| Age | Commit message (Collapse) | Author |
|---|
|
Pull UBI/UBIFS updates from Richard Weinberger:
- new config option CONFIG_UBIFS_FS_SECURITY
- minor improvements
- random fixes
* tag 'upstream-4.12-rc1' of git://git.infradead.org/linux-ubifs:
ubi: Add debugfs file for tracking PEB state
ubifs: Fix a typo in comment of ioctl2ubifs & ubifs2ioctl
ubifs: Remove unnecessary assignment
ubifs: Fix cut and paste error on sb type comparisons
ubi: fastmap: Fix slab corruption
ubifs: Add CONFIG_UBIFS_FS_SECURITY to disable/enable security labels
ubi: Make mtd parameter readable
ubi: Fix section mismatch
|
|
Pull MTD updates from Brian Norris:
"NAND, from Boris:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
SPI NOR, from Cyrille:
- fixes in the hisi, intel and Mediatek SPI controller drivers
- fixes to some SPI flash memories not supporting the Chip Erase
command.
- add support to some new memory parts (Winbond, Macronix, Micron,
ESMT).
- add new driver for the STM32 QSPI controller
And a few fixes for Gemini and Versatile platforms on physmap-of"
* tag 'for-linus-20170510' of git://git.infradead.org/linux-mtd: (100 commits)
MAINTAINERS: Update NAND subsystem git repositories
mtd: nand: gpio: update binding
mtd: nand: add ooblayout for old hamming layout
mtd: oxnas_nand: Allocating more than necessary in probe()
dt-bindings: mtd: Document the STM32 QSPI bindings
mtd: mtk-nor: set controller's address width according to nor flash
mtd: spi-nor: add driver for STM32 quad spi flash controller
mtd: nand: brcmnand: Check flash #WP pin status before nand erase/program
mtd: nand: davinci: add comment on NAND subpage write status on keystone
mtd: nand: omap2: Fix partition creation via cmdline mtdparts
mtd: nand: NULL terminate a of_device_id table
mtd: nand: Fix a couple error codes
mtd: nand: allow drivers to request minimum alignment for passed buffer
mtd: nand: allocate aligned buffers if NAND_OWN_BUFFERS is unset
mtd: nand: denali: allow to override revision number
mtd: nand: denali_dt: use pdev instead of ofdev for platform_device
mtd: nand: denali_dt: remove dma-mask DT property
mtd: nand: denali: support 64bit capable DMA engine
mtd: nand: denali_dt: enable HW_ECC_FIXUP for Altera SOCFPGA variant
mtd: nand: denali: support HW_ECC_FIXUP capability
...
|
|
Nandsim has own functions set_memalloc() and clear_memalloc() for robust
setting and clearing of PF_MEMALLOC. Replace them by the new generic
helpers. No functional change.
Link: http://lkml.kernel.org/r/20170405074700.29871-5-vbabka@suse.cz
Signed-off-by: Vlastimil Babka <vbabka@suse.cz>
Cc: Boris Brezillon <boris.brezillon@free-electrons.com>
Cc: Richard Weinberger <richard@nod.at>
Cc: Michal Hocko <mhocko@kernel.org>
Cc: Mel Gorman <mgorman@techsingularity.net>
Cc: Johannes Weiner <hannes@cmpxchg.org>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: Chris Leech <cleech@redhat.com>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: Eric Dumazet <edumazet@google.com>
Cc: Josef Bacik <jbacik@fb.com>
Cc: Lee Duncan <lduncan@suse.com>
Cc: Michal Hocko <mhocko@suse.com>
Cc: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Add a file under debugfs to allow easy access to the erase count for
each physical erase block on an UBI device. This is useful when
debugging data integrity issues with UBIFS on NAND flash devices.
Signed-off-by: Ben Shelton <ben.shelton@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
v2:
* If ubi_io_is_bad eraseblk_count_seq_show just returns the err.
* if ubi->lookuptbl returns null, its no longer treated as an error
instead info for that block is not printeded
* Removed check for UBI_MAX_ERASECOUNTER since it is impossible to hit
* Removed block state from print, if a block is printed then it is good and
if it is not printed, then it is bad.
v3:
* Remove errant ! symbol from if statement checking if erase count is valid.
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Booting with UBI fastmap and SLUB debugging enabled results in the
following splats. The problem is that ubi_scan_fastmap() moves the
fastmap blocks from the scan_ai (allocated in scan_fast()) to the ai
allocated in ubi_attach(). This results in two problems:
- When the scan_ai is freed, aebs which were allocated from its slab
cache are still in use.
