| Age | Commit message (Collapse) | Author |
|---|
|
Add support for the GL9750 and GL9755 chipsets.
Enable v4 mode and wait 5ms after set 1.8V signal enable for GL9750/
GL9755. Fix the value of SDHCI_MAX_CURRENT register and use the vendor
tuning flow for GL9750.
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The SDHCI controller on Tegra186 supports 40-bit addressing, which is
usually enough to address all of system memory. However, if the SDHCI
controller is behind an IOMMU, the address space can go beyond. This
happens on Tegra186 and later where the ARM SMMU has an input address
space of 48 bits. If the DMA API is backed by this ARM SMMU, the top-
down IOVA allocator will cause IOV addresses to be returned that the
SDHCI controller cannot access.
Unfortunately, prior to the introduction of the ->set_dma_mask() host
operation, the SDHCI core would set either a 64-bit DMA mask if the
controller claimed to support 64-bit addressing, or a 32-bit DMA mask
otherwise.
Since the full 64 bits cannot be addressed on Tegra, this had to be
worked around in commit 68481a7e1c84 ("mmc: tegra: Mark 64 bit dma
broken on Tegra186") by setting the SDHCI_QUIRK2_BROKEN_64_BIT_DMA
quirk, which effectively restricts the DMA mask to 32 bits.
One disadvantage of this is that dma_map_*() APIs will now try to use
the swiotlb to bounce DMA to addresses beyond of the controller's DMA
mask. This in turn caused degraded performance and can lead to
situations where the swiotlb buffer is exhausted, which in turn leads
to DMA transfers to fail.
With the recent introduction of the ->set_dma_mask() host operation,
this can now be properly fixed. For each generation of Tegra, the exact
supported DMA mask can be configured. This kills two birds with one
stone: it avoids the use of bounce buffers because system memory never
exceeds the addressable memory range of the SDHCI controllers on these
devices, and at the same time when an IOMMU is involved, it prevents
IOV addresses from being allocated beyond the addressible range of the
controllers.
Since the DMA mask is now properly handled, the 64-bit DMA quirk can be
removed.
Signed-off-by: Nicolin Chen <nicoleotsuka@gmail.com>
[treding@nvidia.com: provide more background in commit message]
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add host operation ->set_dma_mask() so that drivers can define their own
DMA masks.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Tested-by: Nicolin Chen <nicoleotsuka@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
Cc: stable@vger.kernel.org # v4.15 +
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We must not unconditionally set the DMA snoop bit; if the DMA API is
assuming that the device is not DMA coherent, and the device snoops the
CPU caches, the device can see stale cache lines brought in by
speculative prefetch.
This leads to the device seeing stale data, potentially resulting in
corrupted data transfers. Commonly, this results in a descriptor fetch
error such as:
mmc0: ADMA error
mmc0: sdhci: ============ SDHCI REGISTER DUMP ===========
mmc0: sdhci: Sys addr: 0x00000000 | Version: 0x00002202
mmc0: sdhci: Blk size: 0x00000008 | Blk cnt: 0x00000001
mmc0: sdhci: Argument: 0x00000000 | Trn mode: 0x00000013
mmc0: sdhci: Present: 0x01f50008 | Host ctl: 0x00000038
mmc0: sdhci: Power: 0x00000003 | Blk gap: 0x00000000
mmc0: sdhci: Wake-up: 0x00000000 | Clock: 0x000040d8
mmc0: sdhci: Timeout: 0x00000003 | Int stat: 0x00000001
mmc0: sdhci: Int enab: 0x037f108f | Sig enab: 0x037f108b
mmc0: sdhci: ACmd stat: 0x00000000 | Slot int: 0x00002202
mmc0: sdhci: Caps: 0x35fa0000 | Caps_1: 0x0000af00
mmc0: sdhci: Cmd: 0x0000333a | Max curr: 0x00000000
mmc0: sdhci: Resp[0]: 0x00000920 | Resp[1]: 0x001d8a33
mmc0: sdhci: Resp[2]: 0x325b5900 | Resp[3]: 0x3f400e00
mmc0: sdhci: Host ctl2: 0x00000000
mmc0: sdhci: ADMA Err: 0x00000009 | ADMA Ptr: 0x000000236d43820c
mmc0: sdhci: ============================================
mmc0: error -5 whilst initialising SD card
but can lead to other errors, and potentially direct the SDHCI
controller to read/write data to other memory locations (e.g. if a valid
descriptor is visible to the device in a stale cache line.)
