| Age | Commit message (Collapse) | Author |
|---|
|
BCM4908 devices have MAC address accessible using NVMEM so it's needed
to use OF helper for reading it.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When receiving a lot of packets hardware may run out of free
descriptiors and stop RX ring. Enable it every time after handling
received packets.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210226132038.29849-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The following trace excerpt corresponds with a NULL pointer dereference
of 'bp->irq_tbl' in bnxt_setup_inta() on an Aarch64 system after many
device resets:
Unable to handle kernel NULL pointer dereference at ... 000000d
...
pc : string+0x3c/0x80
lr : vsnprintf+0x294/0x7e0
sp : ffff00000f61ba70 pstate : 20000145
x29: ffff00000f61ba70 x28: 000000000000000d
x27: ffff0000009c8b5a x26: ffff00000f61bb80
x25: ffff0000009c8b5a x24: 0000000000000012
x23: 00000000ffffffe0 x22: ffff000008990428
x21: ffff00000f61bb80 x20: 000000000000000d
x19: 000000000000001f x18: 0000000000000000
x17: 0000000000000000 x16: ffff800b6d0fb400
x15: 0000000000000000 x14: ffff800b7fe31ae8
x13: 00001ed16472c920 x12: ffff000008c6b1c9
x11: ffff000008cf0580 x10: ffff00000f61bb80
x9 : 00000000ffffffd8 x8 : 000000000000000c
x7 : ffff800b684b8000 x6 : 0000000000000000
x5 : 0000000000000065 x4 : 0000000000000001
x3 : ffff0a00ffffff04 x2 : 000000000000001f
x1 : 0000000000000000 x0 : 000000000000000d
Call trace:
string+0x3c/0x80
vsnprintf+0x294/0x7e0
snprintf+0x44/0x50
__bnxt_open_nic+0x34c/0x928 [bnxt_en]
bnxt_open+0xe8/0x238 [bnxt_en]
__dev_open+0xbc/0x130
__dev_change_flags+0x12c/0x168
dev_change_flags+0x20/0x60
...
Ordinarily, a call to bnxt_setup_inta() (not in trace due to inlining)
would not be expected on a system supporting MSIX at all. However, if
bnxt_init_int_mode() does not end up being called after the call to
bnxt_clear_int_mode() in bnxt_fw_reset_close(), then the driver will
think that only INTA is supported and bp->irq_tbl will be NULL,
causing the above crash.
In the error recovery scenario, we call bnxt_clear_int_mode() in
bnxt_fw_reset_close() early in the sequence. Ordinarily, we will
call bnxt_init_int_mode() in bnxt_hwrm_if_change() after we
reestablish communication with the firmware after reset. However,
if the sequence has to abort before we call bnxt_init_int_mode() and
if the user later attempts to re-open the device, then it will cause
the crash above.
We fix it in 2 ways:
1. Check for bp->irq_tbl in bnxt_setup_int_mode(). If it is NULL, call
bnxt_init_init_mode().
2. If we need to abort in bnxt_hwrm_if_change() and cannot complete
the error recovery sequence, set the BNXT_STATE_ABORT_ERR flag. This
will cause more drastic recovery at the next attempt to re-open the
device, including a call to bnxt_init_int_mode().
Fixes: 3bc7d4a352ef ("bnxt_en: Add BNXT_STATE_IN_FW_RESET state.")
Reviewed-by: Scott Branden <scott.branden@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The driver's error recovery reset sequence can take many seconds to
complete and only the critical sections are protected by rtnl_lock.
A recent change has introduced a regression in this sequence.
bnxt_remove_one() may be called while the recovery is in progress.
Normally, unregister_netdev() would cause bnxt_close_nic() to be
called and this would cause the error recovery to safely abort
with the BNXT_STATE_ABORT_ERR flag set in bnxt_close_nic().
