summaryrefslogtreecommitdiff
path: root/drivers/net/e1000e
AgeCommit message (Collapse)Author
2010-08-08e100/e1000*/igb*/ixgb*: Add missing read memory barrierJeff Kirsher
Based on patches from Sonny Rao and Milton Miller... Combined the patches to fix up clean_tx_irq and clean_rx_irq. The PowerPC architecture does not require loads to independent bytes to be ordered without adding an explicit barrier. In ixgbe_clean_rx_irq we load the status bit then load the packet data. With packet split disabled if these loads go out of order we get a stale packet, but we will notice the bad sequence numbers and drop it. The problem occurs with packet split enabled where the TCP/IP header and data are in different descriptors. If the reads go out of order we may have data that doesn't match the TCP/IP header. Since we use hardware checksumming this bad data is never verified and it makes it all the way to the application. This bug was found during stress testing and adding this barrier has been shown to fix it. The bug can manifest as a data integrity issue (bad payload data) or as a BUG in skb_pull(). This was a nasty bug to hunt down, if people agree with the fix I think it's a candidate for stable. Previously Submitted to e1000-devel only for ixgbe http://marc.info/?l=e1000-devel&m=126593062701537&w=3 We've now seen this problem hit with other device drivers (e1000e mostly) So I'm resubmitting with fixes for other Intel Device Drivers with similar issues. CC: Milton Miller <miltonm@bga.com> CC: Anton Blanchard <anton@samba.org> CC: Sonny Rao <sonnyrao@us.ibm.com> CC: stable <stable@kernel.org> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-04Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1443 commits) phy/marvell: add 88ec048 support igb: Program MDICNFG register prior to PHY init e1000e: correct MAC-PHY interconnect register offset for 82579 hso: Add new product ID can: Add driver for esd CAN-USB/2 device l2tp: fix export of header file for userspace can-raw: Fix skb_orphan_try handling Revert "net: remove zap_completion_queue" net: cleanup inclusion phy/marvell: add 88e1121 interface mode support u32: negative offset fix net: Fix a typo from "dev" to "ndev" igb: Use irq_synchronize per vector when using MSI-X ixgbevf: fix null pointer dereference due to filter being set for VLAN 0 e1000e: Fix irq_synchronize in MSI-X case e1000e: register pm_qos request on hardware activation ip_fragment: fix subtracting PPPOE_SES_HLEN from mtu twice net: Add getsockopt support for TCP thin-streams cxgb4: update driver version cxgb4: add new PCI IDs ... Manually fix up conflicts in: - drivers/net/e1000e/netdev.c: due to pm_qos registration infrastructure changes - drivers/net/phy/marvell.c: conflict between adding 88ec048 support and cleaning up the IDs - drivers/net/wireless/ipw2x00/ipw2100.c: trivial ipw2100_pm_qos_req conflict (registration change vs marking it static)
2010-08-03e1000e: correct MAC-PHY interconnect register offset for 82579Bruce Allan
The MAC-PHY interconnect register set on ICH/PCH parts is accessed through a peephole mechanism by writing an offset to a CSR register. The offset for the interconnect's half-duplex control register (which is used in a jumbo frame workaround for 82579) is incorrect. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02Merge branch 'master' of ↵David S. Miller
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6 Conflicts: drivers/net/e1000e/hw.h net/bridge/br_device.c net/bridge/br_input.c
2010-08-02e1000e: Fix irq_synchronize in MSI-X caseJeff Kirsher
Based on original patch/work from Jean Delvare <jdelvare@suse.de> Synchronize all IRQs when in MSI-X IRQ mode. Jean's original patch hard coded the sync with the 3 possible vectors, this patch incorporates more flexibility for the future and aligns with how igb stores the number of vectors into the adapter structure. CC: Jean Delvare <jdelvare@suse.de> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-08-02e1000e: register pm_qos request on hardware activationFlorian Mickler
The pm_qos_add_request call has to register the pm_qos request with the pm_qos susbsystem before first use of the pm_qos request via pm_qos_update_request. As pm_qos changed to use plists there is no benefit in registering and unregistering the pm_qos request on ifup/ifdown and thus we move the registering into e1000_open and the unregistering in e1000_close. This fixes the following warning: [ 1.786060] WARNING: at kernel/pm_qos_params.c:264 pm_qos_update_request+0x28/0x54() [ 1.786088] Hardware name: Latitude E6500 [ 1.787045] pm_qos_update_request() called for unknown object [ 1.787966] Modules linked in: [ 1.788940] Pid: 1, comm: swapper Not tainted 2.6.35-rc5-mmotm0719 #1 [ 1.790035] Call Trace: [ 1.791121] [<ffffffff81037335>] warn_slowpath_common+0x80/0x98 [ 1.792205] [<ffffffff810373e1>] warn_slowpath_fmt+0x41/0x43 [ 1.793279] [<ffffffff81057c14>] pm_qos_update_request+0x28/0x54 [ 1.794347] [<ffffffff8134889e>] e1000_configure+0x421/0x459 [ 1.795393] [<ffffffff8134afbd>] e1000_open+0xbd/0x37c [ 