Age | Commit message (Collapse) | Author |
|
Define ndo_features_check. Hw supports offload only for ipv4 inner and
ipv4 outer pkt.
Code refactor for setting inner tcp pseudo csum.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Defines enic_udp_tunnel_add/del for configuring vxlan tunnel offload.
enic supports offload of only one ipv4/udp port.
There are two modes that fw supports for vxlan offload.
mode 0: fcoe bit is set for encapsulated packet. fcoe_fc_crc_ok is set
if checksum of csum is ok. This bit is or of ip_csum_ok and
tcp_udp_csum_ok
mode 2: BIT(0) in rss_hash is set if it is encapsulated packet.
BIT(1) is set if outer_ip_csum_ok/
BIT(2) is set if outer_tcp_csum_ok
tcp_udp_csum_ok/ipv4_csum_ok is set if inner csum is OK.
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds devcmds needed for vxlan offload. Implement 3 new devcmd
overlay_offload_ctrl: enable/disable offload
overlay_offload_cfg: update offload udp port number
get_supported_feature_ver: get hw supported offload version. Each
version has different bitmap for csum_ok/encap
Signed-off-by: Govindarajulu Varadarajan <gvaradar@cisco.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do polling generically these days.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.
Fix all drivers with ndo_get_stats64 to have a void function.
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver sets the skb l4/l3 hash based on NIC_CFG_RSS_HASH_TYPE_*,
which is bit mask. This is wrong. Hw actually provides us enum.
Use CQ_ENET_RQ_DESC_RSS_TYPE_* to set l3 and l4 hash type.
Fixes: bf751ba802fe ("driver/net: enic: record q_number and rss_hash for skb")
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When MTU is changed from 9000 to 1500 while there is burst of inbound 9000
bytes packets, adaptor sometimes delivers 9000 bytes packets to 1500 bytes
buffers. This causes memory corruption and sometimes crash.
This is because of a race condition in adaptor between "RQ disable"
clearing descriptor mini-cache and mini-cache valid bit being set by
completion of descriptor fetch. This can result in stale RQ desc being
cached and used when packets arrive. In this case, the stale descriptor
have old MTU value.
Solution is to write RQ->disable twice. The first write will stop any
further desc fetches, allowing the second disable to clear the mini-cache
valid bit without danger of a race.
Also, the check for rq->running becoming 0 after writing rq->enable to 0
is not done properly. When incoming packets are flooding the interface,
rq->running will pulse high for each dropped packet. Since the driver was
waiting for 10us between each poll, it is possible to see rq->running = 1
1000 times in a row, even though it is not actually stuck running.
This results in false failure of vnic_rq_disable(). Fix is to try more
than 1000 time without delay between polls to ensure we do not miss when
running goes low.
In old adaptors rq->enable needs to be re-written to 0 when posted_index
is reset in vnic_rq_clean() in order to keep rq->prefetch_index in sync.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
et131x: min_mtu 64, max_mtu 9216
altera_tse: min_mtu 64, max_mtu 1500
amd8111e: min_mtu 60, max_mtu 9000
bnad: min_mtu 46, max_mtu 9000
macb: min_mtu 68, max_mtu 1500 or 10240 depending on hardware capability
xgmac: min_mtu 46, max_mtu 9000
cxgb2: min_mtu 68, max_mtu 9582 (pm3393) or 9600 (vsc7326)
enic: min_mtu 68, max_mtu 9000
gianfar: min_mtu 50, max_mu 9586
hns_enet: min_mtu 68, max_mtu 9578 (v1) or 9706 (v2)
ksz884x: min_mtu 60, max_mtu 1894
myri10ge: min_mtu 68, max_mtu 9000
natsemi: min_mtu 64, max_mtu 2024
nfp: min_mtu 68, max_mtu hardware-specific
forcedeth: min_mtu 64, max_mtu 1500 or 9100, depending on hardware
pch_gbe: min_mtu 46, max_mtu 10300
pasemi_mac: min_mtu 64, max_mtu 9000
qcaspi: min_mtu 46, max_mtu 1500
- remove qcaspi_netdev_change_mtu as it is now redundant
rocker: min_mtu 68, max_mtu 9000
sxgbe: min_mtu 68, max_mtu 9000
stmmac: min_mtu 46, max_mtu depends on hardware
