| Age | Commit message (Collapse) | Author |
|---|
|
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It's unlikely that this is really needed on any single-slot systems
where we disable card detects until the end of probe, but it still
seems safer to check to make sure that a slot has been initted before
we try to dereference it to find the SDIO interrupt mask.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We really don't want to get a card detect interrupt during probe time
since it can confuse things. Let's disable the card detect interrupt
until we're in a really good place: the end of probe. Let's also
simply avoid enabling the card detect interrupt if it's not used.
It appears that (at least on rk3288) when vqmmc is turned on it can
cause a bogus "card detect" interrupt. That meant that we were
getting a predictable card detect interrupt while we were in
mmc_add_host(). On the version of the kernel I'm working with at
least (3.14), this is not a great time to get a card detect interrupt
since I think that we don't grab all the needed locks in
mmc_add_host() and children. I put stack dumps in dw_mci_setup_bus()
and found that I could see two distinct stack crawls that looked like:
Caller one:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_power_up
* mmc_start_host
* mmc_add_host
Caller two:
* dw_mci_setup_bus
* dw_mci_set_ios
* mmc_set_chip_select
* mmc_go_idle
* mmc_rescan
* process_one_work
* worker_thread
* kthread
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We've seen problems on some WiFi modules where we seem to send a CMD53
(which requires the data lines) while the module is asserting busy.
We shouldn't do that.
The Designware Databook says that before issuing a new data transfer
command we should check for busy, so that's what we'll do.
We'll leverage the existing dw_mmc knowledge about whether it should
wait for the previous command to finish to know whether we should
check for busy before sending the command. This means we won't end up
incorrectly waiting for things like CMD52 (SDIO) or CMD13 (SD) which
don't use the data line.
Note that this also has the advantage of making sure that we don't
change the clock while the card is busy, too.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We should give dw_mmc a good reset after we apply power. On some
boards vqmmc may actually be connected to the IP block in the SoC so
it's good to reset after power comes in.
Without this we sometimes see failures enumerating cards on rk3288.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It appears that we can confuse things if we try to turn on the MMC
clock when the power is off. Adjust is so that we turn the clock on
(using dw_mci_setup_bus) after power is all the way on and we turn the
clock off before the power goes off.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The STOP command can terminate a data transfer between a memory card and
mmc controller.
As show in Synopsys DesignWare Cores Mobile Storage Host Databook:
Data timeout and Data end-bit error will terminate further data transfer
by mmc controller. So we should not send abort command to terminate a
data transfer again if we got DRTO and EBE interrupt.
After this patch, all mmc_test cases can pass on RK3288-Pink2 board.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Implements HS400 mode support for exynos host driver.
This also include some updates as new mode is added.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
[Alim: addressed review comments]
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If we power up vqmmc in MMC_POWER_ON then we end up turning it on
before mmc_power_up() sets the signal voltage. That's not so great
since we might be powering it up at the wrong voltage.
Note that this is how Yuvaraj originally coded things up in
<https://patchwork.kernel.org/patch/4401231/> but he changed it on my
suggestion. Apparently I was wrong.
Reported-by: Alexandru M Stan <amstan@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Instead of having a local hack taking care of sending the tuning
command and as well to verify the response pattern, let's convert to
the common mmc_send_tuning() API.
This change affects the Exynos variant, since it's the only one which
support the dw_mmc's ->execute_tuning() callback.
It's seems like dw_mmc internal logic expects failed data transfers to
be ended using a stop command. Let the tuning requests also fall into
this category, since there are data transfer involved.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
|
|
This patch remove unnecessary 'out of memory' message on dw mmc driver.
Signed-off-by: Beomho Seo <beomho.seo@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Even though 1MB is reserved for descriptor table in IDMAC,
the dw_mmc host driver is allowed to receive only maximum
128KB block length in one request. This is caused by setting
improper max_blk_count. It needs to be e adjusted so that
descriptor table is used fully. It is found that the performance
is improved with the increased the max_blk_count.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We're running into cases where our enabling of the SDIO interrupt in
dw_mmc doesn't actually take effect. Specifically, adding patch like
this:
+++ b/drivers/mmc/host/dw_mmc.c
@@ -1076,6 +1076,9 @@ static void dw_mci_enable_sdio_irq(struct mmc_host *mmc, int enb)
mci_writel(host, INTMASK,
(int_mask | SDMMC_INT_SDIO(slot->id)));
+ int_mask = mci_readl(host, INTMASK);
+ if (!(int_mask & SDMMC_INT_SDIO(slot->id)))
+ dev_err(&mmc->class_dev, "failed to enable sdio irq\n");
} else {
...actually triggers the error message. That's because the
dw_mci_enable_sdio_irq() unsafely does a read-modify-write of the
INTMASK register.
