summaryrefslogtreecommitdiff
path: root/drivers/mtd
AgeCommit message (Collapse)Author
2015-01-07mtd: bcm47xxpart: support SquashFS with an original magicRafał Miłecki
SquashFS is supposed to use magic defined as SQUASHFS_MAGIC. What we were supporting so far (SQSH_MAGIC) is something ZTE specific. This patch adds support for Xiaomi R1D. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-01-07mtd: bcm47xxpart: lower minimal blocksize to 4Ki (from 64Ki)Rafał Miłecki
Some devices like Netgear WNR1000v3 or WGR614v10 have partitions aligned to 0x1000. Using bigger blocksize stopped us from detecting some parts. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-01-07mtd: bcm47xxpart: support TRX data partition being UBIRafał Miłecki
Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2015-01-07mtd: spi-nor: Add quad I/O support for Micron SPI NORBean Huo 霍斌斌 (beanhuo)
This patch adds code which enables Quad I/O mode on Micron SPI NOR flashes. For Micron SPI NOR flash, enabling or disabling quad I/O protocol can be done By two methods, which are to use EVCR (Enhanced Volatile Configuration Register) and the ENTER QUAD I/O MODE command. There is no difference between these two methods. Unfortunately, for some Micron SPI NOR flashes, there no ENTER Quad I/O command (35h), such as n25q064. But for all current Micron SPI NOR, if it support quad I/O mode, using EVCR definitely be supported. It is a recommended method to enable Quad I/O mode by EVCR, Quad I/O protocol bit 7. When EVCR bit 7 is reset to 0, the SPI NOR flash will operate in quad I/O mode. This patch has been tested on N25Q512A and MT25TL256BAA1ESF. Micron SPI NOR of spi_nor_ids[] table all support this method. Signed-off-by: Bean Huo <beanhuo@micron.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-22mtd: nand: gpmi: remove deprecated commentBoris BREZILLON
Now that we have raw functions properly implemented we can remove this FIXME. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Huang Shijie <shijie.huang@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-22mtd: gpmi: Remove noisy error messageFabio Estevam
mx28evk board has a socket for NAND flash that comes with no NAND flash populated, and then we get this message on every boot: [ 1.657603] gpmi-nand 8000c000.gpmi-nand: driver registration failed: -19 which is not very helpful, so get rid of this error message. Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-17Merge tag 'for-linus-20141215' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD updates from Brian Norris: "Summary: - Add device tree support for DoC3 - SPI NOR: Refactoring, for better layering between spi-nor.c and its driver users (e.g., m25p80.c) New flash device support Support 6-byte ID strings - NAND: New NAND driver for Allwinner SoC's (sunxi) GPMI NAND: add support for raw (no ECC) access, for testing purposes Add ATO manufacturer ID A few odd driver fixes - MTD tests: Allow testers to compensate for OOB bitflips in oobtest Fix a torturetest regression - nandsim: Support longer ID byte strings And more" * tag 'for-linus-20141215' of git://git.infradead.org/linux-mtd: (63 commits) mtd: tests: abort torturetest on erase errors mtd: physmap_of: fix potential NULL dereference mtd: spi-nor: allow NULL as chip name and try to auto detect it mtd: nand: gpmi: add raw oob access functions mtd: nand: gpmi: add proper raw access support mtd: nand: gpmi: add gpmi_copy_bits function mtd: spi-nor: factor out write_enable() for erase commands mtd: spi-nor: add support for s25fl128s mtd: spi-nor: remove the jedec_id/ext_id mtd: spi-nor: add id/id_len for flash_info{} mtd: nand: correct the comment of function nand_block_isreserved() jffs2: Drop bogus if in comment mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpy mtd: cafe_nand: drop duplicate .write_page implementation mtd: m25p80: Add support for serial flash Spansion S25FL132K MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_ids mtd: spi-nor: improve wait-till-ready timeout loop mtd: delete unnecessary checks before two function calls mtd: nand: omap: Fix NAND enumeration on 3430 LDP mtd: nand: add ATO manufacturer info ...
