summaryrefslogtreecommitdiff
path: root/drivers/mmc/card/mmc_test.c
AgeCommit message (Collapse)Author
2016-02-29mmc: mmc_test: mention that '0' runs all testsWolfram Sang
I had to use the source to determine what I need to write to 'test' so that all tests are run. Let's mention this explicitly in 'testlist'. Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-10-21mmc: core: Fix init_card in 52MhzChaotian Jing
Suppose that we got a data crc error, and it triggers the mmc_reset. mmc_reset will call mmc_send_status to see if HW reset was supported. before issue CMD13, it will do retune, and if EMMC was in HS400 mode, it will reduce frequency to 52Mhz firstly, then results in card init was doing at 52Mhz. The mmc_send_status was originally only done for mmc_test, should drop it. And, rename the "eMMC hardware reset" to "Reset test", as we would also be able to use the test for SD-cards. Signed-off-by: Chaotian Jing <chaotian.jing@mediatek.com> Suggested-by: Adrian Hunter <adrian.hunter@intel.com> Fixes: bd11e8bd03ca ("mmc: core: Flag re-tuning is needed on CRC errors") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01mmc: mmc-test: use swap() in mmc_test_nonblock_transfer()Fabian Frederick
Use kernel.h macro definition. Signed-off-by: Fabian Frederick <fabf@skynet.be> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-06-01mmc: card: mmc_test: Simplify a trivial if-return sequenceFabio Estevam
Simplify a trivial if-return sequence. Possibly combine with a preceding function call. The semantic patch that makes this change is available in scripts/coccinelle/misc/simple_return.cocci. More information about semantic patching is available at http://coccinelle.lip6.fr/ Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2015-04-17Revert "mmc: core: Convert mmc_driver to device_driver"Ulf Hansson
This reverts commit 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver") The reverted commit went too far in simplifing the device driver parts for mmc. Let's restore the old mmc_driver to enable driver core to sooner or later to remove the ->probe(), ->remove() and ->shutdown() callbacks from the struct device_driver. Note that, the old ->suspend|resume() callbacks in the struct mmc_driver don't need to be restored, since the mmc block layer has converted to the modern system PM ops. Fixes: 6685ac62b2f0 ("mmc: core: Convert mmc_driver to device_driver") Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Acked-by: Jaehoon Chung <jh80.chung@samsung.com>
2015-01-19mmc: core: always check status after resetJohan Rudholm
Always check if the card is alive after a successful reset. This allows us to remove mmc_hw_reset_check(), leaving mmc_hw_reset() as the only card reset interface. Signed-off-by: Johan Rudholm <johanru@axis.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-10mmc: mmc_test: Extend "Badly aligned" tests for 8-byte alignmentAdrian Hunter
The "Badly aligned" tests, test reading/writing with alignments of 1,2 and 3. SDHCI now has 64-bit ADMA which has 8-byte alignment, so extend the tests to test up to 7. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2014-11-10mmc: core: Convert mmc_driver to device_driverUlf Hansson
The struct mmc_driver adds an extra layer on top of the struct device_driver. That would be fine, if there were a good reason, but that's not the case. Let's simplify code by converting to the common struct device_driver instead and thus also removing superfluous overhead. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
2013-08-24mmc: mmc_test: replace strict_strtol() with kstrtol_from_user()Jingoo Han
The usage of strict_strtol() is not preferred, because strict_strtol() is obsolete. Thus, kstrtol() should be used. Also, both kstrtol() and copy_from_user() can be replaced with kstrtol_from_user() to make the code simpler. Signed-off-by: Jingoo Han <jg1.han@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2013-06-27mmc: core: Handle card shutdown from mmc_busUlf Hansson
Considering shutdown of the card, the responsibility to initate this sequence shall be driven from the mmc_bus. This patch enables the mmc_bus to handle this sequence properly. A new .shutdown callback is added in the mmc_driver struct which is used to shutdown the blk device. Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-13Merge tag 'mmc-merge-for-3.3-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc MMC highlights for 3.3: Core: * Support for the HS200 high-speed eMMC mode. * Support SDIO 3.0 Ultra High Speed cards. * Kill pending block requests immediately if card is removed. * Enable the eMMC feature for locking boot partitions read-only until next power on, exposed via sysfs. Drivers: * Runtime PM support for Intel Medfield SDIO. * Suspend/resume support for sdhci-spear. * sh-mmcif now processes requests asynchronously. * tag 'mmc-merge-for-3.