- When the other ai is being destroyed in destroy_ai(), the
arguments to kmem_cache_free() call are incorrect since aebs on its
->fastmap list were allocated with a slab cache from a differnt ai.
Fix this by making a copy of the aebs in ubi_scan_fastmap() instead of
moving them.
=============================================================================
BUG ubi_aeb_slab_cache (Not tainted): Objects remaining in ubi_aeb_slab_cache on __kmem_cache_shutdown()
-----------------------------------------------------------------------------
INFO: Slab 0xbfd2da3c objects=17 used=1 fp=0xb33d7748 flags=0x40000080
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<8026c47c>] (slab_err+0x78/0x88)
[<8026c47c>] (slab_err) from [<802735bc>] (__kmem_cache_shutdown+0x180/0x3e0)
[<802735bc>] (__kmem_cache_shutdown) from [<8024e13c>] (shutdown_cache+0x1c/0x60)
[<8024e13c>] (shutdown_cache) from [<8024ed64>] (kmem_cache_destroy+0x19c/0x20c)
[<8024ed64>] (kmem_cache_destroy) from [<8057cc14>] (destroy_ai+0x1dc/0x1e8)
[<8057cc14>] (destroy_ai) from [<8057f04c>] (ubi_attach+0x3f4/0x450)
[<8057f04c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
INFO: Object 0xb33d7e88 @offset=3720
INFO: Allocated in scan_peb+0x608/0x81c age=72 cpu=1 pid=118
kmem_cache_alloc+0x3b0/0x43c
scan_peb+0x608/0x81c
ubi_attach+0x124/0x450
ubi_attach_mtd_dev+0x60c/0xff8
ctrl_cdev_ioctl+0x110/0x2b8
do_vfs_ioctl+0xac/0xa00
SyS_ioctl+0x3c/0x64
ret_fast_syscall+0x0/0x1c
kmem_cache_destroy ubi_aeb_slab_cache: Slab cache still has objects
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<8024ed80>] (kmem_cache_destroy+0x1b8/0x20c)
[<8024ed80>] (kmem_cache_destroy) from [<8057cc14>] (destroy_ai+0x1dc/0x1e8)
[<8057cc14>] (destroy_ai) from [<8057f04c>] (ubi_attach+0x3f4/0x450)
[<8057f04c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
cache_from_obj: Wrong slab cache. ubi_aeb_slab_cache but object is from ubi_aeb_slab_cache
------------[ cut here ]------------
WARNING: CPU: 1 PID: 118 at mm/slab.h:354 kmem_cache_free+0x39c/0x450
Modules linked in:
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<80120e40>] (__warn+0xf4/0x10c)
[<80120e40>] (__warn) from [<80120f20>] (warn_slowpath_null+0x28/0x30)
[<80120f20>] (warn_slowpath_null) from [<80271fe0>] (kmem_cache_free+0x39c/0x450)
[<80271fe0>] (kmem_cache_free) from [<8057cb88>] (destroy_ai+0x150/0x1e8)
[<8057cb88>] (destroy_ai) from [<8057ef1c>] (ubi_attach+0x2c4/0x450)
[<8057ef1c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
---[ end trace 2bd8396277fd0a0b ]---
=============================================================================
BUG ubi_aeb_slab_cache (Tainted: G B W ): page slab pointer corrupt.
-----------------------------------------------------------------------------
INFO: Allocated in scan_peb+0x608/0x81c age=104 cpu=1 pid=118
kmem_cache_alloc+0x3b0/0x43c
scan_peb+0x608/0x81c
ubi_attach+0x124/0x450
ubi_attach_mtd_dev+0x60c/0xff8
ctrl_cdev_ioctl+0x110/0x2b8
do_vfs_ioctl+0xac/0xa00
SyS_ioctl+0x3c/0x64
ret_fast_syscall+0x0/0x1c
INFO: Slab 0xbfd2da3c objects=17 used=1 fp=0xb33d7748 flags=0x40000081
INFO: Object 0xb33d7e88 @offset=3720 fp=0xb33d7da0
Redzone b33d7e80: cc cc cc cc cc cc cc cc ........
Object b33d7e88: 02 00 00 00 01 00 00 00 00 f0 ff 7f ff ff ff ff ................
Object b33d7e98: 00 00 00 00 00 00 00 00 bd 16 00 00 00 00 00 00 ................
Object b33d7ea8: 00 01 00 00 00 02 00 00 00 00 00 00 00 00 00 00 ................
Redzone b33d7eb8: cc cc cc cc ....
