| Age | Commit message (Collapse) | Author |
|---|
|
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When the initial support was added for this PMIC was added
only regulator support was present. Now we have GPIO and Powerbutton
support as well. Hence correct the description of MFD_TPS65218 config
option.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Replace the two separate calls for setting the irq handler and data with
a single irq_set_chained_handler_and_data() call.
Signed-off-by: Martin Kaiser <martin@kaiser.cx>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Enable power saving for RTS5250S as following steps:
1.Set 0xFE58 to enable clock power management.
2.Check cfg space whether support L1SS or not.
3.If support L1SS, set 0xFF03 to free clkreq.
4.When entering idle status, enable aspm
and set parameters for L1SS and LTR.
5.Wnen entering run status, disable aspm
and set parameters for L1SS and LTR.
If entering L1SS mode successfully,
electric current will be below 2mA.
Signed-off-by: Rui Feng <rui_feng@realsil.com.cn>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds the MFD driver for Dollar Cove (TI version) PMIC with
ACPI INT33F5 that is found on some Intel Cherry Trail devices.
The driver is based on the original work by Intel, found at:
https://github.com/01org/ProductionKernelQuilts
This is a minimal version for adding the basic resources. Currently,
only ACPI PMIC opregion and the external power-button are used.
Bugzilla: https://bugzilla.kernel.org/show_bug.cgi?id=193891
Signed-off-by: Takashi Iwai <tiwai@suse.de>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Acked-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds muic of_compatible in order to use the muic device
driver in device tree.
Signed-off-by: Maciej Purski <m.purski@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Reviewed-by: Krzysztof Kozlowski <krzk@kernel.org>
Acked-by: Rob Herring <robh@kernel.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Don't populate the arrays vcore_val, vpll_val and vaux_val on the
stack, instead make them static const. Makes the object code smaller
by over 370 bytes:
Before:
text data bss dec hex filename
6971 3248 64 10283 282b drivers/mfd/stw481x.o
After:
text data bss dec hex filename
6338 3504 64 9906 26b2 drivers/mfd/stw481x.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Currently the driver boots only via device tree hence add a
dependency on CONFIG_OF. This leaves with a bunch of unused code
so clean that up. This patch also makes use of probe_new function
in place of the probe function so as to avoid passing i2c_device_id.
Signed-off-by: Keerthy <j-keerthy@ti.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Push the system suspend/resume callbacks of intel-lpss to the late
suspend/early resume stages to allow child device callbacks to be
pushed to the late/early stages of suspend/resume too, so as to
make it possible to avoid resuming the children if they are runtime-
suspended during system suspend going forward.
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
Tested-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Tested-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Johannes Stezenbach <js@sig21.net>
Tested-by: Rajat Jain <rajatja@google.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
This code has now been moved to the audio subsystem so is no longer
required in the MFD code.
Signed-off-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
The WM9705, WM9712 and WM9713 are highly integrated codecs, with an
audio codec, DAC and ADC, GPIO unit and a touchscreen interface.
Historically the support was spread across drivers/input/touchscreen and
sound/soc/codecs. The sharing was done through ac97 bus sharing. This
model will not withstand the new AC97 bus model, where codecs are
discovered on runtime.
Signed-off-by: Robert Jarzmik <robert.jarzmik@free.fr>
Acked-by: Charles Keepax <ckeepax@opensource.wolfsonmicro.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>
|
|
... and __initconst if applicable.
Based on similar work for an older kernel in the Grsecurity patch.