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/cjb/mmc: (58 commits) mmc: fix a deadlock between system suspend and MMC block IO mmc: sdhci: restore the enabled dma when do reset all mmc: dw_mmc: miscaculated the fifo-depth with wrong bit operation mmc: host: Adds support for eMMC 4.5 HS200 mode mmc: core: HS200 mode support for eMMC 4.5 mmc: dw_mmc: fixed wrong bit operation for SDMMC_GET_FCNT() mmc: core: Separate the timeout value for cache-ctrl mmc: sdhci-spear: Fix compilation error mmc: sdhci: Deal with failure case in sdhci_suspend_host mmc: dw_mmc: Clear the DDR mode for non-DDR mmc: sd: Fix SDR12 timing regression mmc: sdhci: Fix tuning timer incorrect setting when suspending host mmc: core: Add option to prevent eMMC sleep command mmc: omap_hsmmc: use threaded irq handler for card-detect. mmc: sdhci-pci: enable runtime PM for Medfield SDIO mmc: sdhci: Always pass clock request value zero to set_clock host op mmc: sdhci-pci: remove SDHCI_QUIRK2_OWN_CARD_DETECTION mmc: sdhci-pci: get gpio numbers from platform data mmc: sdhci-pci: add platform data mmc: sdhci: prevent card detection activity for non-removable cards ...
2012-01-11mmc: mmc_test: align max_seg_sizePer Forlin
If max_seg_size is unaligned, mmc_test_map_sg() may create sg element sizes that are not aligned with 512 byte. Fix, align max_seg_size at mmc_test_area_init(). Signed-off-by: Per Forlin <per.forlin@stericsson.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2012-01-03switch debugfs to umode_tAl Viro
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
2011-10-26mmc: replace printk with appropriate display macroGirish K S
All the files using printk function for displaying kernel messages in the mmc driver have been replaced with corresponding macro. Signed-off-by: Girish K S <girish.shivananjappa@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: Add module.h to drivers/mmc users assuming implicit presence.Paul Gortmaker
We are cleaning up the implicit presence of module.h; these guys are some of the people who just assume it will be there. Call it out explitly for those that really need it. Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-10-26mmc: mmc-test: add eMMC hardware reset testAdrian Hunter
MMC core provides a checking function that checks if the reset has happended. Add a test to use that function. Signed-off-by: Adrian Hunter <adrian.hunter@intel.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13mmc: core: use defined R1_STATE_PRG macro for card statusJaehoon Chung
Signed-off-by: Jaehoon Chung <jh80.chung@samsung.com> Signed-off-by: Kyungmin Park <kyungmin.park@samsung.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-08-13mmc: mmc_test: avoid stalled file in debugfsAndy Shevchenko
During card removal and inserting cycle the test file in the debugfs could be stalled until the host driver removes it. Let's keep the file in the linked list and destroy it when card is removed. Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com> Acked-by: Per Forlin <per.forlin@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20mmc: mmc_test: test to measure how sg_len affect performancePer Forlin
Add a test that measures how the mmc bandwidth depends on the numbers of sg elements in the sg list. The transfer size if fixed and sg length goes from a few up to 512. The purpose is to measure overhead caused by multiple sg elements. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Venkatraman S <svenkatr@ti.com> Tested-by: Sourav Poddar <sourav.poddar@ti.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20mmc: mmc_test: add test for non-blocking transfersPer Forlin
Add four tests for read and write performance per different transfer size, 4k to 4M. * Read using blocking mmc request * Read using non-blocking mmc request * Write using blocking mmc request * Write using non-blocking mmc request The host driver must support pre_req() and post_req() in order to run the non-blocking test cases. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Venkatraman S <svenkatr@ti.com> Tested-by: Sourav Poddar<sourav.poddar@ti.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-07-20mmc: mmc_test: add debugfs file to list all testsPer Forlin
Add a debugfs file "testlist" to print all available tests. Signed-off-by: Per Forlin <per.forlin@linaro.org> Acked-by: Kyungmin Park <kyungmin.park@samsung.com> Acked-by: Arnd Bergmann <arnd@arndb.de> Reviewed-by: Venkatraman S <svenkatr@ti.com> Tested-by: Sourav Poddar<sourav.poddar@ti.com> Tested-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: mmc_test: minor clean up, use t = &test.area everywhereAndy Shevchenko
Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: initialize struct mmc_request at declaration timeChris Ball