We can't just use the standard host->lock since that lock is not irq
safe and mmc_signal_sdio_irq() (called from interrupt context) calls
dw_mci_enable_sdio_irq(). Add a new irq-safe lock to protect INTMASK.
An alternate solution to this is to punt mmc_signal_sdio_irq() to the
tasklet and then protect INTMASK modifications by the standard host
lock. This seemed like a bit more of a high-latency change.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: James Hogan <james.hogan@imgtec.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In the patch (9623b5b mmc: dw_mmc: Disable low power mode if SDIO
interrupts are used) I added code that disabled the low power mode of
dw_mmc when SDIO interrupts are used. That code worked but always
felt a little hacky because we ended up disabling low power as a side
effect of the first enable_sdio_irq() call. That wouldn't be so bad
except that disabling low power involves a complicated process of
writing to the CMD/CMDARG registers and that extra process makes it
difficult to cleanly the read-modify-write race in
dw_mci_enable_sdio_irq() (see future patch in the series).
Change the code to take advantage of the init_card() callback of the
mmc core to do this right at bootup.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Commit f1d2736c8156 (mmc: dw_mmc: control card read threshold) added
dw_mci_ctrl_rd_thld() with an unconditional write to the CDTHRCTL
register at offset 0x100. However before version 240a, the FIFO region
started at 0x100, so the write messes with the FIFO and completely
breaks the driver.
If the version id < 240A, return early from dw_mci_ctl_rd_thld() so as
not to hit this problem.
Fixes: f1d2736c8156 (mmc: dw_mmc: control card read threshold)
Signed-off-by: James Hogan <james.hogan@imgtec.com>
Cc: <stable@vger.kernel.org> # v3.13+
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The bit of sdio interrupt is 16 in designware implementation,
but it is 24 on Rockchip SoCs.This patch add sdio_id0 for the
number of slot0 in the SDIO interrupt registers.
Signed-off-by: Addy Ke <addy.ke@rock-chips.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Synopsys DW_MMC IP core supports Internal DMA Controller with 64-bit address mode from IP version 2.70a onwards.
Updated the driver to support IDMAC 64-bit addressing mode.
Signed-off-by: Prabu Thangamuthu <prabu.t@synopsys.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The dw_mmc driver had a bunch of code that ran whenever a card was
ejected and inserted. However, this code was old and crufty and
should be removed. Some evidence that it's really not needed:
1. Is is supposed to be legal to use 'cd-gpio' on dw_mmc instead of
using the built-in card detect mechanism. The 'cd-gpio' code
doesn't run any of the crufty old code but yet still works.
2. While looking at this, I realized that my old change (369ac86 mmc:
dw_mmc: don't queue up a card detect at slot startup) actually
castrated the old code a little bit already and nobody noticed.
Specifically "last_detect_state" was left as 0 at bootup. That
means that on the first card removal none of the crufty code ran.
3. I can run "while true; do dd if=/dev/mmcblk1 of=/dev/null; done"
while ejecting and inserting an SD Card and the world doesn't
explode.
If some of the crufty old code is actually needed, we should justify
it and also put it in some place where it will be run even with
"cd-gpio".
Note that in my case I'm using the "cd-gpio" mechanism but for various
reasons the hardware triggers a dw_mmc "card detect" at bootup. That
was actually causing a real bug. The card detect workqueue was
running while the system was trying to enumerate the card. The
"present != slot->last_detect_state" triggered and we were doing all
kinds of crazy stuff and messing up enumeration. The new mechanism of
just asking the core to check the card is much safer and then the
bogus interrupt doesn't hurt.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: alim.akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In (28f92b5 mmc: core: Try other signal levels during power up) we can
see that there are times when it's valid to try several signal
voltages. Don't print an ugly error in the logs when that happens.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We've already got a reset of DMA after it's done. Add one before we
start DMA too. This fixes a data corruption on Rockchip SoCs which
will get bad data when doing a DMA transfer after doing a PIO transfer.
