| Age | Commit message (Collapse) | Author |
|---|
|
The DSI PLLs are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The display clocks are handled by the generic clock framework
since ages, this code is completely unused and misleading.
Delete it.
Cc: Stephan Gerhold <stephan@gerhold.net>
Cc: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
AB8505 support was never fully converted to the device tree.
Most of the MFD cells for AB8505 lack an "of_compatible",
which prevents them from being configured through the device tree.
Align the definition of the AB8505 MFD cells with the ones for AB8500,
and add device tree compatibles. Except for GPIO and regulators the
compatibles are equal to those used for AB8500 because the hardware
does not differ much.
Finally, change db8500_prcmu_register_ab8500() to check for the AB8505
device tree node additionally, and probe it if it is found.
Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There is a distinct version of the Ux500 U8420 variant
with "sysclk", as can be seen from the vendor code that
didn't make it upstream, this firmware lacks the
ULPPLL (ultra-low power phase locked loop) which in
effect means that the timer clock is instead wired to
the 32768 Hz always-on clock.
This has some repercussions when enabling the timer
clock as the code as it stands will disable the timer
clock on these platforms (lacking the so-called
"doze mode") and obtaining the wrong rate of the timer
clock.
The timer frequency is of course needed very early in
the boot, and as a consequence, we need to shuffle
around the early PRCMU init code: whereas in the past
we did not need to look up the PRCMU firmware version
in the early init, but now we need to know the version
before the core system timers are registered so we
restructure the platform callbacks to the PRCMU so as
not to take any arguments and instead look up the
resources it needs directly from the device tree
when initializing.
As we do not yet support any platforms using this
firmware it is not a regression, but as PostmarketOS
is starting to support products with this firmware we
need to fix this up.
The low rate of 32kHz also makes the MTU timer unsuitable
as delay timer but this needs to be fixed in a separate
patch.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Stephan Gerhold <stephan@gerhold.net>
Acked-by: Olof Johansson <olof@lixom.net>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
... with and without 'resources'.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal
Pull thermal SoC updates from Eduardo Valentin:
"This is a really small pull in the midst of a lot of pending patches.
We are in the middle of restructuring how we are maintaining the
thermal subsystem, as per discussion in our last LPC. For now, I am
sending just some changes that were pending in my tree. Looking
forward to get a more streamlined process in the next merge window"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/evalenti/linux-soc-thermal:
thermal: db8500: Rewrite to be a pure OF sensor
thermal: db8500: Use dev helper variable
thermal: db8500: Finalize device tree conversion
thermal: thermal_mmio: remove some dead code
|
|
At some point there was an attempt to convert the DB8500
thermal sensor to device tree: a probe path was added
and the device tree was augmented for the Snowball board.
The switchover was never completed: instead the thermal
devices came from from the PRCMU MFD device and the probe
on the Snowball was confused as another set of configuration
appeared from the device tree.
Move over to a device-tree only approach, as we fixed up
the device trees.
Cc: Vincent Guittot <vincent.guittot@linaro.org>
Acked-by: Lee Jones <lee.jones@linaro.org>
Reviewed-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
The DB8520 used in a lot of Samsung phones has a slightly higher
maximum ARMSS frequency than the DB8500. In order to not confuse
the OPP framework and cpufreq, make sure the PRCMU driver
returns the correct frequency.
Cc: Stephan Gerhold <stephan@gerhold.net>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
We don't need dev_err() messages when platform_get_irq() fails now that
platform_get_irq() prints an error message itself when something goes
wrong. Let's remove these prints with a simple semantic patch.
// <smpl>
@@
expression ret;
struct platform_device *E;
@@
ret =
(
platform_get_irq(E, ...)
|
platform_get_irq_byname(E, ...)
);
if ( \( ret < 0 \| ret <= 0 \) )
{
(
-if (ret != -EPROBE_DEFER)
-{ ...
-dev_err(...);
-... }
|
...
-dev_err(...);
)
...
}
// </smpl>
While we're here, remove braces on if statements that only have one
statement (manually).
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/db8500-prcmu.c: In function 'dsiclk_rate':
drivers/mfd/db8500-prcmu.c:1592:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1593:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI_2:
^~~~
drivers/mfd/db8500-prcmu.c:1594:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1595:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Mark switch cases where we are expecting to fall through.
