| Age | Commit message (Collapse) | Author |
|---|
|
Allow the special tag in ingress only on the CPU port and not on all
ports. A packet with a special tag could circumvent the hardware
forwarding and should only be allowed on the CPU port where Linux
controls the port.
Fixes: 14fceff4771e ("net: dsa: Add Lantiq / Intel DSA driver for vrx200)"
Signed-off-by: Hauke Mehrtens <hauke@hauke-m.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While not explicitly documented as supported in UM10944, compliance with
the STP states can be obtained by manipulating 3 settings at the
(per-port) MAC config level: dynamic learning, inhibiting reception of
regular traffic, and inhibiting transmission of regular traffic.
In all these modes, transmission and reception of special BPDU frames
from the stack is still enabled (not inhibited by the MAC-level
settings).
On ingress, BPDUs are classified by the MAC filter as link-local
(01-80-C2-00-00-00) and forwarded to the CPU port. This mechanism works
under all conditions (even without the custom 802.1Q tagging) because
the switch hardware inserts the source port and switch ID into bytes 4
and 5 of the MAC-filtered frames. Then the DSA .rcv handler needs to put
back zeroes into the MAC address after decoding the source port
information.
On egress, BPDUs are transmitted using management routes from the xmit
worker thread. Again this does not require switch tagging, as the switch
port is programmed through SPI to hold a temporary (single-fire) route
for a frame with the programmed destination MAC (01-80-C2-00-00-00).
STP is activated using the following commands and was tested by
connecting two front-panel ports together and noticing that switching
loops were prevented (one port remains in the blocking state):
$ ip link add name br0 type bridge stp_state 1 && ip link set br0 up
$ for eth in $(ls /sys/devices/platform/soc/2100000.spi/spi_master/spi0/spi0.1/net/);
do ip link set ${eth} master br0 && ip link set ${eth} up; done
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In order to support this, we are creating a make-shift switch tag out of
a VLAN trunk configured on the CPU port. Termination of normal traffic
on switch ports only works when not under a vlan_filtering bridge.
Termination of management (PTP, BPDU) traffic works under all
circumstances because it uses a different tagging mechanism
(incl_srcpt). We are making use of the generic CONFIG_NET_DSA_TAG_8021Q
code and leveraging it from our own CONFIG_NET_DSA_TAG_SJA1105.
There are two types of traffic: regular and link-local.
The link-local traffic received on the CPU port is trapped from the
switch's regular forwarding decisions because it matched one of the two
DMAC filters for management traffic.
On transmission, the switch requires special massaging for these
link-local frames. Due to a weird implementation of the switching IP, by
default it drops link-local frames that originate on the CPU port.
It needs to be told where to forward them to, through an SPI command
("management route") that is valid for only a single frame.
So when we're sending link-local traffic, we are using the
dsa_defer_xmit mechanism.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The Marvell SOHO switches have several ways to access the internal
registers. One of them being the System Management Interface (SMI),
using the MDC and MDIO pins, with direct and indirect variants.
In preparation for adding support for other register accesses, move
the SMI code into its own files. At the same time, refine the code
to make it clear that the indirect variant is implemented using the
direct variant accessing only two registers for command and data.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Allow an interrupt number to be passed in the platform data. The
driver will then use it if not zero, otherwise it will poll for
interrupts.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If the NO_CPU strap is set, the switch starts in 'dumb hub' mode, with
all ports enable. Ports which are then actively used are reconfigured
as required when the driver starts. However unused ports are left
alone. Change this to disable them, and turn off any SERDES
interface. This could save some power and so reduce the temperature a
bit.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When requested to disable a port, set the port STP state to disabled.
This fully disables the port and should save some power.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ethernet flow control:
The switch MAC does not consume, nor does it emit pause frames. It
simply forwards them as any other Ethernet frame (and since the DMAC is,
per IEEE spec, 01-80-C2-00-00-01, it means they are filtered as
link-local traffic and forwarded to the CPU, which can't do anything
useful with them).
Duplex:
There is no duplex setting in the SJA1105 MAC. It is known to forward
traffic at line rate on the same port in both directions. Therefore it
must be that it only supports full duplex.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Resetting the switch at runtime is currently done while changing the
vlan_filtering setting (due to the required TPID change).
But reset is asynchronous with packet egress, and the switch core will
not wait for egress to finish before carrying on with the reset
operation.
