summaryrefslogtreecommitdiff
path: root/drivers/mfd/stmpe.c
AgeCommit message (Collapse)Author
2016-11-16mfd: stmpe: Fix RESET regression on STMPE2401Linus Walleij
Since commit c4dd1ba355aae2bc3d1213da6c66c53e3c31e028 ("mfd: stmpe: Add reset support for all STMPE variant") we're resetting the STMPE expanders before use. This caused a regression on the STMP2401 on the Nomadik NHK8815: stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101 nmk-i2c 101f8000.i2c0: write to slave 0x43 timed out nmk-i2c 101f8000.i2c0: no ack received after address transmission stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101 nmk-i2c 101f8000.i2c0: write to slave 0x44 timed out nmk-i2c 101f8000.i2c0: no ack received after address transmission It turns out that we start to poll for the reset bit to go low again too quickly: the STMPE2401 is not yet online and ready to be asked for the status of the RESET bit. By introducing a 10ms delay before starting to hammer the register for information, we get back to normal: stmpe-i2c 0-0043: stmpe2401 detected, chip id: 0x101 stmpe-i2c 0-0044: stmpe2401 detected, chip id: 0x101 Cc: stable@vger.kernel.org Cc: Amelie Delaunay <amelie.delaunay@st.com> Fixes: c4dd1ba355aa ("mfd: stmpe: Add reset support for all STMPE variant") Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: Add STMPE1600 supportPatrice Chotard
STMPE1600 is a 16-bit port expander. Datasheet is available here : http://www2.st.com/content/st_com/en/products/interfaces-and-transceivers/ i-o-expanders-and-level-translators/i-o-expanders/stmpe1600.html Signed-off-by: Amelie DELAUNAY <amelie.delaunay@st.com> Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Rework registers accessPatrice Chotard
this update allows to use registers map as following : regs[reg_index + offset] instead of regs[reg_index] + offset This makes code clearer and will facilitate the addition of STMPE1600 on which LSB and MSB registers are respectively located at addr and addr + 1. Despite for all others STMPE variant, LSB and MSB registers are respectively located in reverse order at addr + 1 and addr. For variant which have 3 registers's bank, we use LSB,CSB and MSB indexes which contains respectively LSB (or LOW), CSB (or MID) and MSB (or HIGH) register addresses (STMPE1801/STMPE24xx). For variant which have 2 registers's bank, we use LSB and CSB indexes only. In this case the CSB index contains the MSB regs address (STMPE 1601). Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Use generic bit mask namePatrice Chotard
In order to prepare the ground to STMPE1600, as STMPE1600's SYS_CTRL register has the same layout as STMPE801 variant, unify STMPExxx_REG_SYS_CTRL_RESET/INT_EN/INT_HI bit masks to more generic STMPE_SYS_CTRL_RESET/INT_EN/INT_HI Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Add reset support for all STMPE variantPatrice Chotard
Reset was only implemented for STMPE1801 variant despite all variant have a SOFT_RESET bit. For STMPE2401/2403/801/1601/1801 SOFT_RESET bit is bit 7 of SYS_CTRL register. For STMPE610/811 (which have the same variant id) SOFT_RESET bit is bit 1 of SYS_CTRL register. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-08-10mfd: stmpe: Add STMPE_IDX_SYS_CTRL/2 enumPatrice Chotard
As STMPE1801/1601/24xx has a SYS_CTRL register and STMPE1601/2403 has even a SYS_CTRL2 register, add STMPE_IDX_SYS_CTRL/2 and update driver code accordingly This update prepares the ground for not yet supported STMPE1600 which share similar REG_SYS_CTRL register. Signed-off-by: Patrice Chotard <patrice.chotard@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-06-29mfd: stmpe: Move platform data into MFD driverLinus Walleij
The STMPE platform data is only populated from the device tree in all existing users, so push the struct and make the OF case the norm. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2016-03-16mfd: stmpe: Add the proper PWM resourcesLinus Walleij
This adds the PWM resources to the STMPE MFD driver, so that it can properly grab and use them. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-10-26mfd: stmpe: PWM on 24xx has altfunc 1Linus Walleij
On the STMPE2401 and STMPE2401 altfunction 1 corresponds to the PWM channels. This oneliner was missing in the case-switch, making it impossible to enable the PWM channel output. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-08-11mfd: Kill off set_irq_flags usageRob Herring
