summaryrefslogtreecommitdiff
path: root/drivers/mtd/nand
AgeCommit message (Collapse)Author
2009-04-06[MTD] [NAND] FSL-UPM: Add wait flags to support board/chip specific delaysWolfgang Grandegger
The NAND flash on the TQM8548_BE modules requires a short delay after running the UPM pattern. The TQM8548_BE requires a further short delay after writing out a buffer. Normally the R/B pin should be checked, but it's not connected on the TQM8548_BE. The existing driver uses similar fixed delay points. To manage these extra delays in a more general way, I introduced the "fsl,ump-wait-flags" property allowing the board- specific driver to specify various types of extra delay. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] FSL-UPM: add multi chip supportWolfgang Grandegger
This patch adds support for multi-chip NAND devices to the FSL-UPM driver. This requires support for multiple GPIOs for the RNB pins. The NAND chips are selected through address lines defined by the FDT property "fsl,upm-addr-line-cs-offsets". Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Acked-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] Add support for NAND on the Socrates boardWolfgang Grandegger
Signed-off-by: Ilya Yanok <yanok@emcraft.com> Acked-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-06[MTD] [NAND] Add support for 4KiB pages.Thomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Sebastian Siewior <bigeasy@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-04[MTD] [NAND] Add parent info for CAFÉ controllerDavid Woodhouse
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-04[MTD] support driver model updatesDavid Brownell
Follow-on patch to the previous driver model patch for the MTD framework. This one makes various MTD drivers connect to the driver model tree, so /sys/devices/virtual/mtd/* nodes are no longer present ... mostly drivers used on boards I have handy. Based on a patch from Kay Sievers. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-04-03[MTD] [NAND] move gen_nand's probe function to .devinit.textUwe Kleine-König
A pointer to plat_nand_probe is passed to the core via platform_driver_register and so the function must not disappear when the .init sections are discarded. Otherwise (if also having HOTPLUG=y) unbinding and binding a device to the driver via sysfs will result in an oops as does a device being registered late. An alternative to this patch is using platform_driver_probe instead of platform_driver_register plus removing the pointer to the probe function from the struct platform_driver. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Cc: Kay Sievers <kay.sievers@vrfy.org> Cc: Hamish Moffatt <hamish@cloud.net.au> Cc: David Brownell <dbrownell@users.sourceforge.net> Cc: Andrew Morton <akpm@linux-foundation.org> Cc: Li Zefan <lizf@cn.fujitsu.com> Cc: Vitaly Wool <vitalywool@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-24[MTD] [NAND] sh_flctl: fix hardware ecc handling for 2048 byte pageYoshihiro Shimoda
Signed-off-by: Jeremy Baker <Jeremy.Baker@renesas.com> Signed-off-by: Yoshihiro Shimoda <shimoda.yoshihiro@renesas.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: add ability to keep controller settings defined by ↵Mike Rapoport
OBM/bootloader Signed-off-by: Mike Rapoport <mike@compulab.co.il> Acked-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: allow building as moduleMike Rapoport
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] pxa3xx_nand: use resource_size instead of 'r->end - r->start + 1'Mike Rapoport
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] TXx9 SoC NAND Flash Memory Controller driverAtsushi Nemoto
This patch adds support for the integrated NAND flash controller of the TXx9 family. Once upon a time there were tx4925ndfmc and tx4938ndfmc driver. They were removed due to bitrot in 2005. This new driver is completely rewritten based on a driver in CELF patch archive. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Cc: Ralf Bächle <ralf@linux-mips.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] partitioning utility predicatesDavid Brownell
Move mtd_has_partitions() and mtd_has_cmdlinepart() inlines from a DaVinci-specific driver to the <linux/mtd/partitions.h> header. Use those to eliminate #ifdefs in two drivers which had their own definitions of mtd_has_partitions(). Quite a lot of other MTD drivers could benefit from using use one or both of these to remove #ifdeffery. Maybe some Janitors would like to help. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] davinci: drop usage of cpu_is_* macroKevin Hilman
