| Age | Commit message (Collapse) | Author |
|---|
|
>From the pci power documentation:
"The driver itself should not call pm_runtime_allow(), though. Instead,
it should let user space or some platform-specific code do that (user space
can do it via sysfs as stated above)..."
However, the S0ix residency cannot be reached without MEI device getting
into low power state. Hence, for mei devices that support D0i3, it's better
to make runtime power management mandatory and not rely on the system
integration such as udev rules.
This policy cannot be applied globally as some older platforms
were found to have broken power management.
Cc: <stable@vger.kernel.org> v4.13+
Cc: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Reviewed-by: Alexander Usyskin <alexander.usyskin@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes in here as well.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
AT24 EEPROMs have a write-protect pin, which - when pulled high -
inhibits writes to the upper quadrant of memory (although it has been
observed that on some chips it disables writing to the entire memory
range).
On some boards, this pin is connected to a GPIO and pulled high by
default, which forces the user to manually change its state before
writing. On linux this means that we either need to hog the line all
the time, or set the GPIO value before writing from outside of the
at24 driver.
Make the driver check if the write-protect GPIO was defined in the
device tree and pull it low whenever writing to the EEPROM.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
|
|
The chip size passed via devicetree, i2c, or acpi device ids is now no
longer limited to a power of two. So the temporary fix can be removed.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Fundamental properties such as capacity and page size differ among
at24-type chips. But these chips do not have an id register, so this
can't be discovered at runtime.
Traditionally, at24-type eeprom properties were determined in two ways:
- by passing a 'struct at24_platform_data' via platform_data, or
- by naming the chip type in the devicetree, which passes a 'magic
number' to probe(), which is then converted to a 'struct
at24_platform_data'.
Recently a bug was discovered because the magic number rounds down all
chip sizes to the lowest power of two. This was addressed by
a work-around commit 5478e478eee3 ("eeprom: at24: correctly set the
size for at24mac402"), with the wish that magic numbers should over
time be converted to structs.
This patch replaces the magic numbers with 'struct at24_chip_data'.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
A regmap_config struct is pretty big and declaring two of them
statically just to tweak the reg_bits value adds unnecessary bloat.
Declare the regmap config locally in at24_probe() instead.
Bloat-o-meter output for ARM:
add/remove: 0/2 grow/shrink: 1/0 up/down: 4/-272 (-268)
Function old new delta
at24_probe 1560 1564 +4
regmap_config_8 136 - -136
regmap_config_16 136 - -136
Total: Before=7012, After=6744, chg -3.82%
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
There are a couple symbols defined in the driver source file which are
missing the at24_ prefix. This patch fixes that.
For module params: use module_param_named() in order to not break
userspace.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Fix issues reported by checkpatch for at24.c.
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Some multi-address eeproms in the at24 family may not automatically
roll-over reads to the next slave address. On those eeproms, reads
that straddle slave boundaries will not work correctly.
Solution:
Mark such eeproms with a flag that prevents reads straddling
slave boundaries. Add the AT24_FLAG_NO_RDROL flag to the eeprom
entry in the device_id table, or add 'no-read-rollover' to the
eeprom devicetree entry.
Note that I have not personally enountered an at24 chip that
does not support read rollovers. They may or may not exist.
However, my hardware requires this functionality because of
a quirk.
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Remove remaining now unneeded code dealing with SMBUS details.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Remove the old and now unused read functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Add regmap-based read function and instead of using three different
read functions (standard, mac, serial) use just one and factor out the
read offset adjustment for mac and serial to at24_adjust_read_offset.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Remove the old and now unused write functions.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Add a regmap-based write function.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
Change return type of at24_translate_offset to *at24_client to make
member regmap accessible for subsequent patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
This patch adds basic regmap support to be used by subsequent
patches of this series.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
This is a clean-up patch, no functional changes intended.
It removes the unused parameter of type "struct ddcb_requ*" from
the functions genwqe_user_vmap() and genwqe_user_vunmap().
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a clean-up patch, no functional changes intended.