Recently, we added bnxt_reinit_after_abort() to allow the user to
reopen the device after an aborted recovery. This causes the
regression in the scenario described above because we would
attempt to re-open even after the netdev has been unregistered.
Fix it by checking the netdev reg_state in
bnxt_reinit_after_abort() and abort if it is unregistered.
Fixes: 6882c36cf82e ("bnxt_en: attempt to reinitialize after aborted reset")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Missing increment was resulting in poll function always returning 0
instead of amount of processed packets.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210224151842.2419-2-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
After filling RX ring slot with new skb it's required to free old skb.
Immediately on error or later in the net subsystem.
Fixes: 4feffeadbcb2 ("net: broadcom: bcm4908enet: add BCM4908 controller driver")
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210224151842.2419-1-zajec5@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In ndo_stop functions, netdev_completed_queue() is called during forced
tx reclaim, after netdev_reset_queue(). This may trigger kernel panic if
there is any tx skb left.
This patch moves netdev_reset_queue() to after tx reclaim, so BQL can
complete successfully then reset.
Signed-off-by: Sieng Piaw Liew <liew.s.piaw@gmail.com>
Fixes: 4c59b0f5543d ("bcm63xx_enet: add BQL support")
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210222013530.1356-1-liew.s.piaw@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
|
|
The tg3 driver tried to communicate towards the PHY driver whether it
wanted RGMII in-band signaling enabled or disabled however there is
nothing that looks at those flags in drivers/net/phy/broadcom.c so this
does do not anything.
Suggested-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some internal PHY's have their events like link change reported by the
MAC interrupt. We have PHY_IGNORE_INTERRUPT to deal with this scenario.
I'm not too happy with this name. We don't ignore interrupts, typically
there is no interrupt exposed at a PHY level. So let's rename it to
PHY_MAC_INTERRUPT. This is in line with phy_mac_interrupt(), which is
called from the MAC interrupt handler to handle PHY events.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Hardware comes up with default max frame size set to 1518. When using it
with switch it results in actual Ethernet MTU 1492:
1518 - 14 (Ethernet header) - 4 (Broadcom's tag) - 4 (802.1q) - 4 (FCS)
Above means hardware in its default state can't handle standard Ethernet
traffic (MTU 1500).
Define maximum possible Ethernet overhead and always set MAC max frame
length accordingly. This change fixes handling Ethernet frames of length
1506 - 1514.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We currently only log the error recovery settings if it is enabled.
In some cases, firmware disables error recovery after it was
initially enabled. Without logging anything, the user will not be
aware of this change in setting.
Log it when error recovery is disabled. Also, change the reset count
value from hexadecimal to decimal.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This is a new async message that the firmware can send to check if it
can communicate with the driver. This is an added error detection
scheme that firmware can use if it suspects errors in the PCIe
interface. When the driver receives this async message, it will reply
back echoing some data in the async message. If the firmware is not
getting the reply with the proper data after some retries, error
recovery will kick in.
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If firmware provides the offset to the "context kind" field of the
relevant context memory blocks, we'll initialize just that field for
each block instead of initializing all of context memory.
Populate the bnxt_mem_init structure with the proper offset returned
by firmware. If it is older firmware and the information is not
available, we set the offset to an invalid value and fall back to
the old behavior of initializing every byte. Otherwise, we initialize
only the "context kind" byte at the offset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, the driver calls memset() to set all relevant context memory
used by the chip to the initial value. This can take many milliseconds
with the potentially large number of context pages allocated for the
chip.
To make this faster, we only need to initialize the "context kind" field
of each block of context memory. This patch sets up the infrastructure
to do that with the bnxt_mem_init structure. In the next patch, we'll
add the logic to obtain the offset of the "context kind" from the
firmware. This patch is not changing the current behavior of calling
memset() to initialize all relevant context memory.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
During some fatal firmware error conditions, the PCI config space
register 0x2e which normally contains the subsystem ID will become
0xffff. This register will revert back to the normal value after
the chip has completed core reset. If we detect this condition,
we can poll this config register immediately for the value to revert.
