| Age | Commit message (Collapse) | Author |
|---|
|
Configuring VLANs from the VF side had no effect, because the PF ignored
filters of type VFPF_VLAN_FILTER in the VF-PF message.
Add the missing filter type to configure.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
filters->count is the number of filters we were supposed to configure.
There is no reason to increase it by +1 when printing the count in an error
message.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On failure to configure a VF MAC/VLAN filter we should not attempt to
rollback filters that we failed to configure with -EEXIST.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VFs are currently missing the VLAN filtering feature, because we were
checking the PF's acquire response before actually performing the acquire.
Fix it by setting the feature flag later when we have the PF response.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is too late to check for the limit of the number of VF multicast
addresses after they have already been copied to the req->multicast[]
array, possibly overflowing it.
Do the check before copying.
Also fix the error path to not skip unlocking vf2pf_mutex.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When BNX2X_MSG_IOV is enabled, the driver produces too many VF statistics
messages. Lower the verbosity of the VF stats messages similarly as in
commit 76ca70fabbdaa3 ("bnx2x: [Debug] change verbosity of some prints").
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to crash the kernel by accessing a PTP device while its
associated bnx2x interface is down. Before the interface is brought up,
the timecounter is not initialized, so accessing it results in NULL
dereference.
Fix it by checking if the interface is up.
Use -ENETDOWN as the error code when the interface is down.
-EFAULT in bnx2x_ptp_adjfreq() did not seem right.
Tested using phc_ctl get/set/adj/freq commands.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix typos and add the following to the scripts/spelling.txt:
initialiazation||initialization
While we are here, fix the "overriden" in the touched line in
drivers/net/ethernet/broadcom/bnx2x/bnx2x_link.c.
Link: http://lkml.kernel.org/r/1481573103-11329-17-git-send-email-yamada.masahiro@socionext.com
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
napi_complete_done() allows to opt-in for gro_flush_timeout,
added back in linux-3.19, commit 3b47d30396ba
("net: gro: add a per device gro flush timer")
This allows for more efficient GRO aggregation without
sacrifying latencies.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ethtool api {get|set}_settings is deprecated.
We move this driver to new api {get|set}_link_ksettings.
As I don't have the hardware, I'd be very pleased if
someone may test this patch.
Signed-off-by: Philippe Reynes <tremyfr@gmail.com>
Acked-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Commit 4cace675d687 ("bnx2x: Alloc 4k fragment for each rx ring buffer
element") added extra put_page() and get_page() calls on arches where
PAGE_SIZE=4K like x86
Reorder things to avoid this overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Gabriel Krisman Bertazi <krisman@linux.vnet.ibm.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There is no point in having an extra type for extra confusion. u64 is
unambiguous.
Conversion was done with the following coccinelle script:
@rem@
@@
-typedef u64 cycle_t;
@fix@
typedef cycle_t;
@@
-cycle_t
+u64
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: John Stultz <john.stultz@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
NTB: correct ntb_spad_count comment typo
misc: ibmasm: fix typo in error message
Remove references to dead make variable LINUX_INCLUDE
Remove last traces of ikconfig.h
treewide: Fix printk() message errors
Documentation/device-mapper: s/getsize/getsz/
|
|
This patch fix spelling typos in printk and kconfig.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
|
|
Only the 578xx adapters are capable of configuring UDP ports for
the purpose of tunnelling - doing the same on 577xx might lead to
a firmware assertion.
We're already not claiming support for any related feature for such
devices, but we also need to prevent the configuration of the UDP
ports to the device in this case.
Fixes: f34fa14cc033 ("bnx2x: Add vxlan RSS support")
Reported-by: Anikina Anna <anikina@gmail.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Until interface is up [and assuming ringparams weren't explicitly
configured] when queried for the size of its rings bnx2x would
claim they're the maximal size by default.
That is incorrect as by default the maximal number of buffers would
be equally divided between the various rx rings.
This prevents the user from actually setting the number of elements
on each rx ring to be of maximal size prior to transitioning the
interface into up state.
To fix this, make a rough estimation about the number of buffers.
It wouldn't always be accurate, but it would be much better than
current estimation and would allow users to increase number of
buffers during early initialization of the interface.
Reported-by: Seymour, Shane <shane.seymour@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Macro BNX2X_ALLOC_AND_SET(arr, lbl, func) calls kmalloc() to allocate
memory, and jumps to label "lbl" if the allocation fails. Label "lbl"
first cleans memory and then returns variable rc. Before calling the
macro, the value of variable rc is 0. Because 0 means no error, the
callers of bnx2x_init_firmware() may be misled. This patch fixes the bug,
assigning "-ENOMEM" to rc before calling macro NX2X_ALLOC_AND_SET().