set_irq_flags is ARM specific with custom flags which have genirq equivalents. Convert drivers to use the genirq interfaces directly, so we can kill off set_irq_flags. The translation of flags is as follows: IRQF_VALID -> !IRQ_NOREQUEST IRQF_PROBE -> !IRQ_NOPROBE IRQF_NOAUTOEN -> IRQ_NOAUTOEN For IRQs managed by an irqdomain, the irqdomain core code handles clearing and setting IRQ_NOREQUEST already, so there is no need to do this in .map() functions and we can simply remove the set_irq_flags calls. Some users also modify IRQ_NOPROBE and this has been maintained although it is not clear that is really needed. There appears to be a great deal of blind copy and paste of this code. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2015-06-22mfd: Constify regmap and irq configuration dataKrzysztof Kozlowski
Constify in various drivers configuration data which is not modified: - regmap_irq_chip, - individual regmap_irq's in array, - regmap_config, - irq_domain_ops, Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-12-30Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull input layer fixes from Dmitry Torokhov: "Fixes for v7 protocol for ALPS devices and few other driver fixes. Also users can request input events to be stamped with boot time timestamps, in addition to real and monotonic timestamps" * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: Input: hil_kbd - fix incorrect use of init_completion Input: alps - v7: document the v7 touchpad packet protocol Input: alps - v7: fix finger counting for > 2 fingers on clickpads Input: alps - v7: sometimes a single touch is reported in mt[1] Input: alps - v7: ignore new packets Input: evdev - add CLOCK_BOOTTIME support Input: psmouse - expose drift duration for IBM trackpoints Input: stmpe - bias keypad columns properly Input: stmpe - enforce device tree only mode mfd: stmpe: add pull up/down register offsets for STMPE Input: optimize events_per_packet count calculation Input: edt-ft5x06 - fixed a macro coding style issue Input: gpio_keys - replace timer and workqueue with delayed workqueue Input: gpio_keys - allow separating gpio and irq in device tree
2014-12-15mfd: stmpe: add pull up/down register offsets for STMPELinus Walleij
This adds the register offsets for pull up/down for the STMPE 1601, 1801 and 24xx expanders. This is used to bias GPIO lines and keypad lines. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2014-09-26mfd: stmpe: Support gpio over irq under device treeSean Cross
The stmpe_platform_data has a irq_over_gpio field, which allows the system to read STMPE events whenever an IRQ occurs on a GPIO pin. This patch adds the ability to configure this field and to use a GPIO as an IRQ source for boards configuring the STMPE in device tree. Signed-off-by: Sean Cross <xobs@kosagi.com> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-09-26mfd: stmpe: Rid variable length array Sparse warningsLee Jones
Numbers are generated by taking the largest currently used values. drivers/mfd/stmpe.c:252:17: warning: Variable length array is used. drivers/mfd/stmpe.c:857:16: warning: Variable length array is used. Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-07-09mfd: stmpe: Rid data size incompatibility warn when building for 64bitLee Jones
Extinguishes: ../drivers/mfd/stmpe-i2c.c: In function ‘stmpe_i2c_probe’: ../drivers/mfd/stmpe-i2c.c:88:13: warning: cast from pointer to integer of different size partnum = (int)of_id->data; Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-05-23mfd: stmpe: root out static GPIO and IRQ assignmentsLinus Walleij
The only platform using the STMPE expander now boots from device tree using all-dynamic GPIO and IRQ number assignments, so remove the mechanism to pass this from the device tree entirely. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-09mfd: stmpe: add optional regulatorsLinus Walleij
The STMPE has VCC and VIO supply lines, and sometimes (as on Ux500) this comes from a software-controlled regulator. Make it possible to supply the STMPE with power from these regulators. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-05-09mfd: stmpe: mask off unused blocks properlyLinus Walleij
The STMPE driver would just read/modify/write the system control register on the STMPE1601, meaning it would not properly mask off the PWM block, which remained active if it was on at boot time. This makes sure the blocks are always masked off if they were active on boot, saving some power. Also rename the inconsistenty named STMPE1601 define for the PWM block activation. Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2014-03-19mfd: stmpe: Trivial: Remove unnecessary semicolonSachin Kamat
Semicolon is not necessary after the while statement. Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2014-01-06mfd: stmicro: Constify struct mfd_cell where possibleGeert Uytterhoeven
