| Age | Commit message (Collapse) | Author |
|---|
|
The ndo_set_rx_mode() and ndo_add/del_vxlan_port() calls may be called with
BHs disabled. The driver currently issues the required cmds to the FW in
these contexts and polls on completions from the FW, while BHs remain
disabled. This can cause either packet loss or packet reception to be
delayed on that CPU.
This patch defers processing of the above cmds to a separate workqueue.
With this change, FW cmds are now issued only in process context.
Now that the FW cmds are issued only in process context, they can sleep
waiting for a completion instead of polling. All the spin_lock_bh(mcc_lock)
calls are now replaced with mutex calls.
Also a new rx_filter_lock is now needed to protect the RX filtering fields
like vids[] between be_vlan_add/rem_vid() and __be_set_rx_mode() contexts.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Eachtime the ndo_set_rx_mode() routine is called, the driver programs the
multicast list in the adapter without checking if there are any changes to
the list. This leads to a flood of RX_FILTER cmds when a number of vlan
interfaces are configured over the device, as the ndo_ gets
called for each vlan interface. To avoid this, we now use __dev_mc_sync()
and __dev_uc_sync() API, but only to detect if there is a change in the
mc/uc lists. Now that we use this API, the code has to be-designed to
issue these API calls for each invocation of the be_set_rx_mode() call.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently removes a new vid from the adapter->vids[] array if
be_vid_config() returns an error, which occurs when there is an error in
HW/FW. This is wrong. After the HW/FW error is recovered from, we need the
complete vids[] array to re-program the vlan list.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Lancer FW has a bug due to which in some cases vlan-promisc setting
is cleared eventhough the vlan-list programming did not succeed (via
VLAN_CONFIG) cmd. The driver has no way of knowing if the vlan-promisc
mode was cleared or not when this cmd fails. To work around this issue,
this patch first explicitly clears the vlan-promisc mode via RX_FILTER
cmd and then tries to program the vlan list.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The be2net driver performs fw temperature queries on be_worker() routine,
which is executed each second for each be_adapter. There is a frequency
threshold to avoid fw query to happens at each call to be_worker();
instead, currently a fw query occurs once in 64 runs of the procedure.
Nevertheless, this fw temperature query is invoked only for adapters which
interface is up, so we can see I/O errors on read of hwmon counters from
userspace (from tools like lm-sensors) in case we have adapters' functions
which interface is down.
This patch moves the fw query code to be invoked even if interface is down.
No functional changes were introduced.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
"num_vec" needs to be signed for the error handling to work.
Fixes: e261768e9e39 ('be2net: support asymmetric rx/tx queue counts')
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch updates year and company name in the copyright markings in the
be2net source files.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On SR-IOV profiles, when the user connects a Linux Bridge or OVS to a BE3
vport, they suffer the "broadcast/multicast echo" problem. BE3 EVB echoes
broadcast and multicast packets back to PF's vport confusing the
Linux bridge. BE3 relies on the src-mac addr being programmed on the
interface to avoid sending back an echo of a broadcast or multicast packet
on a vPort. When a Linux bridge is connected to a BE3, the mac-addr of the
VM behind the bridge doesn't get configured on the vPort and so echo
cancellation doesn't work.
This patch worksaround this problem by disabling the EVB initially
and re-enabling it *only* when SR-IOV is enabled by the user. For the
driver fix to work, the BE3 FW version must be >= 11.1.84.0.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be2net so far supported creation of RX/TX queues only in pairs.
On configs where rx and tx queue counts are different, creation of only
the lesser number of queues has been supported.
This patch now allows a combination of RX/TX-only channels along with
combined channels. N TX-queues and M RX-queues can be created with the
following cmds:
ethtool -L ethX combined N rx M-N (when N < M)
ethtool -L ethX combined M tx N-M (when M < N)
Setting both RX-only and TX-only channels is still not supported.
It is mandatory to create atleast one combined channel.
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EQs available on a function are shared between NIC and RoCE.