tehuti: min_mtu 60, max_mtu 16384
- driver had no max mtu checking, but product docs say 16k jumbo packets
are supported by the hardware
netcp: min_mtu 68, max_mtu 9486
- remove netcp_ndo_change_mtu as it is now redundant
via-velocity: min_mtu 64, max_mtu 9000
octeon: min_mtu 46, max_mtu 65370
CC: netdev@vger.kernel.org
CC: Mark Einon <mark.einon@gmail.com>
CC: Vince Bridgers <vbridger@opensource.altera.com>
CC: Rasesh Mody <rasesh.mody@qlogic.com>
CC: Nicolas Ferre <nicolas.ferre@atmel.com>
CC: Santosh Raspatur <santosh@chelsio.com>
CC: Hariprasad S <hariprasad@chelsio.com>
CC: Christian Benvenuti <benve@cisco.com>
CC: Sujith Sankar <ssujith@cisco.com>
CC: Govindarajulu Varadarajan <_govind@gmx.com>
CC: Neel Patel <neepatel@cisco.com>
CC: Claudiu Manoil <claudiu.manoil@freescale.com>
CC: Yisen Zhuang <yisen.zhuang@huawei.com>
CC: Salil Mehta <salil.mehta@huawei.com>
CC: Hyong-Youb Kim <hykim@myri.com>
CC: Jakub Kicinski <jakub.kicinski@netronome.com>
CC: Olof Johansson <olof@lixom.net>
CC: Jiri Pirko <jiri@resnulli.us>
CC: Byungho An <bh74.an@samsung.com>
CC: Girish K S <ks.giri@samsung.com>
CC: Vipul Pandya <vipul.pandya@samsung.com>
CC: Giuseppe Cavallaro <peppe.cavallaro@st.com>
CC: Alexandre Torgue <alexandre.torgue@st.com>
CC: Andy Gospodarek <andy@greyhouse.net>
CC: Wingman Kwok <w-kwok2@ti.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Francois Romieu <romieu@fr.zoreil.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
i is defined as unsigned.
So print it with %u.
Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move the enic driver to new api {get|set}_link_ksettings.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Driver sets vlan_feature to netdev->features as hardware supports all of
them on vlan interface.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Don't hide varibles used by the logging macros.
Miscellanea:
o Use the more common ##__VA_ARGS__ extension
o Add missing newlines to formats
o Realign arguments
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Firmware posts the devcmd result in result ring. In case of timeout, driver
does not increment the current result pointer and firmware could post the
result after timeout has occurred. During next devcmd, driver would be
reading the result of previous devcmd.
Fix this by incrementing result even in case of timeout.
Fixes: 373fb0873d43 ("enic: add devcmd2")
Signed-off-by: Sandeep Pillai <sanpilla@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
NAPI drivers no longer need to observe a particular protocol
to benefit from busy polling (CONFIG_NET_RX_BUSY_POLL=y)
napi_hash_add() and napi_hash_del() are automatically called
from core networking stack, respectively from
netif_napi_add() and netif_napi_del()
This patch depends on free_netdev() and netif_napi_del() being
called from process context, which seems to be the norm.
Drivers might still prefer to call napi_hash_del() on their
own, since they might combine all the rcu grace periods into
a single one, knowing their NAPI structures lifetime, while
core networking stack has no idea of a possible combining.
Once this patch proves to not bring serious regressions,
we will cleanup drivers to either remove napi_hash_del()
or provide appropriate rcu grace periods combining.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The affinity hint is used by the user space daemon, irqbalancer, to
indicate a preferred CPU mask for irqs. This patch sets the irq affinity
hint to local numa core first, when exausted we try non-local numa cores.
Also set tx xps cpus mask bassed on affinity hint.
v2: remove the global affinity policy.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The current code invokes hang reset in case of error interrupt. We should
hang reset only in case of tx timeout. This because of the way hang reset
is implemented in firmware. Hang reset takes more firmware resources than
soft reset. Adaptor does not generate error interrupt in case of tx
timeout.