Padding b33d7f60: 5a 5a 5a 5a 5a 5a 5a 5a ZZZZZZZZ
CPU: 1 PID: 118 Comm: ubiattach Tainted: G B W 4.9.15 #3
[<80111910>] (unwind_backtrace) from [<8010d498>] (show_stack+0x18/0x1c)
[<8010d498>] (show_stack) from [<804a3274>] (dump_stack+0xb4/0xe0)
[<804a3274>] (dump_stack) from [<80271770>] (free_debug_processing+0x320/0x3c4)
[<80271770>] (free_debug_processing) from [<80271ad0>] (__slab_free+0x2bc/0x430)
[<80271ad0>] (__slab_free) from [<80272024>] (kmem_cache_free+0x3e0/0x450)
[<80272024>] (kmem_cache_free) from [<8057cb88>] (destroy_ai+0x150/0x1e8)
[<8057cb88>] (destroy_ai) from [<8057ef1c>] (ubi_attach+0x2c4/0x450)
[<8057ef1c>] (ubi_attach) from [<8056fe70>] (ubi_attach_mtd_dev+0x60c/0xff8)
[<8056fe70>] (ubi_attach_mtd_dev) from [<80571d78>] (ctrl_cdev_ioctl+0x110/0x2b8)
[<80571d78>] (ctrl_cdev_ioctl) from [<8029c77c>] (do_vfs_ioctl+0xac/0xa00)
[<8029c77c>] (do_vfs_ioctl) from [<8029d10c>] (SyS_ioctl+0x3c/0x64)
[<8029d10c>] (SyS_ioctl) from [<80108860>] (ret_fast_syscall+0x0/0x1c)
FIX ubi_aeb_slab_cache: Object at 0xb33d7e88 not freed
Signed-off-by: Rabin Vincent <rabinv@axis.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Fix permissions to allow read mtd parameter back (only for owner).
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
WARNING: vmlinux.o(.text+0x1f2a80): Section mismatch in reference from the variable __param_ops_mtd to the function .init.text:ubi_mtd_param_parse()
The function __param_ops_mtd() references
the function __init ubi_mtd_param_parse().
This is often because __param_ops_mtd lacks a __init
annotation or the annotation of ubi_mtd_param_parse is wrong.
Cc: Richard Weinberger <richard@nod.at>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
Pull block fixes and updates from Jens Axboe:
"Some fixes and followup features/changes that should go in, in this
merge window. This contains:
- Two fixes for lightnvm from Javier, fixing problems in the new code
merge previously in this merge window.
- A fix from Jan for the backing device changes, fixing an issue in
NFS that causes a failure to mount on certain setups.
- A change from Christoph, cleaning up the blk-mq init and exit
request paths.
- Remove elevator_change(), which is now unused. From Bart.
- A fix for queue operation invocation on a dead queue, from Bart.
- A series fixing up mtip32xx for blk-mq scheduling, removing a
bandaid we previously had in place for this. From me.
- A regression fix for this series, fixing a case where we wait on
workqueue flushing from an invalid (non-blocking) context. From me.
- A fix/optimization from Ming, ensuring that we don't both quiesce
and freeze a queue at the same time.
- A fix from Peter on lock ordering for CPU hotplug. Not a real
problem right now, but will be once the CPU hotplug rework goes in.
- A series from Omar, cleaning up out blk-mq debugfs support, and
adding support for exporting info from schedulers in debugfs as
well. This is really useful in debugging stalls or livelocks. From
Omar"
* 'for-linus' of git://git.kernel.dk/linux-block: (28 commits)
mq-deadline: add debugfs attributes
kyber: add debugfs attributes
blk-mq-debugfs: allow schedulers to register debugfs attributes
blk-mq: untangle debugfs and sysfs
blk-mq: move debugfs declarations to a separate header file
blk-mq: Do not invoke queue operations on a dead queue
blk-mq-debugfs: get rid of a bunch of boilerplate
blk-mq-debugfs: rename hw queue directories from <n> to hctx<n>
blk-mq-debugfs: don't open code strstrip()
blk-mq-debugfs: error on long write to queue "state" file
blk-mq-debugfs: clean up flag definitions
blk-mq-debugfs: separate flags with |
nfs: Fix bdi handling for cloned superblocks
block/mq: Cure cpu hotplug lock inversion
lightnvm: fix bad back free on error path
lightnvm: create cmd before allocating request
blk-mq: don't use sync workqueue flushing from drivers
mtip32xx: convert internal commands to regular block infrastructure
mtip32xx: cleanup internal tag assumptions
block: don't call blk_mq_quiesce_queue() after queue is frozen
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the big set of new char/misc driver drivers and features for
4.12-rc1.
