| Age | Commit message (Collapse) | Author |
|---|
|
Allow to specify in the device-tree that no physical write-protect signal
is connected to a particular instance of a MMC controller. Setting the
property will cause the core will assume that the SD card is always
read-write.
The name for the new property is 'disable-wp' and was chosen based on the
property with the same function from the Synopsys designware mobile storage
host controller DT bindings specification.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Cc: Rob Herring <robh+dt@kernel.org>
Cc: Pawel Moll <pawel.moll@arm.com>
Cc: Mark Rutland <mark.rutland@arm.com>
Cc: Ian Campbell <ijc+devicetree@hellion.org.uk>
Cc: Kumar Gala <galak@codeaurora.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
It is not uncommon to see systems where there is no physical write-protect
signal (e.g. when using eMMC or microSD card slots). For some controllers,
which have a dedicated write-protection detection logic (like SDHCI
controllers), the get_ro() callback can return bogus data in such a case.
Instead of handling this on a per controller basis this patch adds a new
capability flag to the MMC core that can be set to specify that the result
of get_ro() is invalid. When the flag is set the core will not call
get_ro() and assume that the card is always read-write.
Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Check the error code for EOPNOTSUPP and do not print
reset warning in that case.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
CRC errors could possibly be alleviated by
re-tuning so flag re-tuning needed in those cases.
Note this has no effect if re-tuning has not been
enabled.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
HS400 re-tuning must be done in HS200 mode. Add
the ability to switch from HS400 mode to HS200
mode before re-tuning and switch back to HS400
after re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Make a separate function to do the mmc_switch status check
so it can be re-used. This is preparation for adding support
for HS400 re-tuning.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The sleep command is issued after deselecting the
card, but re-tuning won't work on a deselected card
so re-tuning must be held.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during bkops to prevent
it from conflicting with the busy state.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during erase commands to prevent
it from conflicting with the sequence of commands.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Hold re-tuning during switch commands to prevent
it from conflicting with the busy state or the CMD13
verification.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
At the start of each request, re-tune if needed and
then hold off re-tuning again until the request is done.
Note that though there is one function that starts
requests (mmc_start_request) there are two that wait for
the request to be done (mmc_wait_for_req_done and
mmc_wait_for_data_req_done). Also note that
mmc_wait_for_data_req_done can return even when the
request is not done (which allows the block driver
to prepare a newly arrived request while still
waiting for the previous request).
This patch ensures re-tuning is held for the duration
of a request. Subsequent patches will also hold
re-tuning at other times when it might cause a
conflict.
In addition, possibly a command is failing because
re-tuning is needed. Use mmc_retune_recheck() to check
re-tuning. At that point re-tuning is held, at least by
the request, so mmc_retune_recheck() flags host->retune_now
if the hold count is 1.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enable re-tuning when tuning is executed and
disable re-tuning when card is no longer initialized.
In the case of SDIO suspend, the card can keep power.
In that case, re-tuning need not be disabled, but, if
a re-tuning timer is being used, ensure it is disabled
and assume that re-tuning will be needed upon resume
since it is not known how long the suspend will last.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently, there is core support for tuning during
initialization. There can also be a need to re-tune
periodically (e.g. sdhci) or to re-tune after the
host controller is powered off (e.g. after PM
runtime suspend / resume) or to re-tune in response
to CRC errors.
The main requirements for re-tuning are:
- ability to enable / disable re-tuning
- ability to flag that re-tuning is needed
- ability to re-tune before any request
- ability to hold off re-tuning if the card is busy
- ability to hold off re-tuning if re-tuning is in
progress
- ability to run a re-tuning timer
To support those requirements 7 members are added to struct
mmc_host:
unsigned int can_retune:1; /* re-tuning can be used */
unsigned int doing_retune:1; /* re-tuning in progress */
unsigned int retune_now:1; /* do re-tuning at next req */
int need_retune; /* re-tuning is needed */
int hold_retune; /* hold off re-tuning */
unsigned int retune_period; /* re-tuning period in secs */
struct timer_list retune_timer; /* for periodic re-tuning */
need_retune is an integer so it can be set without needing
synchronization. hold_retune is a integer to allow nesting.