Hang reset only in case of tx timeout, in .ndo_tx_timeout. Do soft reset
otherwise. Introduce deferred work, enic_tx_hang_reset, to do hang reset.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the enic adaptors are know to generate spurious interrupts. When
error interrupt is generated, driver just resets the device. This patch
resets the device only when an error is occurred.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The flags argument will allow control of the dissection process (for
instance whether to parse beyond L3).
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
posted_index is RO in firmware. We need not do ioread everytime to get
posted index. Store posted index locally.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
err_out_vnic_unregister is used regardless of whether
SRIOV is enabled or not.
Reported-by: Jesse Brandeburg <jesse.brangeburg@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/built-in.o: In function `.vnic_wq_devcmd2_alloc':
(.text+0x49fe40): multiple definition of `.vnic_wq_devcmd2_alloc'
drivers/scsi/built-in.o:(.text+0xb4318): first defined here
drivers/net/built-in.o:(.opd+0x2af00): multiple definition of `vnic_wq_devcmd2_alloc'
drivers/scsi/built-in.o:(.opd+0xad70): first defined here
drivers/net/built-in.o: In function `.vnic_wq_init_start':
(.text+0x49f9c0): multiple definition of `.vnic_wq_init_start'
drivers/scsi/built-in.o:(.text+0xb3b58): first defined here
drivers/net/built-in.o:(.opd+0x2ae88): multiple definition of `vnic_wq_init_start'
drivers/scsi/built-in.o:(.opd+0xace0): first defined here
Rename these to 'enic_*' to avoid the conflict with the functiosn of
the same name in the snic scsi driver.
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
>> drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: sparse: incorrect type in assignment (different address spaces)
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: expected void *res
drivers/net/ethernet/cisco/enic/vnic_dev.c:1095:13: got void [noderef] <asn:2>*
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
devcmd is an interface for driver to communicate with fw/adaptor. It
involves writing data to hardware registers and waiting for the result.
This mechanism does not scale well. The queuing of "no wait" devcmds is
done in firmware memory rather than on the host. Firmware memory is a
rather more scarce and valuable resource than host memory. A devcmd storm
from one vf can disrupt the service on other pf/vf. The lack of flow
control allows for possible denial of server from one VM to another.
Devcmd2 uses work queue to post the devcmds, just like tx work queue. This
allows better flow control.
Initialize devcmd2, if fails we fall back to devcmd1.
Also change the driver version.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add devcmd resources to vnic_res_type. Add data types used by devcmd.
Signed-off-by: N V V Satyanarayana Reddy <nalreddy@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
pr_info does not give any details about the interface involved. This patch
uses netdev_info for printing the message. Use dev_info where netdev is not
ready.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some of the structure definitions are in .c file to make them private to
that file. This patch moves the struct definition to .h file, So that their
definitions are accessible from other files.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
* Allow setting of adaptive coalescing setting for all types of interrupt.
* In msi & legacy intr, we use single interrupt for rx & tx. In this case
tx_coalesce_usecs is invalid. We should use only rx_coalesce_usecs.
Do not display tx_coal values for msi/intx. And do not allow user to set
this as well.
* Driver supports only tx/rx_coalesce_usec and adaptive coalesce settings.
For other values, driver does not return error. So ethtool succeeds for
unsupported values. Introduce enic_coalesce_valid() function to validate
the coalescing values.
* If user requests for coalesce value greater than what adaptor supports,
driver uses the max value. We should at least log this.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Adaptive interrupt coalescing is available for msix. This patch adds the support
for msi poll. Interface for adaptive interrupt coalescing is already added in
driver. We just did not enable it for legacy intr & msi.
enic_calc_int_moderation() & enic_set_int_moderation() are defined as static
after enic_poll. Since enic_poll needs it, move both of these function
definitions above enic_poll. No change in functionality.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In enic_poll, we clean tx and rx queues, when low latency busy socket polling
is happening, enic_poll will only clean tx queue. After cleaning tx, it should
return total budget for re-poll.
There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi().
