| Age | Commit message (Collapse) | Author |
|---|
|
Flip the IVL_SVL_SELECT bit correctly based on the VLAN enable status,
the default is to perform Shared VLAN learning instead of Individual
learning.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When asking the ARL to read a MAC address, we will get a number of bins
returned in a single read. Out of those bins, there can essentially be 3
states:
- all bins are full, we have no space left, and we can either replace an
existing address or return that full condition
- the MAC address was found, then we need to return its bin index and
modify that one, and only that one
- the MAC address was not found and we have a least one bin free, we use
that bin index location then
The code would unfortunately fail on all counts.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The ARL {MAC,VID} tuple and the forward entry were off by 0x10 bytes,
which means that when we read/wrote from/to ARL bin index 0, we were
actually accessing the ARLA_RWCTRL register.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When support for the MDB entries was added, the valid bit was correctly
changed to be assigned depending on the remaining port bitmask, that is,
if there were no more ports added to the entry's port bitmask, the entry
now becomes invalid. There was another assignment a few lines below that
would override this which would invalidate entries even when there were
still multiple ports left in the MDB entry.
Fixes: 5d65b64a3d97 ("net: dsa: b53: Add support for MDB")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When VLAN is enabled, and an ARL search is issued, we also need to
compare the full {MAC,VID} tuple before returning a successful search
result.
Fixes: 1da6df85c6fb ("net: dsa: b53: Implement ARL add/del/dump operations")
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 7278, port 7 connects to the ASP which should only receive frames
through the use of CFP rules, it is not desirable to have it be part of
a bridge at all since that would make it pick up unwanted traffic that
it may not even be able to filter or sustain.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
On 7278, port 7 of the switch connects to the ASP UniMAC which is not
capable of processing VLAN tagged frames. We can still allow the port to
be part of a VLAN entry, and we may want it to be untagged on egress on
that VLAN because of that limitation.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The first time b53_configure_vlan() is called we have not configured any
VLAN entries yet, since that happens later when interfaces get brought
up. When b53_configure_vlan() is called again from suspend/resume we
need to restore all VLAN entries though.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It looks like the Broadcom switches supported by the b53 driver don't
support precise configuration of the MTU, but just a mumbo-jumbo boolean
flag. Set that.
Also configure BCM583XX devices to send and receive jumbo frames when
ports are configured with 10/100 Mbps speed.
Signed-off-by: Murali Krishna Policharla <murali.policharla@broadcom.com>
Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Propagate the resolved link configuration down via DSA's
phylink_mac_link_up() operation to allow split PCS/MAC to work.
Tested-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We need to ensure that the default VID is untagged otherwise the switch
will be sending tagged frames and the results can be problematic. This
is especially true with b53 switches that use VID 0 as their default
VLAN since VID 0 has a special meaning.
Fixes: fea83353177a ("net: dsa: b53: Fix default VLAN ID")
Fixes: 061f6a505ac3 ("net: dsa: Add ndo_vlan_rx_{add, kill}_vid implementation")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
b53_configure_vlan() is called by the bcm_sf2 driver upon setup and
indirectly through resume as well. During the initial setup, we are
guaranteed that dev->vlan_enabled is false, so there is no change in
behavior, however during suspend, we may have enabled VLANs before, so we
do want to restore that setting.
Fixes: dad8d7c6452b ("net: dsa: b53: Properly account for VLAN filtering")
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The BCM531x5 and BCM539x families require that the IMP port be enabled
within the management page and that management mode (SM_SW_FWD_MODE) be
turned on. Once this is done, everything works as expected, including
multicast with standalone DSA devices or bridge devices.
Because such switches are frequencly cascaded with other internal
Broadcom switches on which we want to enable Broadcom tags, update
b53_can_enable_brcm_tags() to check the kind of DSA master tagging
protocol being used, if it is one of the two supported Broadcom tagging
protocols, force DSA_TAG_PROTO_NONE.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
It is possible to stack multiple DSA switches in a way that they are not
part of the tree (disjoint) but the DSA master of a switch is a DSA
slave of another. When that happens switch drivers may have to know this
is the case so as to determine whether their tagging protocol has a
remove chance of working.
This is useful for specific switch drivers such as b53 where devices
have been known to be stacked in the wild without the Broadcom tag
protocol supporting that feature. This allows b53 to continue supporting
those devices by forcing the disabling of Broadcom tags on the outermost
switches if necessary.