1.796436] [<ffffffff8105743a>] ? raw_notifier_call_chain+0xf/0x11 [ 1.797491] [<ffffffff8145f948>] __dev_open+0xae/0xe2 [ 1.798547] [<ffffffff8145f997>] dev_open+0x1b/0x49 [ 1.799612] [<ffffffff8146e36e>] netpoll_setup+0x84/0x259 [ 1.800685] [<ffffffff81b5037c>] init_netconsole+0xbc/0x21f [ 1.801744] [<ffffffff81b5026c>] ? sir_wq_init+0x0/0x35 [ 1.802793] [<ffffffff81b502c0>] ? init_netconsole+0x0/0x21f [ 1.803845] [<ffffffff810002ff>] do_one_initcall+0x7a/0x12f [ 1.804885] [<ffffffff81b2ccae>] kernel_init+0x138/0x1c2 [ 1.805915] [<ffffffff81003554>] kernel_thread_helper+0x4/0x10 [ 1.806937] [<ffffffff81590e00>] ? restore_args+0x0/0x30 [ 1.807955] [<ffffffff81b2cb76>] ? kernel_init+0x0/0x1c2 [ 1.808958] [<ffffffff81003550>] ? kernel_thread_helper+0x0/0x10 [ 1.809958] ---[ end trace 84b562a00a60539e ]--- Signed-off-by: Florian Mickler <florian@mickler.org> Tested-by: Valdis Kletnieks <valdis.kletnieks@vt.edu> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-27e1000e: 82577/82578 PHY register access issuesBruce Allan
The MAC-PHY interconnect on 82577/82578 uses a power management feature (called K1) which must be disabled when in 1Gbps due to a hardware issue on these parts. The #define bit setting used to enable/disable K1 is incorrect and can cause PHY register accesses to stop working altogether until the next device reset. This patch sets the register correctly. This issue is present in kernels since 2.6.32. CC: stable@kernel.org Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-26e1000e: Drop a useless statementJean Delvare
err is set again a few lines below. Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jean Delvare <jdelvare@suse.de> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-07-19pm_qos: Get rid of the allocation in pm_qos_add_request()James Bottomley
All current users of pm_qos_add_request() have the ability to supply the memory required by the pm_qos routines, so make them do this and eliminate the kmalloc() with pm_qos_add_request(). This has the double benefit of making the call never fail and allowing it to be called from atomic context. Signed-off-by: James Bottomley <James.Bottomley@suse.de> Signed-off-by: mark gross <markgross@thegnar.org> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-06-29e1000e: disable EEE support by defaultBruce Allan
Based on community feedback, EEE should be disabled by default until the IEEE802.3az specification has been finalized. Cc: bhutchings@solarflare.com Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29e1000e: remove EEE module parameterBruce Allan
As requested by Dave Miller. A follow-on set of patches will allow for ethtool to enable/disable the feature instead. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29e1000e: suppress compile warnings on certain archsBruce Allan
Commit 84f4ee902ad3ee964b7b3a13d5b7cf9c086e9916 causes compile warnings on architectures that have unsigned long long's that are not 64-bit, e.g. ia64. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29e1000e: don't inadvertently re-set INTX_DISABLEDean Nelson
Should e1000_test_msi() fail to see an msi interrupt, it attempts to fallback to legacy INTx interrupts. But an error in the code may prevent this from happening correctly. Before calling e1000_test_msi_interrupt(), e1000_test_msi() disables SERR by clearing the SERR bit from the just read PCI_COMMAND bits as it writes them back out. Upon return from calling e1000_test_msi_interrupt(), it re-enables SERR by writing out the version of PCI_COMMAND it had previously read. The problem with this is that e1000_test_msi_interrupt() calls pci_disable_msi(), which eventually ends up in pci_intx(). And because pci_intx() was called with enable set to 1, the INTX_DISABLE bit gets cleared from PCI_COMMAND, which is what we want. But when we get back to e1000_test_msi(), the INTX_DISABLE bit gets inadvertently re-set because of the attempt by e1000_test_msi() to re-enable SERR. The solution is to have e1000_test_msi() re-read the PCI_COMMAND bits as part of its attempt to re-enable SERR. During debugging/testing of this issue I found that not all the systems I ran on had the SERR bit set to begin with. And on some of the systems the same could be said for the INTX_DISABLE bit. Needless to say these latter systems didn't have a problem falling back to legacy INTx interrupts with the code as is. Signed-off-by: Dean Nelson <dnelson@redhat.com> CC: stable@kernel.org Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-29e1000e: fail when try to setup unsupported featuresStanislaw Gruszka
Signed-off-by: Stanislaw Gruszka <sgruszka@redhat.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: disable gig speed when in S0->Sx transitionBruce Allan
Most of this workaround is necessary for all ICHx/PCH parts so one of the two MAC-type checks can be removed. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: packet split should not be used with early receiveBruce Allan