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=189141
Signed-off-by: Pan Bian <bianpan2016@163.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since offset is zero, it's not necessary to use set function. Reset
function is straightforward, and will remove the unnecessary add
operation in set function.
Signed-off-by: Zhang Shengju <zhangshengju@cmss.chinamobile.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Switch from napi_complete() to napi_complete_done()
for better GRO support (gro_flush_timeout) and core NAPI
features.
Do not rearm interrupts if we are busy polling,
to reduce bus and interrupts overhead.
Signed-off-by: Eric Dumazet <edumazet@google.com>
Cc: Willem de Bruijn <willemb@google.com>
Cc: Adam Belay <abelay@google.com>
Cc: Tariq Toukan <tariqt@mellanox.com>
Cc: Yuval Mintz <Yuval.Mintz@cavium.com>
Cc: Ariel Elior <ariel.elior@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Mostly simple overlapping changes.
For example, David Ahern's adjacency list revamp in 'net-next'
conflicted with an adjacency list traversal bug fix in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Time Sync (PTP) implementation uses the divisor/shift value for converting
the clock ticks to nanoseconds. Driver currently defines shift value as 1,
this results in the nanoseconds value to be calculated as half the actual
value. Hence the user application fails to synchronize the device clock
value with the PTP master device clock. Need to use the 'shift' value of 0.
Signed-off-by: Sony.Chacko <Sony.Chacko@cavium.com>
Signed-off-by: Sudarsana Reddy Kalluru <Sudarsana.Kalluru@cavium.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@cavium.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
tg3: min_mtu 60, max_mtu 9000/1500
bnxt: min_mtu 60, max_mtu 9000
bnx2x: min_mtu 46, max_mtu 9600
- Fix up ETH_OVREHEAD -> ETH_OVERHEAD while we're in here, remove
duplicated defines from bnx2x_link.c.
bnx2: min_mtu 46, max_mtu 9000
- Use more standard ETH_* defines while we're at it.
bcm63xx_enet: min_mtu 46, max_mtu 2028
- compute_hw_mtu was made largely pointless, and thus merged back into
bcm_enet_change_mtu.
b44: min_mtu 60, max_mtu 1500
CC: netdev@vger.kernel.org
CC: Michael Chan <michael.chan@broadcom.com>
CC: Sony Chacko <sony.chacko@qlogic.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Dept-HSGLinuxNICDev@qlogic.com
CC: Siva Reddy Kallam <siva.kallam@broadcom.com>
CC: Prashant Sreedharan <prashant@broadcom.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The group list must be freed prior to freeing the command otherwise
we have a use-after-free.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for the pending list to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Acked-by: Yuval Mintz <Yuval.Mintz@caviumnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently, we can have high order page allocations that specify
GFP_ATOMIC when configuring multicast MAC address filters.
For example, we have seen order 2 page allocation failures with
~500 multicast addresses configured.
Convert the allocation for 'mcast_list' to be done in PAGE_SIZE
increments.
Signed-off-by: Jason Baron <jbaron@akamai.com>
Cc: Yuval Mintz <Yuval.Mintz@qlogic.com>
Cc: Ariel Elior <Ariel.Elior@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Introduce new rtnl UAPI that exposes a list of vlans per VF, giving
the ability for user-space application to specify it for the VF, as an
option to support 802.1ad.
We adjusted IP Link tool to support this option.
For future use cases, the new UAPI supports multiple vlans. For now we
limit the list size to a single vlan in kernel.
Add IFLA_VF_VLAN_LIST in addition to IFLA_VF_VLAN to keep backward
compatibility with older versions of IP Link tool.
Add a vlan protocol parameter to the ndo_set_vf_vlan callback.
We kept 802.1Q as the drivers' default vlan protocol.
Suitable ip link tool command examples:
Set vf vlan protocol 802.1ad:
ip link set eth0 vf 1 vlan 100 proto 802.1ad
Set vf to VST (802.1Q) mode:
ip link set eth0 vf 1 vlan 100 proto 802.1Q
Or by omitting the new parameter
ip link set eth0 vf 1 vlan 100
Signed-off-by: Moshe Shemesh <moshe@mellanox.com>
Signed-off-by: Tariq Toukan <tariqt@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/ethernet/mediatek/mtk_eth_soc.c
drivers/net/ethernet/qlogic/qed/qed_dcbx.c
drivers/net/phy/Kconfig
All conflicts were cases of overlapping commits.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Tested-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When PCI error is detected, in some architectures (like PowerPC) a slot
reset is performed - the driver's error handlers are in charge of "disable"
device before the reset, and re-enable it after a successful slot reset.
