| Age | Commit message (Collapse) | Author |
|---|
|
- Don't use `tmp` for two purposes (return value, loop counter).
Instead, use `i` for the loop counter, and `ret` for the return value.
- Don't use tabs between type and name in variable declarations,
for consistency with other functions in spi-nor.c.
- Rewrite nested `if`s as `if (a && b)`.
- Remove `info` variable, and use spi_nor_ids[i] directly.
Signed-off-by: Jonathan Neuschäfer <j.neuschaefer@gmx.net>
[tudor.ambarus@microchip.com: change i's type from int to unsigned int,
reorder local variables]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Make use of the spi-mem direct mapping API to let advanced controllers
optimize read/write operations when they support direct mapping.
Based on the original patch by Boris Brezillon
<boris.brezillon@bootlin.com>.
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Reviewed-by: Boris Brezillon <boris.brezillon@collabora.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
spi_nor_spimem_xfer_data() being a helper function for the data reads/
writes contains 3 fragments that depend on the data direction; and I'm
going to add another one to call the SPI dirmap API...
I think this function should be split so that the common fragments are
put into 2 functions, spi_nor_spimem_bounce() and spi_nor_spimem_exec_op()
called from spi_nor_spimem_{read|write}_data(), and the data direction
dependent bits moved back into those read/write functions -- that way we
would be able to avoid *goto*s otherwise needed in the next patch adding
the SPI dirmap support...
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The shift variable of SR_BP is conclusive because the first bit of SR_BP
is fixed on all known flashes. Replace ffs operation with SR_BP_SHIFT.
Signed-off-by: Jungseung Lee <js07.lee@samsung.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The driver calls le32_to_cpu() to convert the little-endian tables
to a CPU endianness, where le32_to_cpus() should have been called.
Was going to use that one... and then discovered a whole array
converter, le32_to_cpu_array()! :-)
Signed-off-by: Sergei Shtylyov <sergei.shtylyov@cogentembedded.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
'PTR_ERR(p) == -E*' is a stronger condition than IS_ERR(p).
Hence, IS_ERR(p) is unneeded.
The semantic patch that generates this commit is as follows:
// <smpl>
@@
expression ptr;
constant error_code;
@@
-IS_ERR(ptr) && (PTR_ERR(ptr) == - error_code)
+PTR_ERR(ptr) == - error_code
// </smpl>
Link: http://lkml.kernel.org/r/20200106045833.1725-1-masahiroy@kernel.org
Signed-off-by: Masahiro Yamada <masahiroy@kernel.org>
Cc: Julia Lawall <julia.lawall@lip6.fr>
Acked-by: Stephen Boyd <sboyd@kernel.org> [drivers/clk/clk.c]
Acked-by: Bartosz Golaszewski <bgolaszewski@baylibre.com> [GPIO]
Acked-by: Wolfram Sang <wsa@the-dreams.de> [drivers/i2c]
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com> [acpi/scan.c]
Acked-by: Rob Herring <robh@kernel.org>
Cc: Eric Biggers <ebiggers@kernel.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux
Pull MTD updates from Miquel Raynal:
"MTD core
- block2mtd: page index should use pgoff_t
- maps: physmap: minimal Runtime PM support
- maps: pcmciamtd: avoid possible sleep-in-atomic-context bugs
- concat: Fix a comment referring to an unknown symbol
Raw NAND:
- Macronix: Use match_string() helper
- Atmel: switch to using devm_fwnode_gpiod_get()
- Denali: rework the SKIP_BYTES feature and add reset controlling
- Brcmnand: set appropriate DMA mask
- Cadence: add unspecified HAS_IOMEM dependency
- Various cleanup.