The be_max_eqs() macro was so far being used to refer to the max number of
EQs available for NIC. This has caused some confusion in the code. To fix
this confusion this patch introduces a new macro called be_max_nic_eqs()
to refer to the max number of EQs avialable for NIC only and renames
be_max_eqs() to be_max_func_eqs().
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This change replaces the network device operations for adding or removing a
VXLAN port with operations that are more generically defined to be used for
any UDP offload port but provide a type. As such by just adding a line to
verify that the offload type if VXLAN we can maintain the same
functionality.
I have also gone though and removed the BE2NET_VXLAN config option since it
no longer relies on the VXLAN code anyway.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we do not distribute queue resources to enable RSS for VFs
in multi-channel/partition configurations.
Fix this by having each PF(SRIOV capable) calculate it's share of the
15 RSS Policy Tables available per port before provisioning resources for
all the VFs.
This proportional share calculation is done based on division of the
PF's MAX VFs with the Total MAX VFs on that port. It also needs to
learn about the no: of NIC PFs on the port and subtract that from
the 15 RSS Policy Tables on the port.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk does support wake-up from ACPI shutdown state - S5, provided the
platform supports it (like Auxiliary power source etc). The changes listed
below are done to fix this.
1) There's no need to defer the HW configuration of WOL to be_suspend().
Remove this in be_suspend() and move it to be_set_wol() ethtool function
so it is configured directly in the context of ethtool. This automatically
takes care of the shutdown case.
2) The driver incorrectly uses WOL_CAP field in the FW response to
get_acpi_wol_cap() command, to determine if WOL is enabled. Instead the
driver must rely on the macaddr field in the response to infer WOL state.
3) In be_get_config() during init, if we find that WOL is enabled in FW,
call pci_enable_wake() to enable pmcsr.pme_en bit. This is needed to
support persistent WOL configuration provided by the FW in some platforms.
4) Remove code in be_set_wol() that writes to PCICFG_PM_CONTROL_OFFSET
to set pme_en bit; pci_enable_wake() sets that.
Fixes: 028991e49 ("Enabling Wake-on-LAN is not supported in S5 state")
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PF driver provisions resources for VFs, it currently only looks
at max RSS queues available to calculate the number of VF queue pairs.
This logic breaks when there are less number of TX-queues than RSS-queues.
This patch fixes this problem by using the max-TXQs available in the
PF-pool in the calculations. As a part of this change the
be_calculate_vf_qs() routine is renamed as be_calculate_vf_res() and the
code that calculates limits on other related resources is moved here to
contain all resource calculation code inside one routine.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be_open calls down to functions which expects rtnl lock to be held.
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The adapter->pcicfg resource is either mapped via pci_iomap() or
derived from adapter->db. During be_remove() this resource was ignored
and so could remain mapped after remove.
Add a flag to track whether adapter->pcicfg was mapped or not, then
use that flag in be_unmap_pci_bars() to unmap if required.
Fixes: 25848c901 ("use PCI MMIO read instead of config read for errors")
Signed-off-by: Douglas Miller <dougmill@linux.vnet.ibm.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the interface is opened (in be_open()) the routine
be_enable_if_filters() must be called to switch on the basic filtering
capabilities of an interface that are not changed at run-time.
These include the flags UNTAGGED, BROADCAST and PASS_L3L4_ERRORS.
Other flags such as MULTICAST and PROMISC must be enabled later by
be_set_rx_mode() based on the state in the netdev/adapter struct.
be_enable_if_filters() routine is wrongly trying to enable MULTICAST flag
without checking the current adapter state. This can cause the RX_FILTER
cmds to the FW to fail. This patch fixes this problem by only enabling
the basic filtering flags in be_enable_if_filters().
The VF must be able to issue RX_FILTER cmd with any filter flag, as long
as the PF allowed those flags (if_cap_flags) in the iface it provisioned
for the VF. This rule is applicable even when the VF doesn't have the
FILTMGMT privilege. There is a bug in BE3 FW that wrongly fails RX_FILTER
multicast programming cmds on VFs that don't have FILTMGMT privilege.