[JD: fix toshiba-wmi build]
[JD: add htcpen]
[JD: move __initconst where checkscript wants it]
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jean Delvare <jdelvare@suse.de>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers
- RK805 Power Management IC (PMIC)
- ROHM BD9571MWV-M MFD Power Management IC (PMIC)
- Texas Instruments TPS68470 Power Management IC (PMIC) & LEDs
New Device Support:
- Add support for HiSilicon Hi6421v530 to hi6421-pmic-core
- Add support for X-Powers AXP806 to axp20x
- Add support for X-Powers AXP813 to axp20x
- Add support for Intel Sunrise Point LPSS to intel-lpss-pci
New Functionality:
- Amend API to provide register layout; atmel-smc
Fix-ups:
- DT re-work; omap, nokia
- Header file location change {I2C => MFD}; dm355evm_msp, tps65010
- Fix chip ID formatting issue(s); rk808
- Optionally register touchscreen devices; da9052-core
- Documentation improvements; twl-core
- Constification; rtsx_pcr, ab8500-core, da9055-i2c, da9052-spi
- Drop unnecessary static declaration; max8925-i2c
- Kconfig changes (missing deps and remove module support)
- Slim down oversized licence statement; hi6421-pmic-core
- Use managed resources (devm_*); lp87565
- Supply proper error checking/handling; t7l66xb
Bug Fixes:
- Fix counter duplication issue; da9052-core
- Fix potential NULL deference issue; max8998
- Leave SPI-NOR write-protection bit alone; lpc_ich
- Ensure device is put into reset during suspend; intel-lpss
- Correct register offset variable size; omap-usb-tll"
* tag 'mfd-next-4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (61 commits)
mfd: intel_soc_pmic: Differentiate between Bay and Cherry Trail CRC variants
mfd: intel_soc_pmic: Export separate mfd-cell configs for BYT and CHT
dt-bindings: mfd: Add bindings for ZII RAVE devices
mfd: omap-usb-tll: Fix register offsets
mfd: da9052: Constify spi_device_id
mfd: intel-lpss: Put I2C and SPI controllers into reset state on suspend
mfd: da9055: Constify i2c_device_id
mfd: intel-lpss: Add missing PCI ID for Intel Sunrise Point LPSS devices
mfd: t7l66xb: Handle return value of clk_prepare_enable
mfd: Add ROHM BD9571MWV-M PMIC DT bindings
mfd: intel_soc_pmic_chtwc: Turn Kconfig option into a bool
mfd: lp87565: Convert to use devm_mfd_add_devices()
mfd: Add support for TPS68470 device
mfd: lpc_ich: Do not touch SPI-NOR write protection bit on Haswell/Broadwell
mfd: syscon: atmel-smc: Add helper to retrieve register layout
mfd: axp20x: Use correct platform device ID for many PEK
dt-bindings: mfd: axp20x: Introduce bindings for AXP813
mfd: axp20x: Add support for AXP813 PMIC
dt-bindings: mfd: axp20x: Add AXP806 to supported list of chips
mfd: Add ROHM BD9571MWV-M MFD PMIC driver
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management updates from Rafael Wysocki:
"This time (again) cpufreq gets the majority of changes which mostly
are driver updates (including a major consolidation of intel_pstate),
some schedutil governor modifications and core cleanups.
There also are some changes in the system suspend area, mostly related
to diagnostics and debug messages plus some renames of things related
to suspend-to-idle. One major change here is that suspend-to-idle is
now going to be preferred over S3 on systems where the ACPI tables
indicate to do so and provide requsite support (the Low Power Idle S0
_DSM in particular). The system sleep documentation and the tools
related to it are updated too.
The rest is a few cpuidle changes (nothing major), devfreq updates,
generic power domains (genpd) framework updates and a few assorted
modifications elsewhere.
Specifics:
- Drop the P-state selection algorithm based on a PID controller from
intel_pstate and make it use the same P-state selection method
(based on the CPU load) for all types of systems in the active mode
(Rafael Wysocki, Srinivas Pandruvada).
- Rework the cpufreq core and governors to make it possible to take
cross-CPU utilization updates into account and modify the schedutil
governor to actually do so (Viresh Kumar).
- Clean up the handling of transition latency information in the
cpufreq core and untangle it from the information on which drivers
cannot do dynamic frequency switching (Viresh Kumar).
- Add support for new SoCs (MT2701/MT7623 and MT7622) to the mediatek
cpufreq driver and update its DT bindings (Sean Wang).
- Modify the cpufreq dt-platdev driver to autimatically create
cpufreq devices for the new (v2) Operating Performance Points (OPP)
DT bindings and update its whitelist of supported systems (Viresh
Kumar, Shubhrajyoti Datta, Marc Gonzalez, Khiem Nguyen, Finley
Xiao).