Onenand:
- Rename Samsung and Omap2 drivers to avoid possible build warnings
- Enable compile testing
- Various build issues
- Kconfig cleanup
SPI-NAND:
- Support for Toshiba TC58CVG2S0HRAIJ
SPI-NOR:
- Add support for TB selection using SR bit 6,
- Add support for few flashes"
* tag 'mtd/for-5.6' of git://git.kernel.org/pub/scm/linux/kernel/git/mtd/linux: (41 commits)
mtd: concat: Fix a comment referring to an unknown symbol
mtd: rawnand: add unspecified HAS_IOMEM dependency
mtd: block2mtd: page index should use pgoff_t
mtd: maps: physmap: Add minimal Runtime PM support
mtd: maps: pcmciamtd: fix possible sleep-in-atomic-context bugs in pcmciamtd_set_vpp()
mtd: onenand: Rename omap2 driver to avoid a build warning
mtd: onenand: Use a better name for samsung driver
mtd: rawnand: atmel: switch to using devm_fwnode_gpiod_get()
mtd: spinand: add support for Toshiba TC58CVG2S0HRAIJ
mtd: rawnand: macronix: Use match_string() helper to simplify the code
mtd: sharpslpart: Fix unsigned comparison to zero
mtd: onenand: Enable compile testing of OMAP and Samsung drivers
mtd: onenand: samsung: Fix printing format for size_t on 64-bit
mtd: onenand: samsung: Fix pointer cast -Wpointer-to-int-cast warnings on 64 bit
mtd: rawnand: denali: remove hard-coded DENALI_DEFAULT_OOB_SKIP_BYTES
mtd: rawnand: denali_dt: add reset controlling
dt-bindings: mtd: denali_dt: document reset property
mtd: rawnand: denali_dt: Add support for configuring SPARE_AREA_SKIP_BYTES
mtd: rawnand: denali_dt: error out if platform has no associated data
mtd: rawnand: brcmnand: Set appropriate DMA mask
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs
Pull UBI/UBIFS updates from Miquel Raynal:
"This pull request contains mostly fixes for UBI and UBIFS:
UBI:
- Fixes for memory leaks in error paths
- Fix for an logic error in a fastmap selfcheck
UBIFS:
- Fix for FS_IOC_SETFLAGS related to fscrypt flag
- Support for FS_ENCRYPT_FL
- Fix for a dead lock in bulk-read mode"
Sent on behalf of Richard Weinberger who is traveling.
* tag 'upstream-5.6-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rw/ubifs:
ubi: Fix an error pointer dereference in error handling code
ubifs: Fix memory leak from c->sup_node
ubifs: Fix ino_t format warnings in orphan_delete()
ubifs: Fix deadlock in concurrent bulk-read and writepage
ubifs: Fix wrong memory allocation
ubi: Free the normal volumes in error paths of ubi_attach_mtd_dev()
ubi: Check the presence of volume before call ubi_fastmap_destroy_checkmap()
ubifs: Add support for FS_ENCRYPT_FL
ubifs: Fix FS_IOC_SETFLAGS unexpectedly clearing encrypt flag
ubi: wl: Remove set but not used variable 'prev_e'
ubi: fastmap: Fix inverted logic in seen selfcheck
|
|
Pull ioremap updates from Christoph Hellwig:
"Remove the ioremap_nocache API (plus wrappers) that are always
identical to ioremap"
* tag 'ioremap-5.6' of git://git.infradead.org/users/hch/ioremap:
remove ioremap_nocache and devm_ioremap_nocache
MIPS: define ioremap_nocache to ioremap
|
|
Raw NAND
* Macronix: Use match_string() helper
* Atmel: switch to using devm_fwnode_gpiod_get()
* Denali: rework the SKIP_BYTES feature and add reset controlling
* Brcmnand: set appropriate DMA mask
* Various cleanup.
Onenand drivers
* Rename Samsung and Omap2 drivers to avoid possible build warnings
* Enable compile testing
* Various build issues
* Kconfig cleanup
SPI-NAND
* Support for Toshiba TC58CVG2S0HRAIJ
|
|
SPI NOR core changes:
- Add support for TB selection using SR bit 6,
- Add support for few flashes.
|
|
Fix the comment describing what the mtd_concat_destroy() function
does. It referrers to the concat_mtd_devs symbol which has never
existed (at least not since the beginning of the Git era).
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Currently CONFIG_MTD_NAND_CADENCE implicitly depends on
CONFIG_HAS_IOMEM=y; consequently, on architectures without IOMEM we get
the following build error:
ld: drivers/mtd/nand/raw/cadence-nand-controller.o: in function `cadence_nand_dt_probe.cold.31':
drivers/mtd/nand/raw/cadence-nand-controller.c:2969: undefined reference to `devm_platform_ioremap_resource'
ld: drivers/mtd/nand/raw/cadence-nand-controller.c:2977: undefined reference to `devm_ioremap_resource'
Fix the build error by adding the unspecified dependency.