It makes all defines uppercase, following a "tradition"
that helps to make code clearer.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This is a clean-up patch, no functional changes intended.
It removes an unused variable from do_execute_ddcb() and
also renames the function free_user_pages(), prepending
"genwqe" prefix in order to clarify the code.
Signed-off-by: Guilherme G. Piccoli <gpiccoli@linux.vnet.ibm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trivial fix to spelling mistake in dev_dbg debug message. Also
add in a missing comma.
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the macros should not use a trailing semicolon
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved the please, no space beofore tabs checkpatch
warning. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the Prefer 'unsigned int' to bare use of 'unsigned'
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the missing a blank line after declarations checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved open brace { should be on the previous line checkpatch
error. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the please, no space beofore tabs checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the missing a blank line after declarations checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The label 'done' in function vop_ioctl is not used, so remove it. Fixes
build warning:
drivers/misc/mic/vop/vop_vringh.c:1001:1: warning: label 'done' defined but
not used [-Wunused-label]
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Certain EEPROMS have a size that is larger than the number of address
bytes would allow, and store the MSB of the address in bit 3 of the
instruction byte.
This can be described in platform data using EE_INSTR_BIT3_IS_ADDR, or
in DT using the obsolete legacy "at25,addr-mode" property.
But currently there exists no non-deprecated way to describe this in DT.
Hence extend the existing "address-width" DT property to allow
specifying 9 address bits, and enable support for that in the driver.
This has been tested with a Microchip 25LC040A.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the Unnecessary space before function pointer arguments
checkpatch warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval.shah@softnautics.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull Page Table Isolation (PTI) preparatory tree from Ingo Molnar:
"This does a rename to free up linux/pti.h to be used by the upcoming
page table isolation feature"
* 'WIP.x86-pti.base.prep-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip:
drivers/misc/intel/pti: Rename the header file to free up the namespace
|
|
We'd like to use the 'PTI' acronym for 'Page Table Isolation' - free up the
namespace by renaming the <linux/pti.h> driver header to <linux/intel-pti.h>.
(Also standardize the header guard name while at it.)
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: J Freyensee <james_p_freyensee@linux.intel.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: linux-kernel@vger.kernel.org
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When mei driver is powering down due to suspend or shutdown
it will iterate over the mei client bus and disconnect
each client device attached in turn.
The power down flow consist of the link rest, which causes all clients
get disconnected at once, hence the individual disconnection
can be omitted and significantly reduce power down flow.
Signed-off-by: Tomas Winkler <tomas.winkler@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We want the fixes and changes in here for testing.
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Resolved all the missing a blank line after declarations checkpatch
warnings. Issue found by checkpatch.
Signed-off-by: Dhaval Shah <dhaval23031987@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
SPDX-License-Identifier is used for the hpilo.
Signed-off-by: Dhaval Shah <dhaval.experiance@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
It is not necessary to check return value of class_register.
enclosure_init returns both successful and error value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix checkpatch.pl error:
ERROR: space prohibited before open square bracket '['.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix coccicheck warning which recommends to use memdup_user():
drivers/misc/mic/vop/vop_vringh.c:940:14-21: WARNING opportunity for memdup_user
drivers/misc/mic/vop/vop_vringh.c:998:8-15: WARNING opportunity for memdup_user
Generated by: scripts/coccinelle/memdup_user/memdup_user.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Fix ptr_ret.cocci warnings:
drivers/misc/vexpress-syscfg.c:273:1-3: WARNING: PTR_ERR_OR_ZERO can be used
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR
Generated by: scripts/coccinelle/api/ptr_ret.cocci
Signed-off-by: Vasyl Gomonovych <gomonovych@gmail.com>
Acked-by: Liviu Dudau <liviu.dudau@arm.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Trying to read the MAC address from an eeprom that has an offset that
is not a multiple of 4 causes an error currently.
Fix it by changing the nvmem stride to 1.