There's lots of new drivers added this time around, new firmware
drivers from Google, more auxdisplay drivers, extcon drivers, fpga
drivers, and a bunch of other driver updates. Nothing major, except if
you happen to have the hardware for these drivers, and then you will
be happy :)
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.12-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (136 commits)
firmware: google memconsole: Fix return value check in platform_memconsole_init()
firmware: Google VPD: Fix return value check in vpd_platform_init()
goldfish_pipe: fix build warning about using too much stack.
goldfish_pipe: An implementation of more parallel pipe
fpga fr br: update supported version numbers
fpga: region: release FPGA region reference in error path
fpga altera-hps2fpga: disable/unprepare clock on error in alt_fpga_bridge_probe()
mei: drop the TODO from samples
firmware: Google VPD sysfs driver
firmware: Google VPD: import lib_vpd source files
misc: lkdtm: Add volatile to intentional NULL pointer reference
eeprom: idt_89hpesx: Add OF device ID table
misc: ds1682: Add OF device ID table
misc: tsl2550: Add OF device ID table
w1: Remove unneeded use of assert() and remove w1_log.h
w1: Use kernel common min() implementation
uio_mf624: Align memory regions to page size and set correct offsets
uio_mf624: Refactor memory info initialization
uio: Allow handling of non page-aligned memory regions
hangcheck-timer: Fix typo in comment
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree updates from Jiri Kosina.
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
tty: fix comment for __tty_alloc_driver()
init/main: properly align the multi-line comment
init/main: Fix double "the" in comment
Fix dead URLs to ftp.kernel.org
drivers: Clean up duplicated email address
treewide: Fix typo in xml/driver-api/basics.xml
tools/testing/selftests/powerpc: remove redundant CFLAGS in Makefile: "-Wall -O2 -Wall" -> "-O2 -Wall"
selftests/timers: Spelling s/privledges/privileges/
HID: picoLCD: Spelling s/REPORT_WRTIE_MEMORY/REPORT_WRITE_MEMORY/
net: phy: dp83848: Fix Typo
UBI: Fix typos
Documentation: ftrace.txt: Correct nice value of 120 priority
net: fec: Fix typo in error msg and comment
treewide: Fix typos in printk
|
|
The old 1-bit hamming layout requires ECC data to be placed at a
fixed offset, and not necessarily at the end of the OOB area.
Add this old layout back in order to fix legacy setups.
Fixes: 41b207a70d3a ("mtd: nand: implement the default mtd_ooblayout_ops")
Cc: <stable@vger.kernel.org>
Signed-off-by: Alexander Couzens <lynxis@fe80.eu>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
We only need to allocate sizeof(struct oxnas_nand_ctrl) which is 192
bytes and not sizeof(struct nand_chip) which is a much larger 3056
bytes.
Fixes: 668592492409 ("mtd: nand: Add OX820 NAND Support")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Remove the request_idx parameter, which can't be used safely now that we
support I/O schedulers with blk-mq. Except for a superflous check in
mtip32xx it was unused anyway.
Also pass the tag_set instead of just the driver data - this allows drivers
to avoid some code duplication in a follow on cleanup.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
From Cyrille:
"""
This pull request contains the following notable changes:
- fixes in the hisi SPI controller driver.
- fixes in the intel SPI controller driver.
- fixes in the Mediatek SPI controller driver.
- fixes to some SPI flash memories not supported the Chip Erase command.
- add support to some new memory parts (Winbond, Macronix, Micron, ESMT).
- add new driver for the STM32 QSPI controller.
"""
|
|
From Boris:
"""
This pull request contains:
- some minor fixes/improvements on existing drivers (fsmc, gpio, ifc,
davinci, brcmnand, omap)
- a huge cleanup/rework of the denali driver accompanied with core
fixes/improvements to simplify the driver code
- a complete rewrite of the atmel driver to support new DT bindings
make future evolution easier
- the addition of per-vendor detection/initialization steps to avoid
extending the nand_ids table with more extended-id entries
"""
|
|
Pull block layer updates from Jens Axboe:
- Add BFQ IO scheduler under the new blk-mq scheduling framework. BFQ
was initially a fork of CFQ, but subsequently changed to implement
fairness based on B-WF2Q+, a modified variant of WF2Q. BFQ is meant
to be used on desktop type single drives, providing good fairness.
From Paolo.
- Add Kyber IO scheduler. This is a full multiqueue aware scheduler,
using a scalable token based algorithm that throttles IO based on
live completion IO stats, similary to blk-wbt. From Omar.
- A series from Jan, moving users to separately allocated backing
devices. This continues the work of separating backing device life
times, solving various problems with hot removal.