The get_tag_protocol() function is therefore updated to gain an
additional enum dsa_tag_protocol argument which denotes the current
tagging protocol used by the DSA master we are attached to, else
DSA_TAG_PROTO_NONE for the top of the dsa_switch_tree.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
There were several issues with 53568438e381 ("net: dsa: b53: Add support for port_egress_floods callback") that resulted in breaking connectivity for standalone ports:
- both user and CPU ports must allow unicast and multicast forwarding by
default otherwise this just flat out breaks connectivity for
standalone DSA ports
- IP multicast is treated similarly as multicast, but has separate
control registers
- the UC, MC and IPMC lookup failure register offsets were wrong, and
instead used bit values that are meaningful for the
B53_IP_MULTICAST_CTRL register
Fixes: 53568438e381 ("net: dsa: b53: Add support for port_egress_floods callback")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In preparation for supporting IGMP snooping with or without the use of
a bridge, add support within b53_common.c to program the ARL entries for
multicast operations. The key difference is that a multicast ARL entry
is comprised of a bitmask of enabled ports, instead of a port number.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Now that ports are dynamically listed in the fabric, there is no need
to provide a special helper to allocate the dsa_switch structure. This
will give more flexibility to drivers to embed this structure as they
wish in their private structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Do not let the drivers access the ds->ports static array directly
while there is a dsa_to_port helper for this purpose.
At the same time, un-const this helper since the SJA1105 driver
assigns the priv member of the returned dsa_port structure.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Clearing the existing bitmask of mirrored ports essentially prevents us
from capturing more than one port at any given time. This is clearly
wrong, do not clear the bitmask prior to setting up the new port.
Reported-by: Hubert Feurstein <h.feurstein@gmail.com>
Fixes: ed3af5fd08eb ("net: dsa: b53: Add support for port mirroring")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
This patch corrects the SPDX License Identifier style
in header file for Broadcom BCM53xx managed switch driver.
For C header files Documentation/process/license-rules.rst
mandates C-like comments (opposed to C source files where
C++ style should be used)
Changes made by using a script provided by Joe Perches here:
https://lkml.org/lkml/2019/2/7/46.
Suggested-by: Joe Perches <joe@perches.com>
Signed-off-by: Nishad Kamdar <nishadkamdar@gmail.com>
Reviewed-by: Vivien Didelot <vivien.didelot@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Jakub Kicinski <jakub.kicinski@netronome.com>
|
|
Add support for configuring the per-port egress flooding control for
both Unicast and Multicast traffic.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The .port_enable and .port_disable operations are currently only
called for user ports, hence assuming they have a slave device. In
preparation for using these operations for other port types as well,
simply guard all implementations against non user ports and return
directly in such case.
Note that bcm_sf2_sw_suspend() currently calls bcm_sf2_port_disable()
(and thus b53_disable_port()) against the user and CPU ports, so do
not guards those functions. They will be called for unused ports in
the future, but that was expected by those drivers anyway.
Signed-off-by: Vivien Didelot <vivien.didelot@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Use devm_platform_ioremap_resource() to simplify the code a bit.
This is detected by coccinelle.
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
A b53 device may configured through an external EEPROM like the switch
device on the Lamobo R1 router board. The configuration of a port may
therefore differ from the reset configuration of the switch.
The switch configuration reported by the DSA subsystem is different until
the port is configured by DSA i.e. a port can be active, while the DSA
subsystem reports the port is inactive. Disable all ports and not only
the unused ones to put all ports into a well defined state.
Signed-off-by: Benedikt Spranger <b.spranger@linutronix.de>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
While possible (and safe) to use the newly introduced
dsa_port_is_vlan_filtering helper, fabricating a dsa_port pointer is a
bit awkward, so simply retrieve this from the dsa_switch structure.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Since DSA has recently learned to treat better with drivers that set
vlan_filtering_is_global, doing this is no longer required.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The DSA core is now able to do this check prior to calling the
.port_vlan_filtering callback, so tell it that VLAN filtering is global
for this particular hardware.
Signed-off-by: Vladimir Oltean <olteanv@gmail.com>
Suggested-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
No current DSA driver makes use of the phydev parameter passed to the
disable_port call. Remove it.
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The CPU port is special and does not need to obey VLAN restrictions as
far as untagged traffic goes, also, having the CPU port be part of a
particular PVID is against the idea of keeping it tagged in all VLANs.
Fixes: ca8931948344 ("net: dsa: b53: Keep CPU port as tagged in all VLANs")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
VLAN filtering can be built into the kernel, and also dynamically turned
on/off through the bridge master device. Allow re-configuring the switch
appropriately to account for that by deciding whether VLAN table
(v_table) misses should lead to a drop or forward.
Fixes: a2482d2ce349 ("net: dsa: b53: Plug in VLAN support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
We were not consistent in how the default VID of a given port was
defined, b53_br_leave() would make sure the VLAN ID would be either 0/1
depending on the switch generation, but b53_configure_vlan(), which is
the default configuration would unconditionally set it to 1. The correct
value is 1 for 5325/5365 series and 0 otherwise. To avoid repeating that
mistake ever again, introduce a helper function: b53_default_pvid() to
factor that out.
Fixes: 967dd82ffc52 ("net: dsa: b53: Add support for Broadcom RoboSwitch")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Fixes the issues with non BCM58XX chips in the b53 driver
failing, when the irq is not specified in the device tree.