As a result, a connected PHY such as the BCM5464 would see an
unterminated Ethernet frame and start to jabber (repeat the last seen
Ethernet symbols - jabber is by definition an oversized Ethernet frame
with bad FCS). This behavior is strange in itself, but it also causes
the MACs of some link partners (such as the FRDM-LS1012A) to completely
lock up.
So as a remedy for this situation, when switch reset is required, simply
inhibit Tx on all ports, and wait for the necessary time for the
eventual one frame left in the egress queue (not even the Tx inhibit
command is instantaneous) to be flushed.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If STP is active, this setting is applied on bridged ports each time an
Ethernet link is established (topology changes).
Since the setting is global to the switch and a reset is required to
change it, resets are prevented if the new callback does not change the
value that the hardware already is programmed for.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filtering cannot be properly disabled in SJA1105. So in order to
emulate the "no VLAN awareness" behavior (not dropping traffic that is
tagged with a VID that isn't configured on the port), we need to hack
another switch feature: programmable TPID (which is 0x8100 for 802.1Q).
We are reprogramming the TPID to a bogus value which leaves the switch
thinking that all traffic is untagged, and therefore accepts it.
Under a vlan_filtering bridge, the proper TPID of ETH_P_8021Q is
installed again, and the switch starts identifying 802.1Q-tagged
traffic.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Documentation/devicetree/bindings/net/ethernet.txt is confusing because
it says what the MAC should not do, but not what it *should* do:
* "rgmii-rxid" (RGMII with internal RX delay provided by the PHY, the MAC
should not add an RX delay in this case)
The gap in semantics is threefold:
1. Is it illegal for the MAC to apply the Rx internal delay by itself,
and simplify the phy_mode (mask off "rgmii-rxid" into "rgmii") before
passing it to of_phy_connect? The documentation would suggest yes.
1. For "rgmii-rxid", while the situation with the Rx clock skew is more
or less clear (needs to be added by the PHY), what should the MAC
driver do about the Tx delays? Is it an implicit wild card for the
MAC to apply delays in the Tx direction if it can? What if those were
already added as serpentine PCB traces, how could that be made more
obvious through DT bindings so that the MAC doesn't attempt to add
them twice and again potentially break the link?
3. If the interface is a fixed-link and therefore the PHY object is
fixed (a purely software entity that obviously cannot add clock
skew), what is the meaning of the above property?
So an interpretation of the RGMII bindings was chosen that hopefully
does not contradict their intention but also makes them more applied.
The SJA1105 driver understands to act upon "rgmii-*id" phy-mode bindings
if the port is in the PHY role (either explicitly, or if it is a
fixed-link). Otherwise it always passes the duty of setting up delays to
the PHY driver.
The error behavior that this patch adds is required on SJA1105E/T where
the MAC really cannot apply internal delays. If the other end of the
fixed-link cannot apply RGMII delays either (this would be specified
through its own DT bindings), then the situation requires PCB delays.
For SJA1105P/Q/R/S, this is however hardware supported and the error is
thus only temporary. I created a stub function pointer for configuring
delays per-port on RXC and TXC, and will implement it when I have access
to a board with this hardware setup.
Meanwhile do not allow the user to select an invalid configuration.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Currently only the (more difficult) first generation E/T series is
supported. Here the TCAM is only 4-way associative, and to know where
the hardware will search for a FDB entry, we need to perform the same
hash algorithm in order to install the entry in the correct bin.
On P/Q/R/S, the TCAM should be fully associative. However the SPI
command interface is different, and because I don't have access to a
new-generation device at the moment, support for it is TODO.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
At this moment the following is supported:
* Link state management through phylib
* Autonomous L2 forwarding managed through iproute2 bridge commands.
IP termination must be done currently through the master netdevice,
since the switch is unmanaged at this point and using
DSA_TAG_PROTO_NONE.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Signed-off-by: Georg Waibel <georg.waibel@sensor-technik.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Three trivial overlapping conflicts.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that the driver can be probed as an mdio device, remove the legacy
DSA platform device probing.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Probing DSA devices as platform devices has been superseded by using
normal bus drivers. Add support for probing the mv88e6060 device as an
mdio device.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This was recently introduced, so keeping state inside the driver is no
longer necessary.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The driver, recognizing that the .port_vlan_filtering callback was never
coming after the port left its parent bridge, decided to take that duty
in its own hands. DSA now takes care of this condition, so fix that.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA core is now able to do this check prior to calling the
.port_vlan_filtering callback, so tell it that VLAN filtering is global
for this particular hardware.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "fs->location" is a u32 that comes from the user in ethtool_set_rxnfc().
We can't pass unclamped values to test_bit() or it results in an out of
bounds access beyond the end of the bitmap.