- A series of updates for lightnvm, mostly from Javier. Includes a
'pblk' target that exposes an open channel SSD as a physical block
device.
- A series of fixes and improvements for nbd from Josef.
- A series from Omar, removing queue sharing between devices on mostly
legacy drivers. This helps us clean up other bits, if we know that a
queue only has a single device backing. This has been overdue for
more than a decade.
- Fixes for the blk-stats, and improvements to unify the stats and user
windows. This both improves blk-wbt, and enables other users to
register a need to receive IO stats for a device. From Omar.
- blk-throttle improvements from Shaohua. This provides a scalable
framework for implementing scalable priotization - particularly for
blk-mq, but applicable to any type of block device. The interface is
marked experimental for now.
- Bucketized IO stats for IO polling from Stephen Bates. This improves
efficiency of polled workloads in the presence of mixed block size
IO.
- A few fixes for opal, from Scott.
- A few pulls for NVMe, including a lot of fixes for NVMe-over-fabrics.
From a variety of folks, mostly Sagi and James Smart.
- A series from Bart, improving our exposed info and capabilities from
the blk-mq debugfs support.
- A series from Christoph, cleaning up how handle WRITE_ZEROES.
- A series from Christoph, cleaning up the block layer handling of how
we track errors in a request. On top of being a nice cleanup, it also
shrinks the size of struct request a bit.
- Removal of mg_disk and hd (sorry Linus) by Christoph. The former was
never used by platforms, and the latter has outlived it's usefulness.
- Various little bug fixes and cleanups from a wide variety of folks.
* 'for-4.12/block' of git://git.kernel.dk/linux-block: (329 commits)
block: hide badblocks attribute by default
blk-mq: unify hctx delay_work and run_work
block: add kblock_mod_delayed_work_on()
blk-mq: unify hctx delayed_run_work and run_work
nbd: fix use after free on module unload
MAINTAINERS: bfq: Add Paolo as maintainer for the BFQ I/O scheduler
blk-mq-sched: alloate reserved tags out of normal pool
mtip32xx: use runtime tag to initialize command header
scsi: Implement blk_mq_ops.show_rq()
blk-mq: Add blk_mq_ops.show_rq()
blk-mq: Show operation, cmd_flags and rq_flags names
blk-mq: Make blk_flags_show() callers append a newline character
blk-mq: Move the "state" debugfs attribute one level down
blk-mq: Unregister debugfs attributes earlier
blk-mq: Only unregister hctxs for which registration succeeded
blk-mq-debugfs: Rename functions for registering and unregistering the mq directory
blk-mq: Let blk_mq_debugfs_register() look up the queue name
blk-mq: Register <dev>/queue/mq after having registered <dev>/queue
ide-pm: always pass 0 error to ide_complete_rq in ide_do_devset
ide-pm: always pass 0 error to __blk_end_request_all
..
|
|
When nor's size larger than 16MByte, nor's address width maybe
set to 3 or 4, and controller should change address width according
to nor's setting.
Signed-off-by: Guochun Mao <guochun.mao@mediatek.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
|
|
The quadspi is a specialized communication interface targeting single,
dual or quad SPI Flash memories.
It can operate in any of the following modes:
-indirect mode: all the operations are performed using the quadspi
registers
-read memory-mapped mode: the external Flash memory is mapped to the
microcontroller address space and is seen by the system as if it was
an internal memory
Signed-off-by: Ludovic Barre <ludovic.barre@st.com>
Reviewed-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
|
|
On brcmnand controller v6.x and v7.x, the #WP pin is controlled through
the NAND_WP bit in CS_SELECT register.
The driver currently assumes that toggling the #WP pin is
instantaneously enabling/disabling write-protection, but it actually
takes some time to propagate the new state to the internal NAND chip
logic. This behavior is sometime causing data corruptions when an
erase/program operation is executed before write-protection has really
been disabled.
Fixes: 27c5b17cd1b1 ("mtd: nand: add NAND driver "library" for Broadcom STB NAND controller")
Signed-off-by: Kamal Dasu <kdasu.kdev@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Add a comment clarifying that NAND subpage write on keystone works,
but is not being enabled in the interest of backward compatibility.
Signed-off-by: Sekhar Nori <nsekhar@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
commit c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
caused the parent device name to be changed from "omap2-nand.0"
to "<base address>.nand" (e.g. 30000000.nand on omap3 platforms).
This caused mtd->name to be changed as well. This breaks partition
creation via mtdparts passed by u-boot as it uses "omap2-nand.0"
for the mtd-id.
