| Age | Commit message (Collapse) | Author |
|---|
|
commit fba875591 ("disable TX in be_close()") disabled TX in be_close()
to protect be_xmit() from touching freed up queues in the AER recovery
flow. But, TX must be disabled *before* cleaning up TX completions in
the close() path, not after. This allows be_tx_compl_clean() to free up
all TX-req skbs that were notified to the HW.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible for some versions of firmware to advertise capabilities that driver
is not ready to handle. This may lead to controller stall. Since the driver is
interested only in subset of flags, clearing the rest.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware workaround requesting hardware to skip vlan insertion is necessary
only when umc or qnq is enabled. Enabling this workaround in other scenarios
could cause controller to stall.
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use standard PM state macros PCI_Dx instead of numeric 0/1/2..
Signed-off-by: Yijing Wang <wangyijing@huawei.com>
Cc: netdev@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be_find_vfs() is no longer needed as the common PCI calls provide the same
functionality.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/wireless/ath/ath9k/Kconfig
drivers/net/xen-netback/netback.c
net/batman-adv/bat_iv_ogm.c
net/wireless/nl80211.c
The ath9k Kconfig conflict was a change of a Kconfig option name right
next to the deletion of another option.
The xen-netback conflict was overlapping changes involving the
handling of the notify list in xen_netbk_rx_action().
Batman conflict resolution provided by Antonio Quartulli, basically
keep everything in both conflict hunks.
The nl80211 conflict is a little more involved. In 'net' we added a
dynamic memory allocation to nl80211_dump_wiphy() to fix a race that
Linus reported. Meanwhile in 'net-next' the handlers were converted
to use pre and post doit handlers which use a flag to determine
whether to hold the RTNL mutex around the operation.
However, the dump handlers to not use this logic. Instead they have
to explicitly do the locking. There were apparent bugs in the
conversion of nl80211_dump_wiphy() in that we were not dropping the
RTNL mutex in all the return paths, and it seems we very much should
be doing so. So I fixed that whilst handling the overlapping changes.
To simplify the initial returns, I take the RTNL mutex after we try
to allocate 'tb'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to set the coherent DMA mask only if dma_set_mask() succeeded, and to
error out if either fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge 'net' bug fixes into 'net-next' as we have patches
that will build on top of them.
This merge commit includes a change from Emil Goode
(emilgoode@gmail.com) that fixes a warning that would
have been introduced by this merge. Specifically it
fixes the pingv6_ops method ipv6_chk_addr() to add a
"const" to the "struct net_device *dev" argument and
likewise update the dummy_ipv6_chk_addr() declaration.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Added code to initiate FW dump via ethtool. Driver checks if the previous dump
has been cleared before initiating the dump. It doesn't initiate the dump
if it is not cleared.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During a PCI EEH/AER error recovery flow, if the device did not successfully
restart, the error_detected() hook may be called a second time with a
"perm_failure" state. This patch skips over driver cleanup for the second
invocation of the callback.
Also, Lancer error recovery code is fixed-up to handle these changes.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
HW does not compute L4 checksum for IP Fragmented packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For padded packets, Lancer computes incorrect checksum. The workaround is
to trim such packets. This workaround is mainly for IPv4 packets.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In Lancer, packets that are 32 bytes or less may cause a transmit stall.
The work-around is to pad such packets to a 36 byte length.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Removing the be_cmd_get_fw_ver() query from be_get_drvinfo() and invoking
the same from be_setup() and/or post firmware download.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Merge net into net-next because some upcoming net-next changes
build on top of bug fixes that went into net.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Refactor all TX HW workarounds into a separate routine called
be_xmit_workarounds().
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In function be_get_nic_desc(), it will go through the descriptor array
returned from f/w. By comparing the desc_type field, it determines whether
there is a nic descriptor in the array or not. In the case of no nic
descriptor, this function should return NULL.
The code may return an invalide descriptor, when there is no nic descriptor
in the array and the desc_count is less than MAX_RESOURCE_DESC. In this case,
even there is no nic descriptor, it will still return the lase descriptor
since the i doesn't equal to MAX_RESOURCE_DESC.