As of commit 03e361b25ee8dfb1fd9b890072c23c4aae01c6c7 ("mfd: Stop setting refcounting pointers in original mfd_cell arrays"), the "cell" parameter of mfd_add_devices() is "const" again. Hence make all cell data passed to mfd_add_devices() const where possible. Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-07-31mfd: stmpe: Staticise stmpe_of_probe()Mark Brown
It is only called from this file so there is no need for it to be in the global namespace and cause sparse to warn. Signed-off-by: Mark Brown <broonie@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org>
2013-06-25mfd: stmpe: use irq_get_trigger_type() to get IRQ flagsJavier Martinez Canillas
Use irq_get_trigger_type() to get the IRQ trigger type flags instead calling irqd_get_trigger_type(irq_get_irq_data(irq)) Signed-off-by: Javier Martinez Canillas <javier.martinez@collabora.co.uk> Acked-by: Grant Likely <grant.likely@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Samuel Ortiz <sameo@linux.intel.com> Cc: Jason Cooper <jason@lakedaemon.net> Cc: Andrew Lunn <andrew@lunn.ch> Cc: Russell King <linux@arm.linux.org.uk> Cc: Ralf Baechle <ralf@linux-mips.org> Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org> Cc: linux-arm-kernel@lists.infradead.org Cc: linux-mips@linux-mips.org Link: http://lkml.kernel.org/r/1371228049-27080-5-git-send-email-javier.martinez@collabora.co.uk Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
2013-04-09mfd: support stmpe1801 18 bits enhanced port expanderJean-Nicolas Graux
Provides support for 1801 variant of stmpe gpio port expanders. This chip has 18 gpios configurable as GPI, GPO, keypad matrix, special key or dedicated key function. Note that special/dedicated key function is not supported yet. Signed-off-by: Jean-Nicolas Graux <jean-nicolas.graux@stericsson.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-05mfd: stmpe: DT: Add stmpe-i2c dt alias to get id deviceGabriel Fernandez
This patch augments the STMP driver to read the device id from the stmpe-i2c dt alias if present. Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-04-05mfd: stmpe: DT: Enable no-irq mode configurationGabriel Fernandez
If there is no interrupt property into stmpe node then activate the no-irq mode by setting the irq value to -1. Cc: devicetree-discuss@lists.ozlabs.org Signed-off-by: Gabriel Fernandez <gabriel.fernandez@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2013-01-03Drivers: mfd: remove __dev* attributes.Greg Kroah-Hartman
CONFIG_HOTPLUG is going away as an option. As a result, the __dev* markings need to be removed. This change removes the use of __devinit, __devexit_p, __devinitdata, __devinitconst, and __devexit from these drivers. Based on patches originally written by Bill Pemberton, but redone by me in order to handle some of the coding style issues better, by hand. Cc: Bill Pemberton <wfp5p@virginia.edu> Cc: Samuel Ortiz <sameo@linux.intel.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2012-12-18Merge branch 'for-linus' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input Pull second round of input updates from Dmitry Torokhov: "As usual, there are a couple of new drivers, input core now supports managed input devices (devres), a slew of drivers now have device tree support and a bunch of fixes and cleanups." * 'for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/dtor/input: (71 commits) Input: walkera0701 - fix crash on startup Input: matrix-keymap - provide a proper module license Input: gpio_keys_polled - switch to using gpio_request_one() Input: gpio_keys - switch to using gpio_request_one() Input: wacom - fix touch support for Bamboo Fun CTH-461 Input: xpad - add a few new VID/PID combinations Input: xpad - minor formatting fixes Input: gpio-keys-polled - honor 'autorepeat' setting in platform data Input: tca8418-keypad - switch to using managed resources Input: tca8418_keypad - increase severity of failures in probe() Input: tca8418_keypad - move device ID tables closer to where they are used Input: tca8418_keypad - use dev_get_platdata() to retrieve platform data Input: tca8418_keypad - use a temporary variable for parent device Input: tca8418_keypad - add support for shared interrupt Input: tca8418_keypad - add support for device tree bindings Input: remove Compaq iPAQ H3600 (Bitsy) touchscreen driver Input: bu21013_ts - add support for Device Tree booting Input: bu21013_ts - move GPIO init and exit functions into the driver Input: bu21013_ts - request regulator that actually exists ARM: ux500: Strip out duplicate touch screen platform information ...