Because we use config read cycles to poll this register, there is no
possibility of Master Abort if we happen to read it during core reset.
This speeds up recovery significantly as we don't have to wait for the
conservative min_time before polling MMIO to see if the firmware has
come out of reset. As soon as this register changes value we can
proceed to re-initialize the device.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Newer devices may have local context memory instead of relying on the
host for backing store. In these cases, HWRM_FUNC_BACKING_STORE_QCAPS
will return a zero entry size to indicate contexts for which the host
should not allocate backing store.
Selectively allocate context memory based on device capabilities and
only enable backing store for the appropriate contexts.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The main changes are the echo request/response from firmware for error
detection and the NO_FCS feature to transmit frames without FCS.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use le32_to_cpu() for reading __le32 struct field filled by hw.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use ETH_FCS_LEN instead of magic value and drop incorrect + 2
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
1. Fix "ensable" typo noticed by Andrew
2. Fix chipset name in the struct net_device_ops variable
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It seems preferred to let compiler optimize code if applicable.
While at it drop unused enet_umac_maskset().
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
dma_alloc_coherent takes care of zeroing allocated memory
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
compatible string was updated to match normal naming convention so
update driver as well
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The running fw.psid version is in decimal format but the stored
fw.psid is in hex format. This can mislead the user to reset the
NIC to activate the stored version to become the running version.
Fix it to display the stored fw.psid in decimal format.
Fixes: 1388875b3916 ("bnxt_en: Add stored FW version info to devlink info_get cb.")
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A TX queue can potentially immediately timeout after it is stopped
and the last TX timestamp on that queue was more than 5 seconds ago with
carrier still up. Prevent these intermittent false TX timeouts
by bringing down carrier first before calling netif_tx_disable().
Fixes: c0c050c58d84 ("bnxt_en: New Broadcom ethernet driver.")
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
BCM4908 SoCs family uses Ethernel controller that includes UniMAC but
uses different DMA engine (than other controllers) and requires
different programming.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use the various netif_level() helpers to simplify the C code. This was
suggested by Joe Perches.
Cc: Joe Perches <joe@perches.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/1611642024-3166-1-git-send-email-michael.chan@broadcom.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Once the firmware fatal condition is detected, we should cease
comminication with the firmware and hardware quickly even if there
are many completion entries in the completion rings. This will
speed up the recovery process and prevent further I/Os that may
cause further exceptions.
Do not proceed in the NAPI poll function if fatal condition is
detected. Call napi_complete() and return without arming interrupts.
Cleanup of all rings and reset are imminent.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Combine the three netdev_warn() calls into a single call, printed at
the NETIF_MSG_HW log level.
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the event of a fatal firmware error, firmware will notify the host
and then it will proceed to do core reset when it sees that all functions
have disabled Bus Master. To prevent Master Aborts and other hard
errors, we need to quiesce all activities in addition to disabling Bus
Master before the chip goes into core reset.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
In the event of a fatal firmware error, we want to disable IRQ early
in the recovery sequence. This change will allow it to be called
safely again as part of the normal shutdown sequence.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Up until now, we don't need to keep track of this state because NAPI
is always enabled once and disabled once during bring up and shutdown.
For better error recovery in subsequent patches, we want to quiesce
the device earlier during fatal error conditions. The normal shutdown
sequence will disable NAPI again and the flag will prevent disabling
NAPI twice.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Reviewed-by: Andy Gospodarek <gospo@broadcom.com>
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Reviewed-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
This code to check if we have reached the maximum wait time after
firmware reset is used multiple times. Add a helper function to
do this.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware may be in the middle of reset when the driver tries to do ifup.
In that case, firmware will return a special error code and the driver
will retry 10 times with 50 msecs delay after each retry.