This patch fixes the following warnings:
drivers/mfd/db8500-prcmu.c: In function 'dsiclk_rate':
drivers/mfd/db8500-prcmu.c:1592:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1593:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI_2:
^~~~
drivers/mfd/db8500-prcmu.c:1594:7: warning: this statement may fall through [-Wimplicit-fallthrough=]
div *= 2;
~~~~^~~~
drivers/mfd/db8500-prcmu.c:1595:2: note: here
case PRCM_DSI_PLLOUT_SEL_PHI:
^~~~
Reported-by: Stephen Rothwell <sfr@canb.auug.org.au>
Reviewed-by: Kees Cook <keescook@chromium.org>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Gustavo A. R. Silva <gustavo@embeddedor.com>
|
|
Based on 1 normalized pattern(s):
license terms gnu general public license v2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 37 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Steve Winslow <swinslow@gmail.com>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190528170027.724130665@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/mfd/Kconfig:config MFD_DB8500_PRCMU
drivers/mfd/Kconfig: bool "ST-Ericsson DB8500 Power Reset Control Management Unit"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We replace module.h with init.h and export.h ; the latter since the
file does export some symbols.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Reviewed-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When building the kernel with Clang, the following section mismatch
warnings appear:
WARNING: vmlinux.o(.text+0x7239cc): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:init_prcm_registers()
The function db8500_prcmu_probe() references
the function __init init_prcm_registers().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of init_prcm_registers is wrong.
WARNING: vmlinux.o(.text+0x723e28): Section mismatch in reference from
the function db8500_prcmu_probe() to the function
.init.text:fw_project_name()
The function db8500_prcmu_probe() references
the function __init fw_project_name().
This is often because db8500_prcmu_probe lacks a __init
annotation or the annotation of fw_project_name is wrong.
db8500_prcmu_probe should not be marked as __init so remove the __init
annotation from fw_project_name and init_prcm_registers.
Signed-off-by: Nathan Chancellor <natechancellor@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The ARMSS clock, also known as the operating point of the
CPU, should not cross-depend on cpufreq like this. Move
the code to use just frequencies and remove the false
frequency (1GHz) and put in the actual frequency provided
by the ARMSS clock (998400000 Hz) as part of the process.
After this and the related cpufreq patch, the DB8500 will
simply use the standard DT cpufreq driver to change the
operating points through the common clock framework using
the ARMSS clock.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
To enable eventual removal of pr_warning
This makes pr_warn use consistent for drivers/mfd
Prior to this patch, there were 4 uses of pr_warning and
9 uses of pr_warn in drivers/mfd
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
There are no call sites for these functions. Strip them out.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Except for the constant DB8500_PRCMU_FW_VERSION_OFFSET number, nothing
is ever passed through the platform data and used in a driver, so we
can simply stop passing it around.
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd
Pull MFD updates from Lee Jones:
"New Drivers:
- Freescale Touch Screen ADC
- X-Powers AXP PMIC with RSB
- TI TPS65086 Power Management IC (PMIC)
New Device Support:
- Supply device PCI IDs for Intel Broxton
Fix-ups:
- Move to clkdev_create() API; intel_quark_i2c_gpio
- Complete re-write of TI's TPS65912 Power Management IC (PMIC)
- Remove unnecessary function argument; axp20x
- Separate out bus related code; axp20x
- Coding Style changes; axp20x
- Allow more drivers to be compiled as modules
- Work around false positive 'used uninitialised' warning; db8500-prcmu
Bug Fixes:
- Remove do_div(); fsl-imx25-gcq
- Fix driver init when built-in; tps65010
- Fix clock-unregister leak; intel-lpss"
* tag 'mfd-for-linus-4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd: (53 commits)
mfd: intel-lpss: Pass I2C configuration via properties on BXT
mfd: imx6sx: Add PCIe register definitions for iomuxc gpr
mfd: ipaq-micro: Use __maybe_unused to hide pm functions
mfd: max77686: Add max77802 to I2C device ID table
mfd: max77686: Export OF module alias information
mfd: max77686: Allow driver to be built as a module
mfd: stmpe: Add the proper PWM resources
mfd: tps65090: Set regmap config reg counts properly
mfd: syscon: Return ENOTSUPP instead of ENOSYS when disabled
mfd: as3711: Set regmap config reg counts properly
mfd: rc5t583: Set regmap config reg counts properly
gpio: tps65086: Add GPO driver for the TPS65086 PMIC
mfd: mt6397: Add platform device ID table
mfd: da9063: Fix missing volatile registers in the core regmap_range volatile lists
mfd: mt6397: Add MT6323 support to MT6397 driver
mfd: mt6397: Add support for different Slave types
mfd: mt6397: int_con and int_status may vary in location
dt-bindings: mfd: Add bindings for the MediaTek MT6323 PMIC
mfd: da9062: Fix missing volatile registers in the core regmap_range volatile lists
mfd: Add documentation for ACT8945A DT bindings
...