Usage of davinci-specific cpu_is macros is not allowed in drivers. These options should be passed in through platform_data. Signed-off-by: Kevin Hilman <khilman@deeprootsystems.com> Cc: David Brownell <david-b@pacbell.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] fix broken debug messagesDavid Brownell
Fix incorrect debug messages (*write* not read); someone committed some cut'n'paste bugs.  There might be more, I only noticed these since I was looking for nand_read usage and landed in some very wrong functions. IMO all MTD debugging message framework is goofed, anyway. It uses "DEBUG" in a way that's incompatible with usage most everywhere else in the kernel, and which prevents normal pr_dbg() and dev_dbg() calls from working right. [True. It predates those by a long way, and should probably be updated to use them. dwmw2] Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] davinci_nand driverDavid Brownell
This is a device driver for the NAND flash controller found on the various DaVinci family chips. It handles up to four SoC chipselects, and some flavors of secondary chipselect (e.g. based on upper bits of the address bus) as used with some multichip packages. (Including the 2 GiB chips used on some TI devel boards.) The 1-bit ECC hardware is supported (3 bytes ECC per 512 bytes data); but not yet the newer 4-bit ECC (10 bytes ECC per 512 bytes data), as available on chips like the DM355 or OMAP-L137 and needed with the more error-prone MLC NAND chips. This is a cleaned-up version of code that's been in use for several years now; sanity checked with the new drivers/mtd/tests. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Sudhakar Rajashekhara <sudhakar.raj@ti.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] fix "raw" reads with ECC syndrome layoutsDavid Brownell
The syndrome based page read/write routines store ECC, and possibly other "OOB" data, right after each chunk of ECC'd data. With ECC chunk size of 512 bytes and a large page (2KiB) NAND, the layout is: data-0 OOB-0 data-1 OOB-1 data-2 OOB-2 data-3 OOB-3 OOB-leftover Where OOBx is (prepad, ECC, postpad). However, the current "raw" routines use a traditional layout -- data OOB, disregarding the prepad and postpad values -- so when they're used with that type of ECC hardware, those calls mix up the data and OOB. Which means, in particular, that bad block tables won't be found on startup, with data corruption and related chaos ensuing. The current syndrome-based drivers in mainline all seem to use one chunk per page; presumably they haven't noticed such bugs. Fix this, by adding read/write page_raw_syndrome() routines as siblings of the existing non-raw routines; "raw" just means to bypass the ECC computations, not change data and OOB layout. Signed-off-by: David Brownell <dbrownell@users.sourceforge.net> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: drop pointless casts with set_dma_callback()Mike Frysinger
Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: mark bf5xx_nand_add_partition() as __devinitMike Frysinger
The bf5xx_nand_add_partition() func is only called by __devinit functions, so put it into the __devinit section as well Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [NAND] Blackfin NFC Driver: do not clobber DMAC1_PERIMUXMike Frysinger
Only set DMAC1_PERIMUX once we have requested and been granted the dma channel to prevent breaking other peripherals in the error case Signed-off-by: Mike Frysinger <vapier.adi@gmail.com> Signed-off-by: Bryan Wu <cooloney@kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-03[ARM] fix lots of ARM __devexit sillynessRussell King
`iop_adma_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv_xor_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv64xxx_i2c_unmap_regs' referenced in section `.devinit.text' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `mv64xxx_i2c_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `orion_nand_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o `pxafb_remove' referenced in section `.data' of drivers/built-in.o: defined in discarded section `.devexit.text' of drivers/built-in.o Acked-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-02-16[ARM] 5400/1: Add support for inverted rdy_busy pin for Atmel nand device ↵Gregory CLEMENT
