summaryrefslogtreecommitdiff
path: root/drivers/mtd/chips/jedec_probe.c
AgeCommit message (Collapse)Author
2018-04-06Merge tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD updates from Boris Brezillon: "MTD Core: - Remove support for asynchronous erase (not implemented by any of the existing drivers anyway) - Remove Cyrille from the list of SPI NOR and MTD maintainers - Fix kernel doc headers - Allow users to define the partitions parsers they want to test through a DT property (compatible of the partitions subnode) - Remove the bfin-async-flash driver (the only architecture using it has been removed) - Fix pagetest test - Add extra checks in mtd_erase() - Simplify the MTD partition creation logic and get rid of mtd_add_device_partitions() MTD Drivers: - Add endianness information to the physmap DT binding - Add Eon EN29LV400A IDs to JEDEC probe logic - Use %*ph where appropriate SPI NOR Drivers: - Make fsl-quaspi assign different names to MTD devices connected to the same QSPI controller - Remove an unneeded driver.bus assigned in the fsl-qspi driver NAND Core: - Prepare arrival of the SPI NAND subsystem by implementing a generic (interface-agnostic) layer to ease manipulation of NAND devices - Move onenand code base to the drivers/mtd/nand/ dir - Rework timing mode selection - Provide a generic way for NAND chip drivers to flag a specific GET/SET FEATURE operation as supported/unsupported - Stop embedding ONFI/JEDEC param page in nand_chip NAND Drivers: - Rework/cleanup of the mxc driver - Various cleanups in the vf610 driver - Migrate the fsmc and vf610 to ->exec_op() - Get rid of the pxa driver (replaced by marvell_nand) - Support ->setup_data_interface() in the GPMI driver - Fix probe error path in several drivers - Remove support for unused hw_syndrome mode in sunxi_nand - Various minor improvements" * tag 'mtd/for-4.17' of git://git.infradead.org/linux-mtd: (89 commits) dt-bindings: fsl-quadspi: Add the example of two SPI NOR mtd: fsl-quadspi: Distinguish the mtd device names mtd: nand: Fix some function description mismatches in core.c mtd: fsl-quadspi: Remove unneeded driver.bus assignment mtd: rawnand: marvell: Rename ->ecc_clk into ->core_clk mtd: rawnand: s3c2410: enhance the probe function error path mtd: rawnand: tango: fix probe function error path mtd: rawnand: sh_flctl: fix the probe function error path mtd: rawnand: omap2: fix the probe function error path mtd: rawnand: mxc: fix probe function error path mtd: rawnand: denali: fix probe function error path mtd: rawnand: davinci: fix probe function error path mtd: rawnand: cafe: fix probe function error path mtd: rawnand: brcmnand: fix probe function error path mtd: rawnand: sunxi: Stop supporting ECC_HW_SYNDROME mode mtd: rawnand: marvell: Fix clock resource by adding a register clock mtd: ftl: Use DIV_ROUND_UP() mtd: Fix some function description mismatches in mtdcore.c mtd: physmap_of: update struct map_info's swap as per map requirement dt-bindings: mtd-physmap: Add endianness supports ...