|
|
The prcmu_config_clkout() function ensures that the 'clkout' argument
can only be '0' or '1' using an appropriate BUG_ON(), so the compiler
should know that the div_mask, mask, and bits variables are always
initialized later on. However, it doesn't understand this in gcc-5.2
and produces a false positive warning instead:
drivers/mfd/db8500-prcmu.c: In function 'prcmu_config_clkout':
drivers/mfd/db8500-prcmu.c:762:10: error: 'div_mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if (val & div_mask) {
^
drivers/mfd/db8500-prcmu.c:769:13: error: 'mask' may be used uninitialized in this function [-Werror=maybe-uninitialized]
if ((val & mask & ~div_mask) != bits) {
^
drivers/mfd/db8500-prcmu.c:757:7: error: 'bits' may be used uninitialized in this function [-Werror=maybe-uninitialized]
Replacing the switch() statement with an equivalent if() lets
gcc figure this out reliably and avoids the warnings.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
When the thermal subsystem is a loadable module, the u8500 driver
fails to build:
drivers/thermal/built-in.o: In function `db8500_thermal_probe':
db8500_thermal.c:(.text+0x96c): undefined reference to `thermal_zone_device_register'
drivers/thermal/built-in.o: In function `db8500_thermal_work':
db8500_thermal.c:(.text+0xab4): undefined reference to `thermal_zone_device_update'
This changes the symbol to a tristate, so Kconfig can track the
dependency correctly.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Eduardo Valentin <edubezval@gmail.com>
|
|
set_irq_flags is ARM specific with custom flags which have genirq
equivalents. Convert drivers to use the genirq interfaces directly, so we
can kill off set_irq_flags. The translation of flags is as follows:
IRQF_VALID -> !IRQ_NOREQUEST
IRQF_PROBE -> !IRQ_NOPROBE
IRQF_NOAUTOEN -> IRQ_NOAUTOEN
For IRQs managed by an irqdomain, the irqdomain core code handles clearing
and setting IRQ_NOREQUEST already, so there is no need to do this in
.map() functions and we can simply remove the set_irq_flags calls. Some
users also modify IRQ_NOPROBE and this has been maintained although it
is not clear that is really needed. There appears to be a great deal of
blind copy and paste of this code.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Constify in various drivers configuration data which is not modified:
- regmap_irq_chip,
- individual regmap_irq's in array,
- regmap_config,
- irq_domain_ops,
Signed-off-by: Krzysztof Kozlowski <k.kozlowski.k@gmail.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Remove the function prcmu_get_boot_status() that is not used anywhere.
This was partially found by using a static code analysis program called cppcheck.
Signed-off-by: Rickard Strandqvist <rickard_strandqvist@spectrumdigital.se>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pull driver core update from Greg KH:
"Here's the set of driver core patches for 3.19-rc1.
They are dominated by the removal of the .owner field in platform
drivers. They touch a lot of files, but they are "simple" changes,
just removing a line in a structure.
Other than that, a few minor driver core and debugfs changes. There
are some ath9k patches coming in through this tree that have been
acked by the wireless maintainers as they relied on the debugfs
changes.
Everything has been in linux-next for a while"
* tag 'driver-core-3.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (324 commits)
Revert "ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries"
fs: debugfs: add forward declaration for struct device type
firmware class: Deletion of an unnecessary check before the function call "vunmap"
firmware loader: fix hung task warning dump
devcoredump: provide a one-way disable function
device: Add dev_<level>_once variants
ath: ath9k: use debugfs_create_devm_seqfile() helper for seq_file entries
ath: use seq_file api for ath9k debugfs files
debugfs: add helper function to create device related seq_file
drivers/base: cacheinfo: remove noisy error boot message
Revert "core: platform: add warning if driver has no owner"
drivers: base: support cpu cache information interface to userspace via sysfs
drivers: base: add cpu_device_create to support per-cpu devices
topology: replace custom attribute macros with standard DEVICE_ATTR*
cpumask: factor out show_cpumap into separate helper function
driver core: Fix unbalanced device reference in drivers_probe
driver core: fix race with userland in device_add()
sysfs/kernfs: make read requests on pre-alloc files use the buffer.
sysfs/kernfs: allow attributes to request write buffer be pre-allocated.
fs: sysfs: return EGBIG on write if offset is larger than file size
...
|
|
Also rid superfluous gotos and label.