Reported-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Brendan Higgins <brendanhiggins@google.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Page index use pgoff_t to prevent risk of truncation.
Signed-off-by: Liu Song <liu.song11@zte.com.cn>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Add minimal runtime PM support (enable on probe, disable on remove), to
ensure proper operation with a parent device that uses runtime PM.
This is needed on systems where the FLASH is connected to a bus
controller that is contained in a PM domain and/or has a gateable
functional clock. In such cases, before accessing any device connected
to the external bus, the PM domain must be powered up, and/or the
functional clock must be enabled, which is typically handled through
runtime PM by the bus controller driver.
An example of this is the Renesas APE6-EVM development board, which has
an Ethernet controller and a CFI FLASH connected to the Bus State
Controller (BSC) of an R-Mobile APE6 SoC.
As long as the Ethernet driver, which had Runtime PM support since
commit 3a611e26e958b037 ("net/smsc911x: Add minimal runtime PM
support"), keeps the BSC powered, accessing the FLASH works.
When the ethernet node in r8a73a4-ape6evm.dts is disabled, the BSC is
never powered up, and the kernel crashes when trying to access the
FLASH:
Unhandled fault: imprecise external abort (0x1406) at 0x00000000
pgd = (ptrval)
[00000000] *pgd=7fef2835
Internal error: : 1406 [#1] SMP ARM
CPU: 0 PID: 122 Comm: hd Tainted: G W 5.5.0-rc1-ape6evm-00814-g38ca966db25b9dbd-dirty #136
Hardware name: Generic R8A73A4 (Flattened Device Tree)
PC is at chip_ready+0x12c/0x380
LR is at chip_ready+0x10c/0x380
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
pcmciamtd_set_vpp()
The driver may sleep while holding a spinlock.
The function call path (from bottom to top) in Linux 4.19 is:
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 309:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vpp
drivers/pcmcia/pcmcia_resource.c, 312:
mutex_lock in pcmcia_fixup_vpp
drivers/mtd/maps/pcmciamtd.c, 312:
pcmcia_fixup_vpp in pcmciamtd_set_vpp
drivers/mtd/maps/pcmciamtd.c, 306:
_raw_spin_lock_irqsave in pcmciamtd_set_vp
mutex_lock() may sleep at runtime.
To fix these bugs, the spinlock is replaced with a mutex.
These bugs are found by a static analysis tool STCheck written by
myself.
Signed-off-by: Jia-Ju Bai <baijiaju1990@gmail.com>
Reviewed-by: Dominik Brodowski <linux@dominikbrodowski.net>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
As previously reported by Sudip Mukherjee for the Samsung driver, the
omap2 onenand driver is called omap2.c in our directory and omap2.c in
the tty/serial/ directory. If both drivers are compiled as modules, it
would produce the following warning:
warning: same module names found:
drivers/tty/serial/omap2.ko
drivers/mtd/nand/onenand/omap2.ko
Rename the onenand omap2 driver so that it fits the folder's
convention: onenand_omap2.c.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Commit 55ed51fff224 ("{tty: serial, nand: onenand}: samsung: rename to
fix build warning") has changed the samsung.c driver to be
samsung_mtd.c in order to avoid a conflict in module names with the
tty driver.
Since the *_mtd suffix is very undescriptive, rename it to
onenand_samsung.c, following the folder's convention. Same will be
applied to the omap2 onenand driver.
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
devm_fwnode_get_index_gpiod_from_child() is going away as the name is
too unwieldy, let's switch to using the new devm_fwnode_gpiod_get().
Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Toshiba recently launched new revisions of their serial SLC NAND series.
TC58CVG2S0HRAIJ is a refresh of previous series with minor improvements.
Basic parameters are same so lets add support for this new revision.
Datasheet: https://business.kioxia.com/info/docget.jsp?did=58601&prodName=TC58CVG2S0HRAIJ
Tested under kernel 5.4.7.
Signed-off-by: Robert Marko <robert.marko@sartura.hr>
Cc: Luka Perkov <luka.perkov@sartura.hr>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
match_string() returns the array index of a matching string.