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Drawing a hard line on aborted resets prevents a NIC open in
some scenarios that may otherwise be recoverable. For example,
if a firmware recovery happened while a PF was down and an
attempt was made to bring up an associated VF in this state,
then it was impossible to ever bring up this VF without a
rebind or reload of its driver.
Attempt to reinitialize the firmware when an aborted reset (or
failed init after a reset) is discovered during open - it may
succeed. Also take care to allow the user to retry opening the
NIC even after an aborted reset.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Firmware is capable of generating asynchronous debug notifications.
The event data is opaque to the driver and is simply logged. Debug
notifications can be enabled by turning on hardware status messages
using the ethtool msglvl interface.
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The timeout period for firmware messages is passed to the driver
from the firmware in the response of the first command. This
timeout period is multiplied by a factor for certain long
running commands such as NVRAM commands. In some cases, the
timeout period can become really long and it can cause hung task
warnings if firmware has crashed or is not responding. To avoid
such long delays, cap all firmware commands to a max timeout value
of 40 seconds.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
If firmware is in reset or in bad state, it won't be able to return
VPD data. Move bnxt_vpd_read_info() until after bnxt_fw_init_one_p1()
successfully returns. By then we would have established proper
communications with the firmware.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Vasundhara Volam <vasundhara-v.volam@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The first HWRM_VER_GET message to firmware during probe may timeout if
firmware is under reset. This can happen during hot-plug for example.
On P5 and newer chips, we can check if firmware is in the boot stage by
reading a status register. Retry 5 times if the status register shows
that firmware is not ready and not in error state.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Add missing support for handling NO_MASTER crashes while ports are
administratively down (ifdown). On some SoC platforms, the driver
needs to assist the firmware to recover from a crash via OP-TEE.
This is performed in a similar fashion to what is done during driver
probe.
Signed-off-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Define macros to check for the various states in the lower 16 bits of
the health register. Replace the C code that checks for these values
with the newly defined macros.
Reviewed-by: Edwin Peer <edwin.peer@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Updates to backing store APIs, QoS profiles, and push buffer initial
index support.
Since the new HWRM_FUNC_BACKING_STORE_CFG message size has increased,
we need to add some compat. logic to fall back to the smaller legacy
size if firmware cannot accept the larger message size. The new fields
added to the structure are not used yet.
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Acked-by: Willem de Bruijn <willemb@google.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When working on the PCI VPD code I also tested with a Broadcom BCM95719
card. tg3 uses internal NVRAM access with this card, so I forced it to
PCI VPD mode for testing. PCI VPD access fails
(i + PCI_VPD_LRDT_TAG_SIZE + j > len) because only TG3_NVM_VPD_LEN (256)
bytes are read, but PCI VPD has 400 bytes on this card.
So add a constant TG3_NVM_PCI_VPD_MAX_LEN that defines the maximum
PCI VPD size. The actual VPD size is returned by pci_read_vpd().
In addition it's not worth looping over pci_read_vpd(). If we miss the
125ms timeout per VPD dword read then definitely something is wrong,
and if the tg3 module loading is killed then there's also not much
benefit in retrying the VPD read.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Michael Chan <michael.chan@broadcom.com>
Link: https://lore.kernel.org/r/cb9e9113-0861-3904-87e0-d4c4ab3c8860@gmail.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Conflicts:
drivers/net/can/dev.c
commit 03f16c5075b2 ("can: dev: can_restart: fix use after free bug")
commit 3e77f70e7345 ("can: dev: move driver related infrastructure into separate subdir")
Code move.
drivers/net/dsa/b53/b53_common.c
commit 8e4052c32d6b ("net: dsa: b53: fix an off by one in checking "vlan->vid"")
commit b7a9e0da2d1c ("net: switchdev: remove vid_begin -> vid_end range from VLAN objects")
Field rename.
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
On the error path, it should goto the error handling label to free
allocated memory rather than directly return.