Various simple functions are provided to set / clear those
variables.
Subsequent patches take those functions into use.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Some drivers schedule automatic hw resets. An example is mwifiex,
which schedules a card reset if the command handler between driver
and card firmware becomes out of sync
Signed-off-by: Andreas Fenkart <afenkart@gmail.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The PM_RESTORE_PREPARE is not handled now in mmc_pm_notify(),
as result mmc_rescan() could be scheduled and executed at
late hibernation restore stages when MMC device is suspended
already - which, in turn, will lead to system crash on TI dra7-evm board:
WARNING: CPU: 0 PID: 3188 at drivers/bus/omap_l3_noc.c:148 l3_interrupt_handler+0x258/0x374()
44000000.ocp:L3 Custom Error: MASTER MPU TARGET L4_PER1_P3 (Idle): Data Access in User mode during Functional access
Hence, add missed PM_RESTORE_PREPARE PM event in mmc_pm_notify().
Fixes: 4c2ef25fe0b8 (mmc: fix all hangs related to mmc/sd card...)
Signed-off-by: Grygorii Strashko <Grygorii.Strashko@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This reverts commit 6685ac62b2f0 ("mmc: core: Convert mmc_driver to
device_driver")
The reverted commit went too far in simplifing the device driver parts
for mmc.
Let's restore the old mmc_driver to enable driver core to sooner
or later to remove the ->probe(), ->remove() and ->shutdown() callbacks
from the struct device_driver.
Note that, the old ->suspend|resume() callbacks in the struct
mmc_driver don't need to be restored, since the mmc block layer has
converted to the modern system PM ops.
Fixes: 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver")
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
If the struct mmc_pwrseq_match .alloc function used to allocate a
struct mmc_pwrseq fails, the error is propagated to mmc_of_parse().
But instead of returning the error code in pwrseq, host->pwrseq is
returned which will always be 0. So mmc_of_parse() succeeds even if
the pwrseq .alloc function failed and host->pwrseq is NULL.
This makes the SDIO device to not be powered if the power sequencing
.alloc functions wants to be deferred due a missing resource because
the mmc controller driver probe did wrongly succeed.
Fixes: 0f12a0ce4ce4a ("mmc: pwrseq: simplify alloc/free hooks")
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial
Pull trivial tree from Jiri Kosina:
"Usual trivial tree updates. Nothing outstanding -- mostly printk()
and comment fixes and unused identifier removals"
* 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/jikos/trivial:
goldfish: goldfish_tty_probe() is not using 'i' any more
powerpc: Fix comment in smu.h
qla2xxx: Fix printks in ql_log message
lib: correct link to the original source for div64_u64
si2168, tda10071, m88ds3103: Fix firmware wording
usb: storage: Fix printk in isd200_log_config()
qla2xxx: Fix printk in qla25xx_setup_mode
init/main: fix reset_device comment
ipwireless: missing assignment
goldfish: remove unreachable line of code
coredump: Fix do_coredump() comment
stacktrace.h: remove duplicate declaration task_struct
smpboot.h: Remove unused function prototype
treewide: Fix typo in printk messages
treewide: Fix typo in printk messages
mod_devicetable: fix comment for match_flags
|
|
The eMMC on a tablet I've will stop working / communicating as soon as
the kernel executes:
mmc_switch(card, EXT_CSD_CMD_SET_NORMAL,
EXT_CSD_HPI_MGMT, 1,
card->ext_csd.generic_cmd6_time);
There seems to be no way to reliable identify eMMC-s which have a broken
hpi implementation, but at least for eMMC's which are soldered onto a board
we can work around this by specifying that hpi is broken in devicetree.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Currently those host drivers which have deployed runtime PM, deals with
the runtime PM reference counting entirely by themselves.
Since host drivers don't know when the core will send the next request
through some of the host_ops callbacks, they need to handle runtime PM
get/put between each an every request.
In quite many cases this has some negative effects, since it leads to a
high frequency of scheduled runtime PM suspend operations. That due to
the runtime PM reference count will normally reach zero in-between
every request.
We can decrease that frequency, by enabling the core to deal with
runtime PM reference counting of the host device. Since the core often
knows that it will send a seqeunce of requests, it makes sense for it
to keep a runtime PM reference count during these periods.