2014-12-14Merge tag 'driver-core-3.19-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core Pull driver core update from Greg KH: "Here's the set of driver core patches for 3.19-rc1. They are dominated by the removal of the .owner field in platform drivers. They touch a lot of files, but they are "simple" changes, just removing a line in a structure. Other than that, a few minor driver core and debugfs changes. There are some ath9k patches coming in through this tree that have been acked by the wireless maintainers as they relied on the debugfs changes. Everything has been in linux-next for a while" * tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits) Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries" fs: debugfs: add forward declaration for struct device type firmware class: Deletion of an unnecessary check before the function call "vunmap" firmware loader: fix hung task warning dump devcoredump: provide a one-way disable function device: Add dev_<level>_once variants ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries ath: use seq_file api for ath9k debugfs files debugfs: add helper function to create device related seq_file drivers/base: cacheinfo: remove noisy error boot message Revert "core: platform: add warning if driver has no owner" drivers: base: support cpu cache information interface to userspace via sysfs drivers: base: add cpu_device_create to support per-cpu devices topology: replace custom attribute macros with standard DEVICE_ATTR* cpumask: factor out show_cpumap into separate helper function driver core: Fix unbalanced device reference in drivers_probe driver core: fix race with userland in device_add() sysfs/kernfs: make read requests on pre-alloc files use the buffer. sysfs/kernfs: allow attributes to request write buffer be pre-allocated. fs: sysfs: return EGBIG on write if offset is larger than file size ...
2014-12-12mtd: tests: abort torturetest on erase errorsBrian Norris
The torture test should quit once it actually induces an error in the flash. This step was accidentally removed during refactoring. Without this fix, the torturetest just continues infinitely, or until the maximum cycle count is reached. e.g.: ... [ 7619.218171] mtd_test: error -5 while erasing EB 100 [ 7619.297981] mtd_test: error -5 while erasing EB 100 [ 7619.377953] mtd_test: error -5 while erasing EB 100 [ 7619.457998] mtd_test: error -5 while erasing EB 100 [ 7619.537990] mtd_test: error -5 while erasing EB 100 ... Fixes: 6cf78358c94f ("mtd: mtd_torturetest: use mtd_test helpers") Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Akinobu Mita <akinobu.mita@gmail.com> Cc: <stable@vger.kernel.org>
2014-12-12mtd: physmap_of: fix potential NULL dereferenceArd Biesheuvel
On device remove, when testing the cmtd field of an of_flash struct to decide whether it is a concatenated device or not, we get a false positive on cmtd == NULL, and dereference it subsequently. This may occur if of_flash_remove() is called from the cleanup path of of_flash_probe(). Instead, test for NULL first, and only then perform the test for a concatenated device. Signed-off-by: Ard Biesheuvel <ard.biesheuvel@linaro.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: spi-nor: allow NULL as chip name and try to auto detect itRafał Miłecki
This will allow spi-nor users to plainly use JEDEC to detect flash chip. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: nand: gpmi: add raw oob access functionsBoris BREZILLON
Implement raw OOB access functions to retrieve OOB bytes when accessing the NAND in raw mode. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: nand: gpmi: add proper raw access supportBoris BREZILLON
Several MTD users (either in user or kernel space) expect a valid raw access support to NAND chip devices. This is particularly true for testing tools which are often touching the data stored in a NAND chip in raw mode to artificially generate errors. The GPMI drivers do not implemenent raw access functions, and thus rely on default HW_ECC scheme implementation. The default implementation consider the data and OOB area as properly separated in their respective NAND section, which is not true for the GPMI controller. In this driver/controller some OOB data are stored at the beginning of the NAND data area (these data are called metadata in the driver), then ECC bytes are interleaved with data chunk (which is similar to the HW_ECC_SYNDROME scheme), and eventually the remaining bytes are used as OOB data. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: nand: gpmi: add gpmi_copy_bits functionBoris BREZILLON
Add a new function to copy bits (not bytes) from a memory region to another one. This function is similar to memcpy except it acts at bit level. It is needed to implement GPMI raw access functions and adapt to the hardware ECC engine which does not pad ECC bits to the next byte boundary. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Tested-by: Huang Shijie <shijie8@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: spi-nor: factor out write_enable() for erase commandsBrian Norris