Fixes: 7318166cacad ("net: dsa: bcm_sf2: Add support for ethtool::rxnfc")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Remove the legacy method of probing the mv88e6xxx driver, now that all
the mainline boards have been converted to use mdio based probing for
a number of cycles.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The REG_READ macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The REG_WRITE macro contains a return statement, making it not very
safe. Remove it by inlining the code.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Pass around priv, not ds. This will help with changing to an mdio
driver, and makes this driver more like mv88e6xxx.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add an SPDX header, and remove the license text.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
phylink will call the mac_config() callback once per second when
polling a PHY or a fixed link. The MAC driver is not supposed to
reconfigure the MAC if nothing has changed.
Make the mv88e6xxx driver look at the current configuration of the
port, and return early if nothing has changed.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Minor comment merge conflict in mlx5.
Staging driver has a fixup due to the skb->xmit_more changes
in 'net-next', but was removed in 'net'.
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation to enabling -Wimplicit-fallthrough, mark switch cases
where we are expecting to fall through.
This patch fixes the following warning:
drivers/net/dsa/microchip/ksz9477.c: In function ‘ksz9477_get_interface’:
drivers/net/dsa/microchip/ksz9477.c:1145:6: warning: this statement may fall through [-Wimplicit-fallthrough=]
if (gbit)
^
drivers/net/dsa/microchip/ksz9477.c:1147:2: note: here
case 0:
^~~~
Warning level 3 was used: -Wimplicit-fallthrough=3
This patch is part of the ongoing efforts to enable
-Wimplicit-fallthrough.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patches fixes few issues in mv88e6390x_port_set_cmode().
1. When entering the function the old cmode may be 0, in this case
mv88e6390x_serdes_get_lane() returns -ENODEV. As result we bail
out and have no chance to set a new mode. Therefore deal properly
with -ENODEV.
2. Once we have disabled power and irq, let's set the cached cmode to 0.
This reflects the actual status and is cleaner if we bail out with an
error in the following function calls.
3. The cached cmode is used by mv88e6390x_serdes_get_lane(),
mv88e6390_serdes_power_lane() and mv88e6390_serdes_irq_enable().
Currently we set the cached mode to the new one at the very end of
the function only, means until then we use the old one what may be
wrong.
4. When calling mv88e6390_serdes_irq_enable() we use the lane value
belonging to the old cmode. Get the lane belonging to the new cmode
before calling this function.
It's hard to provide a good "Fixes" tag because quite a few smaller
changes have been done to the code in question recently.
Fixes: d235c48b40d3 ("net: dsa: mv88e6xxx: power serdes on/off for 10G interfaces on 6390X")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
This partially reverts ed8fe20205ac ("net: dsa: mv88e6xxx: prevent
interrupt storm caused by mv88e6390x_port_set_cmode"). I missed
that chip->ports[].cmode is overwritten anyway by the cmode
caching in mv88e6xxx_setup().
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch implements accessors for the QCA8337 MDIO access
through the MDIO_MASTER register, which makes it possible to
access the PHYs on slave-bus through the switch. In cases
where the switch ports are already mapped via external
"phy-phandles", the internal mdio-bus is disabled in order to
prevent a duplicated discovery and enumeration of the same
PHYs. Don't use mixed external and internal mdio-bus
configurations, as this is not supported by the hardware.
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This belated patch implements Andrew Lunn's request of
"remove the phy_read() and phy_write() functions."
<https://lore.kernel.org/patchwork/comment/902734/>
While seemingly harmless, this causes the switch's user
port PHYs to get registered twice. This is because the
DSA subsystem will create a slave mdio-bus not knowing
that the qca8k_phy_(read|write) accessors operate on
the external mdio-bus. So the same "bus" gets effectively
duplicated.
Cc: stable@vger.kernel.org
Fixes: 6b93fb46480a ("net-next: dsa: add new driver for qca8xxx family")
Signed-off-by: Christian Lamparter <chunkeey@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since commit ad67b74d2469 ("printk: hash addresses printed with %p")
pointers are being hashed when printed. Displaying the virtual memory at
bootup time is not helpful, we use a dev_info() print which already
displays the platform device's address.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
By default, the switch driver is expected to configure CPU and DSA
ports to their maximum speed. For the 6341 and 6390 families, the
ports interface mode has to be configured as well. The 6390X range
support 10G ports using XAUI, while the 6341 and 6390 supports
2500BaseX, as their maximum speed.