controller Add support for inverted rdy_busy pin for Atmel nand device controller It will fix building error on NeoCore926 board. Acked-by: Andrew Victor <linux@maxim.org.za> Acked-by: David Woodhouse <David.Woodhouse@intel.com> Signed-off-by: Gregory CLEMENT <gclement@adeneo.adetelgroup.com> Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2009-01-28powerpc: More printing warning fixes for the l64 to ll64 conversionStephen Rothwell
These are all powerpc specific drivers. res.start in fsl_elbc_nand.c needs to be cast since it may be either 32 or 64 bit. Thanks to Scott Wood for noticing. Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au> Acked-by: Arnd Bergmann <arnd@arndb.de> call_edac bits in particular Acked-by: Olof Johansson <olof@lixom.net> pasemi_nand peices Acked-by: Scott Wood <scottwood@freescale.com> fsl_elbc fixes Signed-off-by: Benjamin Herrenschmidt <benh@kernel.crashing.org>
2009-01-09[MTD] [NAND] add cmdline parsing (mtdparts=) support to cafe_nandPhilip Rakity
[dwmw2: updated and made to still register whole device first] Signed-off-by: Philip Rakity <pakity@yahoo.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] ndfc driverSean MacLennan
The current ndfc driver only compiles under arch/ppc. This arch was removed from the kernel. I notice the event entry for the ndfc in Kconfig has been removed in 2.6.28. This patch converts the ndfc to a proper OF (OpenFirmware) driver. I can give a working example of the DTS if needed. The patch has been in production use on the PIKA Warp Appliance and is in use by others. The Warp basically boots from NAND, so the ndfc driver is very important to us. Signed-off-by: Sean MacLennan <smaclennan@pikatech.com> Acked-By: Josh Boyer <jwboyer@linux.vnet.ibm.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] pxa3xx: convert from ns to clock ticks more accuratelyMatt Reimer
The various fields in NDTR{01} are in units of clock ticks minus one, but the ns2cycle macro mistakenly adds one, inflating the number of clock ticks and making it impossible to set any of these fields to zero. Signed-off-by: Matt Reimer <mreimer@vpop.net> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] pxa3xx: fix non-page-aligned readsMatt Reimer
Reads from non-page-aligned addresses were broken because while the address to read from was correctly written to NDCB*, a full page was always read. Fix this by ignoring the column and only using the page address. I suspect this whole-page behavior is due to the controller's need to read the entire page in order to generate correct ECC. In the non-ECC case this could be optimized to use the column address, and to set the read length to what is being requested rather than the length of an entire page. Signed-off-by: Matt Reimer <mreimer@vpop.net> Signed-off-by: Eric Miao <eric.miao@marvell.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] fix nandsim sched.h referencesRandy Dunlap
Fix sched.h references: build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1326: error: 'PF_MEMALLOC' undeclared (first use in this function) build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1328: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: dereferencing pointer to incomplete type build-r7149.out:/local/linsrc/linux-next-20081215/drivers/mtd/nand/nandsim.c:1335: error: 'PF_MEMALLOC' undeclared (first use in this function) build-r7149.out:make[4]: *** [drivers/mtd/nand/nandsim.o] Error 1 Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05[MTD] [NAND] alauda: use USB API functions rather than constantsJulia Lawall
This set of patches introduces calls to the following set of functions: usb_endpoint_dir_in(epd) usb_endpoint_dir_out(epd) usb_endpoint_is_bulk_in(epd) usb_endpoint_is_bulk_out(epd) usb_endpoint_is_int_in(epd) usb_endpoint_is_int_out(epd) usb_endpoint_num(epd) usb_endpoint_type(epd) usb_endpoint_xfer_bulk(epd) usb_endpoint_xfer_control(epd) usb_endpoint_xfer_int(epd) usb_endpoint_xfer_isoc(epd) In some cases, introducing one of these functions is not possible, and it just replaces an explicit integer value by one of the following constants: USB_ENDPOINT_XFER_BULK USB_ENDPOINT_XFER_CONTROL USB_ENDPOINT_XFER_INT USB_ENDPOINT_XFER_ISOC An extract of the semantic patch that makes these changes is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r1@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bmAttributes & \(USB_ENDPOINT_XFERTYPE_MASK\|3\)) == - \(USB_ENDPOINT_XFER_CONTROL\|0\)) + usb_endpoint_xfer_control(epd) @r5@ struct usb_endpoint_descriptor *epd; @@ - ((epd->bEndpointAddress & \(USB_ENDPOINT_DIR_MASK\|0x80\)) == - \(USB_DIR_IN\|0x80\)) + usb_endpoint_dir_in(epd) @inc@ @@ #include <linux/usb.h> @depends on !inc && (r1||r5)@ @@ + #include <linux/usb.h> #include <linux/usb/...> // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-01-05Merge branch 'master' of ↵David Woodhouse