Removed the check for BCM58XX in b53_srab_prepare_irq(),
so the 'port->irq' will be set to '-EXIO' if the irq is not
specified in the device tree.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts")
Fixes: b2ddc48a81b5 ("net: dsa: b53: Do not fail when IRQ are not initialized")
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
|
|
Commit c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port
incorrectly") was a bit too trigger happy in removing the CPU port from
the VLAN membership because we rely on DSA to program the CPU port VLAN,
which it does, except it does not bother itself with tagged/untagged and
just usese untagged.
Having the CPU port "follow" the user ports tagged/untagged is not great
and does not allow for properly differentiating, so keep the CPU port
tagged in all VLANs.
Reported-by: Gerhard Wiesinger <lists@wiesinger.com>
Fixes: c499696e7901 ("net: dsa: b53: Stop using dev->cpu_port incorrectly")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When B53_SERDES is a loadable module, a built-in srab driver still
cannot reach it, so the previous fix is incomplete:
b53_srab.c:(.text+0x3f4): undefined reference to `b53_serdes_init'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe64): undefined reference to `b53_serdes_link_state'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe74): undefined reference to `b53_serdes_link_set'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xe88): undefined reference to `b53_serdes_an_restart'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea0): undefined reference to `b53_serdes_phylink_validate'
drivers/net/dsa/b53/b53_srab.o:(.rodata+0xea4): undefined reference to `b53_serdes_config'
Add a Kconfig dependency that forces srab to also be a module
in this case, but allow it to be built-in when serdes is
disabled or built-in.
Fixes: 7a8c7f5c30f9 ("net: dsa: b53: Fix build with B53_SRAB enabled and not B53_SERDES")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In both 802.3z and SGMII modes we need to configure the MAC accordingly
to flip between Fiber and SGMII modes, and we need to read the MAC
status from the SGMII in-band control word.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Maths went wrong, to get 0x20, we need to do 0x1e + (x) * 2, not 0x18,
fix that offset so we access the correct registers. This would make us
not access the correct SerDes Digital control words, status would be
fine and so we would not be correctly flipping between Fiber and SGMII
modes resulting in incorrect status words being pulled into the SerDes
digital status register.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
PHYLINK takes care of filing the right information into
state->an_enabled, get rid of the read from the SerDes's BMCR register.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
When the Device Tree is not providing the per-port interrupts, do not fail
during b53_srab_irq_enable() but instead bail out gracefully. The SRAB driver
is used on the BCM5301X (Northstar) platforms which do not yet have the SRAB
interrupts wired up.
Fixes: 16994374a6fc ("net: dsa: b53: Make SRAB driver manage port interrupts")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Built-in PHY ports are still being polled, avoid generating spurious
and duplicate events which the PHY library resolves through polling
anyways.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support")
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The "pause" variable is only initialized on BCM5301x.
Fixes: 5e004460f874 ("net: dsa: b53: Add helper to set link parameters")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
In case B53_SRAB is enabled, but not B53_SERDES, we can get the
following linking error:
ERROR: "b53_serdes_init" [drivers/net/dsa/b53/b53_srab.ko] undefined!
We also need to ifdef the body of b53_srab_serdes_map_lane() since it
would not be used when B53_SERDES is disabled and that would produce a
warning.
Fixes: 0e01491de646 ("net: dsa: b53: Add SerDes support")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Northstar Plus SerDes which is accessed through a
special page of the switch. Since this is something that most people
probably will not want to use, make it a configurable option with a
default on ARCH_BCM_NSP where it is the most useful currently.
The SerDes supports both SGMII and 1000baseX modes for both lanes, and
2500baseX for one of the lanes, and is internally looking like a
seemingly standard MII PHY, except for the few bits that got repurposed.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for PHYLINK, things are reasonably straight forward since we
do not yet support SerDes interfaces, that leaves us with just
MLO_AN_PHY and MLO_AN_FIXED to deal with.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Extract the logic from b53_adjust_link() responsible for overriding a
given port's link, speed, duplex and pause settings and make two helper
functions to set the port's configuration and the port's link settings.
We will make use of both, as separate functions while adding PHYLINK
support next.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Update the SRAB driver to manage per-port interrupts. Since we cannot
sleep during b53_io_ops, schedule a workqueue whenever we get a port
specific interrupt. We will later make use of this to call back into
PHYLINK when there is e.g: a link state change.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Some switches expose individual interrupt line(s) for port specific
event(s), allow configuring these interrupts at an appropriate time
during port_enable/disable callbacks where all port specific resources
are known to be set-up and ready for use.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
The SRAB driver is the default way to communicate with the integrated
switch on iProc platforms and the MMAP driver is the way to communicate
with the integrated switch on DSL BCM63xx and CM BCM33xx.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
Add support for the Broadcom Omega SoC internal ethernet switch
to the b53 srab driver in the DSA framework.
Signed-off-by: Arun Parameswaran <arun.parameswaran@broadcom.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