Originally it was thought there were issues with ICHx/PCH parts with packet split when jumbo frames were enabled but in fact it is really only when early-receive is enabled (via ERT register) on these parts. Use packet split with jumbos but only when early-receive is not enabled. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: do not touch PHY page 800 registers when link speed is 1000MbpsBruce Allan
The PHY on 82577/82578 has issues when the registers on page 800 are accessed when in gigabit mode. Do not clear the Wakeup Control register when resetting the part since it is on page 800 (and will be cleared on reset anyway). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-23e1000e: avoid polling h/w registers during link negotiationBruce Allan
Avoid touching hardware registers when possible, otherwise link negotiation can get messed up when user-level scripts are rapidly polling the driver to see if/when link is up. Use the saved link state information instead when possible. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: update driver version numberBruce Allan
Also separate out an _EXTRAVERSION similar to the core kernel. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: update copyright informationBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: enable support for EEE on 82579Bruce Allan
This patch enables IEEE802.3az (a.k.a. Energy Efficient Ethernet) on the new 82579 LOMs. An optional module parameter is provided to disable the feature if desired. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: initial support for 82579 LOMsBruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: fix check for manageability on ICHx/PCHBruce Allan
Do not check for all the bits in E1000_FWSM_MODE_MASK when checking for manageability on 82577/82578; only check if iAMT is enabled. Both of the manageability checks (for 82577/82578 and ICHx) must check the firmware valid bit too since the other bits are only valid when the latter is set. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: separate out PHY statistics register updatesBruce Allan
The 82577/82578 parts have half-duplex statistics in PHY registers. These need only be read when in half-duplex and should all be read at once rather than one at a time to prevent excessive cycles of acquiring/releasing the PHY semaphore. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan
Do not acquire and release the PHY unnecessarily for parts that return from this workaround without actually accessing the PHY registers. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Jeff Pieper <jeffrey.e.pieper@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-18e1000e: cleanup ethtool loopback setup codeBruce Allan
Refactor the loopback setup code to first handle the only 10/100 PHY supported by the driver if applicable and then handle the 1Gig PHYs in a switch statement for PHY-specific setups. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Tested-by: Emil Tantilov <emil.s.tantilov@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-06-03e1000e: change logical negate to bitwiseDan Carpenter
The bitwise negate is intended here. With the logical negate the condition is always false. Signed-off-by: Dan Carpenter <error27@gmail.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-20Merge git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6Linus Torvalds
* git://git.kernel.org/pub/scm/linux/kernel/git/davem/net-next-2.6: (1674 commits) qlcnic: adding co maintainer ixgbe: add support for active DA cables ixgbe: dcb, do not tag tc_prio_control frames ixgbe: fix ixgbe_tx_is_paused logic ixgbe: always enable vlan strip/insert when DCB is enabled ixgbe: remove some redundant code in setting FCoE FIP filter ixgbe: fix wrong offset to fc_frame_header in ixgbe_fcoe_ddp ixgbe: fix header len when unsplit packet overflows to data buffer ipv6: Never schedule DAD timer on dead address ipv6: Use POSTDAD state ipv6: Use state_lock to protect ifa state ipv6: Replace inet6_ifaddr->dead with state cxgb4: notify upper drivers if the device is already up when they load cxgb4: keep interrupts available when the ports are brought down cxgb4: fix initial addition of MAC address cnic: Return SPQ credit to bnx2x after ring setup and shutdown. cnic: Convert cnic_local_flags to atomic ops. can: Fix SJA1000 command register writes on SMP systems bridge: fix build for CONFIG_SYSFS disabled ARCNET: Limit com20020 PCI ID matches for SOHARD cards ... Fix up various conflicts with pcmcia tree drivers/net/ {pcmcia/3c589_cs.c, wireless/orinoco/orinoco_cs.c and wireless/orinoco/spectrum_cs.c} and feature removal (Documentation/feature-removal-schedule.txt). Also fix a non-content conflict due to pm_qos_requirement getting renamed in the PM tree (now pm_qos_request) in net/mac80211/scan.c
2010-05-14drivers/net: Remove unnecessary returns from void function()sJoe Perches
This patch removes from drivers/net/ all the unnecessary return; statements that precede the last closing brace of void functions. It does not remove the returns that are immediately preceded by a label as gcc doesn't like that. It also does not remove null void functions with return. Done via: $ grep -rP --include=*.[ch] -l "return;\n}" net/ | \ xargs perl -i -e 'local $/ ; while (<>) { s/\n[ \t\n]+return;\n}/\n}/g; print; }' with some cleanups by hand. Compile tested x86 allmodconfig only. Signed-off-by: Joe Perches <joe@perches.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: add PCI device id to enable support for 82567V-4Bruce Allan
Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: Fix/cleanup PHY reset code for ICHx/PCHxBruce Allan
i) Fixes a bug where e1000_sw_lcd_config_ich8lan() was calling e1000_lan_init_done_ich8lan() to poll the STATUS.LAN_INIT_DONE bit to make sure the MAC had completed the PHY configuration. However, e1000_lan_init_done_ich8lan() had already been called in one of the two places where PHY reset occurs for ICHx/PCHx parts, which caused the second call to busy-wait for 150 msec because the LAN_INIT_DONE bit had already been checked and cleared. ii) Cleanup the two separate PHY reset code paths, i.e. the full-chip reset in e1000_reset_hw_ich8lan() and the PHY-only reset in e1000_phy_hw_reset_ich8lan(). There was duplicate code in both paths to be performed post-reset that are now combined into one new function - e1000_post_phy_reset_ich8lan(). This cleanup also included moving the clearing of the PHY Reset Asserted bit in the STATUS register (now done for all ICH/PCH parts) and the check for the indication from h/w that basic configuration has completed back to where it previously was in e1000_get_cfg_done_ich8lan(). iii) Corrected a few comments Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: move settting of flow control refresh timer to link setup codeBruce Allan
The flow control refresh timer value needs to be saved off so that it can be programmed into the approrpiate register when applicable but without a reset, e.g. when changing flow control parameters via ethtool. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: fix checks for manageability enabled and management pass-throughBruce Allan
The mac->arc_subsystem was being incorrectly used to flag whether or not manageability was enabled when it should only be used to state whether the ARC (Host interface) subsystem is available on a particular MAC _and_ only valid when any manageability is enabled. The ARC subsystem is currently only available on 80003es2lan and 82573 parts supported by the driver. A new flag, has_fwsm, is introduced to be used when checking if manageability is enabled but only on parts that acutally have an FWSM register. While the above parts have an FWSM register, there are other parts that have FWSM but do not have support for the ARC subsystem, namely 82571/2 and ICHx/PCH. And then there are parts that have manageability, but do not have either FWSM register or support for the ARC subsystem - these are 82574 and 82583. For 80003es2lan, 82571/2/3 and ICH/PCH parts, this patch makes no functional changes, it only corrects the usage of the manageability flags. For 82574 and 82583, it fixes the incorrect accesses of the non-existent FWSM register and ARC subsystem as well as corrects the check for management pass-through. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: Incorrect function pointer set for force_speed_duplex on 82577Bruce Allan
The force_speed_duplex function pointer was incorrectly set. Instead of calling the 82577-specific version it was calling the m88 version which, among other incorrect things, reset the PHY causing autonegotiation to be re-enabled in the PHY resulting in the link defaulting to half-duplex. The 82577-specific force_speed_duplex function also had an issue where it disabled Auto-MDI-X which caused the link to not come up. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: Cleanup e1000_sw_lcd_config_ich8lan()Bruce Allan
After every reset all ICH/PCH parts call this function which acquires the swflag, performs a workaround on applicable parts and releases the swflag. There is no reason for parts for which this workaround is not applicable to acquire and release the swflag so the function should just return without doing anything for these parts. This also provides for the indentation of most of the function contents to be shifted left cleaning up the code. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: Remove EN_MAC_ADDR_FILTER check from enable_mng_pass_thru checkBruce Allan
Patch addresses issues when manageability passthrough is enabled, but the MAC_ADDR_FILTER bit is not set in the MANC register. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: cleanup multiple common exit pointsBruce Allan
...in e1000_update_nvm_checksum_ich8lan(). Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: s/w initiated LSC MSI-X interrupts not generated; no transmitBruce Allan
In MSI-X mode when an IMPI SoL session was active (i.e. the PHY reset was blocked), the LSC interrupt generated by s/w to start the watchdog which started the transmitter was not getting fired by the hardware because bit 24 (the 'other' cause bit) also needed to be set. Without an active SoL session, the PHY was reset which caused the h/w to fire the LSC interrupt. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: initialize manageability (IPMI) pass-through in 82574/82583Bruce Allan