This patch also helps in insulating the VF driver from be_open failures due
to the FW bug. A fix for the BE3 FW issue will be available in
versions >= 11.0.283.0 and 10.6.334.0
Reported-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In QnQ configurations like Flex-10 where the VLANs are inserted by the
ASIC, on rare occasions the HW is encountering a scenario where the
final frame length ends to be greater than what the ASIC can support.
This is because when the TXULP pulls the TX WRB to check the length
of the frame to be transmitted it also adds the size of VLANs to be
inserted by the HW to the length of the frame indicated in the WRB,
which in some cases fails the range check. This causes a UE.
Avoid this by trimming the skb length to accommodate the VLAN insertion.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When 16-bit integers are loaded on CPUs with high order native
register sizes, the CPU could use some extra ops before using them.
And currently some of the frequently used fields in the driver like
the producer and consumer indices of the queues are declared as u16.
This patch declares such fields as u32. With this change we see the
64-byte packets per second numbers improve by about 4%.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupts registered by RoCE driver are not unregistered when
msix interrupts are disabled during error recovery causing a
crash. Detach the adapter instance from RoCE driver when error
is detected to complete the cleanup. Attach the driver again after
the adapter is recovered from error.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The EVB (virtual bridge) functionality should be disabled on older BE3
and Lancer chips if SR-IOV is disabled in the NIC's BIOS. This setting
is identified by the zero value of total VFs reported by the card.
The GET_HSW_CONFIG command cannot be used as it is not supported by
these older chipset's FW.
v2: added the comment
Cc: Sathya Perla <sathya.perla@broadcom.com>
Cc: Ajit Khaparde <ajit.khaparde@broadcom.com>
Cc: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Cc: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Cc: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Acked-by: Sathya Perla <sathya.perla@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
async event
>From FW version 11.0. onwards, the PORT_MISCONFIG event generated by the FW
will carry more information about the event in the "data_word1"
and "data_word2" fields. This patch adds support in the driver to parse the
new information and log it accordingly. This patch also changes some of the
messages that are being logged currently.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@broadcom.com>
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently we request RSS capability even if a single Rx ring is created.
As a result in few cases we unnecessarily consume an RSS capable interface
which is a limited resource in the chip.
This patch enables RSS on an interface only if more than one Rx ring
is created.
Signed-off-by: Ajit Khaparde <ajit.khaparde@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Interrupt moderation parameters need to be recalculated only
after a time interval of 1 ms. Interval calculation is wrong
when there is a rollover of jiffies. Using recommended way of interval
calculation using jiffies to fix this.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Retry error recovery MAX_ERR_RECOVERY_RETRY_COUNT times in case of
failure during error recovery.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
After error is detected, wait for adapter to move to ready state
before destroying queues and cleanup of other resources. Also
skip performing any cleanup for non-Lancer chips and move debug
messages to correct routine.
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CMD_SUBSYSTEM_LOWLEVEL cmds need DEV_CFG Privilege to run
which VFs don't have by default.
Self-tests need to be issued only for PFs.
Signed-off-by: Somnath Kotur <somnath.kotur@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SRIOV resource distribution logic for RX/TX queue counts is not optimal
when a small number of VFs are enabled. It does not take into account the
VF's EQ count while computing the queue counts. Because of this, the VF
gets a large number of queues, though it doesn't have sufficient EQs,
resulting in wasted queue resources. And the PF gets a smaller share of
queues though it has more EQs. Fix this by capping the VF queue count at
its EQ count.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver decrements its vlan count without checking if it is really
present in its list. This results in an invalid vlan count and impacts
subsequent vlan add/rem ops. The function be_vlan_rem_vid() should be
updated to fix this.
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver currently logs the message "VF is not privileged to issue
opcode" by checking only the base_status field for UNAUTHORIZED_REQUEST.
Add check to look for INSUFFICIENT_PRIVILEGES in the additional status
field also as not all cmds fail with that base status.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be_set_phys_id() returns 0 to ethtool when the command fails in the FW.
This patch fixes the set_phys_id() to return -EIO in case the FW cmd fails.
Signed-off-by: Suresh Reddy <suresh.reddy@broadcom.com>
Signed-off-by: Sriharsha Basavapatna <sriharsha.basavapatna@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Pull networking fixes from David Miller:
1) Prevent XFRM per-cpu counter updates for one namespace from being
applied to another namespace. Fix from DanS treetman.