Fix this by ensuring that the DMA snoop bit corresponds with the
behaviour of the DMA API. Since the driver currently only supports DT,
use of_dma_is_coherent(). Note that device_get_dma_attr() can not be
used as that risks re-introducing this bug if/when the driver is
converted to ACPI.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
ADMA errors are potentially data corrupting events; although we print
the register state, we do not usefully print the ADMA descriptors.
Worse than that, we print them by referencing their virtual address
which is meaningless when the register state gives us the DMA address
of the failing descriptor.
Print the ADMA descriptors giving their DMA addresses rather than their
virtual addresses, and print them using SDHCI_DUMP() rather than DBG().
We also do not show the correct value of the interrupt status register;
the register dump shows the current value, after we have cleared the
pending interrupts we are going to service. What is more useful is to
print the interrupts that _were_ pending at the time the ADMA error was
encountered. Fix that too.
Signed-off-by: Russell King <rmk+kernel@armlinux.org.uk>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Pull dma-mapping updates from Christoph Hellwig:
- add dma-mapping and block layer helpers to take care of IOMMU merging
for mmc plus subsequent fixups (Yoshihiro Shimoda)
- rework handling of the pgprot bits for remapping (me)
- take care of the dma direct infrastructure for swiotlb-xen (me)
- improve the dma noncoherent remapping infrastructure (me)
- better defaults for ->mmap, ->get_sgtable and ->get_required_mask
(me)
- cleanup mmaping of coherent DMA allocations (me)
- various misc cleanups (Andy Shevchenko, me)
* tag 'dma-mapping-5.4' of git://git.infradead.org/users/hch/dma-mapping: (41 commits)
mmc: renesas_sdhi_internal_dmac: Add MMC_CAP2_MERGE_CAPABLE
mmc: queue: Fix bigger segments usage
arm64: use asm-generic/dma-mapping.h
swiotlb-xen: merge xen_unmap_single into xen_swiotlb_unmap_page
swiotlb-xen: simplify cache maintainance
swiotlb-xen: use the same foreign page check everywhere
swiotlb-xen: remove xen_swiotlb_dma_mmap and xen_swiotlb_dma_get_sgtable
xen: remove the exports for xen_{create,destroy}_contiguous_region
xen/arm: remove xen_dma_ops
xen/arm: simplify dma_cache_maint
xen/arm: use dev_is_dma_coherent
xen/arm: consolidate page-coherent.h
xen/arm: use dma-noncoherent.h calls for xen-swiotlb cache maintainance
arm: remove wrappers for the generic dma remap helpers
dma-mapping: introduce a dma_common_find_pages helper
dma-mapping: always use VM_DMA_COHERENT for generic DMA remap
vmalloc: lift the arm flag for coherent mappings to common code
dma-mapping: provide a better default ->get_required_mask
dma-mapping: remove the dma_declare_coherent_memory export
remoteproc: don't allow modular build
...
|
|
|
|
Accessing the device when it may be runtime suspended is a bug, which is
the case in tmio_mmc_host_remove(). Let's fix the behaviour.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
The tmio_mmc_host_probe() calls pm_runtime_set_active() to update the
runtime PM status of the device, as to make it reflect the current status
of the HW. This works fine for most cases, but unfortunate not for all.
Especially, there is a generic problem when the device has a genpd attached
and that genpd have the ->start|stop() callbacks assigned.
More precisely, if the driver calls pm_runtime_set_active() during
->probe(), genpd does not get to invoke the ->start() callback for it,
which means the HW isn't really fully powered on. Furthermore, in the next
phase, when the device becomes runtime suspended, genpd will invoke the
->stop() callback for it, potentially leading to usage count imbalance
problems, depending on what's implemented behind the callbacks of course.