More exactly, let's increase the runtime PM reference count by invoking
pm_runtime_get_sync() from __mmc_claim_host(). Restore that action by
invoking pm_runtime_mark_last_busy() and pm_runtime_put_autosuspend()
in mmc_release_host(). In this way a runtime PM reference count will be
kept during the complete cycle of a claim -> release host.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
Acked-by: Konstantin Dorfman <kdorfman@codeaurora.org>
|
|
These callbacks have been set to deprecated for some time. The last
user (omap_hsmmc) has moved away from using them, which thus enables
us to completely remove them.
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Every call to sdio_enable_4bit_bus is followed (on success) by a call
to mmc_set_bus_width().
To simplify the code, include those calls directly in
sdio_enable_4bit_bus().
Signed-off-by: NeilBrown <neil@brown.name>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The alloc() and free() hooks required each pwrseq implementation to set
host->pwrseq themselves. This is error-prone and could be done at a
higher level if alloc() was changed to return a pointer to a struct
mmc_pwrseq instead of an error code.
This patch performs this change and moves the burden of maintaining
host->pwrseq from the power sequence hooks to the pwrseq code.
Signed-off-by: Alexandre Courbot <acourbot@nvidia.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The current error-path code (when gpiod_get_index() reports
an error) can never free pwrseq->reset_gpios[0], but might
try to tree pwrseq->reset_gpios[-1], which has unfortunate
consequences.
Signed-off-by: NeilBrown <neil@brown.name>
Fixes: 934f1f48330ed695927a51fa068dc5d673f2da19
Acked-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reported-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
|
|
This patch fix spelling typo in printk messages.
Signed-off-by: Masanari Iida <standby24x7@gmail.com>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
|
|
This patch provides a simple mmc-pwrseq-emmc driver, which controls
single gpio line. It perform standard eMMC hw reset procedure, as
descibed by Jedec 4.4 specification. This procedure is performed just
after MMC core enabled power to the given mmc host (to fix possible
issues if bootloader has left eMMC card in initialized or unknown
state), and before performing complete system reboot (also in case of
emergency reboot call). The latter is needed on boards, which doesn't
have hardware reset logic connected to emmc card and (limited or broken)
ROM bootloaders are unable to read second stage from the emmc card if
the card is left in unknown or already initialized state.
Signed-off-by: Marek Szyprowski <m.szyprowski@samsung.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Host drivers have different ways to sends their "init stream" to the
card. Some need to do it as part of a request, some do it from the
->set_ios() callback in the MMC_POWER_ON state and some don't send an
"init stream" at all.
To be able to use the reset GPIOs from the simple MMC power sequence
provider, the card need to be powered and the "init stream" must not
have been sent.
To cope with these requirements, invoke mmc_pwrseq_post_power_on()
prior we change the state to MMC_POWER_ON in mmc_power_up().
Host drivers shall perform power up operations in the MMC_POWER_UP
state. Unfortunate three hosts (au1xmmc, cb710-mmc and toshsd) don't
conform to this expectation. Instead those ignore the MMC_POWER_UP
state and delays their power up operations to the MMC_POWER_ON state.
Those hosts needs to change their behavior to enable proper support for
the simple MMC power sequence provider.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
Some WLAN chips attached to a SDIO interface, need a reference clock.
Since this is very common, extend the prseq_simple driver to support
an optional clock that is enabled prior the card power up procedure.
Note: the external clock is optional. Thus an error is not returned
if the clock is not found.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Many WLAN attached to a SDIO/MMC interface, needs more than one pin for
their reset sequence. For example, is very common for chips to have two
pins: one for reset and one for power enable.
This patch adds support for more reset pins to the pwrseq_simple driver
and instead hardcoding a fixed number, it uses the of_gpio_named_count()
since the MMC power sequence is only built when CONFIG_OF is enabled.
Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Signed-off-by: Srinivas Kandagatla <srinivas.kandagatla@linaro.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This patch is coming to fix compatibility issue of BKOPS_EN field of EXT_CSD.