2) Fix RCU de-reference in iwl_mvm_get_key_sta_id(), from Johannes
Berg.
3) Remove ethernet header assumption in nft_do_chain_netdev(), from
Pablo Neira Ayuso.
4) Fix cpsw PHY ident with multiple slaves and fixed-phy, from Pascal
Speck.
5) Fix use after free in sixpack_close and mkiss_close.
6) Fix VXLAN fw assertion on bnx2x, from Yuval Mintz.
7) natsemi doesn't check for DMA mapping errors, from Alexey
Khoroshilov.
8) Fix inverted test in ip6addrlbl_get(), from ANdrey Ryabinin.
9) Missing initialization of needed_headroom in geneve tunnel driver,
from Paolo Abeni.
10) Fix conntrack template leak in openvswitch, from Joe Stringer.
11) Mission initialization of wq->flags in sock_alloc_inode(), from
Nicolai Stange.
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net: (35 commits)
sctp: sctp should release assoc when sctp_make_abort_user return NULL in sctp_close
net, socket, socket_wq: fix missing initialization of flags
drivers: net: cpsw: fix error return code
openvswitch: Fix template leak in error cases.
sctp: label accepted/peeled off sockets
sctp: use GFP_USER for user-controlled kmalloc
qlcnic: fix a loop exit condition better
net: cdc_ncm: avoid changing RX/TX buffers on MTU changes
geneve: initialize needed_headroom
ipv6: honor ifindex in case we receive ll addresses in router advertisements
addrconf: always initialize sysctl table data
ipv6/addrlabel: fix ip6addrlbl_get()
switchdev: bridge: Pass ageing time as clock_t instead of jiffies
sh_eth: fix 16-bit descriptor field access endianness too
veth: don’t modify ip_summed; doing so treats packets with bad checksums as good.
net: usb: cdc_ncm: Adding Dell DW5813 LTE AT&T Mobile Broadband Card
net: usb: cdc_ncm: Adding Dell DW5812 LTE Verizon Mobile Broadband Card
natsemi: add checks for dma mapping errors
rhashtable: Kill harmless RCU warning in rhashtable_walk_init
openvswitch: correct encoding of set tunnel action attributes
...
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds support for ethtool's --get-dump option in be2net,
to retrieve FW dump. In the past when this option was not yet available,
this feature was supported via the --register-dump option as a workaround.
This patch removes support for FW-dump via --register-dump option as it is
now available via --get-dump option. Even though the
"ethtool --register-dump" cmd which used to work earlier, will now fail
with ENOTSUPP error, we feel it is not an issue as this is used only
for diagnostics purpose.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 72ef3a88fa8e ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd") passed a specific pf_num while issuing a
GET_PROFILE_CONFIG cmd as FW returns descriptors for all functions when
pf_num is zero. But, when pf_num is set to a non-zero value, FW does not
return the Port resource descriptor.
This patch fixes this by setting pf_num to 0 while issuing the query cmd
and adds code to pick the correct NIC resource descriptor from the list of
descriptors returned by FW.
Fixes: 72ef3a88fa8e ("be2net: set pci_func_num while issuing
GET_PROFILE_CONFIG cmd")
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
eeh_error, fw_timeout, hw_error variables in the be_adapter structure are
not used anymore. An earlier patch that introduced adapter->err_flags to
store this information missed removing these variables.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch removes a line of code that changes adapter->recommended_prio
value followed by yet another assignment.
Also, the variable is used to store the vlan priority value that is already
shifted to the PCP bits position in the vlan tag format. Hence, the name of
this variable is changed to recommended_prio_bits.