To fix this problem, convert to call pm_runtime_get_sync() from
tmio_mmc_host_probe() rather than pm_runtime_set_active(). Additionally, to
avoid bumping usage counters and unnecessary re-initializing the HW the
first time the tmio driver's ->runtime_resume() callback is called,
introduce a state flag to keeping track of this.
Cc: stable@vger.kernel.org
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
This reverts commit 7ff213193310ef8d0ee5f04f79d791210787ac2c.
It turns out that the above commit introduces other problems. For example,
calling pm_runtime_set_active() must not be done prior calling
pm_runtime_enable() as that makes it fail. This leads to additional
problems, such as clock enables being wrongly balanced.
Rather than fixing the problem on top, let's start over by doing a revert.
Fixes: 7ff213193310 ("mmc: tmio: move runtime PM enablement to the driver implementations")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Geert Uytterhoeven <geert@linux-m68k.org>
|
|
Since this host controller can merge bigger segments if DMA API
layer cam merge the segments, this patch adds the flag.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
|
|
Don't populate the array degrees on the stack but instead make it
static const. Makes the object code smaller by 46 bytes.
Before:
text data bss dec hex filename
5356 1560 0 6916 1b04 dw_mmc-hi3798cv200.o
After:
text data bss dec hex filename
5214 1656 0 6870 1ad6 dw_mmc-hi3798cv200.o
(gcc version 9.2.1, amd64)
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Instead of keeping track of whether SDIO IRQs have been enabled via an
internal sdhci status flag, avoid the open-coding and convert into using
sdio_irq_claimed().
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Nowadays sdhci prevents runtime suspend when SDIO IRQs are enabled.
However, some variants such as sdhci-esdhc-imx's, tries to allow runtime
suspend while having the SDIO IRQs enabled, but without supporting remote
wakeups. This support is a bit questionable, especially if the host device
have a PM domain attached that can be power gated, but more importantly,
the code have also become redundant (which was not the case when it was
introduced).
Rather than keeping the redundant code around, let's drop it and leave this
to be revisited later on.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sdhci_ack_sdio_irq() is called only when SDIO IRQs are enabled.
Therefore, let's drop the redundant check of the internal
SDHCI_SDIO_IRQ_ENABLED flag and just re-enable the IRQs immediately.
Reviewed-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means msdc_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the mtk-sd
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the mtk-sd driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the mtk-sd driver, so let's do that.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In cases when SDIO IRQs have been enabled, runtime suspend is prevented by
the driver. However, this still means dw_mci_runtime_suspend|resume() gets
called during system suspend/resume, via pm_runtime_force_suspend|resume().
This means during system suspend/resume, the register context of the dw_mmc
device most likely loses its register context, even in cases when SDIO IRQs
have been enabled.
To re-enable the SDIO IRQs during system resume, the dw_mmc driver
currently relies on the mmc core to re-enable the SDIO IRQs when it resumes
the SDIO card, but this isn't the recommended solution. Instead, it's
better to deal with this locally in the dw_mmc driver, so let's do that.
Tested-by: Matthias Kaehlcke <mka@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
|
|
Fix data read/write error in HS200 mode due to chip DLL lock phase shift
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
shift issue
Move functions in preparation to fix DLL lock phase shift issue
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Change O2 Host PLL and DLL register name
Signed-off-by: Shirley Her <shirley.her@bayhubtech.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
When switching from any MMC speed mode that requires 1.8v
(HS200, HS400 and HS400ES) to High Speed (HS) mode, the system
ends up configured for SDR12 with a 50MHz clock which is an illegal
mode.
This happens because the SDHCI_CTRL_VDD_180 bit in the
SDHCI_HOST_CONTROL2 register is left set and when this bit is
set, the speed mode is controlled by the SDHCI_CTRL_UHS field
in the SDHCI_HOST_CONTROL2 register. The SDHCI_CTRL_UHS field
will end up being set to 0 (SDR12) by sdhci_set_uhs_signaling()
because there is no UHS mode being set.
The fix is to change sdhci_set_uhs_signaling() to set the
SDHCI_CTRL_UHS field to SDR25 (which is the same as HS) for
any switch to HS mode.