git://git.kernel.org/pub/scm/linux/kernel/git/torvalds/linux-2.6 Conflicts: arch/arm/mach-pxa/corgi.c arch/arm/mach-pxa/poodle.c arch/arm/mach-pxa/spitz.c
2008-12-23[MTD] struct device - replace bus_id with dev_name(), dev_set_name()Kay Sievers
Signed-off-by: Kay Sievers <kay.sievers@vrfy.org> Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-16[ARM] MX3: add NAND supportSascha Hauer
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
2008-12-15Merge branch 'omap3-upstream' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/tmlind/linux-omap-2.6 into devel
2008-12-10[MTD] [NAND] Set the fsl elbc ECCM according the settings in bootloader.Jason Jin
The ECCM maybe set in bootloader, Get ECCM settings from the bootloader, can avoid the image written by bootloader cannot read out by kernel. But the limitation of doing it this way is that, it could break large page NAND if it is written with NAND disabled in u-boot and read with NAND enabled, or vice versa. Signed-off-by: Jason Jin <Jason.jin@freescale.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10[MTD] [NAND] remove excess kernel-doc notationRandy Dunlap
Delete extra kernel-doc notation for struct fields and function parameters that don't exist: Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'wq' description in 'nand_chip' Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'datbuf' description in 'nand_chip' Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobbuf' description in 'nand_chip' Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'oobdirty' description in 'nand_chip' Warning(include/linux/mtd/nand.h:428): Excess struct/union/enum/typedef member 'data_poi' description in 'nand_chip' Warning(drivers/mtd/nand/nand_base.c:2527): Excess function parameter 'maxchips' description in 'nand_scan_tail' Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10Merge branch 'misc/mtd/sharpsl-nand' of ↵David Woodhouse
git://git.kernel.org/pub/scm/linux/kernel/git/lumag/tosa-2.6
2008-12-10[MTD] [NAND] Remove strange u_int64_t types from nandsimDavid Woodhouse
Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10[MTD] update internal API to support 64-bit device sizeAdrian Hunter
MTD internal API presently uses 32-bit values to represent device size. This patch updates them to 64-bits but leaves the external API unchanged. Extending the external API is a separate issue for several reasons. First, no one needs it at the moment. Secondly, whether the implementation is done with IOCTLs, sysfs or both is still debated. Thirdly external API changes require the internal API to be accepted first. Note that although the MTD API will be able to support 64-bit device sizes, existing drivers do not and are not required to do so, although NAND base has been updated. In general, changing from 32-bit to 64-bit values cause little or no changes to the majority of the code with the following exceptions: - printk message formats - division and modulus of 64-bit values - NAND base support - 32-bit local variables used by mtdpart and mtdconcat - naughtily assuming one structure maps to another in MEMERASE ioctl Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10MTD: nandsim: use less RAMAlexey Korolev
Nandsim consumes ~2x more RAM than the density of simulated device. It becomes critical if we need to simulate 256MB NAND and run stress tests on it. We investigated the reasons. nandsim allocates space for pages using kmalloc function. The size of LP nand page is 2112 bytes. kmalloc gets space from slab pools by chunks 2^n. So if we need to kmalloc 2112 bytes, 4096 bytes will be consumed by system. The best way to avoid this issue would be using kmem_cache allocations. AFAIK this mechanism specially designed to handle cases when arrays of allocations are used. Signed-off-by: Alexey Korolev <akorolev@infradead.org> Tested-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Acked-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10MTD: nandsim: add option to use a file to cache pagesAdrian Hunter
