summaryrefslogtreecommitdiff
path: root/drivers/net/ethernet/atheros
AgeCommit message (Collapse)Author
2012-04-19atl1c: threshold for ASPM is changed based on chip capabilityHuang, Xiong
threshold setting to control ASPM for diff chips are different. currently, all gigabit-capability chips have limited-ASPM under 100M throughput. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: restore max-read-request-size in Device Conrol RegisterHuang, Xiong
in some platforms, we found the max-read-request-size in Device Control Register is set to 0 by (BIOS?) during bootup, this will cause the performance(throughput) very bad. Restore it to a min-value. register definition of REG_DEVICE_CTRL is removed, using kernel API to access it as it's a standard pcie register. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: using fixed TXQ configuration for l2cb and l1cHuang, Xiong
using fixed TXQ config for l2cb and l1c regardless dmar_block to make tx-DMA more stable. register REG_TXQ_CTRL is refined as well. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove dmaw_blockHuang, Xiong
dmaw_block is never used in the driver, remove it. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: correct wrong definition of REG_DMA_CTRLHuang, Xiong
some fields of REG_DMA_CTRL(15C0) are wrong, replace with the newest one. haredware uses fixed dma-write-block size, remove dmaw_block related code in function atl1c_configure_dma. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: wrong register used to stop TXQHuang, Xiong
function atl1c_stop_mac uses wrong register of REG_TWSI_CTRL to stop mac, replace it with REG_TXQ_CTRL. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove code related to rxq 1/2/3Huang, Xiong
remove code related to rxq 1/2/3 since multi-q not support. refine REG_RXQ_CTRL definition as well. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: split 2 32bit registers of TPD to 4 16bit registersHuang, Xiong
TPD producer/consumer index is 16bit wide. 16bit read/write reduce the dependency of the 2 tpd rings (hi and lo) rename reg(157C/1580) to keep name coninsistency. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove SMB/CMB DMA related codeHuang, Xiong
l1c & later chips don't support DMA for SMB. CMB is removed from hardware. reg(15C8) is used to trig interrupt by tpd threshold. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove VPD registerHuang, Xiong
VPD register is only used for L1(devid=PCI_DEVICE_ID_ATTANSIC_L1) to access external NV-memory. l1c & later chip doesn't use it any more. PHY 0/1 registers occupy the last 2 slots of the dump table. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove HDS registerHuang, Xiong
remove HDS register as it doesn't exist in hardware. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: remove multiple-RX-Q codeHuang, Xiong
the multiple-RX-Q in hardware doesn't work, all related register definition & code are removed. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-18atl1c: update author contact info & company/driver desciptionHuang, Xiong
replace unavailable email of the author since he left with a mail-list. update company info as well, Atheros was acquired by Qualcomm. insert "100" to driver description since it support 100M controller. Signed-off-by: xiong <xiong@qca.qualcomm.com> Tested-by: Liu David <dwliu@qca.qualcomm.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-16atl1: remove unused member from atl1_adapter structureTony Zelenoff
Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/atheros/atlx/atl1.c drivers/net/ethernet/atheros/atlx/atl1.h Resolved a conflict between a DMA error bug fix and NAPI support changes in the atl1 driver. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: do not drop rx/tx interrupts before they are scheduledTony Zelenoff
To prevent interrupts lost they should be dropped only if they are scheduled via napi interfaces. In other case, there is exists situation when napi handler process TX interrupt, stay in RX processing and in that moment any other interrupt received. Then before this patch TX bit in ISR will be cleaned, napi schedule will not occur in case of currently processing event and TX interrupt definitely will be lost. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: do not process interrupts in cycle in handlerTony Zelenoff
As the rx/tx handled inside napi handler, the cycle is not needed now, because only the rx/tx need such kind of processing. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: enable errors and link ints when rx/tx scheduledTony Zelenoff
Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: add value to check ability of reenabling IRQsTony Zelenoff
Unfortunately it is not clear from code is usage of IMR register possible or not. So, to prevent possible side-effects of reading this register i prefer store interrupts enable flag separately. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: make function to set imr of cardTony Zelenoff
This function should be used later to set/remove proper bits in imr to disable only rx ints. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: use defined functions to disable irqTony Zelenoff