2012-12-16Merge tag 'mfd-3.8-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6 Pull MFS update from Samuel Ortiz: "This is the MFD patch set for the 3.8 merge window. We have several new drivers, most of the time coming with their sub devices drivers: - Austria Microsystem's AS3711 - Nano River's viperboard - TI's TPS80031, AM335x TS/ADC, - Realtek's MMC/memstick card reader - Nokia's retu We also got some notable cleanups and improvements: - tps6586x got converted to IRQ domains. - tps65910 and tps65090 moved to the regmap IRQ API. - STMPE is now Device Tree aware. - A general twl6040 and twl-core cleanup, with moves to the regmap I/O and IRQ APIs and a conversion to the recently added PWM framework. - sta2x11 gained regmap support. Then the rest is mostly tiny cleanups and fixes, among which we have Mark's wm5xxx and wm8xxx patchset." Far amount of annoying but largely trivial conflicts. Many due to __devinit/exit removal, others due to one or two of the new drivers also having come in through another tree. * tag 'mfd-3.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-2.6: (119 commits) mfd: tps6507x: Convert to devm_kzalloc mfd: stmpe: Update DT support for stmpe driver mfd: wm5102: Add readback of DSP status 3 register mfd: arizona: Log if we fail to create the primary IRQ domain mfd: tps80031: MFD_TPS80031 needs to select REGMAP_IRQ mfd: tps80031: Add terminating entry for tps80031_id_table mfd: sta2x11: Fix potential NULL pointer dereference in __sta2x11_mfd_mask() mfd: wm5102: Add tuning for revision B mfd: arizona: Defer patch initialistation until after first device boot mfd: tps65910: Fix wrong ack_base register mfd: tps65910: Remove unused data mfd: stmpe: Get rid of irq_invert_polarity mfd: ab8500-core: Fix invalid free of devm_ allocated data mfd: wm5102: Mark DSP memory regions as volatile mfd: wm5102: Correct default for LDO1_CONTROL_2 mfd: arizona: Register haptics devices mfd: wm8994: Make current device behaviour the default mfd: tps65090: MFD_TPS65090 needs to select REGMAP_IRQ mfd: Fix stmpe.c build when OF is not enabled mfd: jz4740-adc: Use devm_kzalloc ...
2012-12-10mfd: stmpe: Update DT support for stmpe driverVipul Kumar Samar
This patch extends existing DT support for stmpe devices. This updates: - missing header files in stmpe.c - stmpe_of_probe() with pwm, rotator and new bindings. - Bindings are updated in binding document. Acked-by: Lee Jones <lee.jones@linaro.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-12-01gpio: stmpe: Add DT support for stmpe gpioVipul Kumar Samar
This patch allows the STMPE GPIO driver to be successfully probed and initialised when Device Tree support is enabled. Bindings are mentioned in Documentation too. Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
2012-11-30mfd: stmpe: Get rid of irq_invert_polarityViresh Kumar
Since the very first patch, stmpe core driver is using irq_invert_polarity as part of platform data. But, nobody is actually using it in kernel till now. Also, this is not something part of hardware specs, but is included to cater some board mistakes or quirks. So, better get rid of it. This is earlier discussed here: https://lkml.org/lkml/2012/11/27/636 Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-26mfd: Fix stmpe.c build when OF is not enabledRandy Dunlap
Fix build errors when CONFIG_OF is not enabled by including <linux/of.h> (needs to be added in any case). An alternative fix could be to make the driver depend on OF. drivers/mfd/stmpe.c:1025:2: error: implicit declaration of function 'of_property_read_u32' drivers/mfd/stmpe.c:1030:2: error: implicit declaration of function 'for_each_child_of_node' drivers/mfd/stmpe.c:1030:36: error: expected ';' before '{' token Signed-off-by: Randy Dunlap <rdunlap@infradead.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-26mfd: Simplify IRQ domain registration code in STMPELee Jones
Historically, a driver would have to decide whether it required a Linear or Legacy IRQ domain when registering one. This can end up as quite a lot of code. A new Simple call now exists which simplifies this process. Let's make use of it here. Reviewed-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-24Input: stmpe-keypad - add support for Device Tree bindingsDmitry Torokhov
This patch allows the STMPE driver to be successfully probed and initialised when Device Tree support is enabled. Besides the usual platform data changes, we also separate the process of filling in the 'in use' pin bitmap, as we have to extract the information from Device Tree in the DT boot case. Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-23mfd: stmpe: Use devm_*() routinesViresh Kumar
This patch frees stmpe driver from tension of freeing resources. devm_* derivatives of multiple routines are used while allocating resources, which would be freed automatically by kernel. Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Acked-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-22Input: stmpe-ts - add DT support for stmpe touchscreenVipul Kumar Samar
This patch allows the STMPE Touchscreen driver to be successfully probed and initialised when Device Tree support is enabled. Bindings are mentioned in Documentation too. Signed-off-by: Vipul Kumar Samar <vipulkumar.samar@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org> Signed-off-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
2012-11-11mfd: Enable the STMPE MFD for Device TreeLee Jones
This patch allows the STMPE Multi-Functional Device to be correctly initialised when booting with Device Tree support enabled. Its children are specified by the addition of subordinate devices to the STMPE node in the Device Tree file. Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11mfd: Correct copy and paste mistake in stmpeLee Jones