2018-03-29mtd: jedec_probe: Fix crash in jedec_read_mfr()Linus Walleij
It turns out that the loop where we read manufacturer jedec_read_mfd() can under some circumstances get a CFI_MFR_CONTINUATION repeatedly, making the loop go over all banks and eventually hit the end of the map and crash because of an access violation: Unable to handle kernel paging request at virtual address c4980000 pgd = (ptrval) [c4980000] *pgd=03808811, *pte=00000000, *ppte=00000000 Internal error: Oops: 7 [#1] PREEMPT ARM CPU: 0 PID: 1 Comm: swapper Not tainted 4.16.0-rc1+ #150 Hardware name: Gemini (Device Tree) PC is at jedec_probe_chip+0x6ec/0xcd0 LR is at 0x4 pc : [<c03a2bf4>] lr : [<00000004>] psr: 60000013 sp : c382dd18 ip : 0000ffff fp : 00000000 r10: c0626388 r9 : 00020000 r8 : c0626340 r7 : 00000000 r6 : 00000001 r5 : c3a71afc r4 : c382dd70 r3 : 00000001 r2 : c4900000 r1 : 00000002 r0 : 00080000 Flags: nZCv IRQs on FIQs on Mode SVC_32 ISA ARM Segment none Control: 0000397f Table: 00004000 DAC: 00000053 Process swapper (pid: 1, stack limit = 0x(ptrval)) Fix this by breaking the loop with a return 0 if the offset exceeds the map size. Fixes: 5c9c11e1c47c ("[MTD] [NOR] Add support for flash chips with ID in bank other than 0") Cc: <stable@vger.kernel.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2018-03-29mtd: jedec_probe: add Eon EN29LV400A IDsLinus Walleij
This adds the JEDEC IDs for Eon EN29LV400A variants EN29LV400AB and EN29LV400AT. This chip is found in the D-Link DNS-313. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
2013-08-05mtd: jedec_probe: fix LH28F640BF definitionAndrea Adami
Zaurus 5500 contains 2 LH28F640BFHE-PTTL90 (64M 4Mx16) and the LH28F640BFHE-PTTL90.pdf datasheet available on the net shows the exact erasesize and the OTP support. At the moment only jedec_probe can discover the chip and the NOR is mounted read only probably because of wrong vpp. Signed-off-by: Andrea Adami <andrea.adami@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@linux.intel.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2011-09-11mtd: replace DEBUG() with pr_debug()Brian Norris
Start moving away from the MTD_DEBUG_LEVEL messages. The dynamic debugging feature is a generic kernel feature that provides more flexibility. (See Documentation/dynamic-debug-howto.txt) Also fix some punctuation, indentation, and capitalization that went along with the affected lines. Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <artem.bityutskiy@intel.com>
2011-09-11mtd: spelling, capitalization, uniformityBrian Norris
Therefor -> Therefore [Intern], [Internal] -> [INTERN] [REPLACABLE] -> [REPLACEABLE] syndrom, syndom -> syndrome ecc -> ECC buswith -> buswidth endianess -> endianness dont -> don't occures -> occurs independend -> independent wihin -> within erease -> erase blockes -> blocks ... Signed-off-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-11mtd: jedec_probe: initialise make sector erase command variableAntony Pavlov
In the commit 08968041bef437ec363623cd3218c2b083537ada (mtd: cfi_cmdset_0002: make sector erase command variable) introdused a field sector_erase_cmd. In the same commit initialisation of cfi->sector_erase_cmd made in cfi_chip_setup() (file drivers/mtd/chips/cfi_probe.c), so the CFI chip has no problem: ... cfi->cfi_mode = CFI_MODE_CFI; cfi->sector_erase_cmd = CMD(0x30); ... But for the JEDEC chips this initialisation is not carried out, so the JEDEC chips have sector_erase_cmd == 0. This patch adds the missing initialisation. Signed-off-by: Antony Pavlov <antony@niisi.msk.ru> Acked-by: Guillaume LECERF <glecerf@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> CC: stable@kernel.org
2011-03-11mtd: jedec_probe: Change variable name from cfi_p to cfiAntony Pavlov
In the following commit, we'll need to use the CMD() macro in order to fix the initialisation of the sector_erase_cmd field. That requires the local variable to be called 'cfi', so change it first in a simple patch. Signed-off-by: Antony Pavlov <antony@niisi.msk.ru> Acked-by: Guillaume LECERF <glecerf@gmail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com> CC: stable@kernel.org