This was found on a new eMMC controller that does strict checking
of the speed mode and the corresponding clock rate. It caused the
switch to HS400 mode to fail because part of the sequence to switch
to HS400 requires a switch from HS200 to HS before going to HS400.
Suggested-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Al Cooper <alcooperx@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Resolves the following build error reported by the 0-day bot:
ERROR: "of_platform_device_create" [drivers/mmc/host/sdhci-of-aspeed.ko] undefined!
SPARC does not set CONFIG_OF_ADDRESS so the symbol is missing. Depend on
CONFIG_OF_ADDRESS to ensure the driver is only built for supported
configurations.
Fixes: 2d28dbe042f4 ("mmc: sdhci-of-aspeed: Add support for the ASPEED SD controller")
Reported-by: kbuild test robot <lkp@intel.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a get_max_clock() handler to sdhci-of-aspeed to report f_max as the
maximum clock rate if it is set. This enables artificial limitation of
the bus speed via max-frequency in the devicetree for e.g. the AST2600
evaluation board where I was seeing errors at 200MHz.
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The early-exit didn't seem to matter on the AST2500, but on the AST2600
the SD clock genuinely may not be running on entry to
aspeed_sdhci_set_clock(). Remove the early exit to ensure we always run
sdhci_enable_clk().
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
host->clock is already managed by sdhci_set_ios().
Suggested-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Use for_each_sg() macro instead of open coded variant.
No functional change intended.
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Save set clock in mmc_host actual_clock enabling exporting it via debugfs.
This will indicate the precise SD clock in I/O settings rather than only the
sometimes misleading requested clock.
Signed-off-by: Tamás Szűcs <tszucs@protonmail.ch>
Reviewed-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently, the DMA addresses are casted to (u64) for the upper 32bits
to avoid "right shift count >= width of type" warning.
<linux/kernel.h> provides macros to address this, and I like the macro
names are self-documenting.
I introduced a new helper, sdhci_set_adma_addr() to avoid the code
duplication.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The datasheet of the IP (sd4hc) says it is compiatible with SDHCI v4,
but the spec version field in the version register is read as 2
(i.e. SDHCI_SPEC_300) based on the RTL provided by Cadence.
Socionext did not fix it up when it integrated the IP into the SoCs.
So, it is working as SDHCI v3.
It is not a real problem because there is no difference in the program
flow in sdhci.c between SDHCI_SPEC_300/400, but set the real version
just in case.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
__sdhci_read_caps() does not modify *ver, *caps, or *caps1.
Probably, the caller of this function will want to constifythe
parameters passed in.
Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
SDIO IRQ is not defaultly triggered by low level,
but by falling edge. It needs to set related register
to enable SDIO IRQ low level trigger function.
Otherwise the SDIO IRQ may be lost in some specail condition.
Signed-off-by: Yong Mao <yong.mao@mediatek.com>
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Export sdhci_abort_tuning() function symbols which are used by other SD Host
controller driver modules.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The GL9750 and GL9755 chipsets, and possibly others, require PLL Enable
setup as part of the internal clock setup as described in 3.2.1 Internal
Clock Setup Sequence of SD Host Controller Simplified Specification
Version 4.20.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
According to section 3.2.1 internal clock setup in SD Host Controller
Simplified Specifications 4.20, the timeout of loop for checking
internal clock stable is defined as 150ms.
Signed-off-by: Ben Chuang <ben.chuang@genesyslogic.com.tw>
Co-developed-by: Michael K Johnson <johnsonm@danlj.org>
Signed-off-by: Michael K Johnson <johnsonm@danlj.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current arasan sdhci PHY configuration isn't compatible
with the PHY on Intel's LGM(Lightning Mountain) SoC devices.
Therefore, add a new compatible, to adapt the Intel's LGM
eMMC PHY with arasan-sdhc controller to configure the PHY.
Signed-off-by: Ramuthevar Vadivel Muruganx <vadivel.muruganx.ramuthevar@linux.intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In case of error, the function of_platform_device_create() returns
NULL pointer not ERR_PTR(). The IS_ERR() test in the return value
check should be replaced with NULL test.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Reviewed-by: Andrew Jeffery <andrew@aj.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make sure the sdhost driver doesn't use requests bigger than SWIOTLB
can handle.