In eMMC-5.1, BKOPS_EN was changed, and now it has two operational bits:
Bit 0 - MANUAL_EN
Bit 1 - AUTO_EN
In previous eMMC revisions, only Bit 0 was supported.
Signed-off-by: Alexey Skidanov <alexey.skidanov@sandisk.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The need for reset GPIOs has several times been pointed out from
erlier posted patchsets. Especially some WLAN chips which are
attached to an SDIO interface may use a GPIO reset.
The reset GPIO is asserted at initialization and prior we start the
power up procedure. The GPIO will be de-asserted right after the power
has been provided to the card, from the ->post_power_on() callback.
Note, the reset GPIO is optional. Thus we don't return an error even if
we can't find a GPIO for the consumer.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
To add the core part for the MMC power sequence, let's start by adding
initial support for the simple MMC power sequence provider.
In this initial step, the MMC power sequence node are fetched and the
compatible string for the simple MMC power sequence provider are
verified.
At this point we don't parse the node for any properties, but instead
that will be handled from following patches. Since there are no
properties supported yet, let's just implement the ->alloc() and the
->free() callbacks.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
System on chip designs may specify a specific MMC power sequence. To
successfully detect an (e)MMC/SD/SDIO card, that power sequence must
be followed while initializing the card.
To be able to handle these SOC specific power sequences, let's add a
MMC power sequence interface. It provides the following functions to
help the mmc core to deal with these power sequences.
mmc_pwrseq_alloc() - Invoked from mmc_of_parse(), to initialize data.
mmc_pwrseq_pre_power_on()- Invoked in the beginning of mmc_power_up().
mmc_pwrseq_post_power_on()- Invoked at the end in mmc_power_up().
mmc_pwrseq_power_off()- Invoked from mmc_power_off().
mmc_pwrseq_free() - Invoked from mmc_free_host(), to free data.
Each MMC power sequence provider will be responsible to implement a set
of callbacks. These callbacks mirrors the functions above.
This patch adds the skeleton, following patches will extend the core of
the MMC power sequence and add support for a specific simple MMC power
sequence.
Do note, since the mmc_pwrseq_alloc() is invoked from mmc_of_parse(),
host drivers needs to make use of this API to enable the support for
MMC power sequences. Moreover the MMC power sequence support depends on
CONFIG_OF.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Tested-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
Reviewed-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk>
|
|
Both callers of mmc_start_request() call mmc_card_removed()
so move that call into mmc_start_request().
This patch is preparation for adding re-tuning support.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
For each MMC, SD and SDIO there is code that
holds the clock, calls ops->execute_tuning, and
releases the clock. Simplify the code a bit by
providing a separate function to do that.
Signed-off-by: Adrian Hunter <adrian.hunter@intel.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
One of the reasons omap_hsmmc doesn't use the slot-gpio library
is that it has some non-standard functionality in the card-detect
interrupt service routine.
To make it possible for omap_hsmmc (and maybe others) to be converted
to use slot-gpio, add 'mmc_gpio_request_cd_isr' which provide an
alternate isr to be register by the slot-gpio code.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Enable power cycle and re-initialization of SD cards via the reset
bus_ops. Power cycling a buggy SD card sometimes helps it get back on
track.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Move the (e)MMC specific hw_reset code from core.c into mmc.c. Call the
code from the new bus_ops member "reset". This also allows for adding
a SD card specific reset procedure.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Always check if the card is alive after a successful reset. This allows
us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only
card reset interface.
Signed-off-by: Johan Rudholm <johanru@axis.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
This adds SDIO devicetree subnode parsing to the mmc core. While
SDIO devices are runtime probable they sometimes need nonprobable
additional information on embedded systems, like an additional gpio
interrupt or a clock. This patch makes it possible to supply this
information from the devicetree. SDIO drivers will find a pointer
to the devicenode in their devices of_node pointer.
Signed-off-by: Sascha Hauer <s.hauer@pengutronix.de>
[hdegoede@redhat.com: Misc. cleanups]
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Since previous patches removed the need for the tuning block patterns
to be exported, let's move them close to the mmc_send_tuning() API.