Cc: stable@vger.kernel.org
Signed-off-by: David Lechner <david@lechnology.com>
[Bartosz: tweaked the commit message]
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
drivers/staging/rts5208/sd.o: In function `.sd_power_off_card3v3':
(.text+0x5760): multiple definition of `.sd_power_off_card3v3'
drivers/misc/cardreader/rtsx_pcr.o:(.text+0x4630): first defined here
drivers/staging/rts5208/sd.o:(.opd+0x378): multiple definition of `sd_power_off_card3v3'
drivers/misc/cardreader/rtsx_pcr.o:(.opd+0x4f8): first defined here
drivers/staging/rts5208/ms.o: In function `.ms_power_off_card3v3':
(.text+0x5e70): multiple definition of `.ms_power_off_card3v3'
drivers/misc/cardreader/rtsx_pcr.o:(.text+0x46e0): first defined here
drivers/staging/rts5208/ms.o:(.opd+0x360): multiple definition of `ms_power_off_card3v3'
drivers/misc/cardreader/rtsx_pcr.o:(.opd+0x510): first defined here
Fixes: 5da4e04ae480 ("misc: rtsx: Add support for RTS5260")
Signed-off-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The at24 driver creates dummy I2C devices to access offsets in the chip
that are outside the area supported using a single I2C address. It is not
meaningful to use runtime PM to such devices; the system firmware (ACPI)
does not know about these devices nor runtime PM was enabled for them.
Always use the real device instead of the dummy ones.
Fixes: 98e8201039af ("eeprom: at24: enable runtime pm support")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Tested-by: Sven Van Asbroeck on a 24AA16/24LC16B <svendev@arcx.com>
[Bartosz: rebased on top of previous fixes for 4.15, tweaked the
commit message]
[Sven: fixed Bartosz's rebase]
Signed-off-by: Sven Van Asbroeck <svendev@arcx.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux
Pull i2c fixes from Wolfram Sang:
"Here are two bugfixes for I2C, fixing a memleak in the core and irq
allocation for i801.
Also three bugfixes for the at24 eeprom driver which Bartosz collected
while taking over maintainership for this driver"
* 'i2c/for-current' of git://git.kernel.org/pub/scm/linux/kernel/git/wsa/linux:
eeprom: at24: check at24_read/write arguments
eeprom: at24: fix reading from 24MAC402/24MAC602
eeprom: at24: correctly set the size for at24mac402
i2c: i2c-boardinfo: fix memory leaks on devinfo
i2c: i801: Fix Failed to allocate irq -2147483648 error
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
* no need for callback argument - it's always the same one
* fold __qp_memcpy_from_queue() into its only caller, get rid of dead code
* pass struct iov_iter * without casting to void *
* don't pass buf_size at all - it's always iov_iter_count(to)
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
switch both of its users to qp_memcpy_from_queue_iov() - just
make it take iov_iter * instead of msghdr * and arrange for a
iov_iter for it in all cases.
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
Both qp_dequeue_locked() and qp_enqueue_locked() use the
buf_size argument to decide how much would be there to copy;
in case of iovec- (== msghdr-)based primitives it's not
iov_size, it's msg_data_left(msg).
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc fixes from Michael Ellerman:
"Two fixes for nasty kexec/kdump crashes in certain configurations.
A couple of minor fixes for the new TIDR code.
A fix for an oops in a CXL error handling path.
Thanks to: Andrew Donnellan, Christophe Lombard, David Gibson, Mahesh
Salgaonkar, Vaibhav Jain"
* tag 'powerpc-4.15-3' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux:
powerpc: Do not assign thread.tidr if already assigned
powerpc: Avoid signed to unsigned conversion in set_thread_tidr()
powerpc/kexec: Fix kexec/kdump in P9 guest kernels
powerpc/powernv: Fix kexec crashes caused by tlbie tracing
cxl: Check if vphb exists before iterating over AFU devices
|
|
So far we completely rely on the caller to provide valid arguments.
To be on the safe side perform an own sanity check.
Cc: stable@vger.kernel.org
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Bartosz Golaszewski <brgl@bgdev.pl>
|