Fix this by explicitly setting the mtd->name to "omap2-nand.<CS number>"
if it isn't already set by nand_set_flash_node(). CS number is the
NAND controller instance ID.
Fixes: c9711ec5250b ("mtd: nand: omap: Clean up device tree support")
Cc: <stable@vger.kernel.org> # 4.7+
Reported-by: Leto Enrico <enrico.leto@siemens.com>
Reported-by: Adam Ford <aford173@gmail.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
of_device_id tables should be NULL terminated.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
We accidentally return 1 on error instead of proper error codes.
Fixes: 07b23e3db9ed ("mtd: nand: Cleanup/rework the atmel_nand driver")
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
In some cases, nand_do_{read,write}_ops is passed with unaligned
ops->datbuf. Drivers using DMA will be unhappy about unaligned
buffer.
The new struct member, buf_align, represents the minimum alignment
the driver require for the buffer. If the buffer passed from the
upper MTD layer does not have enough alignment, nand_do_*_ops will
use bufpoi.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some NAND controllers are using DMA engine requiring a specific
buffer alignment. The core provides no guarantee on the nand_buffers
pointers, which forces some drivers to allocate their own buffers
and pass the NAND_OWN_BUFFERS flag.
Rework the nand_buffers allocation logic to allocate each buffer
independently. This should make most NAND controllers/DMA engine
happy, and allow us to get rid of these custom buf allocation in
NAND controller drivers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 271707b1d817 ("mtd: nand: denali: max_banks calculation
changed in revision 5.1") added a revision check to support the
new max_banks encoding. Its git-log states "The encoding of
max_banks changed in Denali revision 5.1".
There are exceptional cases, for example, the revision register on
some UniPhier SoCs says the IP is 5.0 but the max_banks is encoded
in the new format.
This IP updates the resister specification from time to time (often
breaking the backward compatibility), but the revision number is not
incremented correctly.
The max_banks is not only the case that needs revision checking.
Let's allow to override an incorrect revision number.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
"pdev" is much more often used to point a platform_device, so this
will help the driver code look consistent across the kernel.
While we are here, fix "line over 80 characters" coding style
violations.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The driver sets appropriate DMA mask. Delete the "dma-mask" DT
property. See [1] for negative comments for this binding.
[1] https://lkml.org/lkml/2016/2/8/57
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The current driver only supports the DMA engine up to 32 bit
physical address, but there also exists 64 bit capable DMA engine
for this IP.
The data DMA setup sequence is completely different, so I added the
64 bit DMA code as a new function denali_setup_dma64(). The 32 bit
one has been renamed to denali_setup_dma32().
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
There are various customizable parameters, so several variants for
this IP. A generic compatible like "denali,denali-nand-dt" is
useless. Moreover, there are multiple things wrong with this string.
(Refer to Rob's comment [1])
The "denali,denali-nand-dt" was added by Altera for the SOCFPGA port.
Replace it with a more specific string "altr,socfpga-denali-nand".
There are no users (in upstream) of the old compatible string.
The Denali IP on SOCFPGA incorporates the hardware ECC fixup engine.
So, this capability should be associated with the compatible.
[1] https://lkml.org/lkml/2016/12/1/450
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Some old versions of the Denali IP (perhaps used only for Intel?)
detects ECC errors and provides correct data via a register, but
does not touch the transferred data. So, the software must fixup
the data in the buffer according to the provided ECC correction
information.
Newer versions perform ECC correction before transferring the data.
No more software intervention is needed. The ECC_ERROR_ADDRESS and
ECC_CORRECTION_INFO registers were deprecated. Instead, the number
of corrected bit-flips are reported via the ECC_COR_INFO register.
When an uncorrectable ECC error happens, a status flag is set to the
INTR_STATUS and ECC_COR_INFO registers.
As is often the case with this IP, the register view of INTR_STATUS
had broken compatibility.
For older versions (SW ECC fixup):
bit 0: ECC_TRANSACTION_DONE
bit 1: ECC_ERR
For newer versions (HW ECC fixup):
bit 0: ECC_UNCOR_ERR
bit 1: Reserved
Due to this difference, the irq_mask must be fixed too.
The existing handle_ecc() has been renamed to denali_sw_ecc_fixup()
for clarification.
What is unfortunate with this feature is we can not know the total
number of corrected/uncorrected errors in a page. The register
ECC_COR_INFO reports the maximum of per-sector bitflips. This is
useful for ->read_page return value, but ecc_stats.{corrected,failed}
increments may not be precise.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This part is wrong in multiple ways:
[1] is_erased() is called against "buf" twice, so the OOB area is
not checked at all. The second call should check chip->oob_poi.