In this window if an irq occurs and napi is scheduled on different cpu, it tries
to acquire enic_poll_lock_napi() and fails. Unlock napi_poll before unmasking
the interrupt.
v2:
Do not change tx wonk done behaviour. Consider only rx work done for completing
napi.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We use spinlock to access a single flag. We can avoid spin_locks by using
atomic variable and atomic_cmpxchg(). Use atomic_cmpxchg to set the flag
for idle to poll. And a simple atomic_set to unlock (set idle from poll).
In napi poll, if gro is enabled, we call napi_gro_receive() to deliver the
packets. Before we call napi_complete(), i.e while re-polling, if low
latency busy poll is called, we use netif_receive_skb() to deliver the packets.
At this point if there are some skb's held in GRO, busy poll could deliver the
packets out of order. So we call napi_gro_flush() to flush skbs before we
move the napi poll to idle.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This howto made sense in the 1990s when users had to manually configure
ISA cards with jumpers or vendor utilities, but with the implementation
of PCI it became increasingly less and less relevant, to the point where
it has been well over a decade since I last updated it. And there is
no value in anyone else taking over updating it either.
However the references to it continue to spread as boiler plate text
from one Kconfig file into the next. We are not doing end users any
favours by pointing them at this old document, so lets kill it with
fire, once and for all, to hopefully stop any further spread.
No code is changed in this commit, just Kconfig help text.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
When incoming packet qualifies for rx_copybreak, we copy the data to newly
allocated skb. We do not free/unmap the original buffer. At this point driver
assumes this buffer is unallocated. When enic_rq_alloc_buf() is called for
buffer allocation, it checks if buf->os_buf is NULL. If its not NULL that means
buffer can be re-used.
When vnic_rq_clean() is called for freeing all rq buffers, and if the
rx_copybreak reused buffer falls outside the used desc, we do not free the
buffer. The following trace is observer when dma-debug is enabled.
Fix is to walk through complete ring and clean if buffer is present.
[ 40.555386] ------------[ cut here ]------------
[ 40.555396] WARNING: CPU: 0 PID: 491 at lib/dma-debug.c:971 dma_debug_device_change+0x188/0x1f0()
[ 40.555400] pci 0000:06:00.0: DMA-API: device driver has pending DMA allocations while released from device [count=4]
One of leaked entries details: [device address=0x00000000ff4cc040] [size=9018 bytes] [mapped with DMA_FROM_DEVICE] [mapped as single]
[ 40.555402] Modules linked in: nfsv3 nfs_acl rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 dns_resolver coretemp intel_rapl iosf_mbi x86_pkg_temp_thermal intel_powerclamp kvm_intel kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel aes_x86_64 lrw joydev mousedev gf128mul hid_generic glue_helper mgag200 usbhid ttm hid drm_kms_helper drm ablk_helper syscopyarea sysfillrect sysimgblt i2c_algo_bit i2c_core iTCO_wdt cryptd mac_hid evdev pcspkr sb_edac edac_core tpm_tis iTCO_vendor_support ipmi_si wmi tpm ipmi_msghandler shpchp lpc_ich processor acpi_power_meter hwmon button ac sch_fq_codel nfs lockd grace sunrpc fscache sd_mod ehci_pci ehci_hcd megaraid_sas usbcore scsi_mod usb_common enic(-) crc32c_generic crc32c_intel btrfs xor raid6_pq ext4 crc16 mbcache jbd2
[ 40.555467] CPU: 0 PID: 491 Comm: rmmod Not tainted 4.1.0-rc7-ARCH-01305-gf59b71f #118