82574/82583 uses different registers/bits to setup manageability filters than all other parts supported by e1000e; set them accordingly for IPMI pass-through. Rename the function to better reflect what it does. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: bad state after running ethtool diagnostics with AMT enabledBruce Allan
When running ethtool online diagnostics with no open interface, there is a short period of time where the driver relinquishes control of the adapter during which time AMT (manageability firmware) can put the adapter into an unknown state resulting in such things as link test failure, hardware hang, reporting an incorrect link speed, etc. Resetting the adapter during an open() resolves this by putting the adapter into a quiescent state. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-12e1000e: use static params to save stack space (part 2)Bruce Allan
A couple stack cleanups missed in an earlier patch from Jesse. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Cc: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-10PM QOS updateMark Gross
This patch changes the string based list management to a handle base implementation to help with the hot path use of pm-qos, it also renames much of the API to use "request" as opposed to "requirement" that was used in the initial implementation. I did this because request more accurately represents what it actually does. Also, I added a string based ABI for users wanting to use a string interface. So if the user writes 0xDDDDDDDD formatted hex it will be accepted by the interface. (someone asked me for it and I don't think it hurts anything.) This patch updates some documentation input I got from Randy. Signed-off-by: markgross <mgross@linux.intel.com> Signed-off-by: Rafael J. Wysocki <rjw@sisk.pl>
2010-05-06e1000e: Reset 82577/82578 PHY before first PHY register readBruce Allan
Reset the PHY before first accessing it. Doing so, ensure that the PHY is in a known good state before we read/write PHY registers. This fixes a driver probe failure. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-06e1000e: reset MAC-PHY interconnect on 82577/82578 during Sx->S0Bruce Allan
During Sx->S0 transitions, the interconnect between the MAC and PHY on 82577/82578 can remain in SMBus mode instead of transitioning to the PCIe-like mode required during normal operation. Toggling the LANPHYPC Value bit essentially resets the interconnect forcing it to the correct mode. Signed-off-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000/e1000e: implement a simple interrupt moderationJesse Brandeburg
Back before e1000-7.3.20, the e1000 driver had a simple algorithm that managed interrupt moderation. The driver was updated in 7.3.20 to have the new "adaptive" interrupt moderation but we have customer requests to redeploy the old way as an option. This patch adds the old functionality back. The new functionality can be enabled via module parameter or at runtime via ethtool. Module parameter: (InterruptThrottleRate=4) to use this new moderation method. Ethtool method: ethtool -C ethX rx-usecs 4 Signed-off-by: Jesse Brandeburg <jesse.brandeburg@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: increase rx fifo size to 36K on 82574 and 82583Alexander Duyck
This change increases the RX fifo size to 36K for standard frames and decreases the TX fifo size to 4K. The reason for this change is that on slower systems the RX is much more likely to backfill and need space than the TX is. As long as the TX fifo is twice the size of the MTU we should have more than enough TX fifo. Signed-off-by: Alexander Duyck <alexander.h.duyck@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: Save irq into netdev structureTom Herbert
Set net->devirq to pdev->irq. This should be consistent with other drivers. Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: Remove unnessary log messageTom Herbert
Remove e_info message printed whenever TSO is enabled or disabled. This is not very useful and just clutters dmesg. Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: reduce writes of RX producer ptrTom Herbert
Reduce number of writes to RX producer pointer. When alloc'ing RX buffers, only write the RX producer pointer once every E1000_RX_BUFFER_WRITE (16) buffers created. Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
2010-05-05e1000e: save skb counts in TX to avoid cache missesTom Herbert
In e1000_tx_map, precompute number of segements and bytecounts which are derived from fields in skb; these are stored in buffer_info. When cleaning tx in e1000_clean_tx_irq use the values in the associated buffer_info for statistics counting, this eliminates cache misses on skb fields. Signed-off-by: Tom Herbert <therbert@google.com> Acked-by: Bruce Allan <bruce.w.allan@intel.com> Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com> Signed-off-by: David S. Miller <davem@davemloft.net>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-21 23:25:49 +0000