Use it instead of the open-coded implementation.
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The unsigned variable log_num is being assigned a return value
from the call to sharpsl_nand_get_logical_num that can return
-EINVAL.
Detected using Coccinelle:
./drivers/mtd/parsers/sharpslpart.c:207:6-13: WARNING: Unsigned expression compared with zero: log_num > 0
Fixes: 8a4580e4d298 ("mtd: sharpslpart: Add sharpslpart partition parser")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
OMAP and Samsung OneNAND drivers can be compile tested. The OMAP
drivers still depends on mach header so limit the compile testing to
ARMv7.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Print size_t as %zu to fix -Wformat warnings when compiling on 64-bit
platform (e.g. with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s5pc110_read_bufferram’:
drivers/mtd/nand/onenand/samsung_mtd.c:661:16: warning:
format ‘%d’ expects argument of type ‘int’, but argument 3 has type ‘size_t {aka long unsigned int}’ [-Wformat=]
dev_err(dev, "Couldn't map a %d byte buffer for DMA\n", count);
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
iomem pointers should be casted to unsigned long to avoid
-Wpointer-to-int-cast warnings when compiling on 64-bit platform (e.g.
with COMPILE_TEST):
drivers/mtd/nand/onenand/samsung_mtd.c: In function ‘s3c_onenand_readw’:
drivers/mtd/nand/onenand/samsung_mtd.c:251:6: warning:
cast from pointer to integer of different size [-Wpointer-to-int-cast]
if ((unsigned int) addr < ONENAND_DATARAM && onenand->bootram_command) {
^
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
As commit 0d55c668b218 (mtd: rawnand: denali: set SPARE_AREA_SKIP_BYTES
register to 8 if unset") says, there were three solutions discussed:
[1] Add a DT property to specify the skipped bytes in OOB
[2] Associate the preferred value with compatible
[3] Hard-code the default value in the driver
At that time, [3] was chosen because I did not have enough information
about the other platforms than UniPhier.
That commit also says "The preferred value may vary by platform. If so,
please trade up to a different solution." My intention was to replace
[3] with [2], not keep both [2] and [3].
Now that we have switched to [2] for SOCFPGA's SPARE_AREA_SKIP_BYTES=2,
[3] should be removed. This should be OK because denali_pci.c just
gets back to the original behavior.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
According to the Denali NAND Flash Memory Controller User's Guide,
this IP has two reset signals.
rst_n: reset most of FFs in the controller core
reg_rst_n: reset all FFs in the register interface, and in the
initialization sequencer
This commit supports controlling those reset signals.
It is possible to control them separately from the IP point of view
although they might be often tied up together in actual SoC integration.
The IP spec says, asserting only the reg_rst_n without asserting rst_n
will cause unpredictable behavior in the controller. So, the driver
deasserts ->rst_reg and ->rst in this order.
Another thing that should be kept in mind is the automated initialization
sequence (a.k.a. 'bootstrap' process) is kicked off when reg_rst_n is
deasserted.
When the reset is deasserted, the controller issues a RESET command
to the chip select 0, and attempts to read out the chip ID, and further
more, ONFI parameters if it is an ONFI-compliant device. Then, the
controller sets up the relevant registers based on the detected
device parameters.
This process might be useful for tiny boot firmware, but is redundant
for Linux Kernel because nand_scan_ident() probes devices and sets up
parameters accordingly. Rather, this hardware feature is annoying
because it ends up with misdetection due to bugs.
So, commit 0615e7ad5d52 ("mtd: nand: denali: remove Toshiba and Hynix
specific fixup code") changed the driver to not rely on it.
However, there is no way to prevent it from running. The IP provides
the 'bootstrap_inhibit_init' port to suppress this sequence, but it is
usually out of software control, and dependent on SoC implementation.
As for the Socionext UniPhier platform, LD4 always enables it. For the
later SoCs, the bootstrap sequence runs depending on the boot mode.
I added usleep_range() to make the driver wait until the sequence
finishes. Otherwise, the driver would fail to detect the chip due
to the race between the driver and hardware-controlled sequence.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The SPARE_AREA_SKIP_BYTES register is reset when the controller reset
signal is toggled. Yet, this register must be configured to match the
content of the NAND OOB area. The current default value is always set
to 8 and is programmed into the hardware in case the hardware was not
programmed before (e.g. in a bootloader) with a different value. This
however does not work when the block is reset properly by Linux.