Looks like direct writes to IMR register is not good idea, because there are exist functions to make this work. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: add napi process of tx interruptsTony Zelenoff
Make the tx ints processing same as rx ones via napi. The idea got from e1000. The interrupt disabling is still not fine grained. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: make driver napi compatibleTony Zelenoff
This is first step, here there is no fine interrupt disabling which cause TX/ERR interrupts stalling when RX scheduled ints processed. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-15atl1: handle rx in separate conditionTony Zelenoff
Remove rx from unlikely optimization in case of rx is very likely thing for network card. This also reduce code a bit. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-13atl1: fix kernel panic in case of DMA errorsTony Zelenoff
Problem: There was two separate work_struct structures which share one handler. Unfortunately getting atl1_adapter structure from work_struct in case of DMA error was done from incorrect offset which cause kernel panics. Solution: The useless work_struct for DMA error removed and handler name changed to more generic one. Signed-off-by: Tony Zelenoff <antonz@parallels.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-04-07atl1e: stop using net_device.{base_addr, irq}.Francois Romieu
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com>
2012-04-07atl1c: stop using net_device.{base_addr, irq}.Francois Romieu
Signed-off-by: Francois Romieu <romieu@fr.zoreil.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com>
2012-03-19atlx: Use ETH_ALENJoe Perches
No need for yet another #define for this. Convert NODE_ADDRESS_SIZE use to ETH_ALEN and remove #define. Use memcpy instead of a loop to copy an address. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-03-09Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
2012-03-08atl1c: set ATL1C_WORK_EVENT_RESET bit correctlyDan Carpenter
ATL1C_WORK_EVENT_RESET is zero so the original code here is a nop. The intent was to set the zero bit. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-26Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/netDavid S. Miller
Conflicts: drivers/net/ethernet/sfc/rx.c Overlapping changes in drivers/net/ethernet/sfc/rx.c, one to change the rx_buf->is_page boolean into a set of u16 flags, and another to adjust how ->ip_summed is initialized. Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-19atl1c: dont use highprio tx queueEric Dumazet
This driver attempts to use two TX rings but lacks proper support : 1) IRQ handler only takes care of TX completion on first TX ring 2) the stop/start logic uses the legacy functions (for non multiqueue drivers) This means all packets witk skb mark set to 1 are sent through high queue but are never cleaned and queue eventualy fills and block the device, triggering the infamous "NETDEV WATCHDOG" message. Lets use a single TX ring to fix the problem, this driver is not a real multiqueue one yet. Minimal fix for stable kernels. Reported-by: Thomas Meyer <thomas@m3y3r.de> Tested-by: Thomas Meyer <thomas@m3y3r.de> Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-17atheros eth: set addr_assign_type if random_ether_addr() usedDanny Kukawka
Set addr_assign_type correctly to NET_ADDR_RANDOM in case a random MAC address was generated and assigned to the netdevice. Fix error handling in atl1c_probe(). If atl1c_read_mac_addr() couldn't get the hw mac address, and a random mac address get set return the error code. Don't go to err_eeprom in atl1c_probe(), use the generated MAC address in this case. Reset the state to NET_ADDR_PERM as soon as the MAC get changed via .ndo_set_mac_address. v2: use bitops Signed-off-by: Danny Kukawka <danny.kukawka@bisect.de> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-02-06netdev: ethernet dev_alloc_skb to netdev_alloc_skbPradeep A Dalvi
Replaced deprecating dev_alloc_skb with netdev_alloc_skb in drivers/net/ethernet - Removed extra skb->dev = dev after netdev_alloc_skb Signed-off-by: Pradeep A Dalvi <netdev@pradeepdalvi.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2012-01-31drivers/net: Remove alloc_etherdev error messagesJoe Perches
alloc_etherdev has a generic OOM/unable to alloc message. Remove the duplicative messages after alloc_etherdev calls. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-22Sweep away N/A fw_version dustbunnies from the .get_drvinfo routine of a ↵Rick Jones
number of drivers Per discussion with Ben Hutchings and David Miller, go through and remove assignments of "N/A" to fw_version in various drivers' .get_drvinfo routines. While there clean-up some use of bare constants and such. Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-16net: introduce and use netdev_features_t for device features setsMichał Mirosław
v2: add couple missing conversions in drivers split unexporting netdev_fix_features() implemented %pNF convert sock::sk_route_(no?)caps Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-11-08sweep the floors and convert some .get_drvinfo routines to strlcpyRick Jones