There are two cases though that another path is taken on the code: if the
slot reset is not successful or if too many errors already happened in the
specific adapter (meaning that possibly the device is experiencing a HW
failure that slot reset is not able to solve), the core PCI error mechanism
(called EEH in PowerPC) will remove the adapter from the system, since it
will consider this as a permanent failure on device. In this case, a path
is taken that leads to bnx2x_chip_cleanup() calling bnx2x_reset_hw(), which
then tries to perform a HW reset on chip. This reset won't succeed since
the HW is in a fault state, which can be seen by multiple messages on
kernel log like below:
bnx2x: [bnx2x_issue_dmae_with_comp:552(eth1)]DMAE timeout!
bnx2x: [bnx2x_write_dmae:600(eth1)]DMAE returned failure -1
After some time, the PCI error mechanism gives up on waiting the driver's
correct removal procedure and forcibly remove the adapter from the system.
We can see soft lockup while core PCI error mechanism is waiting for driver
to accomplish the right removal process.
This patch adds a verification to avoid a chip reset whenever the function
is in PCI error state - since this case is only reached when we have a
device being removed because of a permanent failure, the HW chip reset is
not expected to work fine neither is necessary.
Also, as a minor improvement in error path, we avoid the MCP information dump
in case of non-recoverable PCI error (when adapter is about to be removed),
since it will certainly fail.
Reported-by: Harsha Thyagaraja <hathyaga@in.ibm.com>
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When ndo_set_rx_mode() is called for bnx2x, as part of process of
configuring the new MAC address filters [both unicast & multicast]
driver begins by flushing the existing configuration and then iterating
over the network device's list of addresses and configures those instead.
This has the side-effect of creating a short gap where traffic wouldn't
be properly classified, as no filters are configured in HW.
While for unicasts this is rather insignificant [as unicast MACs don't
frequently change while interface is actually running],
for multicast traffic it does pose an issue as there are multicast-based
networks where new multicast groups would constantly be removed and
added.
This patch tries to remedy this [at least for the newer adapters] -
Instead of flushing & reconfiguring all existing multicast filters,
the driver would instead create the approximate hash match that would
result from the required filters. It would then compare it against the
currently configured approximate hash match, and only add and remove the
delta between those.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch goes through and combines the notifiers for VXLAN and GENEVE
into a single function for each action. So there is now one combined
function for getting ports, one for adding the ports, and one for deleting
the ports.
I also went through and dropped the BNX2X VXLAN and GENEVE specific build
flags.
Signed-off-by: Alexander Duyck <aduyck@mirantis.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since implementing VLAN filtering in commit 05cc5a39ddb74
("bnx2x: add vlan filtering offload") bnx2x refuses to add a VLAN while
the interface is down:
# ip link add link enp3s0f0 enp3s0f0_10 type vlan id 10
RTNETLINK answers: Bad address
and in dmesg (with bnx2x.debug=0x20):
bnx2x: [bnx2x_vlan_rx_add_vid:12941(enp3s0f0)]Ignoring VLAN
configuration the interface is down
Other drivers have no problem with this.
Fix this peculiar behavior in the following way:
- Accept requests to add/kill VID regardless of the device state.
Maintain the requested list of VIDs in the bp->vlan_reg list.
- If the device is up, try to configure the VID list into the hardware.
If we run out of VLAN credits or encounter a failure configuring an
entry, fall back to accepting all VLANs.
If we successfully configure all entries from the list, turn the
fallback off.
- Use the same code for reconfiguring VLANs during NIC load.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x_init_bp() allocates memory with bnx2x_alloc_mem_bp() so if we
fail later in bnx2x_init_one() we need to free this memory
with bnx2x_free_mem_bp() to avoid leakages. E.g. I'm observing memory
leaks reported by kmemleak when a failure (unrelated) happens in
bnx2x_vfpf_acquire().
Signed-off-by: Vitaly Kuznetsov <vkuznets@redhat.com>
Acked-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch defines two new GSO definitions SKB_GSO_IPXIP4 and
SKB_GSO_IPXIP6 along with corresponding NETIF_F_GSO_IPXIP4 and
NETIF_F_GSO_IPXIP6. These are used to described IP in IP
tunnel and what the outer protocol is. The inner protocol
can be deduced from other GSO types (e.g. SKB_GSO_TCPV4 and
SKB_GSO_TCPV6). The GSO types of SKB_GSO_IPIP and SKB_GSO_SIT
are removed (these are both instances of SKB_GSO_IPXIP4).
SKB_GSO_IPXIP6 will be used when support for GSO with IP
encapsulation over IPv6 is added.