[ 40.555469] Hardware name: Cisco Systems Inc UCSB-B200-M4/UCSB-B200-M4, BIOS B200M4.2.2.2.23.061220140128 06/12/2014
[ 40.555471] 0000000000000000 00000000e2f8a5b7 ffff880275f8bc48 ffffffff8158d6f0
[ 40.555474] 0000000000000000 ffff880275f8bca0 ffff880275f8bc88 ffffffff8107b04a
[ 40.555477] ffff8802734e0000 0000000000000004 ffff8804763fb3c0 ffff88027600b650
[ 40.555480] Call Trace:
[ 40.555488] [<ffffffff8158d6f0>] dump_stack+0x4f/0x7b
[ 40.555492] [<ffffffff8107b04a>] warn_slowpath_common+0x8a/0xc0
[ 40.555494] [<ffffffff8107b0d5>] warn_slowpath_fmt+0x55/0x70
[ 40.555498] [<ffffffff812fa408>] dma_debug_device_change+0x188/0x1f0
[ 40.555503] [<ffffffff8109aaef>] notifier_call_chain+0x4f/0x80
[ 40.555506] [<ffffffff8109aecb>] __blocking_notifier_call_chain+0x4b/0x70
[ 40.555510] [<ffffffff8109af06>] blocking_notifier_call_chain+0x16/0x20
[ 40.555514] [<ffffffff813f8066>] __device_release_driver+0xf6/0x120
[ 40.555518] [<ffffffff813f8b08>] driver_detach+0xc8/0xd0
[ 40.555523] [<ffffffff813f7c59>] bus_remove_driver+0x59/0xe0
[ 40.555527] [<ffffffff813f93a0>] driver_unregister+0x30/0x70
[ 40.555534] [<ffffffff8131532d>] pci_unregister_driver+0x2d/0xa0
[ 40.555542] [<ffffffffa0200ec2>] enic_cleanup_module+0x10/0x14e [enic]
[ 40.555547] [<ffffffff8110158f>] SyS_delete_module+0x1cf/0x280
[ 40.555551] [<ffffffff811e284e>] ? ____fput+0xe/0x10
[ 40.555554] [<ffffffff810980ec>] ? task_work_run+0xbc/0xf0
[ 40.555558] [<ffffffff815930ee>] system_call_fastpath+0x12/0x71
[ 40.555561] ---[ end trace 4988cadc77c2b236 ]---
[ 40.555562] Mapped at:
[ 40.555563] [<ffffffff812fa865>] debug_dma_map_page+0x95/0x150
[ 40.555566] [<ffffffffa01f4a88>] enic_rq_alloc_buf+0x1b8/0x360 [enic]
[ 40.555570] [<ffffffffa01f7658>] enic_open+0xf8/0x820 [enic]
[ 40.555574] [<ffffffff8148d50e>] __dev_open+0xce/0x150
[ 40.555579] [<ffffffff8148d851>] __dev_change_flags+0xa1/0x170
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We do not check the return value of enic_dev_stats_dump(). If allocation
fails, we will hit NULL pointer reference.
Return only if memory allocation fails. For other failures, we return the
previously recorded values.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is a small window between vnic_intr_unmask() and enic_poll_unlock_napi().
In this window if an irq occurs and napi is scheduled on different cpu, it tries
to acquire enic_poll_lock_napi() and hits the following WARN_ON message.
Fix is to unlock napi_poll before unmasking the interrupt.
[ 781.121746] ------------[ cut here ]------------
[ 781.121789] WARNING: CPU: 1 PID: 0 at drivers/net/ethernet/cisco/enic/vnic_rq.h:228 enic_poll_msix_rq+0x36a/0x3c0 [enic]()
[ 781.121834] Modules linked in: nfsv3 nfs_acl rpcsec_gss_krb5 auth_rpcgss oid_registry nfsv4 dns_resolver coretemp intel_rapl iosf_mbi x86_pkg_temp_thermal intel_powerclamp kvm_intel kvm crct10dif_pclmul crc32_pclmul ghash_clmulni_intel aesni_intel mgag200 ttm drm_kms_helper joydev aes_x86_64 lrw drm gf128mul mousedev glue_helper sb_edac ablk_helper iTCO_wdt iTCO_vendor_support evdev ipmi_si syscopyarea sysfillrect sysimgblt i2c_algo_bit i2c_core edac_core lpc_ich mac_hid cryptd pcspkr ipmi_msghandler shpchp tpm_tis acpi_power_meter tpm wmi processor hwmon button ac sch_fq_codel nfs lockd grace sunrpc fscache hid_generic usbhid hid ehci_pci ehci_hcd sd_mod megaraid_sas usbcore scsi_mod usb_common enic crc32c_generic crc32c_intel btrfs xor raid6_pq ext4 crc16 mbcache jbd2
[ 781.122176] CPU: 1 PID: 0 Comm: swapper/1 Not tainted 4.1.0-rc6-ARCH-00040-gc46a024-dirty #106
[ 781.122210] Hardware name: Cisco Systems Inc UCSB-B200-M4/UCSB-B200-M4, BIOS B200M4.2.2.2.23.061220140128 06/12/2014