2010-05-14mtd: chips: add SST39WF160x NOR-flashesWolfram Sang
Due to a broken CFI, they have to be added to jedec_probe. Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: jedec_probe: remove spaces before tabsArtem Bityutskiy
Nothing very important, this just makes git am stop producing warnings. Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-05-14mtd: chips: use common manufacturer codes in jedec_probe()Wolfram Sang
Factor out old manufacturers and use the generic ones from cfi.h Signed-off-by: Wolfram Sang <w.sang@pengutronix.de> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2010-02-09tree-wide: Assorted spelling fixesDaniel Mack
In particular, several occurances of funny versions of 'success', 'unknown', 'therefore', 'acknowledge', 'argument', 'achieve', 'address', 'beginning', 'desirable', 'separate' and 'necessary' are fixed. Signed-off-by: Daniel Mack <daniel@caiaq.de> Cc: Joe Perches <joe@perches.com> Cc: Junio C Hamano <gitster@pobox.com> Signed-off-by: Jiri Kosina <jkosina@suse.cz>
2009-11-30mtd: fix M29W800D dev_id and uaddrLadislav Michl
This one sits in my tree for more than two years... Using device code found on page 12 (http://www.btdesigner.com/pdfs/M29W800D.pdf) and unlock address from page 15 MTD subsytem happily detects ST M29W800DB in 16-bit mode. I do believe original author used only 8-bit mode and thus didn't hit this bug. Signed-off-by: Ladislav Michl <ladis@linux-mips.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-23mtd: jedec_probe: add PSD4256G6V idMike Frysinger
Signed-off-by: Mike Frysinger <vapier@gentoo.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-19mtd: jedec: fix compilation problem with I28F640C3B definitionStefan Roese
Signed-off-by: Stefan Roese <sr@denx.de> Signed-off-by: Vitaly Bordug <vitb@kernel.crashing.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-09-19mtd: jedec_probe: fix NEC uPD29F064115 detectionHiroshi Ito
linux v2.6.31-rc6 can not detect NEC uPD29F064115. uPD29F064115 is a 16 bit device. datasheet: http://www.cn.necel.com/memory/cn/download/M16062EJ2V0DS00.pdf This applies the same fix as used for SST chips in commit ca6f12c67ed19718cf37d0f531af9438de85b70c ("jedec_probe: Fix SST 16-bit chip detection"). Signed-off-by: Hiroshi Ito <ito@mlb.co.jp> Cc: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-06-05mtd: add SST39SF040 chip to jedec_probeMichał Mirosław
Add SST39SF040 chip (like SST39SF020A but bigger - 4Mbit). Signed-off-by: Michał Mirosław <mirq-linux@rere.qmqm.pl> Signed-off-by: Artem Bityutskiy <Artem.Bityutskiy@nokia.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2009-03-20[MTD] [CHIPS] Add JEDEC probe support for the SST 39VF3201 flash chipYegor Yefremov
Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-11-05[MTD] [NOR] Fix cfi_send_gen_cmd handling of x16 devices in x8 mode (v4)Eric W. Biederman
For "unlock" cycles to 16bit devices in 8bit compatibility mode we need to use the byte addresses 0xaaa and 0x555. These effectively match the word address 0x555 and 0x2aa, except the latter has its low bit set. Most chips don't care about the value of the 'A-1' pin in x8 mode, but some -- like the ST M29W320D -- do. So we need to be careful to set it where appropriate. cfi_send_gen_cmd is only ever passed addresses where the low byte is 0x00, 0x55 or 0xaa. Of those, only addresses ending 0xaa are affected by this patch, by masking in the extra low bit when the device is known to be in compatibility mode. [dwmw2: Do it only when (cmd_ofs & 0xff) == 0xaa] v4: Fix stupid typo in cfi_build_cmd_addr that failed to compile I'm writing this patch way to late at night. v3: Bring all of the work back into cfi_build_cmd_addr including calling of map_bankwidth(map) and cfi_interleave(cfi) So every caller doesn't need to. v2: Only modified the address if we our device_type is larger than our bus width. Cc: stable@kernel.org Signed-off-by: Eric W. Biederman <ebiederm@xmission.com> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-31[MTD] [NOR] drivers/mtd/chips/jedec_probe.c: fix Am29DL800BB device IDJerry Hicks