write_enable() was being duplicated to both m25p80.c and fsl-quadspi.c. But this should be handled within the spi-nor abstraction layer. At the same time, let's add write_disable() after erasing, so we don't leave the flash in a write-enabled state afterward. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <shijie.huang@intel.com>
2014-12-01mtd: spi-nor: add support for s25fl128sHuang Shijie
We need to store the six bytes ID for s25fl128s, since it shares the same five bytes with s25fl129p1. This patch adds a macro INFO6 which is used for the six bytes ID flash, and adds a new item for the s25fl128s. Signed-off-by: Huang Shijie <shijie.huang@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: spi-nor: remove the jedec_id/ext_idHuang Shijie
The "id" array contains all the information about the JEDEC and the manufacturer ID info. This patch removes the jedec_id/ext_id from flash_info. Signed-off-by: Huang Shijie <shijie.huang@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-12-01mtd: spi-nor: add id/id_len for flash_info{}Huang Shijie
This patch adds the id/id_len fields for flash_info{}, and rewrite the INFO to fill them. And at last, we read out 6 bytes in the spi_nor_read_id(), and we use these new fields to parse out the correct flash_info. Signed-off-by: Huang Shijie <shijie.huang@intel.com> Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-28mtd: nand: correct the comment of function nand_block_isreserved()Gu Zheng
Signed-off-by: Gu Zheng <guz.fnst@cn.fujitsu.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: atmel_nand: replace memcpy32_toio/memcpy32_fromio with memcpyWu, Josh
There is no need to use memcpy32_toio/memcpy32_fromio to transfer data between memory and NFC sram. As the NFC sram is a also a memory space not an I/O space, we can just use memcpy(). We remove the __iomem prefix for NFC sram to avoid sparse warnings. Signed-off-by: Josh Wu <josh.wu@atmel.com> Reviewed-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: cafe_nand: drop duplicate .write_page implementationBrian Norris
This write_page() function is functionally equivalent to the default in nand_base.c. Its only difference is in subpage programming support, which cafe_nand.c does not advertise, so the difference is negligible. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: m25p80: Add support for serial flash Spansion S25FL132KKnut Wohlrab
Signed-off-by: Knut Wohlrab <knut.wohlrab@de.bosch.com> Signed-off-by: Alison Chaiken <alison_chaiken@mentor.com> Reviewed-by: Jagannadha Sutradharudu Teki <jagannadh.teki@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25MTD: m25p80: fix inconsistency in m25p_ids compared to spi_nor_idsAlison Chaiken
As stated in a5b7616c5, "mtd: m25p80,spi-nor: Fix module aliases for m25p80", m25p_ids[] in m25p80.c needs to be kept in sync with spi_nor_ids[] in spi-nor.c. The change here corrects a misalignment. (We were missing m25px80 and we had a duplicate w25q128.) Signed-off-by: Alison Chaiken <alison_chaiken@mentor.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: <stable@vger.kernel.org> # 3.18+
2014-11-25mtd: spi-nor: improve wait-till-ready timeout loopBrian Norris
There are a few small issues with the timeout loop in spi_nor_wait_till_ready(): * The first operation should not be a reschedule; we should check the status register at least once to see if we're complete! * We should check the status register one last time after declaring the deadline has passed, to prevent a premature timeout error (this is theoretically possible if we sleep for a long time after the previous status register check). * Add an error message, so it's obvious if we ever hit a timeout. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Huang Shijie <shijie.huang@intel.com> Reviewed-by: Ezequiel Garcia <ezequiel@vanguardiasur.com.ar>
2014-11-25mtd: delete unnecessary checks before two function callsMarkus Elfring
The functions kfree() and pci_dev_put() test whether their argument is NULL and then return immediately. Thus the test around the call is not needed. This issue was detected by using the Coccinelle software. Signed-off-by: Markus Elfring <elfring@users.sourceforge.net> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: nand: omap: Fix NAND enumeration on 3430 LDPRoger Quadros
3430LDP has NAND flash with 32 bytes OOB size which is sufficient to hold BCH8 codes but the small page check introduced in commit b491da7233d5 ("mtd: nand: omap: clean-up ecc layout for BCH ecc schemes") considers anything below 64 bytes unsuitable for BCH4/8/16. There is another bug in that code where it doesn't skip the check for OMAP_ECC_HAM1_CODE_SW. Get rid of that small page check code as it is insufficient and redundant because we are checking for OOB available bytes vs ecc layout before calling nand_scan_tail(). Fixes: b491da7233d5 ("mtd: nand: omap: clean-up ecc layout for BCH ecc schemes") Reported-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: nand: add ATO manufacturer infoBrian Norris