We tested this on an Exynos 5800 with HS200 and didn't notice any
difference in sequential read throughput.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Jaehoon Chung <jh80.chung@samsung.com>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The same tuning block exists in the dw_mmc h.c and sdhci-msm.c
files. Move these into mmc.c so that they can be shared across
drivers.
Reported-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
dw_mci_of_find_slot_node() is only used in dw_mci_of_get_slot_quirks()
if CONFIG_OF is defined, thus there is no need to have a !CONFIG_OF
version of it. Fixes the following compile warning with !CONFIG_OF:
CC [M] drivers/mmc/host/dw_mmc.o
drivers/mmc/host/dw_mmc.c:2223:28: warning: ‘dw_mci_of_find_slot_node’ defined but not used [-Wunused-function]
Signed-off-by: Tobias Klauser <tklauser@distanz.ch>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It's possible that mmc_of_parse() could return errors (possibly in
some future version it might return -EPROBE_DEFER even). Let's pass
those errors back.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For UHS cards we need the ability to switch voltages from 3.3V to
1.8V. Add support to the dw_mmc driver to handle this. Note that
dw_mmc needs a little bit of extra code since the interface needs a
special bit programmed to the CMD register while CMD11 is progressing.
This means adding a few extra states to the state machine to track.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch makes use of mmc_regulator_get_supply() to handle
the vmmc and vqmmc regulators.Also it moves the code handling
the these regulators to dw_mci_set_ios().It turned on the vmmc
and vqmmc during MMC_POWER_UP and MMC_POWER_ON,and turned off
during MMC_POWER_OFF.
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If we happened to get a data error at just the wrong time the dw_mmc
driver could get into a state where it would never complete its
request. That would leave the caller just hanging there.
We fix this two ways and both of the two fixes on their own appear to
fix the problems we've seen:
1. Fix a race in the tasklet where the interrupt setting the data
error happens _just after_ we check for it, then we get a
EVENT_XFER_COMPLETE. We fix this by repeating a bit of code.
2. Fix it so that if we detect that we've got an error in the "data
busy" state and we're not going to do anything else we end the
request and unblock anyone waiting.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@gmail.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Slot quirks "disable-wp" is deprecated.
Instead, use the host quirk "disable-wp".
(Because the slot-node is removed in dt-file.)
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Tested-by: Sachin Kamat <sachin.kamat@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Reviewed-by: Doug Anderson <dianders@chromium.org>
Tested-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch changes the fifo reset code to follow the reset procedure
outlined in the documentation of Synopsys Mobile storage host databook.
Signed-off-by: Sonny Rao <sonnyrao@chromium.org>
Signed-off-by: Yuvaraj Kumar C D <yuvaraj.cd@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
[sonnyrao: fix compile for !CONFIG_MMC_DW_IDMAC case]
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Data errors are completely expected during tuning. Printing them out
is confusing people looking at the kernel logs. They see things like:
[ 3.613296] dwmmc_exynos 12200000.dwmmc0: data error, status 0x00000088
...and they think something is wrong with their hardware.
Remove the printouts. We'll leave it up to a higher level to report
about errors.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Restore the card-present checking point.
(The following part was removed from commit bf626e5 ("mmc: dw_mmc:
use slot-gpio to handle cd pin")
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
If mmc_of_parse() is used, dw_mci_of_get_cd_gpio/wp_gpio didn't need.
Already implemented into mmc_of_parse().
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Remove unnecessary function. This function didn't re-use anywhere.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Fixed an indentation block.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Since using the device-tree, didn't use the callback pointer.
So removed the unused callback pointer.
When the set_power callback is used, it should be added in future.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
It's right to check immediately whether host->bus_hz is assigned or not.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
mmc_of_parse() have been already parsed the general capability.
Didn't need to use the local parser.