Fixes: 31bc72d97656 ("net: systemport: fetch and use clock resources")
Signed-off-by: Pan Bian <bianpan2016@163.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Link: https://lore.kernel.org/r/20210120044423.1704-1-bianpan2016@163.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Daniel Borkmann says:
====================
pull-request: bpf-next 2021-01-16
1) Extend atomic operations to the BPF instruction set along with x86-64 JIT support,
that is, atomic{,64}_{xchg,cmpxchg,fetch_{add,and,or,xor}}, from Brendan Jackman.
2) Add support for using kernel module global variables (__ksym externs in BPF
programs) retrieved via module's BTF, from Andrii Nakryiko.
3) Generalize BPF stackmap's buildid retrieval and add support to have buildid
stored in mmap2 event for perf, from Jiri Olsa.
4) Various fixes for cross-building BPF sefltests out-of-tree which then will
unblock wider automated testing on ARM hardware, from Jean-Philippe Brucker.
5) Allow to retrieve SOL_SOCKET opts from sock_addr progs, from Daniel Borkmann.
6) Clean up driver's XDP buffer init and split into two helpers to init per-
descriptor and non-changing fields during processing, from Lorenzo Bianconi.
7) Minor misc improvements to libbpf & bpftool, from Ian Rogers.
* https://git.kernel.org/pub/scm/linux/kernel/git/bpf/bpf-next: (41 commits)
perf: Add build id data in mmap2 event
bpf: Add size arg to build_id_parse function
bpf: Move stack_map_get_build_id into lib
bpf: Document new atomic instructions
bpf: Add tests for new BPF atomic operations
bpf: Add bitwise atomic instructions
bpf: Pull out a macro for interpreting atomic ALU operations
bpf: Add instructions for atomic_[cmp]xchg
bpf: Add BPF_FETCH field / create atomic_fetch_add instruction
bpf: Move BPF_STX reserved field check into BPF_STX verifier code
bpf: Rename BPF_XADD and prepare to encode other atomics in .imm
bpf: x86: Factor out a lookup table for some ALU opcodes
bpf: x86: Factor out emission of REX byte
bpf: x86: Factor out emission of ModR/M for *(reg + off)
tools/bpftool: Add -Wall when building BPF programs
bpf, libbpf: Avoid unused function warning on bpf_tail_call_static
selftests/bpf: Install btf_dump test cases
selftests/bpf: Fix installation of urandom_read
selftests/bpf: Move generated test files to $(TEST_GEN_FILES)
selftests/bpf: Fix out-of-tree build
...
====================
Link: https://lore.kernel.org/r/20210116012922.17823-1-daniel@iogearbox.net
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
When the FW tells the driver to retry the INSTALL_UPDATE command after
it has cleared the NVM area, the driver is not clearing the previously
used ALLOWED_TO_DEFRAG flag. As a result the FW tries to defrag the NVM
area a second time in a loop and can fail the request.
Fixes: 1432c3f6a6ca ("bnxt_en: Retry installing FW package under NO_SPACE error condition.")
Signed-off-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
|
The function bnxt_get_ulp_stat_ctxs() does not count the stats contexts
used by the RDMA driver correctly when the RDMA driver is freeing the
MSIX vectors. It assumes that if the RDMA driver is registered, the
additional stats contexts will be needed. This is not true when the
RDMA driver is about to unregister and frees the MSIX vectors.
This slight error leads to over accouting of the stats contexts needed
after the RDMA driver has unloaded. This will cause some firmware
warning and error messages in dmesg during subsequent config. changes
or ifdown/ifup.
Fix it by properly accouting for extra stats contexts only if the
RDMA driver is registered and MSIX vectors have been successfully
requested.
Fixes: c027c6b4e91f ("bnxt_en: get rid of num_stat_ctxs variable")
Reviewed-by: Yongping Zhang <yongping.zhang@broadcom.com>
Reviewed-by: Pavan Chebbi <pavan.chebbi@broadcom.com>
Signed-off-by: Michael Chan <michael.chan@broadcom.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
|