Those are now intended to be used only by the mmc core.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
Reviewed-by: Stephen Boyd <sboyd@codeaurora.org>
Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
|
|
By moving the allocation of the slot-gpio data into mmc_alloc_host(),
we can remove the slot-gpio internal calls to mmc_gpio_alloc().
This means mmc_gpio_alloc() has now only one caller left, which
consequence allow us to simplify and remove some of the slot-gpio code.
Additionally, this makes the slot-gpio mutex redundant, so let's remove
it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
To be consistent when freeing data, let's move the idr_remove() call
from mmc_free_host() into the ->dev_release() callback for the class
device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
As a step in moving slot-gpio functions/structs closer to the MMC core,
let's add a local header file for slot-gpio.
In this initial step we move mmc_gpio_alloc() into the header file,
to make it available for the MMC core. Following patches will show the
utilization of it.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
We had a mix of using the class device and the parent device while
allocating data through the devm_* managed functions.
Let's be more consistent and always use the parent device.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
The slot-gpio uses the devm*_ managed functions. Still it provide APIs
to explicitly free requested CD/WP GPIOs, but these API isn't being
used.
Therefore let's simplify slot-gpio by removing these unused APIs. If it
later turns out we need some of them, we can always consider to restore
the code.
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
Instead of just printing an error when mmc_of_parse() fails to request
CD/WP GPIO pins, let's propagate all errors, except for -ENOENT.
Earlier only -EPROBE_DEFER was handled correctly.
As a side effect of this change and by relying on host drivers to
handle the errors during ->probe(), we don't need to free any data in
the error path.
This also means we are actually fixing a bug, since we remove the call
to mmc_gpio_free_cd() which wasn't the correct function to invoke to
handle cleanup. Instead that should have been mmc_gpiod_free_cd().
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
In (3fcb027 ARM: MXC: mxcmmc: work around a bug in the SDHC busy line
handling) the optional init_card() callback was added. According to
the original change it was "for now only called from
mmc_sdio_init_card()".
This callback really ought to be called from the SD and MMC init
functions as well. One current user of this callback
(mxcmci_init_card) will not work as expected if you insert an SDIO
card, then eject it and put a normal SD card in. Specifically the
normal SD card will not get to run with 4-bit data.
I'd like to use the init_card() callback to handle a similar quirk on
dw_mmc when using SDIO Interrupts (the "low power" feature of the card
needs to be disabled), so that will add a second user of the function.
Signed-off-by: Doug Anderson <dianders@chromium.org>
Reviewed-by: Grant Grundler <grundler@chromium.org>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
mmc_select_bus_width() will try to switch to MMC_BUS_WIDTH_4 even if
MMC_CAP_4_BIT_DATA and MMC_CAP_8_BIT_DATA are not set in host->caps.
Return as soon as possible when those flags are not set
Fixes: 577fb13199b1 (mmc: rework selection of bus speed mode)
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: <stable@vger.kernel.org> # 3.17
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull ACPI and power management updates from Rafael Wysocki:
"This time we have some more new material than we used to have during
the last couple of development cycles.
The most important part of it to me is the introduction of a unified
interface for accessing device properties provided by platform
firmware. It works with Device Trees and ACPI in a uniform way and
drivers using it need not worry about where the properties come from
as long as the platform firmware (either DT or ACPI) makes them
available. It covers both devices and "bare" device node objects
without struct device representation as that turns out to be necessary
in some cases. This has been in the works for quite a few months (and
development cycles) and has been approved by all of the relevant
maintainers.
On top of that, some drivers are switched over to the new interface
(at25, leds-gpio, gpio_keys_polled) and some additional changes are
made to the core GPIO subsystem to allow device drivers to manipulate
GPIOs in the "canonical" way on platforms that provide GPIO
information in their ACPI tables, but don't assign names to GPIO lines
(in which case the driver needs to do that on the basis of what it
knows about the device in question). That also has been approved by
the GPIO core maintainers and the rfkill driver is now going to use
it.
Second is support for hardware P-states in the intel_pstate driver.
It uses CPUID to detect whether or not the feature is supported by the
processor in which case it will be enabled by default. However, it
can be disabled entirely from the kernel command line if necessary.