This patch fix this issue by returning the descriptor when find it and return
NULL for other cases.
Signed-off-by: Wei Yang <weiyang@linux.vnet.ibm.com>
Reviewed-by: Gavin Shan <shangw@linux.vnet.ibm.com>
Reviewed-by: Xiao Guangrong <xiaoguangrong@linux.vnet.ibm.com>
Acked-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix to avoid double insertion of vlan tags into the packet while
handling an asic workaroud (issue introduced by net next Commit bc0c340)
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
be_close() followed by be_clear() is called as a part of cleanup in the
EEH/AER flow. This patch stops TX in be_close() before cleaning/freeing
up the TX queues in be_clear(). This prevents be_xmit() from being called
while TX queues no longer exist.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While cleaning RX queues, the CQ DB may be rung several times (with rearm)
while waiting for the flush compl. Each CQ-notify with rearm can result in
an event. The EQ may get full resulting in a HW error.
Fix this by not re-arming the CQ while notifying a valid completion.
Also, there's no need to wait for 1ms after destroying RXQ, as the code in
be_rx_cq_clean() waits for the flush compl to arrive.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The buffer size for a FW cmd request must be big enough to fit the response,
else the cmd fails. For GET_MAC_LIST cmd, though the memory allocated for
the cmd is big enough to fit the response, the payload_len value in the
WRB hdr is being set to the request length only.
Fix this for GET_MAC_LIST cmd.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the PF driver calls pci_enable_sriov(), the VFs may be probed
inline before the call returns. So, the resources required for all VFs
must be provisioned by the PF driver *before* calling pci_enable_sriov();
else, VF probe will fail.
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
As per SPEC, INTx mode is not supported on VFs. So if enable_msix fails,
then just fail probe. Also bail out of be_open if irq_register fails.
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When RQ creation fails in be_open(), driver jumps to be_close() where
napi_disable() is done without a prior napi_enable(); leading to a hang.
This change is needed as there is no way to see if napi is enable/disabled.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Increasing the timeout value of write_object command to 60 seconds as
30 second timeout was found to be not enough for the command to complete.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
certain devices
When a user requests Promiscuous mode on SkyHawk-R devices,
the FW enables Desparate Promiscuous mode.
Due to this, we need to explicitly enable Multicast Promiscuous mode
so that Multicast packets are received as well.
This patch fixes that.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The tx priority pause count is available with the driver.
But we were not showing it.
This change should fix it and display it in ethtool stats.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Only BE devices provide 16-bit counter for rx_drops_no_fragment.
All other devices provide a 32-bit counter for this stat.
Use the 32-bit value where available.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
SkyHawk-R devices should use v2 of cq_create command.
BE3/BE2 devices can use version 0 of the command to create a CQ.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/broadcom/bnx2x/bnx2x_main.c
drivers/net/ethernet/emulex/benet/be.h
include/net/tcp.h
net/mac802154/mac802154.h
Most conflicts were minor overlapping stuff.
The be2net driver brought in some fixes that added __vlan_put_tag
calls, which in net-next take an additional argument.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Lancer FW requires that the first cmd issued by the host-driver be an FLR.
So, re-order be_probe() to move be_cmd_function_reset() ahead of
be_cmd_fw_init().
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-R requires V1 version of GET_FUNCTION_CONFIG cmd to be used for
querrying resources available per function.
Signed-off-by: Kalesh AP <kalesh.purayil@emulex.com>
Signed-off-by: Somnath Kotur <somnath.kotur@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
freeze.
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Suresh Reddy <suresh.reddy@emulex.com>
Signed-off-by: Sarveshwar Bandi <sarveshwar.bandi@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BE3 HW in UMC mode could wrongly double tag a packet with PVID
when the packet already has a inlined VLAN tag.
In UMC mode, When HW finds that a packet is already VLAN tagged
PVID should not be inserted into the packet.
To fix this use the FW hack to instruct the HW to skip PVID tagging.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ASIC could lockup in the transmit path when it tries
to insert VLAN in a specific ipv6 packet.