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Replaced UHS_DDR50 with MMC_DDR52. And MMC_CAP_UHS_DDR50
is removed because of non-implementation of UHS signaling.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc
Pull MMC updates from Chris Ball:
"MMC highlights for 3.15:
Core:
- CONFIG_MMC_UNSAFE_RESUME=y is now default behavior
- DT bindings for SDHCI UHS, eMMC HS200, high-speed DDR, at 1.8/1.2V
- Add GPIO descriptor based slot-gpio card detect API
Drivers:
- dw_mmc: Refactor SOCFPGA support as a variant inside dw_mmc-pltfm.c
- mmci: Support HW busy detection on ux500
- omap: Support MMC_ERASE
- omap_hsmmc: Support MMC_PM_KEEP_POWER, MMC_PM_WAKE_SDIO_IRQ, (a)cmd23
- rtsx: Support pre-req/post-req async
- sdhci: Add support for Realtek RTS5250 controllers
- sdhci-acpi: Add support for 80860F16, fix 80860F14/SDIO card detect
- sdhci-msm: Add new driver for Qualcomm SDHCI chipset support
- sdhci-pxav3: Add support for Marvell Armada 380 and 385 SoCs"
* tag 'mmc-updates-for-3.15-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (102 commits)
mmc: sdhci-acpi: Intel SDIO has broken card detect
mmc: sdhci-pxav3: add support for the Armada 38x SDHCI controller
mmc: sdhci-msm: Add platform_execute_tuning implementation
mmc: sdhci-msm: Initial support for Qualcomm chipsets
mmc: sdhci-msm: Qualcomm SDHCI binding documentation
sdhci: only reprogram retuning timer when flag is set
mmc: rename ARCH_BCM to ARCH_BCM_MOBILE
mmc: sdhci: Allow for irq being shared
mmc: sdhci-acpi: Add device id 80860F16
mmc: sdhci-acpi: Fix broken card detect for ACPI HID 80860F14
mmc: slot-gpio: Add GPIO descriptor based CD GPIO API
mmc: slot-gpio: Split out CD IRQ request into a separate function
mmc: slot-gpio: Record GPIO descriptors instead of GPIO numbers
Revert "dts: socfpga: Add support for SD/MMC on the SOCFPGA platform"
mmc: sdhci-spear: use generic card detection gpio support
mmc: sdhci-spear: remove support for power gpio
mmc: sdhci-spear: simplify resource handling
mmc: sdhci-spear: fix platform_data usage
mmc: sdhci-spear: fix error handling paths for DT
mmc: sdhci-bcm-kona: fix build errors when built-in
...
|
|
Tejun Heo has made WQ_NON_REENTRANT useless in the dbf2576e37
("workqueue: make all workqueues non-reentrant"). So remove its
usages and definition.
This patch doesn't introduce any behavior changes.
tj: minor description updates.
Signed-off-by: ZhangZhen <zhenzhang.zhang@huawei.com>
Sigend-off-by: Tejun Heo <tj@kernel.org>
Acked-by: James Chapman <jchapman@katalix.com>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
If mrq->sbc is not NULL but data->stop happens to be NULL,
it will lead to NULL pointer dereferencing. Avoid this by
having a NULL check for data->stop.
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
bf626e5550f24aec ("mmc: dw_mmc: use slot-gpio to handle cd pin") caused
CDETECT to be ignored, since negated return value of mmc_gpio_get_cd(mmc)
can not be checked by IS_ERR_VALUE.
Also, add spin_lock_bh(&host->lock) for atomic access to
DW_MMC_CARD_PRESENT, otherwise sd detect may occasionally fail.
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Reported-by: Kevin Hilman <khilman@linaro.org>
Reviewed-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Sachin Kamat <sachin.kamat@linaro.org>
Tested-by: Kevin Hilman <khilman@linaro.org>
Acked-by: Seungwon Jeon <tgih.jun@samsung.com>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Suggested by Jaehoon: Use slot-gpio to handle cd-gpio
Add function dw_mci_of_get_cd_gpio to check "cd-gpios" from dts.
mmc_gpio_request_cd and mmc_gpio_get_cd are used to handle cd pin
Signed-off-by: Zhangfei Gao <zhangfei.gao@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Chris Ball <chris@printf.net>
|
|
Suspend and resume of cards are being handled from the protocol layer
and consequently the mmc_suspend|resume_host APIs are deprecated.