Per the mention made by Ben Hutchings that strlcpy is now the preferred string copy routine for a .get_drvinfo routine, do a bit of floor sweeping and convert some of the as-yet unconverted ethernet drivers to it. Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-25Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-nextLinus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next: (1745 commits) dp83640: free packet queues on remove dp83640: use proper function to free transmit time stamping packets ipv6: Do not use routes from locally generated RAs |PATCH net-next] tg3: add tx_dropped counter be2net: don't create multiple RX/TX rings in multi channel mode be2net: don't create multiple TXQs in BE2 be2net: refactor VF setup/teardown code into be_vf_setup/clear() be2net: add vlan/rx-mode/flow-control config to be_setup() net_sched: cls_flow: use skb_header_pointer() ipv4: avoid useless call of the function check_peer_pmtu TCP: remove TCP_DEBUG net: Fix driver name for mdio-gpio.c ipv4: tcp: fix TOS value in ACK messages sent from TIME_WAIT rtnetlink: Add missing manual netlink notification in dev_change_net_namespaces ipv4: fix ipsec forward performance regression jme: fix irq storm after suspend/resume route: fix ICMP redirect validation net: hold sock reference while processing tx timestamps tcp: md5: add more const attributes Add ethtool -g support to virtio_net ... Fix up conflicts in: - drivers/net/Kconfig: The split-up generated a trivial conflict with removal of a stale reference to Documentation/networking/net-modules.txt. Remove it from the new location instead. - fs/sysfs/dir.c: Fairly nasty conflicts with the sysfs rb-tree usage, conflicting with Eric Biederman's changes for tagged directories.
2011-10-19net: add skb frag size accessorsEric Dumazet
To ease skb->truesize sanitization, its better to be able to localize all references to skb frags size. Define accessors : skb_frag_size() to fetch frag size, and skb_frag_size_{set|add|sub}() to manipulate it. Signed-off-by: Eric Dumazet <eric.dumazet@gmail.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-07net: Remove unnecessary driver assignments of ethtool_ringparam fields to zeroRick Jones
Per comments from Ben Hutchings on a previous patch, sweep the floors a little removing unnecessary assignments of zero to fields of struct ethtool_ringparam in driver code supporting ethtool -g. Signed-off-by: Rick Jones <rick.jones2@hp.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-10-06net: use DMA_x_DEVICE and dma_mapping_error with skb_frag_dma_mapIan Campbell
When I converted some drivers from pci_map_page to skb_frag_dma_map I neglected to convert PCI_DMA_xDEVICE into DMA_x_DEVICE and pci_dma_mapping_error into dma_mapping_error. Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-09-16Merge branch 'master' of ../netdev-next/David S. Miller
2011-09-15MII: fix Kconfig dependencies for MIIJeff Kirsher
MII Kconfig option is apart of the core networking drivers and by default NET_CORE is enabled so drivers selecting MII will have MII enabled as well. It was found using the randconfig option during testing, MII would be selected but NET_CORE could be disabled. This caused a dependency error. Resolved the dependency by selecting NET_CORE when MII is selected. Reported-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Aaron Brown <aaron.f.brown@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-30atlx: convert to SKB paged frag API.Ian Campbell
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-30atl1e: convert to SKB paged frag API.Ian Campbell
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-30atl1c: convert to SKB paged frag API.Ian Campbell
Signed-off-by: Ian Campbell <ian.campbell@citrix.com> Cc: Jay Cliburn <jcliburn@gmail.com> Cc: Chris Snook <chris.snook@gmail.com> Cc: Jie Yang <jie.yang@atheros.com> Cc: netdev@vger.kernel.org Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-27drivers/net/ethernet/*: Enabled vendor Kconfig optionsJeff Kirsher
Based on finds for Stephen Rothwell, where current defconfig's enable a ethernet driver and it is not compiled due to the newly added NET_VENDOR_* component of Kconfig. This patch enables all the "new" Kconfig options so that current defconfig's will continue to compile the expected drivers. In addition, by enabling all the new Kconfig options does not add any un-expected options. CC: Stephen Rothwll <sfc@canb.auug.org.au> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
2011-08-17net: remove use of ndo_set_multicast_list in driversJiri Pirko
replace it by ndo_set_rx_mode Signed-off-by: Jiri Pirko <jpirko@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2011-08-11atl*: Move the Atheros driversJeff Kirsher
Move the Atheros drivers into drivers/net/ethernet/atheros/ and make the necessary Kconfig and Makefile changes. CC: Jay Cliburn <jcliburn@gmail.com> CC: Chris Snook <chris.snook@gmail.com> CC: Jie Yang <jie.yang@atheros.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-11 14:39:35 +0000