1) Identify the packet which can cause this.
2) Check if the firmware provides a workaround to prevent this.
3) If workaround is not present, drop the packet.
4) If the firmware provides a workaround, insert the VLAN tag in the
packet and inform the firmware to skip further VLAN insertions.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
To work-around a HW bug that corrupts certain packets while inserting
a pvid, the driver needs to invoke a special hack in firmware to avoid
the VLAN tagging in the HW. Since this logic is missing from the driver,
removing the check for pvid.
Signed-off-by: Ajit Khaparde <ajit.khaparde@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/emulex/benet/be_main.c
drivers/net/ethernet/intel/igb/igb_main.c
drivers/net/wireless/brcm80211/brcmsmac/mac80211_if.c
include/net/scm.h
net/batman-adv/routing.c
net/ipv4/tcp_input.c
The e{uid,gid} --> {uid,gid} credentials fix conflicted with the
cleanup in net-next to now pass cred structs around.
The be2net driver had a bug fix in 'net' that overlapped with the VLAN
interface changes by Patrick McHardy in net-next.
An IGB conflict existed because in 'net' the build_skb() support was
reverted, and in 'net-next' there was a comment style fix within that
code.
Several batman-adv conflicts were resolved by making sure that all
calls to batadv_is_my_mac() are changed to have a new bat_priv first
argument.
Eric Dumazet's TS ECR fix in TCP in 'net' conflicted with the F-RTO
rewrite in 'net-next', mostly overlapping changes.
Thanks to Stephen Rothwell and Antonio Quartulli for help with several
of these merge resolutions.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch sets the coherent DMA mask to 64-bit after the be2net driver has
been acknowledged that the system is 64-bit DMA capable. The coherent DMA
mask is examined by the Intel IOMMU driver to determine whether to allow
pass through context mapping for all devices. With this patch, the be2net
driver combined with be2net compatible hardware provides comparable
performance to the case where vt-d is disabled. The main use-case for this
change is to decrease the time necessary to copy virtual machine memory
during KVM live migration instantiations.
This patch was tested on a system that enables the IOMMU in non-coherent
mode. Two DMA remapper issues were encountered in the previous version and
both patches have been committed.
commit ea2447f700cab264019b52e2b417d689e052dcfd
commit 2e12bc29fc5a12242d68e11875db3dd58efad9ff
Signed-off-by: Craig Hada <craig.hada@hp.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use GET_PROFILE_CONFIG_V1 cmd for BE3-R, to query the maximum number of
TX rings available per function. On SH-R the same is queried via the
GET_FUNCTION_CONFIG cmd.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Avoid flashing BE3 UFI on BE3-R chip by verifying asic_revision
number of the chip.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't log "Out of MCCQ wrbs" msg. When the driver doesn't receive any
response from the FW it already logs a "FW not responding" message.
The driver runs out of MCCQ wrbs much later. Also, this message can
swamp the kernel log in HW/FW error scenarios.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Skyhawk-R and BE3-R (SuperNIC profile) require V2 version
of TXQ_CREATE cmd to be used.
Signed-off-by: Vasundhara Volam <vasundhara.volam@emulex.com>
Signed-off-by: Sathya Perla <sathya.perla@emulex.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add a protocol argument to the VLAN packet tagging functions. In case of HW
tagging, we need that protocol available in the ndo_start_xmit functions,
so it is stored in a new field in the skb. The new field fits into a hole
(on 64 bit) and doesn't increase the sks's size.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Change the rx_{add,kill}_vid callbacks to take a protocol argument in
preparation of 802.1ad support. The protocol argument used so far is
always htons(ETH_P_8021Q).
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Rename the hardware VLAN acceleration features to include "CTAG" to indicate
that they only support CTAGs. Follow up patches will introduce 802.1ad
server provider tagging (STAGs) and require the distinction for hardware not
supporting acclerating both.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver should use return value of __vlan_put_tag with appropriate
NULL-check instead of old skb pointer.
Signed-off-by: Ivan Vecera <ivecera@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