When specifying IRQ numbers for the stmpe1601, IRQ defines for the stmpe24xx were used instead. Fortunately, the defined numbers are the same, hence why it survived testing. This fix is merely an aesthetic one. Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11mfd: Provide the STMPE driver with its own IRQ domainLee Jones
The STMPE driver is yet another IRQ controller which requires its own IRQ domain. So, we provide it with one. Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-11-11mfd: Prevent STMPE from abusing mfd_add_devices' irq_base parameterLee Jones
Originally IRQ incrementers were provided in some template resource structures for keypad and touchscreen devices. These were passed as IORESOURCE_IRQs to MFD core in the usual way. The true device IRQs were instead added to the irq_base when mfd_add_devices was invoked. This is clearly an abuse of the call, and does not scale when IRQ Domains are brought into play. Before we can provide the STMPE with its own IRQ Domain we must first fix this. This patche keeps most of the driver's structure, keeping the template strategy. However, instead of providing the IRQ as an increment to irq_base, we dynamically populate the IORESOURCE_IRQ with the correct device IRQ. Acked-by: Arnd Bergmann <arnd@arndb.de> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Lee Jones <lee.jones@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-09-15mfd: core: Push irqdomain mapping out into devicesMark Brown
Currently the MFD core supports remapping MFD cell interrupts using an irqdomain but only if the MFD is being instantiated using device tree and only if the device tree bindings use the pattern of registering IPs in the device tree with compatible properties. This will be actively harmful for drivers which support non-DT platforms and use this pattern for their DT bindings as it will mean that the core will silently change remapping behaviour and it is also limiting for drivers which don't do DT with this particular pattern. There is also a potential fragility if there are interrupts not associated with MFD cells and all the cells are omitted from the device tree for some reason. Instead change the code to take an IRQ domain as an optional argument, allowing drivers to take the decision about the parent domain for their interrupts. The one current user of this feature is ab8500-core, it has the domain lookup pushed out into the driver. Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-03-06mfd: Add support for no-interrupt stmpe configChris Blair
Adds support for boards which have an STMPE device without the interrupt pin connected. Acked-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Chris Blair <chris.blair@stericsson.com> Tested-by: Michel Jaouen <michel.jaouen@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Fix stmpe section mismatchSamuel Ortiz
This fixes: WARNING: drivers/built-in.o(.text+0xf368f): Section mismatch in reference from the function stmpe_probe() to the function .devinit.text:stmpe_chip_init() The function stmpe_probe() references the function __devinit stmpe_chip_init(). Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Fix stmpe build warningSamuel Ortiz
This fixes: drivers/mfd/stmpe.c:114:1: warning: data definition has no type or storage class [enabled by default] drivers/mfd/stmpe.c:114:1: warning: type defaults to 'int' in declaration of 'EXPORT_SYMBOL_GPL' [-Wimplicit-int] Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Add support for stmpe variant 801Viresh Kumar
STMPE801 is a GPIO expander. Registers for 801 are much different from other variants. This patch adds support for STMPE801 in stmpe mfd driver. Signed-off-by: Bhupesh Sharma <bhupesh.sharma@st.com> Signed-off-by: Pratyush Anand <pratyush.anand@st.com> Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Add support for stmpe variant 610Viresh Kumar
STMPE610 is very much like STMPE811, except the number of gpio pins, which is 8 in 811 and 6 in 610. This patch adds support for variant 610. STMPE610 will share most of the code with STMPE811. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Separate out STMPE controller and interface specific codeViresh Kumar
Few STMPE controller can have register interface over SPI or I2C. Current implementation only supports I2C and all code is present in a single file stmpe.c. It would be better to separate out I2C interface specific code from controller specific code. Later SPI specific code can be added in a separate file. This patch separates out I2C and controller specific code into separate files, making stmpe.c independent of I2C. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2012-01-09mfd: Add support for irq over gpio pin to stmpeViresh Kumar
On many boards, stmpe is present as an separate device (not as part of SoC). Here gpio lines are mostly used for getting interrupts. This patch adds in support to handle irq over gpio pin. Signed-off-by: Viresh Kumar <viresh.kumar@st.com> Acked-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
2011-07-31mfd: Fix missing stmpe kerneldocOm Prakash
Generating kerneldoc for STMPE result in warnings, so fix this by adding missing documentation. Signed-off-by: Om Prakash <omprakash.pal@stericsson.com> Reviewed-by: Rabin Vincent <rabin.vincent@stericsson.com> Reviewed-by: Jonas Aberg <jonas.aberg@stericsson.com> Reviewed-by: Srinidhi Kasagar <srinidhi.kasagar@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
generated by cgit v1.2.3 (git 2.25.1) at 2024-12-15 07:35:04 +0000