The device id for Am29DL800BB in jedec_probe.c is wrong. Reference: http://www.spansion.com/datasheets/21519c4.pdf I discovered this while working with u-boot. The u-boot folks mentioned Linux as an upstream reference, thought I'd post a heads-up here too. Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-07-25[MTD] jedec_probe: Fix SST 16-bit chip detectionAtsushi Nemoto
The unlock_addr rework in kernel 2.6.25 breaks 16-bit SST chips. SST 39LF160 and SST 39VF1601 are both 16-bit only chip (do not have BYTE# pin) and new uaddr value is not correct for them. Add MTD_UADDR_0xAAAA_0x5555 for those chips. Tested with SST 39VF1601 chip. Signed-off-by: Atsushi Nemoto <anemo@mba.ocn.ne.jp> Signed-off-by: David Woodhouse <David.Woodhouse@intel.com>
2008-06-04MTD/JFFS2: remove CVS keywordsAdrian Bunk
Once upon a time, the MTD repository was using CVS. This patch therefore removes all usages of the no longer updated CVS keywords from the MTD code. This also includes code that printed them to the user. Signed-off-by: Adrian Bunk <bunk@kernel.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-06-04[MTD] [NOR] Add support for Eon EN29SL800B[BT] NOR flash chipsMike Rapoport
This patch add support for non-CFI Eon EN29SL800B[BT] NOR flash chips. The Eon chips have manufacturer ID in the first bank, therefore this patch depends on support for flash chips with ID in bank other than 0. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-06-04[MTD] [NOR] Add support for flash chips with ID in bank other than 0Mike Rapoport
According to JEDEC "Standard Manufacturer's Identification Code" (http://www.jedec.org/download/search/jep106W.pdf) several first banks of NOR flash can contain 0x7f instead of actual ID. This patch adds support for reading manufacturer ID from banks other than 0. Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-06-04[MTD] [NOR] Add support for AMD AM29SL800D[BT] NOR flash chipsMike Rapoport
Signed-off-by: Mike Rapoport <mike@compulab.co.il> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-05-14[MTD] [NOR] Support for M50FLW080A and M50FLW080BNate Case
Add support for M50FLW080A and M50FLW080B revisions of LPC flash devices. Signed-off-by: Aaron Lindner <alindner@xes-inc.com> Signed-off-by: Nate Case <ncase@xes-inc.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22[MTD] [NOR] Add JEDEC support for the SST 36VF3203 flash chipAndrei Dolnikov
Add support for the SST 36VF3203 flash chip. It is used on Emerson KSI8560 board. Signed-off-by: Andrei Dolnikov <adolnikov@ru.mvista.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22[MTD] [JEDEC] Fix whitespace noise in chip tableDavid Woodhouse
Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-04-22[MTD] [JEDEC] add support for the ST M29W400DB flash chipGordon Farquharson
Add support for the ST M29W400DB flash chip. which is used on the GLAN Tank NAS. Signed-off-by: Gordon Farquharson <gordonfarquharson@gmail.com> Cc: Thomas Gleixner <tglx@linutronix.de> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-02-03[MTD] jedec probe: drop unnecessary forward declarationsIlpo Järvinen
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2008-02-03[MTD] JEDEC probe: kill some inline bloatIlpo Järvinen
$ codiff $OBJ.old $OBJ drivers/mtd/chips/jedec_probe.c: cfi_jedec_setup | -320 jedec_probe_chip | -7073 2 functions changed, 7393 bytes removed, diff: -7393 drivers/mtd/chips/jedec_probe.c: jedec_reset | +1151 1 function changed, 1151 bytes added, diff: +1151 drivers/mtd/chips/jedec_probe.o: 3 functions changed, 1151 bytes added, 7393 bytes removed, diff: -6242 Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@helsinki.fi> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-12-03[MTD] [NOR] Attempt to clean up the JEDEC unlock address confusionDavid Woodhouse
Use a single unlock address, adjust it for the device type in the knowledge that it'll be adjusted back again. This has the desirable effect of masking out the least significant bit of the address for x16 devices. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-12-03[MTD] [NOR] Fix overflow check in jedec_probeDavid Woodhouse