- Add support for Ux500 to the cpufreq-dt driver and drop the
obsolete dbx500 cpufreq driver (Linus Walleij, Arnd Bergmann).
- Add new SoC (R8A7795) support to the cpufreq rcar driver (Khiem
Nguyen).
- Fix and clean up assorted issues in the cpufreq drivers and core
(Arvind Yadav, Christophe Jaillet, Colin Ian King, Gustavo Silva,
Julia Lawall, Leonard Crestez, Rob Herring, Sudeep Holla).
- Update the IO-wait boost handling in the schedutil governor to make
it less aggressive (Joel Fernandes).
- Rework system suspend diagnostics to make it print fewer messages
to the kernel log by default, add a sysfs knob to allow more
suspend-related messages to be printed and add Low Power S0 Idle
constraints checks to the ACPI suspend-to-idle code (Rafael
Wysocki, Srinivas Pandruvada).
- Prefer suspend-to-idle over S3 on ACPI-based systems with the
ACPI_FADT_LOW_POWER_S0 flag set and the Low Power Idle S0 _DSM
interface present in the ACPI tables (Rafael Wysocki).
- Update documentation related to system sleep and rename a number of
items in the code to make it cleare that they are related to
suspend-to-idle (Rafael Wysocki).
- Export a variable allowing device drivers to check the target
system sleep state from the core system suspend code (Florian
Fainelli).
- Clean up the cpuidle subsystem to handle the polling state on x86
in a more straightforward way and to use %pOF instead of full_name
(Rafael Wysocki, Rob Herring).
- Update the devfreq framework to fix and clean up a few minor issues
(Chanwoo Choi, Rob Herring).
- Extend diagnostics in the generic power domains (genpd) framework
and clean it up slightly (Thara Gopinath, Rob Herring).
- Fix and clean up a couple of issues in the operating performance
points (OPP) framework (Viresh Kumar, Waldemar Rymarkiewicz).
- Add support for RV1108 to the rockchip-io Adaptive Voltage Scaling
(AVS) driver (David Wu).
- Fix the usage of notifiers in CPU power management on some
platforms (Alex Shi).
- Update the pm-graph system suspend/hibernation and boot profiling
utility (Todd Brandt).
- Make it possible to run the cpupower utility without CPU0 (Prarit
Bhargava)"
* tag 'pm-4.14-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (87 commits)
cpuidle: Make drivers initialize polling state
cpuidle: Move polling state initialization code to separate file
cpuidle: Eliminate the CPUIDLE_DRIVER_STATE_START symbol
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
PM: docs: Delete the obsolete states.txt document
PM: docs: Describe high-level PM strategies and sleep states
PM / devfreq: Fix memory leak when fail to register device
PM / devfreq: Add dependency on PM_OPP
PM / devfreq: Move private devfreq_update_stats() into devfreq
PM / devfreq: Convert to using %pOF instead of full_name
PM / AVS: rockchip-io: add io selectors and supplies for RV1108
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpuidle: Convert to using %pOF instead of full_name
cpufreq: Convert to using %pOF instead of full_name
PM / Domains: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
...
|
|
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
This commits makes the intel_soc_pmic_core code check the _HRV of the
ACPI-firmware-node and selects intel_soc_pmic_config_byt_crc resp.
intel_soc_pmic_config_cht_crc based on this.
This fixes the Bay Trail specific ACPI OpRegion code causing problems
on Cherry Trail devices. Specifically this was causing the external
microsd slot on a Dell Venue 8 5855 (Cherry Trail version) to not work
and the eMMC to become unreliable and throw lots of errors.
Fixes: 5165238460 ("mfd: intel_soc_pmic: Core driver")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Both Bay and Cherry Trail devices may be used together with a Crystal Cove
PMIC. Each platform has its own variant of the PMIC, which both use the
same ACPI HID, but they are not 100% compatible.