Converts from: struct mmc_request mrq; memset(&mrq, 0, sizeof(struct mmc_request)); to: struct mmc_request mrq = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: initialize struct mmc_data at declaration timeChris Ball
Converts from: struct mmc_data data; memset(&data, 0, sizeof(struct mmc_data)); to: struct mmc_data data = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
2011-05-24mmc: initialize struct mmc_command at declaration timeChris Ball
Converts from: struct mmc_command cmd; memset(&cmd, 0, sizeof(struct mmc_command)); to: struct mmc_command cmd = {0}; because it's shorter, as performant, and easier to work out whether initialization has happened. Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-31Fix common misspellingsLucas De Marchi
Fixes generated by 'codespell' and manually reviewed. Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>
2011-03-25mmc: mmc_test: Remove set-but-unused variable.Chris Ball
Fixes: drivers/mmc/card/mmc_test.c: In function ‘mmc_test_seq_perf’: drivers/mmc/card/mmc_test.c:1878:28: warning: variable ‘ts’ set but not used [-Wunused-but-set-variable] There's no reason to be calling timespec_sub() here, because mmc_test_print_avg_rate() is going to do that itself. Signed-off-by: Chris Ball <cjb@laptop.org> Cc: Adrian Hunter <adrian.hunter@nokia.com>
2011-03-15mmc: mmc_test: add tests to measure large sequential I/O performanceAdrian Hunter
Add two large sequential I/O performance tests: 35. Large sequential read into scattered pages 36. Large sequential write from scattered pages The tests measure transfer times for 10MiB, 100MiB, 1000MiB. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-15mmc: mmc_test: add tests to measure random I/O operations per secondAdrian Hunter
Existing performance tests measure single or sequential I/O speed. Add two random I/O tests: 33. Random read performance by transfer size 34. Random write performance by transfer size Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-15mmc: mmc_test: make performance test area size about 4MiBAdrian Hunter
The test area size was set to the preferred erase size but for comparison purposes it is better if it is the same size for different devices. Make it a multiple of preferred erase size that is greater than or equal to 4MiB. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2011-03-15mmc: mmc_test: Only warn about not waiting for busy if it's supportedPawel Moll
If the MMC host controller does not support waiting for card signaling busy state (MMC_CAP_WAIT_WHILE_BUSY cap), there is no point in prining the relevant warning message. Signed-off-by: Pawel Moll <pawel.moll@arm.com> Reviewed-by: Matt Fleming <matt@console-pimps.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: Fixes for Dual Data Rate (DDR) supportAdrian Hunter
The DDR support patch needs the following fixes: - The block driver does not need to know about DDR, any more than it needs to know about bus width. - Not only the card must be switched to DDR mode. The host controller must also be configured, which is done through the 'set_ios()' function. - Do not set the DDR mode state until after the switch command is successful. - Setting block length is not supported in DDR mode. Make that a core function and change the other place it is used (mmc_test) also. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: fix display of .5 KiBAdrian Hunter
Append .5 to KiB display when there are an odd number of sectors. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: fix memory allocation segment limitsAdrian Hunter
Correctly allocate memory to meet the host controller driver's maximum segment size and count limits. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: move files from sysfs to debugfsAndy Shevchenko
As proposed by Greg K-H it is more logical to keep files for the mmc_test driver under debugfs. Additionally this patch brings seq_file API for show() method. It allows to write unlimited data to the file. Example of usage: # mount -t debugfs none /sys/kernel/debug # modprobe mmc_test [ 581.395843] mmc_test mmc0:0001: Card claimed for testing. # echo 25 > /sys/kernel/debug/mmc0/mmc0\:0001/test [ 604.568542] mmc0: Starting tests of card mmc0:0001... [ 604.582733] mmc0: Test case 25. Best-case read performance into scattered pages... [ 604.923553] mmc0: Transfer of 8192 sectors (4096 KiB) took 0.124664314 seconds (33644 kB/s, 32856 KiB/s) [ 604.933227] mmc0: Result: OK [ 604.936248] mmc0: Tests completed. # cat /sys/kernel/debug/mmc0/mmc0\:0001/test Test 25: 0 1 8192 0.124664314 33644784 Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: Greg KH <greg@kroah.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: Chris Ball <cjb@laptop.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: collect data and show it via sysfs by demandAndy Shevchenko