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
(based on a jumper setting on the adapter.) In this mode, the FW image when
flashed is authenticated with a digital signature. This patch logs
appropriate error messages and return a status to ethtool when errors
relating to FW image authentication occur.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
All code relating to FW cmds is in be_cmds.[ch] excepting FW flash cmd
related code. This patch moves these routines from be_main.c to be_cmds.c
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Many constant definitions relating to the FW-image layout
(such as section offset values) were defined in decimal format rather than
hexa-decimal. This makes this part of the code un-readable. Also some
defines related to BE2 are labeld "g2" and defines related to BE3 are
labeled "g3". This patch cleans up all of this to make this code more
readable.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BE3 chip doesn't support VEPA mode.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The VF link state setting transition from "disable" to "auto" does not work
due to a bug in SET_LOGICAL_LINK_CONFIG_V1 cmd in FW. This issue could not
be fixed in FW due to some backward compatibility issues it causes with
some released drivers. The issue has been fixed by introducing a new
version (v2) of the cmd from 10.6 FW onwards. In v2, to set the VF link
state to auto, both PLINK_ENABLE and PLINK_TRACK bits have to be set to 1.
The VF link state setting feature now works on Lancer chips too from
FW ver 10.6.315.0 onwards.
Signed-off-by: Suresh Reddy <suresh.reddy@avagotech.com>
Signed-off-by: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Recently Dough Ledford reported a deadlock happening
between ocrdma-load sequence and NetworkManager service
issueing "open" on be2net interface.
The deadlock happens when any be2net hook (e.g. open/close) is called
in parallel to insmod ocrdma.ko.
A. be2net is sending administrative open/close event to ocrdma holding
device_list_mutex. It does this from ndo_open/ndo_stop hooks of be2net.
So sequence of locks is rtnl_lock---> device_list lock
B. When new ocrdma roce device gets registered, infiniband stack now
takes rtnl_lock in ib_register_device() in GID initialization routines.
So sequence of locks in this path is device_list lock ---> rtnl_lock.
This improper locking sequence causes deadlock.
In order to resolve the above deadlock condition, ocrdma intorduced a
patch to stop listening to administrative open/close events generated from
be2net driver. It now depends on link-state-change async-event generated from
CNA. This change leaves behind dead code which used to generate administrative
open/close events. This patch cleans-up all that dead code from be2net.
Reported-by: Doug Ledford <dledford@redhat.com>
CC: Sathya Perla <sathya.perla@avagotech.com>
Signed-off-by: Padmanabh Ratnakar <padmanabh.ratnakar@avagotech.com>
Signed-off-by: Selvin Xavier <selvin.xavier@avagotech.com>
Signed-off-by: Devesh Sharma <devesh.sharma@avagotech.com>
Signed-off-by: Doug Ledford <dledford@redhat.com>
|
|
When the first request_irq fails in be_msix_register, i value
would be zero. The current code decrements the i value and
accesses the eq object without validating the decremented
"i" value. This can cause an "invalid memory address access"
violation.
This patch fixes the problem by accessing the eq object after
validating the "i" value.
Signed-off-by: Venkat Duvvuru <venkatkumar.duvvuru@avagotech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The name NETIF_F_ALL_CSUM is a misnomer. This does not correspond to the
set of features for offloading all checksums. This is a mask of the
checksum offload related features bits. It is incorrect to set both
NETIF_F_HW_CSUM and NETIF_F_IP_CSUM or NETIF_F_IPV6 at the same time for
features of a device.
This patch:
- Changes instances of NETIF_F_ALL_CSUM to NETIF_F_CSUM_MASK (where
NETIF_F_ALL_CSUM is being used as a mask).
- Changes bonding, sfc/efx, ipvlan, macvlan, vlan, and team drivers to
use NEITF_F_HW_CSUM in features list instead of NETIF_F_ALL_CSUM.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We would like to automatically provide busy polling support
to all NAPI drivers, without them having to implement anything.
skb_mark_napi_id() can be called from napi_gro_receive() and
napi_get_frags().
Few drivers are still calling skb_mark_napi_id() because
they use netif_receive_skb(). They should eventually call
napi_gro_receive() instead. I will leave this to drivers
maintainers.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The lancer_cmd_get_file_len() uses lancer_cmd_read_object() to get
the current size of registers for ethtool registers dump. Returned status
value is stored but not checked. The check itself is not necessary as
the data_read output variable is initialized to 0 and status variable
can be removed.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