On Altera SoCFPGA CycloneV, ArriaV and Arria10, which are the SoCFPGA
platforms which support booting from NAND, the SPARE_AREA_SKIP_BYTES
value must be set to 2. On Socionext Uniphier, the value is 8. This
patch adds support for preconfiguring the default value and handles
the special SoCFPGA case by setting the default to 2 on all SoCFPGA
platforms, while retaining the original behavior and default value of
8 on all the other platforms.
Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Miquel Raynal <miquel.raynal@bootlin.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Vignesh Raghavendra <vigneshr@ti.com>
To: linux-mtd@lists.infradead.org
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Acked-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
denali->ecc_caps is a mandatory parameter. If it were left unset,
nand_ecc_choose_conf() would end up with NULL pointer access.
So, every compatible must be associated with proper denali_dt_data.
If of_device_get_match_data() returns NULL, let it fail immediately.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
NAND controllers >= 7.0 with FLASH_DMA support physical addresses up to
40-bit, set an appropriate DMA mask for that purpose.
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Clang warns:
../drivers/mtd/nand/onenand/onenand_base.c:1269:3: warning: misleading
indentation; statement is not part of the previous 'if'
[-Wmisleading-indentation]
while (!ret) {
^
../drivers/mtd/nand/onenand/onenand_base.c:1266:2: note: previous
statement is here
if (column + thislen > writesize)
^
1 warning generated.
This warning occurs because there is a space before the tab of the while
loop. There are spaces at the beginning of a lot of the lines in this
block, remove them so that the indentation is consistent with the Linux
kernel coding style and clang no longer warns.
Fixes: a8de85d55700 ("[MTD] OneNAND: Implement read-while-load")
Link: https://github.com/ClangBuiltLinux/linux/issues/794
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fixes coccicheck warning:
drivers/mtd/nand/raw/mpc5121_nfc.c:441:2-3: Unneeded semicolon
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: zhengbin <zhengbin13@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/nand/onenand/samsung_mtd.c: In function s3c_onenand_check_lock_status:
drivers/mtd/nand/onenand/samsung_mtd.c:731:6: warning: variable tmp set but not used [-Wunused-but-set-variable]
Signed-off-by: Chen Wandun <chenwandun@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
Adjust indentation from spaces to tab (+optional two spaces) as in
coding style with command like:
$ sed -e 's/^ /\t/' -i */Kconfig
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
If "seen_pebs = init_seen(ubi);" fails then "seen_pebs" is an error pointer
and we try to kfree() it which results in an Oops.
This patch re-arranges the error handling so now it only frees things
which have been allocated successfully.
Fixes: daef3dd1f0ae ("UBI: Fastmap: Add self check to detect absent PEBs")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Add support for the Winbond W25Q32JW-xM flashes. These have a
programmable QE bit. There is also the W25Q32JW-xQ variant which shares
the ID with the W25Q32DW and W25Q32FW parts. The W25Q32JW-xQ has the QE
bit hard strapped to 1, thus don't support the /HOLD and /WP pins.
This was tested in single, dual and quad mode on a custom board with the
NXP FlexSPI controller. Also the BP bits as well as the TB bit were
tested.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
As we reset the GPMI block at resume, the timing parameters setup by a
previous exec_op is lost. Rewriting GPMI timing registers on first exec_op
after resume fixes the problem.
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
On system resume, the gpmi clock must be enabled before accessing gpmi
block. Without this, resume causes something like
[ 661.348790] gpmi_reset_block(5cbb0f7e): module reset timeout
[ 661.348889] gpmi-nand 1806000.gpmi-nand: Error setting GPMI : -110
[ 661.348928] PM: dpm_run_callback(): platform_pm_resume+0x0/0x44 returns -110
[ 661.348961] PM: Device 1806000.gpmi-nand failed to resume: error -110
Fixes: ef347c0cfd61 ("mtd: rawnand: gpmi: Implement exec_op")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
Acked-by: Han Xu <han.xu@nxp.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The commit 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable
methods") forgot to actually set the QE bit in some cases. Thus this
breaks quad mode accesses to flashes which support readback of the
status register-2. Fix it.