Next is support for a platform firmware interface based on ACPI
operation regions used by the PMIC (Power Management Integrated
Circuit) chips on the Intel Baytrail-T and Baytrail-T-CR platforms.
That interface is used for manipulating power resources and for
thermal management: sensor temperature reporting, trip point setting
and so on.
Also the ACPI core is now going to support the _DEP configuration
information in a limited way. Basically, _DEP it supposed to reflect
off-the-hierarchy dependencies between devices which may be very
indirect, like when AML for one device accesses locations in an
operation region handled by another device's driver (usually, the
device depended on this way is a serial bus or GPIO controller). The
support added this time is sufficient to make the ACPI battery driver
work on Asus T100A, but it is general enough to be able to cover some
other use cases in the future.
Finally, we have a new cpufreq driver for the Loongson1B processor.
In addition to the above, there are fixes and cleanups all over the
place as usual and a traditional ACPICA update to a recent upstream
release.
As far as the fixes go, the ACPI LPSS (Low-power Subsystem) driver for
Intel platforms should be able to handle power management of the DMA
engine correctly, the cpufreq-dt driver should interact with the
thermal subsystem in a better way and the ACPI backlight driver should
handle some more corner cases, among other things.
On top of the ACPICA update there are fixes for race conditions in the
ACPICA's interrupt handling code which might lead to some random and
strange looking failures on some systems.
In the cleanups department the most visible part is the series of
commits targeted at getting rid of the CONFIG_PM_RUNTIME configuration
option. That was triggered by a discussion regarding the generic
power domains code during which we realized that trying to support
certain combinations of PM config options was painful and not really
worth it, because nobody would use them in production anyway. For
this reason, we decided to make CONFIG_PM_SLEEP select
CONFIG_PM_RUNTIME and that lead to the conclusion that the latter
became redundant and CONFIG_PM could be used instead of it. The
material here makes that replacement in a major part of the tree, but
there will be at least one more batch of that in the second part of
the merge window.
Specifics:
- Support for retrieving device properties information from ACPI _DSD
device configuration objects and a unified device properties
interface for device drivers (and subsystems) on top of that. As
stated above, this works with Device Trees and ACPI and allows
device drivers to be written in a platform firmware (DT or ACPI)
agnostic way. The at25, leds-gpio and gpio_keys_polled drivers are
now going to use this new interface and the GPIO subsystem is
additionally modified to allow device drivers to assign names to
GPIO resources returned by ACPI _CRS objects (in case _DSD is not
present or does not provide the expected data). The changes in
this set are mostly from Mika Westerberg, Rafael J Wysocki, Aaron
Lu, and Darren Hart with some fixes from others (Fabio Estevam,
Geert Uytterhoeven).
- Support for Hardware Managed Performance States (HWP) as described
in Volume 3, section 14.4, of the Intel SDM in the intel_pstate
driver. CPUID is used to detect whether or not the feature is
supported by the processor. If supported, it will be enabled
automatically unless the intel_pstate=no_hwp switch is present in
the kernel command line. From Dirk Brandewie.
- New Intel Broadwell-H ID for intel_pstate (Dirk Brandewie).
- Support for firmware interface based on ACPI operation regions used
by the PMIC chips on the Intel Baytrail-T and Baytrail-T-CR
platforms for power resource control and thermal management (Aaron
Lu).
- Limited support for retrieving off-the-hierarchy dependencies
between devices from ACPI _DEP device configuration objects and
deferred probing support for the ACPI battery driver based on the
_DEP information to make that driver work on Asus T100A (Lan
Tianyu).
- New cpufreq driver for the Loongson1B processor (Kelvin Cheung).
- ACPICA update to upstream revision 20141107 which only affects
tools (Bob Moore).
- Fixes for race conditions in the ACPICA's interrupt handling code
and in the ACPI code related to system suspend and resume (Lv Zheng
and Rafael J Wysocki).
- ACPI core fix for an RCU-related issue in the ioremap() regions
management code that slowed down significantly after CPUs had been
allowed to enter idle states even if they'd had RCU callbakcs
queued and triggered some problems in certain proprietary graphics
driver (and elsewhere). The fix replaces synchronize_rcu() in that
code with synchronize_rcu_expedited() which makes the issue go
away. From Konstantin Khlebnikov.