[2] This code block is nested by double "if (check_erase_page)".
The inner one is redundant.
[3] The ECC_ERROR_ADDRESS register reports which sector(s) had
uncorrectable ECC errors. It is pointless to check the whole page
if only one sector contains errors.
[4] Unfortunately, the Denali ECC correction engine has already
manipulated the data buffer before it decides the bitflips are
uncorrectable. That is, not all of the data are 0xFF after an
erased page is processed by the ECC engine. The current is_erased()
helper could report false-positive ECC errors. Actually, a certain
mount of bitflips are allowed in an erased page. The core framework
provides nand_check_erased_ecc_chunk() that takes the threshold into
account. Let's use this.
This commit reworks the code to solve those problems.
Please note the erased page checking is implemented as a separate
helper function instead of embedding it in the loop in handle_ecc().
The reason is that OOB data are needed for the erased page checking,
but the controller can not start a new transaction until all ECC
error information is read out from the registers.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
This function is wrong in multiple ways:
[1] Counting corrected bytes instead of corrected bits.
The following code is counting the number of corrected _bytes_.
/* correct the ECC error */
buf[offset] ^= err_cor_value;
mtd->ecc_stats.corrected++;
bitflips++;
What the core framework expects is the number of corrected _bits_.
They can be different if multiple bitflips occur within one byte.
[2] total number of errors instead of max of per-sector errors
The core framework expects that corrected errors are counted per
sector, then the max value should be taken. The current code simply
iterates over the whole page, i.e. counts the total number of
correction in the page. This means "too many bitflips" is triggered
earlier than it should be, i.e. the NAND device is worn out sooner.
Besides those bugs, this function is unreadable due to the deep
nesting. Notice the whole code in this function is wrapped in
if (irq_status & INTR__ECC_ERR), so this conditional can be moved
out of the function. Also, use shorter names for local variables.
Re-work the function to fix all the issues.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The pipeline read-ahead function of the Denali IP enables continuous
reading from the device; while data is being read out by a CPU, the
controller maintains additional commands for streaming data from the
device. This will reduce the latency of the second page or later.
This feature is obviously no help for per-page accessors of Linux
NAND driver interface.
In the current implementation, the pipeline command is issued to
load a single page, then data are read out immediately. The use of
the pipeline operation is not adding any advantage, but just adding
complexity to the code. Remove.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Commit 28309572aac4 ("mtd: name the mtd device with an optional
label property") allow us to identify a chip in a user-friendly way.
If nand_set_flash_node() picks up the "label" from DT, let's respect
it. Otherwise, let it fallback to the current name "denali-nand".
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The comment for ecc.read_page() requires that it should return
"0 if bitflips uncorrectable".
Actually, drivers could return positive values when uncorrectable
bitflips occur. For example, nand_read_page_swecc() is the case.
If ecc.correct() returns -EBADMSG for the first ECC sector, and
a positive value for the second one, nand_read_page_swecc() returns
a positive max_bitflips and increments ecc_stats.failed for the same
page.
The requirement can be relaxed by tweaking nand_do_read_ops().
Move the max_bitflips calculation below the retry.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
The last/only user of the chip->write_page() hook (the Atmel NAND
controller driver) has been reworked and is no longer specifying a custom
->write_page() implementation.
Drop this hook before someone else start abusing it.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
|
|
This is a complete rewrite of the driver whose main purpose is to
support the new DT representation where the NAND controller node is now
really visible in the DT and appears under the EBI bus. With this new
representation, we can add other devices under the EBI bus without
risking pinmuxing conflicts (the NAND controller is under the EBI
bus logic and as such, share some of its pins with other devices
connected on this bus).
Even though the goal of this rework was not necessarily to add new
features, the new driver has been designed with this in mind. With a
clearer separation between the different blocks and different IP
revisions, adding new functionalities should be easier (we already
have plans to support SMC timing configuration so that we no longer
have to rely on the configuration done by the bootloader/bootstrap).
Also note that we no longer have a custom ->cmdfunc() implementation,
which means we can now benefit from new features added in the core
implementation for free (support for new NAND operations for example).
The last thing that we gain with this rework is support for multi-chips
and multi-dies chips, thanks to the clean NAND controller <-> NAND
devices representation.
During this transition we also dropped support for AVR32 SoCs which
should soon disappear from mainline (removal of the AVR32 arch is
planned for 4.12).
This new driver has been tested on several platforms (at91sam9261,
at91sam9g45, at91sam9x5, sama5d3 and sama5d4) to make sure it did not
introduce regressions, and it's worth mentioning that old bindings are
still supported (which partly explain the positive diffstat).