[ 781.122252] 0000000000000000 bddbbc9d655ec96e ffff880277e43da8 ffffffff81583fe8
[ 781.122286] 0000000000000000 0000000000000000 ffff880277e43de8 ffffffff8107acfa
[ 781.122319] ffff880272c01000 ffff880273f18000 ffff880273f1a100 0000000000000000
[ 781.122352] Call Trace:
[ 781.122364] <IRQ> [<ffffffff81583fe8>] dump_stack+0x4f/0x7b
[ 781.122399] [<ffffffff8107acfa>] warn_slowpath_common+0x8a/0xc0
[ 781.122425] [<ffffffff8107ae2a>] warn_slowpath_null+0x1a/0x20
[ 781.122455] [<ffffffffa01fa9ca>] enic_poll_msix_rq+0x36a/0x3c0 [enic]
[ 781.122487] [<ffffffff8148525a>] net_rx_action+0x22a/0x370
[ 781.122512] [<ffffffff8107ed3d>] __do_softirq+0xed/0x2d0
[ 781.122537] [<ffffffff8107f06e>] irq_exit+0x7e/0xa0
[ 781.122560] [<ffffffff8158c424>] do_IRQ+0x64/0x100
[ 781.122582] [<ffffffff8158a42e>] common_interrupt+0x6e/0x6e
[ 781.122605] <EOI> [<ffffffff810bd331>] ? cpu_startup_entry+0x121/0x480
[ 781.122638] [<ffffffff810bd2fc>] ? cpu_startup_entry+0xec/0x480
[ 781.122667] [<ffffffff810f2ed3>] ? clockevents_register_device+0x113/0x1f0
[ 781.122698] [<ffffffff81050ab6>] start_secondary+0x196/0x1e0
[ 781.122723] ---[ end trace cec2e9dd3af7b9db ]---
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch adds full IPv6 addresses into flow_keys and uses them as
input to the flow hash function. The implementation supports either
IPv4 or IPv6 addresses in a union, and selector is used to determine
how may words to input to jhash2.
We also add flow_get_u32_dst and flow_get_u32_src functions which are
used to get a u32 representation of the source and destination
addresses. For IPv6, ipv6_addr_hash is called. These functions retain
getting the legacy values of src and dst in flow_keys.
With this patch, Ethertype and IP protocol are now included in the
flow hash input.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
add couple of empty lines on the way.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/rocker/rocker.c
The rocker commit was two overlapping changes, one to rename
the ->vport member to ->pport, and another making the bitmask
expression use '1ULL' instead of plain '1'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the built-in function instead of memset.
Signed-off-by: Joe Perches <joe@perches.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We should complete notify_check before returning the credits. Once we return the
credits, adaptor may access the notify data.
Signed-off-by: Sujith Sankar <ssujith@cisco.com>
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this patch fixes following sparse warnings:
enic_main.c:92:28: warning: symbol 'mod_table' was not declared. Should it be static?
enic_main.c:109:28: warning: symbol 'mod_range' was not declared. Should it be static?
enic_main.c:1306:5: warning: symbol 'enic_busy_poll' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
this patch fixes following sparse warning:
enic_ethtool.c:95:6: warning: symbol 'enic_intr_coal_set_rx' was not declared. Should it be static?
Signed-off-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
arch/arm/boot/dts/imx6sx-sdb.dts
net/sched/cls_bpf.c
Two simple sets of overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
With the commit d75b1ade567ffab ("net: less interrupt masking in NAPI") napi repoll
is done only when work_done == budget. When we are in busy_poll we return 0 in
napi_poll. We should return budget.
Signed-off-by: Govindarajulu Varadarajan <_govind@gmx.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The same macros are used for rx as well. So rename it.
Signed-off-by: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: David S. Miller <davem@davemloft.net>
|