Looking at the android x86 kernel sources where most of the Crystal Cove
code comes from, it talks about "Valley View", "Bay Trail" and / or BYT
without ever mentioning Cherry Trail, with the exception of the regulator
driver. The Asus Zenfone-2 kernel code has 2 regulator drivers, one
for Crystal Cove and one for what it calls Crystal Cove Plus. The
Crystal Cove Plus regulator driver is the only one to mention Cherry
Trail and that driver uses different register addresses then the
normal (Bay Trail) Crystal Cove regulator driver, showing that at
least the regulator register addresses are different.
The GPIO code should work on both, and the PWM code is known to work on
both and is necessary for backlight control on some Cherry Trail devices.
Testing has shown that the ACPI OpRegion code otoh is causing problems
on Cherry Trail devices, which is not surprising as it deals with the
regulators and those have different register addresses on CHT.
Specifically the ACPI OpRegion code causes the external microsd slot on
a Dell Venue 8 5855 (Cherry Trail version) to not work and the eMMC to
become unreliable and throw lots of errors.
This commit replaces the single mfd_cell array currently used for Crystal
Cove with 2 separate arrays, one for the Bay Trail variant and one for
the Cherry Trail variant, note that the Cherry Trail version of the array
only contains gpio and pwm cells. The PMIC OpRegion cell is deliberately
not included and drivers for the other cells in the Bay Trail cell array
were never upstreamed.
Fixes: 7cf0a66f32 ("mfd: intel_soc_pmic: Crystal Cove support")
Reported-and-tested-by: russianneuromancer <russianneuromancer@ya.ru>
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
gcc-8 notices that the register number calculation is wrong
when the offset is an 'u8' but the number is larger than 256:
drivers/mfd/omap-usb-tll.c: In function 'omap_tll_init':
drivers/mfd/omap-usb-tll.c:90:46: error: overflow in conversion from 'int' to 'u8 {aka unsigned char}' chages value from 'i * 256 + 2070' to '22' [-Werror=overflow]
This addresses it by always using a 32-bit offset number for
the register. This is apparently an old problem that previous
compilers did not find.
Fixes: 16fa3dc75c22 ("mfd: omap-usb-tll: HOST TLL platform driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
spi_device_id are not supposed to change at runtime. All functions
working with spi_device_id provided by <linux/i2c.h> work with
const spi_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Commit 274e43edcda6f ("mfd: intel-lpss: Do not put device in reset
state on suspend") changed the behavior on suspend by not putting LPSS
controllers into reset. This was done because S3/S0ix fail if UART
device is put into reset and no_console_suspend flag is enabled.
Because of the above change, I2C controller gets into a bad state if
it observes that the I2C lines are pulled low when power to I2C device
is cut off during suspend (generally, I2C lines are pulled to power
rail of the I2C device in order to ensure that there is no leakage
because of the pulls when device is turned off). This results in the
controller timing out for all future I2C operations after resume. It
is primarily because of the following sequence of operations:
During suspend:
1. I2C controller is disabled, but it is not put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
==> At this point the I2C controller gets into a bad state
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled.
However, even after enabling the I2C controller, all future I2C xfers
fail since the controller is in a bad state and does not attempt to
make any transactions and hence times out.
In order to ensure that the controller does not get into a bad state,
this change puts it into reset if the controller type is not
UART. With this change, the order of operations is:
During suspend:
1. I2C controller is disabled and put into reset.
2. Power to I2C device is cut off.
3. #2 results in the I2C lines being pulled low.
On resume:
1. Power to I2C device is enabled.
2. #2 results in the I2C lines being pulled high.
3. I2C controller is enabled and taken out of reset.
Signed-off-by: Furquan Shaikh <furquan@google.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
i2c_device_id are not supposed to change at runtime. All functions
working with i2c_device_id provided by <linux/i2c.h> work with
const i2c_device_id. So mark the non-const structs as const.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This patch adds a missing PCI ID of the Intel Sunrise Point chipset to the Intel LPSS driver.
It fixes a bug causing the touchpad of the Lenovo Yoga 720-15 not to be recognized.
See also bug 1700657 on bugs.launchpad.net.
Many thanks to CoolStar, who found this solution!
