of 4 currently.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the global variables rxq_number and txq_number hold the
number of per-port TXQs and RXQs. Until now, such numbers were
constant regardless of the driver configuration. As we are going to
introduce different modes for TX and RX queues, these numbers will
depend on the configuration (PPv2.1 vs. PPv2.2, exact queue
distribution logic).
Therefore, as a preparation, we move the number of RXQs and TXQs in
the 'struct mvpp2_port' structure, next to the RXQs and TXQs
descriptor arrays.
For now, they remain initialized to the same default values as
rxq_number/txq_number used to be initialized, but this will change in
future commits.
The only non-mechanical change in this patch is that the check to
verify hardware constraints on the number of RXQs and TXQs is moved
from mvpp2_probe() to mvpp2_port_probe(), since it's now in
mvpp2_port_probe() that we initialize the per-port count of RXQ and
TXQ.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The RX queue group allocation is anyway re-done later in
mvpp2_port_init(), so resetting it in mvpp2_init() is not very useful,
and will be annoying as we are going to rework the RX queue group
allocation logic.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The MVPP21_ISR_RXQ_GROUP_REG register is not indexed by rxq, but by
port, so we fix the parameter name accordingly. There are no
functional changes.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
of_irq_to_resource() has recently been fixed to return negative error #'s
along with 0 in case of failure, however the Marvell MV643xx Ethernet
driver still only regards 0 as invalid IRQ -- fix it up.
Fixes: 7a4228bbff76 ("of: irq: use of_irq_get() in of_irq_to_resource()")
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When all a function does is calling another function with the exact same
arguments, in the exact same order, you know it's time to remove said
function. Which is exactly what this commit does.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This function is not used in the driver, remove it.
Signed-off-by: Thomas Petazzoni <thomas.petazzoni@free-electrons.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