Make it possible to get test results via sysfs. It helps to do tests non-interactively. We have the file created under sysfs already and can use it to show test results. Prior to this patch, the "test" file under each card's sysfs node was write-only, and results were obtained by looking at dmesg. This patch improves programmatic access to the test results, making them available by reading back from the same "test" file: [root@host mmc0:e624]# echo 6 > test [root@host mmc0:e624]# cat test Test 6: 2 [cjb@laptop.org: changelog improvements] Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: Chris Ball <cjb@laptop.org> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: change simple_strtol() to strict_strtol()Andy Shevchenko
It's better to use strict_strtol() to convert user's input and strictly check it. At least it forbids to interpret wrong input as a 0 and prevents to run all tests. Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: use API to check card typeAndy Shevchenko
There are methods to check card type. Let's use them instead of direct checking type bits. Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc_test: fix performance tests that go over max_blk_countAdrian Hunter
The host controller driver limits I/O transfers to maximum transfer size, maximum block count, maximum segment size and maximum segment count. The performance tests were not obeying these limits which meant they would not work with some drivers. This patch fixes that. Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: rename dev_to_mmc_card() to mmc_dev_to_card()Andy Shevchenko
Global symbols should use their subsystem name in a prefixed fashion. Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-10-23mmc: make mmc_dev_to_card() macro publicAndy Shevchenko
Conversion from struct device to struct mmc_card is used more than in one place. Due to this it's better to have public macro for such thing. Signed-off-by: Andy Shevchenko <ext-andriy.shevchenko@nokia.com> Cc: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Chris Ball <cjb@laptop.org>
2010-08-12mmc_test: fix large memory allocationAdrian Hunter
- Fix mmc_test_alloc_mem. - Use nr_free_buffer_pages() instead of sysinfo.totalram to determine total lowmem pages. - Change variables containing memory sizes to unsigned long. - Limit maximum test area size to 128MiB because that is the maximum MMC high capacity erase size (the maxmium SD allocation unit size is just 4MiB) Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-08-12mmc_test: add performance testsAdrian Hunter
mmc_test provides tests aimed at testing SD/MMC hosts. This patch adds performance tests. It is advantageous to have performance tests in a kernel module like mmc_test for the following reasons: - transfer times can be measured very accurately - arbitrarily large transfers are possible - the effect of contiguous vs scattered pages can be determined The new tests are: 23. Best-case read performance 24. Best-case write performance 25. Best-case read performance into scattered pages 26. Best-case write performance from scattered pages 27. Single read performance by transfer size 28. Single write performance by transfer size 29. Single trim performance by transfer size 30. Consecutive read performance by transfer size 31. Consecutive write performance by transfer size 32. Consecutive trim performance by transfer size Signed-off-by: Adrian Hunter <adrian.hunter@nokia.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2010-03-30include cleanup: Update gfp.h and slab.h includes to prepare for breaking ↵Tejun Heo
implicit slab.h inclusion from percpu.h percpu.h is included by sched.h and module.h and thus ends up being included when building most .c files. percpu.h includes slab.h which in turn includes gfp.h making everything defined by the two files universally available and complicating inclusion dependencies. percpu.h -> slab.h dependency is about to be removed. Prepare for this change by updating users of gfp and slab facilities include those headers directly instead of assuming availability. As this conversion needs to touch large number of source files, the following script is used as the basis of conversion. http://userweb.kernel.org/~tj/misc/slabh-sweep.py The script does the followings. * Scan files for gfp and slab usages and update includes such that only the necessary includes are there. ie. if only gfp is used, gfp.h, if slab is used, slab.h. * When the script inserts a new include, it looks at the include blocks and try to put the new include such that its order conforms to its surrounding. It's put in the include block which contains core kernel includes, in the same order that the rest are ordered - alphabetical, Christmas tree, rev-Xmas-tree or at the end if there doesn't seem to be any matching order. * If the script can't find a place to put a new include (mostly because the file doesn't have fitting include block), it prints out an error message indicating which .h file needs to be added to the file. The conversion was done in the following steps. 