- ACPI LPSS (Low-Power Subsystem) driver fix to handle power
management of the DMA engine included into the LPSS correctly. The
problem is that the DMA engine doesn't have ACPI PM support of its
own and it simply is turned off when the last LPSS device having
ACPI PM support goes into D3cold. To work around that, the PM
domain used by the ACPI LPSS driver is redesigned so at least one
device with ACPI PM support will be on as long as the DMA engine is
in use. From Andy Shevchenko.
- ACPI backlight driver fix to avoid using it on "Win8-compatible"
systems where it doesn't work and where it was used by default by
mistake (Aaron Lu).
- Assorted minor ACPI core fixes and cleanups from Tomasz Nowicki,
Sudeep Holla, Huang Rui, Hanjun Guo, Fabian Frederick, and Ashwin
Chaugule (mostly related to the upcoming ARM64 support).
- Intel RAPL (Running Average Power Limit) power capping driver fixes
and improvements including new processor IDs (Jacob Pan).
- Generic power domains modification to power up domains after
attaching devices to them to meet the expectations of device
drivers and bus types assuming devices to be accessible at probe
time (Ulf Hansson).
- Preliminary support for controlling device clocks from the generic
power domains core code and modifications of the ARM/shmobile
platform to use that feature (Ulf Hansson).
- Assorted minor fixes and cleanups of the generic power domains core
code (Ulf Hansson, Geert Uytterhoeven).
- Assorted minor fixes and cleanups of the device clocks control code
in the PM core (Geert Uytterhoeven, Grygorii Strashko).
- Consolidation of device power management Kconfig options by making
CONFIG_PM_SLEEP select CONFIG_PM_RUNTIME and removing the latter
which is now redundant (Rafael J Wysocki and Kevin Hilman). That
is the first batch of the changes needed for this purpose.
- Core device runtime power management support code cleanup related
to the execution of callbacks (Andrzej Hajda).
- cpuidle ARM support improvements (Lorenzo Pieralisi).
- cpuidle cleanup related to the CPUIDLE_FLAG_TIME_VALID flag and a
new MAINTAINERS entry for ARM Exynos cpuidle (Daniel Lezcano and
Bartlomiej Zolnierkiewicz).
- New cpufreq driver callback (->ready) to be executed when the
cpufreq core is ready to use a given policy object and cpufreq-dt
driver modification to use that callback for cooling device
registration (Viresh Kumar).
- cpufreq core fixes and cleanups (Viresh Kumar, Vince Hsu, James
Geboski, Tomeu Vizoso).
- Assorted fixes and cleanups in the cpufreq-pcc, intel_pstate,
cpufreq-dt, pxa2xx cpufreq drivers (Lenny Szubowicz, Ethan Zhao,
Stefan Wahren, Petr Cvek).
- OPP (Operating Performance Points) framework modification to allow
OPPs to be removed too and update of a few cpufreq drivers
(cpufreq-dt, exynos5440, imx6q, cpufreq) to remove OPPs (added
during initialization) on driver removal (Viresh Kumar).
- Hibernation core fixes and cleanups (Tina Ruchandani and Markus
Elfring).
- PM Kconfig fix related to CPU power management (Pankaj Dubey).
- cpupower tool fix (Prarit Bhargava)"
* tag 'pm+acpi-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (120 commits)
i2c-omap / PM: Drop CONFIG_PM_RUNTIME from i2c-omap.c
dmaengine / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
tools: cpupower: fix return checks for sysfs_get_idlestate_count()
drivers: sh / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
e1000e / igb / PM: Eliminate CONFIG_PM_RUNTIME
MMC / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
MFD / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
misc / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
media / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
input / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
leds: leds-gpio: Fix multiple instances registration without 'label' property
iio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hsi / OMAP / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
i2c-hid / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
drm / exynos / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
gpio / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
hwrandom / exynos / PM: Use CONFIG_PM in #ifdef
block / PM: Replace CONFIG_PM_RUNTIME with CONFIG_PM
USB / PM: Drop CONFIG_PM_RUNTIME from the USB core
PM: Merge the SET*_RUNTIME_PM_OPS() macros
...
|