Add a new module parameter 'cache_file' which causes nandsim to use that file instead of memory to cache nand data. Using a file allows the simulation of NAND that is bigger than the available memory. Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-10MTD: nandsim: suppress unnecessary warningAdrian Hunter
nand_base sometimes reads only 2 bytes of a 4 byte id. It is OK. Do not print a warning in that case. Signed-off-by: Adrian Hunter <ext-adrian.hunter@nokia.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-03[MTD] [NAND] fix OOPS accessing flash operations over STM flash on PXADenis V. Lunev
STM 2Gb flash is a large-page NAND flash. Set operations accordingly. This field is dereferenced without a check in several places resulting in OOPS. Signed-off-by: Denis V. Lunev <den@openvz.org> Acked-by: Eric Miao <ymiao3@marvell.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-02Merge branch 'for-rmk' of ↵Russell King
git://git.kernel.org/pub/scm/linux/kernel/git/ycmiao/pxa-linux-2.6 into devel Conflicts: arch/arm/mach-pxa/pxa25x.c
2008-12-02[MTD] [NAND] drivers/mtd/nand/pasemi_nand.c: Add missing pci_dev_putJulia Lawall
pci_get_device increments a reference count that should be decremented using pci_dev_put. The semantic patch that finds the problem is as follows: (http://www.emn.fr/x-info/coccinelle/) // <smpl> @r exists@ local idexpression x; statement S,S1; position p1,p2,p3; expression E,E1; type T,T1; expression *ptr != NULL; @@ ( if ((x@p1 = pci_get_device(...)) == NULL) S | x@p1 = pci_get_device(...); ) ... when != pci_dev_put(...,(T)x,...) when != if (...) { <+... pci_dev_put(...,(T)x,...) ...+> } when != true x == NULL || ... when != x = E when != E = (T)x when any ( if (x == NULL || ...) S1 | if@p2 (...) { ... when != pci_dev_put(...,(T1)x,...) when != if (...) { <+... pci_dev_put(...,(T1)x,...) ...+> } when != x = E1 when != E1 = (T1)x ( return \(0\|<+...x...+>\|ptr\); | return@p3 ...; ) } ) @ script:python @ p1 << r.p1; p3 << r.p3; @@ print "* file: %s pci_get_device: %s return: %s" % (p1[0].file,p1[0].line,p3[0].line) // </smpl> Signed-off-by: Julia Lawall <julia@diku.dk> Acked-by: Olof Johansson <olof@lixom.net> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-12-02[ARM] pxa: explicit #include <mach/dma.h> in various driversEric Miao
Where 'pxa_dma_desc' and 'pxa_{request,free}_dma' are referenced. Signed-off-by: Eric Miao <eric.miao@marvell.com>
2008-11-29Merge branch 's3c-moves2' of git://aeryn.fluff.org.uk/bjdooks/linux into develRussell King
2008-11-27Merge branches 'core' and 'clks' into develRussell King
2008-11-27[ARM] pxa: don't pass a consumer clock name for devices with unique clocksRussell King
Where devices only have one consumer, passing a consumer clock ID has no real benefit. Remove it. Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-11-27[ARM] remove memzero()Russell King
As suggested by Andrew Morton, remove memzero() - it's not supported on other architectures so use of it is a potential build breaking bug. Since the compiler optimizes memset(x,0,n) to __memzero() perfectly well, we don't miss out on the underlying benefits of memzero(). Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk>
2008-11-27[MTD] [NAND] fsl_upm: fix build problem with 2.6.28-rc2Wolfgang Grandegger
The patch fixes following build error: CC drivers/mtd/nand/fsl_upm.o drivers/mtd/nand/fsl_upm.c: In function 'fun_chip_init': drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 2 of 'of_mtd_parse_partitions' from incompatible pointer type drivers/mtd/nand/fsl_upm.c:168: warning: passing argument 3 of 'of_mtd_parse_partitions' from incompatible pointer type drivers/mtd/nand/fsl_upm.c:168: error: too many arguments to function 'of_mtd_parse_partitions' make[1]: *** [drivers/mtd/nand/fsl_upm.o] Error 1 The breakage was introduced in 69fd3a8d098faf41a04930afa83757c0555ee360 ("[MTD] remove unused mtd parameter in of_mtd_parse_partitions()"). While at it, also add a check for the of_mtd_parse_partitions() return value. Signed-off-by: Wolfgang Grandegger <wg@grandegger.com> Signed-off-by: Anton Vorontsov <avorontsov@ru.mvista.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-07 00:32:37 +0000