Fixes: 7b678c69c0ca ("mtd: spi-nor: Merge spansion Quad Enable methods")
Signed-off-by: Michael Walle <michael@walle.cc>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
mtd->size is still unassigned when running spansion_post_sfdp_fixups()
hook, therefore use nor->params.size to determine the size of flash device.
This makes sure that 4-byte addressing opcodes are used on Spansion
flashes that are larger than 16MiB and don't have SFDP 4BAIT table
populated.
Fixes: 92094ebc385e ("mtd: spi-nor: Add spansion_post_sfdp_fixups()")
Signed-off-by: Vignesh Raghavendra <vigneshr@ti.com>
Reviewed-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
The allocated normal volumes saved in ubi->volumes are not freed
in the error paths in ubi_attach_mtd_dev() and its callees (e.g.
ubi_attach() and ubi_read_volume_table()).
These normal volumes should be freed through kill_volumes() and
vol_release(), but ubi_attach_mtd_dev() may fail before
calling uif_init(), and there will be memory leaks.
So adding a new helper ubi_free_all_volumes() to free the normal
and the internal volumes. And in order to prevent double-free
of volume, reset ubi->volumes[i] to NULL after freeing.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Else there may be oops when fastmap is enabled and init_volumes() fails.
Signed-off-by: Hou Tao <houtao1@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fixes gcc '-Wunused-but-set-variable' warning:
drivers/mtd/ubi/wl.c: In function 'find_wl_entry':
drivers/mtd/ubi/wl.c:322:27: warning:
variable 'prev_e' set but not used [-Wunused-but-set-variable]
It's not used any more now, so remove it.
Fixes: f9c34bb52997 ("ubi: Fix producing anchor PEBs")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
set_seen() sets the bit corresponding to the PEB number in the bitmap,
so when self_check_seen() wants to find PEBs that haven't been seen we
have to print the PEBs that have their bit cleared, not the ones which
have it set.
Fixes: 5d71afb00840 ("ubi: Use bitmaps in Fastmap self-check code")
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The ops aren't used in any SPI NOR controller. Therefore, remove them
altogether.
Signed-off-by: Michael Walle <michael@walle.cc>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Intel Comet Lake-V has the same SPI serial flash controller as Kaby
Lake. Add Comet Lake-V PCI ID to the driver list of supported devices.
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
The driver is for the HiSilicon FMC (Flash Memory Controller), which
supports SPI NOR in addition other memory technologies, like SPI NAND.
Indeed, the naming in the driver is a little inappropriate, especially
considering that there is already another HiSilicon SPI NOR flash
controller (which I believe the FMC is derived from).
Since we now want to provide software support for this other HiSilicon
controller, update code comments to at least try to make it clear that
this driver is for the FMC.
Signed-off-by: John Garry <john.garry@huawei.com>
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Adds support for sst26vf016b, a smaller variant of the sst26vf064b.
Tested on a sama5d3 SOC using the atmel,at91rm9200-spi controller.
The dual read could not be tested.
SPI_NOR_QUAD_READ is not added because it requires that the IOC bit
from the Configuration Register to be set to 1, which is not the case:
its default value at power-up is zero and we don't set it to one in
spi-nor either.
Signed-off-by: Joseph Kust <joseph.kust@rockwellcollins.com>
Signed-off-by: Brandon Maier <brandon.maier@rockwellcollins.com>
[tudor.ambarus@microchip.com: Drop quad read flag, amend commit description]
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
|
|
Micron flashes do not support 16 bit writes on the Status Register.
According to micron datasheets, when using the Write Status Register
(01h) command, the chip select should be driven LOW and held LOW until
the eighth bit of the last data byte has been latched in, after which
it must be driven HIGH. If CS is not driven HIGH, the command is not
executed, flag status register error bits are not set, and the write enable
latch remains set to 1. This fixes the lock operations on micron flashes.
Reported-by: John Garry <john.garry@huawei.com>
Fixes: 39d1e3340c73 ("mtd: spi-nor: Fix clearing of QE bit on lock()/unlock()")
Signed-off-by: Tudor Ambarus <tudor.ambarus@microchip.com>
Tested-by: John Garry <john.garry@huawei.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