This means we can simplify the suspend|resume callbacks by removing the
use of the deprecated APIs.
Cc: Seungwon Jeon <tgih.jun@samsung.com>
Cc: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In IDMAC mode EVENT_XFER_COMPLETE is set when RI/TI of last descriptor
is done. So if errors are happened in the middle of data transfers,
'dw_mci_stop_dma' during error handing can be called and eventually
prevents this flag to be set. This results in permanent wait for
EVENT_XFER_COMPLETE in 'dw_mci_tasklet_func'. Therefore, if dma
running is stopped forcibly, EVENT_XFER_COMPLETE should be set.
Reported-by: Bing Zhao <bzhao@marvell.com>
Signed-off-by: Doug Anderson <dianders@chromium.org>
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
First, compiling warning along with previous change is removed.
[drivers/mmc/host/dw_mmc.c:1890:7: warning: unused variable 'ctrl']
And with the recommendation in manual, IDMAC software reset is followed
by dma-reset of the CTRL register in order to terminate the transfer.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
There are three resets in CTRL register. FIFO reset is especially used
in several points with the same routine. It could be replaced with one
function and the others may be applied similarly if needed. So,
mci_wait_reset() is modified to allow various bit field of reset.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Main change corresponds to dw_mci_command_complete(). And EBE is
divided into read and write. Some minor changes for code readability.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
In error cases, DTO interrupt may or may not be generated depending
on remained data. Stop/Abort command ensures DTO generation for that
situation. Currently if 'stop' field of data is empty, there is no
stop/abort command. So, it could hang waiting DTO. This change
reinforces these cases.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Even if response error is detected in case data command, data transfer
is continued. It means that data can live in FIFO. Current handling
just breaks out the request when seeing the command error. This causes
kernel panic in dw_mci_read_data_pio() [host->data = NULL]. And also,
FIFO should be guaranteed to be empty.
Unable to handle kernel NULL pointer dereference at virtual address 00000018
<...>
[<c02af814>] (dw_mci_read_data_pio+0x68/0x198) from [<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0)
[<c02b04b4>] (dw_mci_interrupt+0x374/0x3a0) from [<c006b094>] (handle_irq_event_percpu+0x50/0x194)
[<c006b094>] (handle_irq_event_percpu+0x50/0x194) from [<c006b214>] (handle_irq_event+0x3c/0x5c)
[<c006b214>] (handle_irq_event+0x3c/0x5c) from [<c006de1c>] (handle_fasteoi_irq+0xa4/0x148)
[<c006de1c>] (handle_fasteoi_irq+0xa4/0x148) from [<c006aa88>] (generic_handle_irq+0x20/0x30)
[<c006aa88>] (generic_handle_irq+0x20/0x30) from [<c000f154>] (handle_IRQ+0x38/0x90)
[<c000f154>] (handle_IRQ+0x38/0x90) from [<c00085bc>] (gic_handle_irq+0x34/0x68)
[<c00085bc>] (gic_handle_irq+0x34/0x68) from [<c0011f40>] (__irq_svc+0x40/0x70)
Exception stack(0xef0b1c00 to 0xef0b1c48)
1c00: 000eb0cf ffffffff 00001300 c01a7738 ef295e10 0000000a c04df298 ef0b1dc0
1c20: ef295ec0 00000000 00000000 00000006 00000000 ef0b1c48 c02b1274 c01a7764
1c40: 20000113 ffffffff
[<c0011f40>] (__irq_svc+0x40/0x70) from [<c01a7764>] (__loop_delay+0x0/0xc)
Code: e1a00005 e0891006 e0662004 e12fff33 (e59a3018)
---[ end trace a7043b9ba9aed1db ]---
Kernel panic - not syncing: Fatal exception in interrupt
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
|
Card Read Threshold should be ensured that the card clock does not stop
in the middle of a block of data being transferred from the card to the
Host. Specially, clock stop is allowed in fast transfer such as HS200
or SDR104 mode. And so, it should be enabled.
Signed-off-by: Seungwon Jeon <tgih.jun@samsung.com>
Tested-by: Alim Akhtar <alim.akhtar@samsung.com>
Signed-off-by: Chris Ball <cjb@laptop.org>
|