Signed-off-by: Stefan Wahren <wahrenst@gmx.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add a minimal driver for ASPEED's SD controller, which exposes two
SDHCIs.
The ASPEED design implements a common register set for the SDHCIs, and
moves some of the standard configuration elements out to this common
area (e.g. 8-bit mode, and card detect configuration which is not
currently supported).
The SD controller has a dedicated hardware interrupt that is shared
between the slots. The common register set exposes information on which
slot triggered the interrupt; early revisions of the patch introduced an
irqchip for the register, but reality is it doesn't behave as an
irqchip, and the result fits awkwardly into the irqchip APIs. Instead
I've taken the simple approach of using the IRQ as a shared IRQ with
some minor performance impact for the second slot.
Ryan was the original author of the patch - I've taken his work and
massaged it to drop the irqchip support and rework the devicetree
integration. The driver has been smoke tested under qemu against a
minimal SD controller model and lightly tested on an ast2500-evb.
Signed-off-by: Ryan Chen <ryanchen.aspeed@gmail.com>
Signed-off-by: Andrew Jeffery <andrew@aj.id.au>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Reviewed-by: Joel Stanley <joel@jms.id.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
MSDC IP which support 64G DRAM will support 24bits BDMA buffer length,
so add support it.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
when plug out SD card, may get data CRC error, the MMC core will issue
CMD13 to get card status, then CMD13 timeout(due to card plug out) will
trigger CMD19 tuning, first CMD19 timeout has not call msdc_reset_hw()
and cause the next CMD19 gets controller busy.
Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
All R-Car Gen3 SoCs with any ES version cannot use this DMAC actually.
So, this patch removes the compatibles of R-Car Gen3 SoCs from
renesas_sdhi_sys_dmac_of_match. Since the previous code has
an empty whitelist to prevent probing of R-Car Gen3 SoCs,
no behavior changes.
Signed-off-by: Yoshihiro Shimoda <yoshihiro.shimoda.uh@renesas.com>
Reviewed-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Tested-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We don't need to set the 'slave_id' anymore - that field is never read
by the DMA driver.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Fix wrong code indentation which made the code hard to read, and fix
return with value in void function.
Signed-off-by: Paul Cercueil <paul@crapouillou.net>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
One of the more common cases of allocation size calculations is finding
the size of a structure that has a zero-sized array at the end, along
with memory for some number of elements for that array. For example:
struct sdhci_cdns_priv {
...
struct sdhci_cdns_phy_param phy_params[0];
};
Make use of the struct_size() helper instead of an open-coded version
in order to avoid any potential type mistakes.
So, replace the following form:
sizeof(*priv) + sizeof(priv->phy_params[0]) * nr_phy_params
with:
struct_size(priv, phy_params, nr_phy_params)
Also, notice that, in this case, variable priv_size is not necessary,
hence it is removed.
This code was detected with the help of Coccinelle.
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch is to add erratum A011334 support in ls1028a 1.0 SoC
Signed-off-by: Yinbo Zhu <yinbo.zhu@nxp.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Cc: linux-mmc@vger.kernel.org
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Add another PCI Id for Intel CML.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/sdhci-s3c.c: In function 'sdhci_s3c_probe':
drivers/mmc/host/sdhci-s3c.c:613:19: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->mmc->caps |= MMC_CAP_8_BIT_DATA;
drivers/mmc/host/sdhci-s3c.c:614:2: note: here
case 4:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mmc/host/atmel-mci.c: In function 'atmci_get_cap':
drivers/mmc/host/atmel-mci.c:2415:30: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_odd_clk_div = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2416:2: note: here
case 0x400:
^~~~
drivers/mmc/host/atmel-mci.c:2422:28: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.has_highspeed = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2423:2: note: here
case 0x200:
^~~~
drivers/mmc/host/atmel-mci.c:2426:40: warning: this statement may fall through [-Wimplicit-fallthrough=]
host->caps.need_notbusy_for_read_ops = 1;
~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~^~~
drivers/mmc/host/atmel-mci.c:2427:2: note: here
case 0x100:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Kees Cook <keescook@chromium.org>
Acked-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