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
|
|
Drop 'parent' argument of bdi_register() and bdi_register_va(). It is
always NULL.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Now that all bdi structures filesystems use are properly refcounted, we
can remove the SB_I_DYNBDI flag.
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
MTD already allocates backing_dev_info dynamically. Convert it to use
generic infrastructure for this including proper refcounting. We drop
mtd->backing_dev_info as its only use was to pass mtd_bdi pointer from
one file into another and if we wanted to keep that in a clean way, we'd
have to make mtd hold and drop bdi reference as needed which seems
pointless for passing one global pointer...
CC: David Woodhouse <dwmw2@infradead.org>
CC: Brian Norris <computersforpeace@gmail.com>
CC: linux-mtd@lists.infradead.org
Reviewed-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
OF core code provides helpers for counting strings and reading them so
use them instead of doing this manually. This simplifies the code a bit.
Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Reviewed-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
Since macros MTDSWAP_ECNT_MIN() and MTDSWAP_ECNT_MAX() have been
defined in mtdswap.c, use them instead of open-coding.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/mtd
Prior to this patch, there were 7 uses of pr_warning and
31 uses of pr_warn in drivers/mtd
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
The current way of building the of_physmap add-ons result in just
the add-on being in the object code, and not the actual core
implementation and regress the Gemini and Versatile.
Bake the physmap_of.o object by baking physmap_of_core.o and
adding the Versatile and/or Gemini add-ons to the final object.
Rename the source file physmap_of_core.c to get the desired
build components.
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Fixes: 4f04f68e1598 ("mtd: physmap_of: fixup gemini/versatile dependencies")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
All required stateless 4-byte op codes are supported by this flash
chip. The stateless 4-byte support can't be autodetected due to a
missing 4-byte Address Instruction Table in SFDP.
Fixes hangs on reboot for SoCs expecting the flash chip in 3byte mode.
Signed-off-by: Mathias Kresin <dev@kresin.me>
Acked-by: Marek Vasut <marek.vasut@gmail.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
|
|
Add new Micron N25Q256A (N25Q256A11) 256Mbit NOR Flash in the list
of supported devices. This chip has the same structure as the N25Q256A
but ID and voltage (1V8) to use is different. Therefore, this adds
N25Q256A11 as n25q256ax1.
In the future, for new Micron memories we could use the patterns
"n25q*ax1" for 1V8 and "n25q*ax3" for 3V3 memories.
Signed-off-by: Nobuhiro Iwamatsu <nobuhiro.iwamatsu.kw@hitachi.com>
Signed-off-by: Cyrille Pitchen <cyrille.pitchen@atmel.com>
|
|
Constify all instances of blk_mq_ops, as they are never modified.
Signed-off-by: Eric Biggers <ebiggers@google.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
In commit 6afaf8a484cb ("UBI: flush wl before clearing update marker") I
managed to trigger and fix a similar bug. Now here is another version of
which I assumed it wouldn't matter back then but it turns out UBI has a
check for it and will error out like this:
|ubi0 warning: validate_vid_hdr: inconsistent used_ebs
|ubi0 error: validate_vid_hdr: inconsistent VID header at PEB 592
All you need to trigger this is? "ubiupdatevol /dev/ubi0_0 file" + a
powercut in the middle of the operation.
ubi_start_update() sets the update-marker and puts all EBs on the erase
list. After that userland can proceed to write new data while the old EB
aren't erased completely. A powercut at this point is usually not that
much of a tragedy. UBI won't give read access to the static volume
because it has the update marker. It will most likely set the corrupted
flag because it misses some EBs.
So we are all good. Unless the size of the image that has been written
differs from the old image in the magnitude of at least one EB. In that
case UBI will find two different values for `used_ebs' and refuse to
attach the image with the error message mentioned above.
So in order not to get in the situation, the patch will ensure that we
wait until everything is removed before it tries to write any data.
The alternative would be to detect such a case and remove all EBs at the
attached time after we processed the volume-table and see the
update-marker set. The patch looks bigger and I doubt it is worth it
since usually the write() will wait from time to time for a new EB since
usually there not that many spare EB that can be used.
Cc: stable@vger.kernel.org
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Signed-off-by: Richard Weinberger <richard@nod.at>
|
|
The clock gate used by orion_nand is not available on all platforms.
When getting this optional clock gate, the code masked all errors.
Let's be more precise here and actually only allow ENOENT.
EPROBE_DEFER is handled like any other error code since probe deferral
is not supported by drivers using module_platform_driver_probe().
Signed-off-by: Simon Baatz <gmbnomis@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