Tested with ATO AFND1G08U3, 128MiB NAND. Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-25mtd: nand: print erase size on initRafał Miłecki
It may be useful info, e.g. if someone wants to use ubinize. Signed-off-by: Rafał Miłecki <zajec5@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-20mtd: oobtest: correct printf() format specifier for 'size_t'Brian Norris
Fixes warning: drivers/mtd/tests/oobtest.c: In function 'memcmpshow': drivers/mtd/tests/oobtest.c:129: warning: format '%x' expects type 'unsigned int', but argument 3 has type 'size_t' Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Roger Quadros <rogerq@ti.com> Cc: Sekhar Nori <nsekhar@ti.com>
2014-11-19mtd: mtd_oobtest: add bitflip_limit parameterRoger Quadros
It is common for NAND devices to have bitflip errors. Add a bitflip_limit parameter to specify how many bitflips per page we can tolerate without flagging an error. By default zero bitflips are tolerated. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-19mtd: mtd_oobtest: Show the verification error location and dataRoger Quadros
Add a function memcmpshow() that compares the 2 data buffers and shows the address:offset and data bytes on comparison failure. This function does not break at a comparison failure but runs the check for the whole data buffer. Use memcmpshow() instead of memcmp() for all the verification paths. Signed-off-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Sekhar Nori <nsekhar@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-07UBI: Fix invalid vfree()Richard Weinberger
The logic of vfree()'ing vol->upd_buf is tied to vol->updating. In ubi_start_update() vol->updating is set long before vmalloc()'ing vol->upd_buf. If we encounter a write failure in ubi_start_update() before vmalloc() the UBI device release function will try to vfree() vol->upd_buf because vol->updating is set. Fix this by allocating vol->upd_buf directly after setting vol->updating. Fixes: [ 31.559338] UBI warning: vol_cdev_release: update of volume 2 not finished, volume is damaged [ 31.559340] ------------[ cut here ]------------ [ 31.559343] WARNING: CPU: 1 PID: 2747 at mm/vmalloc.c:1446 __vunmap+0xe3/0x110() [ 31.559344] Trying to vfree() nonexistent vm area (ffffc90001f2b000) [ 31.559345] Modules linked in: [ 31.565620] 0000000000000bba ffff88002a0cbdb0 ffffffff818f0497 ffff88003b9ba148 [ 31.566347] ffff88002a0cbde0 ffffffff8156f515 ffff88003b9ba148 0000000000000bba [ 31.567073] 0000000000000000 0000000000000000 ffff88002a0cbe88 ffffffff8156c10a [ 31.567793] Call Trace: [ 31.568034] [<ffffffff818f0497>] dump_stack+0x4e/0x7a [ 31.568510] [<ffffffff8156f515>] ubi_io_write_vid_hdr+0x155/0x160 [ 31.569084] [<ffffffff8156c10a>] ubi_eba_write_leb+0x23a/0x870 [ 31.569628] [<ffffffff81569b36>] vol_cdev_write+0x226/0x380 [ 31.570155] [<ffffffff81179265>] vfs_write+0xb5/0x1f0 [ 31.570627] [<ffffffff81179f8a>] SyS_pwrite64+0x6a/0xa0 [ 31.571123] [<ffffffff818fde12>] system_call_fastpath+0x16/0x1b Cc: <stable@vger.kernel.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2014-11-07UBI: Fix double free after do_sync_erase()Richard Weinberger
If the erase worker is unable to erase a PEB it will free the ubi_wl_entry itself. The failing ubi_wl_entry must not free()'d again after do_sync_erase() returns. Cc: <stable@vger.kernel.org> Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2014-11-07UBI: vtbl: Use ubi_eba_atomic_leb_change()Richard Weinberger
This is more a cosmetic change than a fix. By using ubi_eba_atomic_leb_change() we can guarantee that the first VTBL record is always correct and we don't really need the second one anymore. But we have to keep the second one to not break anything. Artem: add a comment Signed-off-by: Richard Weinberger <richard@nod.at> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2014-11-07UBI: Extend UBI layer debug/messaging capabilitiesTanya Brokhman
If there is more then one UBI device mounted, there is no way to distinguish between messages from different UBI devices. Add device number to all ubi layer message types. The R/O block driver messages were replaced by pr_* since ubi_device structure is not used by it. Amended a bit by Artem. Signed-off-by: Tanya Brokhman <tlinder@codeaurora.org> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com>
2014-11-05fsl_ifc: Support all 8 IFC chip selectsAaron Sierra
Freescale's QorIQ T Series processors support 8 IFC chip selects within a memory map backward compatible with previous P Series processors which supported only 4 chip selects. Signed-off-by: Aaron Sierra <asierra@xes-inc.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: atmel_nand: make PMECC lookup table and offset property optionalJosh Wu