Reported-by: CoolStar <coolstarorganization@gmail.com>
Tested-by: Mike Schwartz <mykesx@gmail.com>
Tested-by: Björn Dahlgren <bjodah@gmail.com>
Signed-off-by: Florian R. Hölzlwimmer <git.ich@frhoelzlwimmer.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
clk_prepare_enable() can fail here and we must check its return value.
we must disable clock, if t7l66xb_probe is not successful.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The PMIC provides ACPI OpRegions which must be available for other
drivers' PS0 / PS3 methods early-on as such it must be builtin as the
Kconfig help text already states.
Somehow its Kconfig option ended up being a tristate though, this fixes
this.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
This fixes missing mfd_remove_devices() call when unload the module.
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Reviewed-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The TPS68470 device is an advanced power management
unit that powers a Compact Camera Module (CCM),
generates clocks for image sensors, drives a dual
LED for Flash and incorporates two LED drivers for
general purpose indicators.
This patch adds support for TPS68470 mfd device.
Signed-off-by: Rajmohan Mani <rajmohan.mani@intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
At least on Lenovo Thinkpad Yoga, the BIOS seems to monitor the SPI-NOR
write protection bit and if it is flipped to read/write it assumes the
BIOS configuration was changed on next reboot. It then, for unknown
reasons, resets the BIOS settings back to default.
We can prevent this by just leaving the write protection bit intact and
let the SPI-NOR driver know whether the device is writable or not. In
case of this particular Lenovo the SPI-NOR flash will be exposed as
read-only.
Fixes: ff00d7a32a1b ("mfd: lpc_ich: Add support for SPI serial flash host controller")
Link: https://bugzilla.kernel.org/show_bug.cgi?id=195951
Reported-by: Abdó Roig-Marange <abdo.roig@gmail.com>
Signed-off-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
According to their datasheets, the AXP221, AXP223, AXP288, AXP803,
AXP809 and AXP813 PEK have different values for startup time bits from
the AXP20X, let's use the platform device id with the correct values.
Signed-off-by: Quentin Schulz <quentin.schulz@free-electrons.com>
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The X-Powers AXP813 PMIC is normally used with Allwinner's A83T SoC.
It has the same range of functions as other X-Powers PMICs, such as
DC-DC buck converter and linear regulator outputs, AC-IN and VBUS
power supplies, power button trigger, GPIOs, ADCs, and a battery
charger.
Note that the IRQ table given in the datasheet is incorrect: in IRQ
enable/status registers 1, there are separate IRQs for ACIN and VBUS,
instead of bits [7:5] being the same as bits [4:2]. So it shares the
same IRQs as the AXP803, rather than the AXP288.
This patch adds basic mfd support for it, with only the power button
enabled.
Signed-off-by: Chen-Yu Tsai <wens@csie.org>
Acked-by: Maxime Ripard <maxime.ripard@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add the MFD part of the ROHM BD9571MWV-M PMIC driver and MAINTAINERS
entry. The MFD part only specifies the regmap bits for the PMIC and
binds the subdevs together.
Signed-off-by: Marek Vasut <marek.vasut+renesas@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Add support for HiSilicon Hi6421v530 PMIC. Hi6421v530 communicates with
main SoC via memory-mapped I/O.
Hi6421v530 and Hi6421 are PMIC chips from the same vendor, HiSilicon,
but at different revisions. They share the same memory-mapped I/O
design. They differ in integrated devices, such as regulator details,
LDO voltage points.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Signed-off-by: Wang Xiaoyin <hw.wangxiaoyin@hisilicon.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Update dev_err messages to make them more readable.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Change license text to a shorter form of GPLv2.
Signed-off-by: Guodong Xu <guodong.xu@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
MTF_CORE should be enabled when driver is enabled.
Without this patch you can configure:
CONFIG_MFD_CORE is not set
CONFIG_MFD_TPS65086=y
... which ends up with compilation error:
drivers/mfd/tps65086.o: In function `tps65086_probe':
drivers/mfd/tps65086.c:110: undefined reference to `mfd_add_devices'
drivers/mfd/tps65086.c:110:(.text+0x128): relocation truncated to fit: \
R_AARCH64_CALL26 against undefined symbol `mfd_add_devices'
Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
attribute_groups are not supposed to change at runtime. All functions
working with attribute_groups provided by <linux/sysfs.h> work with const
attribute_group. So mark the non-const structs as const.