Signed-off-by: Tom Herbert <tom@herbertland.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Not all adapters have FC-NPIV configured. If bnx2fc is used with such an
adapter, driver would read irrelevant data from the the nvram and log
"FC-NPIV table with bad length..." In system logs.
Simply accept that reading '0' as the feature offset in nvram indicates
the feature isn't there and return.
Reported-by: Andrew Patterson <andrew.patterson@hpe.com>
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When driver has hit a parity event, HW can no longer write to host memory.
As a result, Tx completions cannot be written to the host SB memory, and
waiting for Tx completions eventually timeout.
As driver is willing to delay as much as 1-2 seconds per Tx queue for its
draining and this delay is sequential, the time to recover might greatly
lengthen needlessly in case the recovery is done under multi-connection
traffic.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Several cases of overlapping changes, as well as one instance
(vxlan) of a bug fix in 'net' overlapping with code movement
in 'net-next'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
I added this check in setup_tc to multiple drivers,
if (handle != TC_H_ROOT || tc->type != TC_SETUP_MQPRIO)
Unfortunately restricting to TC_H_ROOT like this breaks the old
instantiation of mqprio to setup a hardware qdisc. This patch
relaxes the test to only check the type to make it equivalent
to the check before I broke it. With this the old instantiation
continues to work.
A good smoke test is to setup mqprio with,
# tc qdisc add dev eth4 root mqprio num_tc 8 \
map 0 1 2 3 4 5 6 7 \
queues 0@0 1@1 2@2 3@3 4@4 5@5 6@6 7@7
Fixes: e4c6734eaab9 ("net: rework ndo tc op to consume additional qdisc handle paramete")
Reported-by: Singh Krishneil <krishneil.k.singh@intel.com>
Reported-by: Jake Keller <jacob.e.keller@intel.com>
CC: Murali Karicheri <m-karicheri2@ti.com>
CC: Shradha Shah <sshah@solarflare.com>
CC: Or Gerlitz <ogerlitz@mellanox.com>
CC: Ariel Elior <ariel.elior@qlogic.com>
CC: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Don Skidmore <donald.c.skidmore@intel.com>
Signed-off-by: John Fastabend <john.r.fastabend@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fix a case of misleading code indentation.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
For consistency with other event data structs and to lessen
the chance of a mistake should one of the reserved fields become
used in the future, define the reserved fields as little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were no missing endianness conversions in this case, but the
fields of struct cfc_del_event_data should be defined as little-endian
to get rid of the ugly (__force __le32) casts.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It's not really a bug, but it was odd that bnx2x_eq_int() read the
message data as if it were a cfc_del_event regardless of the event type.
It's cleaner to access only the appropriate member of union event_data
after checking the event opcode.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On ppc64 the PF did not receive messages from VFs correctly.
Fields of struct vf_pf_event_data are little-endian.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When a VF is sending a message to the PF, it needs to trigger the PF
to tell it the message is ready.
The trigger did not work on ppc64. No interrupt appeared in the PF.
The bug is due to confusion about the layout of struct trigger_vf_zone.
In bnx2x_send_msg2pf() the trigger is written using writeb(), not
writel(), so the attempt to define the struct with a reversed layout on
big-endian is counter-productive.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
bnx2x crashes during the initialization of the 8021q module on ppc64.
The bug is a missing conversion from le32 in
bnx2x_handle_classification_eqe() when obtaining the cid value from
struct eth_event_data.
The fields in struct eth_event_data should all be declared as
little-endian and conversions added where missing.
Signed-off-by: Michal Schmidt <mschmidt@redhat.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When CONFIG_GENEVE is built as a loadable module, and bnx2x is built-in,
we get this link error:
drivers/net/built-in.o: In function `bnx2x_open':
:(.text+0x33322): undefined reference to `geneve_get_rx_port'
drivers/net/built-in.o: In function `bnx2x_sp_rtnl_task':
:(.text+0x3e632): undefined reference to `geneve_get_rx_port'
This avoids the problem by adding a separate Kconfig symbol named
CONFIG_BNX2X_GENEVE that is only enabled when the code is
reachable from the driver.
This is the same trick that BNX2X does for VXLAN support, and
is similar to how I40E handles both.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Fixes: 883ce97d25b0 ("bnx2x: Add Geneve inner-RSS support")
Acked-By: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Conflicts:
drivers/net/phy/bcm7xxx.c
drivers/net/phy/marvell.c
drivers/net/vxlan.c
All three conflicts were cases of simple overlapping changes.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Current initialization sequence is lacking, causing some configurations
to fail.
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Yuval Mintz <Yuval.Mintz@qlogic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