Fixes: 787799a9d555 ("net: dsa: mv88e6xxx: Default ports 9/10 6390X CMODE to 1000BaseX")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
DSA framework
In the original patch I missed to add mv88e6xxx_ports_cmode_init()
to the second probe function, the one for the new DSA framework.
Fixes: ed8fe20205ac ("net: dsa: mv88e6xxx: prevent interrupt storm caused by mv88e6390x_port_set_cmode")
Reported-by: Shaokun Zhang <zhangshaokun@hisilicon.com>
Suggested-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYs
If an external PHY is connected via SGMII and uses in-band signalling
then the auto-negotiated values aren't propagated to the port,
resulting in a broken link. See discussion in [0]. This patch adds
this propagation. We need to call mv88e6xxx_port_setup_mac(),
therefore export it from chip.c.
Successfully tested on a ZII DTU with 88E6390 switch and an
Aquantia AQCS109 PHY connected via SGMII to port 9.
[0] https://marc.info/?t=155130287200001&r=1&w=2
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Ports 9 and 10 don't have internal PHY's but are (dependent on the
version) SERDES/SGMII/XAUI/RXAUI ports.
v2:
- fix it for all 88E6x90 family members
Fixes: bc3931557d1d ("net: dsa: mv88e6xxx: Add number of internal PHYs")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
mv88e6xxx_port_set_duplex
When testing another issue I faced the problem that
mv88e6xxx_port_setup_mac() failed due to DUPLEX_UNKNOWN being passed
as argument to mv88e6xxx_port_set_duplex(). We should handle this case
gracefully and return -EOPNOTSUPP, like e.g. mv88e6xxx_port_set_speed()
is doing it.
Fixes: 7f1ae07b51e8 ("net: dsa: mv88e6xxx: add port duplex setter")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add KSZ9893 switch support in KSZ9477 driver. This switch is similar to
KSZ9477 except the ingress tail tag has 1 byte instead of 2 bytes, so
KSZ9893 tagging will be used.
The XMII register that governs how the host port communicates with the
MAC also has different register definitions.
Signed-off-by: Tristram Ha <Tristram.Ha@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Despite what the datesheet says, the silicon implements the older way
of snapshoting the statistics. Change the op.
Reported-by: Chris.Healy@zii.aero
Tested-by: Chris.Healy@zii.aero
Fixes: 0ac64c394900 ("net: dsa: mv88e6xxx: mv88e6161 uses mv88e6320 stats snapshot")
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
drivers/net/dsa/mt7530.c:649:3-4: Unneeded semicolon
drivers/net/ethernet/cisco/enic/enic_clsf.c:35:2-3: Unneeded semicolon
drivers/net/ethernet/faraday/ftgmac100.c:1640:2-3: Unneeded semicolon
drivers/net/ethernet/mediatek/mtk_eth_soc.c:229:2-3: Unneeded semicolon
drivers/net/usb/sr9700.c:437:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Acked-by: Sean Wang <sean.wang@mediatek.com> for mt7530 and mtk_eth_soc
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When debugging another issue I faced an interrupt storm in this
driver (88E6390, port 9 in SGMII mode), consisting of alternating
link-up / link-down interrupts. Analysis showed that the driver
wanted to set a cmode that was set already. But so far
mv88e6390x_port_set_cmode() doesn't check this and powers down
SERDES, what causes the link to break, and eventually results in
the described interrupt storm.
Fix this by checking whether the cmode actually changes. We want
that the very first call to mv88e6390x_port_set_cmode() always
configures the registers, therefore initialize port.cmode with
a value that is different from any supported cmode value.
We have to take care that we only init the ports cmode once
chip->info->num_ports is set.
v2:
- add small helper and init the number of actual ports only
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Upon setting the cmode on 6390 and 6390X, the associated serdes
interfaces must be powered off/on.
Both 6390X and 6390 share code to do so, but it currently uses the 6390
specific helper mv88e6390_serdes_power() to disable and enable the
serdes interface.
This call will fail silently on 6390X when trying so set a 10G interface
such as XAUI or RXAUI, since mv88e6390_serdes_power() internally grabs
the lane number based on modes supported by the 6390, and returns 0 when
getting -ENODEV as a lane number.
Using mv88e6390x_serdes_power() should be safe here, since we explicitly
rule-out all ports but the 9 and 10, and because modes supported by 6390
ports 9 and 10 are a subset of those supported on 6390X.
This was tested on 6390X using RXAUI mode.
Fixes: 364e9d7776a3 ("net: dsa: mv88e6xxx: Power on/off SERDES on cmode change")
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