File size before:
text data bss dec hex filename
16298 1009 184 17491 4453 drivers/mfd/ab8500-core.o
File size After adding 'const':
text data bss dec hex filename
16490 817 184 17491 4453 drivers/mfd/ab8500-core.o
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
if 'max8998_i2c_parse_dt_pdata() fails (when out of memory), a NULL
pointer dereference will occur in the error handling code.
Return directly instead.
Fixes: ee999fb3f17f("mfd: max8998: Add support for Device Tree")
Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Drop static on a local variable, when the variable is initialized before
any use, on every possible execution path through the function. The static
has no benefit, and dropping it reduces the code size.
The semantic patch that fixes this problem is as follows:
(http://coccinelle.lip6.fr/)
// <smpl>
@bad exists@
position p;
identifier x;
type T;
@@
static T x@p;
...
x = <+...x...+>
@@
identifier x;
expression e;
type T;
position p != bad.p;
@@
-static
T x@p;
... when != x
when strict
?x = e;
// </smpl>
The change in code size is indicates by the following output from the size
command.
before:
text data bss dec hex filename
2579 240 16 2835 b13 drivers/mfd/max8925-i2c.o
after:
text data bss dec hex filename
2531 240 8 2779 adb drivers/mfd/max8925-i2c.o
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Acked-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
It is possible that under heavy system load, the counter in the completion
struct, used for waiting for end of AD conversion, gets incremented twice.
To make sure the driver recovers from this situation, the completion struct
should be reinitialized.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Don't populate the arrays depath and cd_mask on the stack but make
them static const. Makes the object code smaller:
text data bss dec hex filename
25413 7216 448 33077 8135 drivers/mfd/rtsx_pcr.o
text data bss dec hex filename
25151 7360 448 32959 80bf drivers/mfd/rtsx_pcr.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Saying it "returns the result" seems tautological. The read function
does not return num_bytes on success, it returns zero on success. I
noticed this discrepancy because some of the callers were checking for
>= 0.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'ib-mfd-hwmon-4.14', 'ib-mfd-iio-pwm-4.14', 'ib-mfd-input-rtc-4.14', 'ib-mfd-many-4.14' and 'ib-mfd-pinctrl-regulator-4.14' into ibs-for-mfd-merged
|
|
STM32 Low-Power Timer hardware block can be used for:
- PWM generation
- IIO trigger (in sync with PWM)
- IIO quadrature encoder counter
PWM and IIO timer configuration are mixed in the same registers so
we need a multi fonction driver to be able to share those registers.
Signed-off-by: Fabrice Gasnier <fabrice.gasnier@st.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
include/linux/i2c is not for client devices. Move the header file to a
more appropriate location.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Acked-by: Jonathan Cameron <jic23@kernel.org>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Kishon Vijay Abraham I <kishon@ti.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Thierry Reding <thierry.reding@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Daniel Thompson <daniel.thompson@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging
Pull hwmon updates from Guenter Roeck:
- new drivers:
- Lantiq CPU temperature sensor
- IBM CFF power supply
- TPS53679 PMBus driver
- new support:
- LM5066I (lm25066 PMBus driver)
- Intel VID protocol VR13 (PMBus drivers)
- CAT34TS02C, GT30TS00, GT34TS02, and CAT34TS04 (jc42 driver)
- cleanup and minor improvements in several drivers
* tag 'hwmon-for-linus-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/groeck/linux-staging: (36 commits)
hwmon: (ltq-cputemp) add cpu temp sensor driver
hwmon: (ltq-cputemp) add devicetree bindings documentation
hwmon: (pmbus) Add support for Texas Instruments tps53679 device
hwmon: (asc7621) make several arrays static const
hwmon: (pmbus/lm25066) Add support for TI LM5066I
hwmon: (pmbus/lm25066) Offset coefficient depends on CL
hwmon: (pmbus) Add support for Intel VID protocol VR13
Documentation: hwmon: Document the IBM CFF power supply
hwmon: (pmbus) Add IBM Common Form Factor (CFF) power supply driver
dt-bindings: hwmon: Document the IBM CCF power supply version 1
hwmon: (ftsteutates) constify i2c_device_id
hwmon: da9052: Add support for TSI channel
mfd: da9052: Make touchscreen registration optional
hwmon: da9052: Replace S_IRUGO with 0444
mfd: da9052: Add register details for TSI
hwmon: (aspeed-pwm) add THERMAL dependency
hwmon: (pmbus) Add debugfs for status registers
hwmon: (aspeed-pwm-tacho) cooling device support.