1. The initial automatic conversion of all .c files updated slightly over 4000 files, deleting around 700 includes and adding ~480 gfp.h and ~3000 slab.h inclusions. The script emitted errors for ~400 files. 2. Each error was manually checked. Some didn't need the inclusion, some needed manual addition while adding it to implementation .h or embedding .c file was more appropriate for others. This step added inclusions to around 150 files. 3. The script was run again and the output was compared to the edits from #2 to make sure no file was left behind. 4. Several build tests were done and a couple of problems were fixed. e.g. lib/decompress_*.c used malloc/free() wrappers around slab APIs requiring slab.h to be added manually. 5. The script was run on all .h files but without automatically editing them as sprinkling gfp.h and slab.h inclusions around .h files could easily lead to inclusion dependency hell. Most gfp.h inclusion directives were ignored as stuff from gfp.h was usually wildly available and often used in preprocessor macros. Each slab.h inclusion directive was examined and added manually as necessary. 6. percpu.h was updated not to include slab.h. 7. Build test were done on the following configurations and failures were fixed. CONFIG_GCOV_KERNEL was turned off for all tests (as my distributed build env didn't work with gcov compiles) and a few more options had to be turned off depending on archs to make things build (like ipr on powerpc/64 which failed due to missing writeq). * x86 and x86_64 UP and SMP allmodconfig and a custom test config. * powerpc and powerpc64 SMP allmodconfig * sparc and sparc64 SMP allmodconfig * ia64 SMP allmodconfig * s390 SMP allmodconfig * alpha SMP allmodconfig * um on x86_64 SMP allmodconfig 8. percpu.h modifications were reverted so that it could be applied as a separate patch and serve as bisection point. Given the fact that I had only a couple of failures from tests on step 6, I'm fairly confident about the coverage of this conversion patch. If there is a breakage, it's likely to be something in one of the arch headers which should be easily discoverable easily on most builds of the specific arch. Signed-off-by: Tejun Heo <tj@kernel.org> Guess-its-ok-by: Christoph Lameter <cl@linux-foundation.org> Cc: Ingo Molnar <mingo@redhat.com> Cc: Lee Schermerhorn <Lee.Schermerhorn@hp.com>
2010-02-11mmc_test: block addressed cardsJohan Kristell
This patch fixes a bug in the multiblock write tests where the written data is read back for verifying one block at a time. The tests in mmc_test assumes that all cards are byte addressable. This will cause the multi block write tests to fail, leading the user of the mmc_test driver thinking there is something wrong with the sdhci driver they are testing. The start address for the block is calculated as: blocknum * 512. For block addressable cards the blocknum alone should be used. Signed-off-by: Johan Kristell <johan.kristell@axis.com> Cc: <linux-mmc@vger.kernel.org> Signed-off-by: Andrew Morton <akpm@linux-foundation.org> Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
2009-02-18mmc_test: fix basic read testRabin Vincent
Due to a typo in the Basic Read test, it's currently identical to the Basic Write test. Fix this. Signed-off-by: Rabin Vincent <rabin@rab.in> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-09-20mmc_test: initialize mmc_test_lock staticallyAkinobu Mita
The mutex mmc_test_lock is initialized at every time mmc_test device is probed. Probing another mmc_test device may break the mutex, if the probe function is called while the mutex is locked. This patch fixes it by statically initializing mmc_test_lock. Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com> Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-08-01mmc_test: Revert "mmc_test: test oversized sg lists"Pierre Ossman
This reverts commit 48b5352ea1891455eb8e824cf7d92f66931a090f. Oversized sg lists are not allowed anymore, and the core even checks for them in debug mode, so this test is entirely incorrect. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-23mmc_test: print message when attaching to cardPierre Ossman
Make it a bit more obvious that the card has been claimed by the mmc_test driver so that people don't have to wonder why their block device never shows up. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>
2008-07-23mmc_test: test oversized sg listsPierre Ossman
Add tests that make sure the driver properly checks the blocks and blksz fields and doesn't assume the sg list has a size that perfectly matches the current request. Signed-off-by: Pierre Ossman <drzeus@drzeus.cx>