Having laid the code out so that it's easier to read instead of sticking to the 80-column guideline even when it doesn't make sense, a bug is immediately spotted... we were only checking _one_ of the unlock addresses to see if it runs off the end of the map. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-12-03[MTD] [NOR] Clean up jedec_probe, remove unlock address arraysDavid Woodhouse
This should have no functional effects -- we've been ignoring all but the first address in the array for a long time, and using it only to indicate which device types are supported. Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-11-09[MTD] [NOR] Add support for the SST 39VF1601 flash chipDavid Howells
Add support for the SST 39VF1601 flash chip. Signed-off-by: David Howells <dhowells@redhat.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-07-23[MTD] Clean up duplicate includes in drivers/mtd/Jesper Juhl
This patch cleans up duplicate includes in drivers/mtd/ Signed-off-by: Jesper Juhl <jesper.juhl@gmail.com> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2007-07-05[MTD] [NOR] add FUJITSU MBM29F800BA and ST M29F800AB descriptionsPhilippe De Muyter
Add descriptions for Fujitsu MBM29F800BA and ST M29F800AB flash chips. Those chips are compatible (except for the ids) with the AMD AM29F800BB. Signed-off-by: Philippe De Muyter <phdm@macqel.be> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-10-21[MTD] JEDEC probe: fix comment typo (devic)Alexey Dobriyan
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-10-21[MTD] CHIPS: Support for SST 49LF040B flash chipRyan Jackson
Add chip driver and JEDEC probe support for the SST 49LF040B flash chip. Signed-off-by: Ryan Jackson <rjackson@lnxi.com> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: David Woodhouse <dwmw2@infradead.org>
2006-08-14[PATCH] MTD: Add Macronix MX29F040 to JEDECTakashi YOSHI
Signed-off-by: Takashi YOSHII <takasi-y@ops.dti.ne.jp> Signed-off-by: Josh Boyer <jwboyer@gmail.com>
2006-06-30Remove obsolete #include <linux/config.h>Jörn Engel
Signed-off-by: Jörn Engel <joern@wohnheim.fh-wedel.de> Signed-off-by: Adrian Bunk <bunk@stusta.de>
2006-03-31[PATCH] Add chip used in collie to jedec_probePavel Machek
This adds flash chip used in Sharp Zaurus sl5500 (collie) to jedec_probe. Values work for read-only access, but I have not figured out how to do read-write. Signed-off-by: Pavel Machek <pavel@suse.cz> Cc: Richard Purdie <rpurdie@rpsys.net> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2006-03-31[PATCH] drivers/mtd: Use ARRAY_SIZE macroTobias Klauser
Use ARRAY_SIZE macro instead of sizeof(x)/sizeof(x[0]) and remove duplicates of the macro. Signed-off-by: Tobias Klauser <tklauser@nuerscht.ch> Cc: Thomas Gleixner <tglx@linutronix.de> Acked-by: David Woodhouse <dwmw2@infradead.org> Signed-off-by: Andrew Morton <akpm@osdl.org> Signed-off-by: Linus Torvalds <torvalds@osdl.org>
2005-11-07[MTD] chips: Clean up trailing white spacesThomas Gleixner
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-05-23[MTD] Add SST 39VF1601 (MPF+) IDBen Dooks
Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-05-23[MTD] Fixup probing logic for single 16bit devicesBen Dooks
The change to the generic probe to look for the smallest width of chip first is causing some problems on boards with a single 16bit device. The problem seems to be the jedec_match() is truncating the device-id read from the table to match against the one read from the hardware, causing a match against the partial id of some chips with 16bit IDs (such as the SST39LF160) This fixes things for my own board, but something may need to be done if the same problem is exhibited for chips with an 8bit ID Signed-off-by: Ben Dooks <ben@simtec.co.uk> Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2005-04-16Linux-2.6.12-rc2Linus Torvalds
Initial git repository build. I'm not bothering with the full history, even though we have it. We can create a separate "historical" git archive of that later if we want to, and in the meantime it's about 3.2GB when imported into git - space that would just make the early git days unnecessarily complicated, when we don't have a lot of good infrastructure for it. Let it rip!
generated by cgit v1.2.3 (git 2.25.1) at 2024-11-29 21:10:01 +0000