Documentation: dt-bindings: aspeed-pwm-tacho cooling device.
hwmon: (pmbus): Add generic alarm bit for iin and pin
...
|
|
* pm-cpufreq: (33 commits)
cpufreq: imx6q: Fix imx6sx low frequency support
cpufreq: speedstep-lib: make several arrays static, makes code smaller
cpufreq: ti: Fix 'of_node_put' being called twice in error handling path
cpufreq: dt-platdev: Drop few entries from whitelist
cpufreq: dt-platdev: Automatically create cpufreq device with OPP v2
ARM: ux500: don't select CPUFREQ_DT
cpufreq: Convert to using %pOF instead of full_name
cpufreq: Cap the default transition delay value to 10 ms
cpufreq: dbx500: Delete obsolete driver
mfd: db8500-prcmu: Get rid of cpufreq dependency
cpufreq: enable the DT cpufreq driver on the Ux500
cpufreq: Loongson2: constify platform_device_id
cpufreq: dt: Add r8a7796 support to to use generic cpufreq driver
cpufreq: remove setting of policy->cpu in policy->cpus during init
cpufreq: mediatek: add support of cpufreq to MT7622 SoC
cpufreq: mediatek: add cleanups with the more generic naming
cpufreq: rcar: Add support for R8A7795 SoC
cpufreq: dt: Add rk3328 compatible to use generic cpufreq driver
cpufreq: s5pv210: add missing of_node_put()
cpufreq: Allow dynamic switching with CPUFREQ_ETERNAL latency
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC fixes from Arnd Bergmann:
"A small number of bugfixes, again nothing serious.
- Alexander Dahl found multiple bugs in the Atmel memory interface
driver
- A randconfig build fix for at91 was incomplete, the second attempt
fixes the remaining corner case
- One fix for the TI Keystone queue handler
- The Odroid XU4 HDMI port (added in 4.13) needs a small DT fix"
* tag 'armsoc-fixes' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc:
ARM: dts: exynos: add needs-hpd for Odroid-XU3/4
ARM: at91: don't select CONFIG_ARM_CPU_SUSPEND for old platforms
soc: ti: knav: Add a NULL pointer check for kdev in knav_pool_create
memory: atmel-ebi: Fix smc cycle xlate converter
memory: atmel-ebi: Allow t_DF timings of zero ns
memory: atmel-ebi: Fix smc timing return value evaluation
|
|
The ARMSS clock, also known as the operating point of the
CPU, should not cross-depend on cpufreq like this. Move
the code to use just frequencies and remove the false
frequency (1GHz) and put in the actual frequency provided
by the ARMSS clock (998400000 Hz) as part of the process.
After this and the related cpufreq patch, the DB8500 will
simply use the standard DT cpufreq driver to change the
operating points through the common clock framework using
the ARMSS clock.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
This patch was applied to the MFD twice, causing unwanted behavour.
This reverts commit b77eb79acca3203883e8d8dbc7f2b842def1bff8.
Fixes: b77eb79acca3 ("mfd: da9061: Fix to remove BBAT_CONT register from chip model")
Reported-by: Steve Twiss <stwiss.opensource@diasemi.com>
Reviewed-by: Steve Twiss <stwiss.opensource@diasemi.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
If the touchscreen pins are used as general purpose analogue
input, the touchscreen driver should not be used. The pins
will be handled by the existing hwmon driver instead.
Signed-off-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Signed-off-by: Joseph Chen <chenjh@rock-chips.com>
Signed-off-by: Heiko Stuebner <heiko@sntech.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