If there is no PMECC lookup table stored in ROM, or lookup table offset is not specified, PMECC driver should build it in DDR by itself. That make the PMECC driver work for some board which doesn't have PMECC lookup table in ROM. The PMECC use the BCH algorithm, so based on the build_gf_tables() function in lib/bch.c, we can build the Galois Field lookup table. For more information can refer to section 5.4 of PMECC controller application note: http://www.atmel.com/images/doc11127.pdf Signed-off-by: Josh Wu <josh.wu@atmel.com> Cc: devicetree@vger.kernel.org Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: mxc_nand: use __iowrite32_copy for 32 bit copyKoul, Vinod
The driver was also using own method to do 32bit copy, turns out we have a kernel API so use that instead Signed-off-by: Vinod Koul <vinod.koul@intel.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: intflmount: fix off by one error in INFTL_dumpVUchains()Dan Carpenter
The ->PUtable[] array has "->nb_blocks" number of elemetns so this comparison should be ">=" instead of ">". Otherwise it could result in a minor read beyond the end of an array. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: spi-nor: Add support for SST spi flashHarini Katakam
Add sst25wf080 to the spi-nor device id table. Signed-off-by: Harini Katakam <harinik@xilinx.com> Reviewed-by: Peter Crosthwaite <peter.crosthwaite@xilinx.com> Signed-off-by: Michal Simek <michal.simek@xilinx.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: spi-nor: Add support for Fujitsu MB85RS1MT FRAMRostislav Lisovy
Tested with this particular FRAM chip Signed-off-by: Rostislav Lisovy <lisovy@merica.cz> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: nand: omap: Synchronize the access to the ECC engineRostislav Lisovy
The AM335x Technical Reference Manual (spruh73j.pdf) says "Because the ECC engine includes only one accumulation context, it can be allocated to only one chip-select at a time ... " (7.1.3.3.12.3). Since the commit 97a288ba2cfa ("ARM: omap2+: gpmc-nand: Use dynamic platform_device_alloc()") gpmc-nand driver supports multiple NAND flash devices connected to the single controller. Use global 'struct nand_hw_control' among multiple NAND instances to synchronize the access to the single ECC Engine. Tested with custom AM335x board using 2x NAND flash chips. Signed-off-by: Rostislav Lisovy <lisovy@merica.cz> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: spi-nor: Move n25q032 entry to Micron devices listChunhe Lan
Because n25q032 is the Micron SPI chip, move it to Micron devices list group. In order that know which Micron SPI chips have been support at a glance. Signed-off-by: Chunhe Lan <Chunhe.Lan@freescale.com> Cc: Brian Norris <computersforpeace@gmail.com> Cc: Marek Vasut <marex@denx.de> Cc: Huang Shijie <shijie8@gmail.com> Acked-by: Marek Vasut <marex@denx.de> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: dataflash: Remove use of tx_dmaMark Brown
We are trying to remove the legacy tx_dma and rx_dma fields from the spi_transfer structure. Currently dataflash uses tx_dma but only to make sure that it's set to 0 so we can remove this use by replacing with a zero initialisation of the entire spi_transfer struct. Signed-off-by: Mark Brown <broonie@kernel.org> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2014-11-05mtd: spi-nor: drop replaceable wait-till-ready function pointerBrian Norris
We don't need to expose a 'wait-till-ready' interface to drivers. Status register polling should be handled by the core spi-nor.c library, and as of now, I see no need to provide a special driver-specific hook for it. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-11-05mtd: fsl-quadspi: drop wait-till-ready checksBrian Norris
spi-nor.c should be taking care of these now. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Cc: Huang Shijie <b32955@freescale.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-11-05mtd: m25p80: drop wait-till-ready checksBrian Norris
spi-nor.c should be taking care of these now. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-11-05mtd: spi-nor: move "wait-till-ready" checks into erase/write functionsBrian Norris
We shouldn't have *every* function checking if a previous write is complete; this should be done synchronously after each write/erase. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de>
2014-11-05mtd: spi-nor: handle timeout errors in spi_nor_write()Brian Norris
The error label was unused here. It looks like we're missing at least one case that should be doing 'goto write_err'. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Acked-by: Huang Shijie <shijie8@gmail.com>
2014-11-05mtd: spi-nor: eliminate duplicate spi_nor_wait_till_{, fsr}_ready() codeBrian Norris
These functions were near-carbon-copies due to a small per-flash quirk. Let's add a new spi_nor::flags bitfield to support these types of quirks. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Reviewed-by: Marek Vasut <marex@denx.de> Cc: Graham Moore <grmoore@altera.com> Cc: Huang Shijie <shijie8@gmail.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-22 12:22:58 +0000