Cc: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Error check around return value of devm_ioremap is missing. Add the same
to avoid NULL pointer dereference.
Signed-off-by: Pramod Gurav <pramod.gurav@smartplayin.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
A platform_driver does not need to set an owner, it will be populated by the
driver core.
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
A check for CONFIG_DBX500_PRCMU_DEBUG was added in v3.6. But there's no
Kconfig symbol DBX500_PRCMU_DEBUG. So remove this check.
Signed-off-by: Paul Bolle <pebolle@tiscali.nl>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
mfd_add_devices() expects array of struct mfd_cell to be const.
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The cpufreq core now supports the cpufreq_for_each_entry macro helper
for iteration over the cpufreq_frequency_table, so use it.
It should have no functional changes.
Signed-off-by: Stratos Karafotis <stratosk@semaphore.gr>
Acked-by: Viresh Kumar <viresh.kumar@linaro.org>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
The DBx500 and ABx500 should be getting their IRQs from the
device tree and nowhere else. Get rid of all the static assignments
everywhere, delete it from the driver, platform data and the
board files in one swift strike.
Lots of cross-dependencies in the MFD drivers for PRCMU and
AB8500 makes it necessary to strike everywhere at once to
eradicate IRQs passed as resources and platform data to the left
and right around the platform.
Cc: Mark Brown <broonie@kernel.org>
Cc: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
As of commit 03e361b25ee8dfb1fd9b890072c23c4aae01c6c7 ("mfd: Stop setting
refcounting pointers in original mfd_cell arrays"), the "cell" parameter of
mfd_add_devices() is "const" again. Hence make all cell data passed to
mfd_add_devices() const where possible.
Signed-off-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
The platform which it pertains to is no longer supported and is actually
causing some confusion in the new common clock implementation. A recent
patch removed its use in the clock driver, let's take out the definitions
too.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next
Pull MFD (multi-function device) updates from Samuel Ortiz:
"For the 3.12 merge window we have one new driver for the DA9063 PMIC
from Dialog Semiconductor.
Besides that driver we also have:
- Device tree support for the s2mps11 driver
- More devm_* conversion for the pm8921, max89xx, menelaus, tps65010,
wl1273 and pcf50633-adc drivers.
- A conversion to threaded IRQ and IRQ domain for the twl6030 driver.
- A fairly big update for the rtsx driver: Better power saving
support, better vendor settings handling, and a few fixes.
- Support for a couple more boards (COMe-bHL6 and COMe-cTH6) for the
Kontron driver.
- A conversion to the dev_get_platdata() API for all MFD drivers.
- A removal of non-DT (legacy) support for the twl6040 driver.
- A few fixes and additions (Mic detect level) to the wm5110 register
tables.
- Regmap support for the davinci_voicecodec driver.
- The usual bunch of minor cleanups and janitorial fixes"
* tag 'mfd-3.12-1' of git://git.kernel.org/pub/scm/linux/kernel/git/sameo/mfd-next: (81 commits)
mfd: ucb1x00-core: Rewrite ucb1x00_add_dev()
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for event name
mfd: ab8500-debugfs: Apply a check for -ENOMEM after allocating memory for sysfs
mfd: timberdale: Use module_pci_driver
mfd: timberdale: Remove redundant break
mfd: timberdale: Staticize local variables
mfd: ab8500-debugfs: Staticize local variables
mfd: db8500-prcmu: Staticize clk_mgt
mfd: db8500-prcmu: Use ANSI function declaration
mfd: omap-usb-host: Staticize usbhs_driver_name
mfd: 88pm805: Fix potential NULL pdata dereference
mfd: 88pm800: Fix potential NULL pdata dereference
mfd: twl6040: Use regmap for register cache
mfd: davinci_voicecodec: Provide a regmap for register I/O
mfd: davinci_voicecodec: Remove unused read and write functions
mmc: memstick: rtsx: Modify copyright comments
mmc: rtsx: Clear SD_CLK toggle enable bit if switching voltage fail
mfd: mmc: rtsx: Change default tx phase
mfd: pcf50633-adc: Use devm_*() functions
mfd: rtsx: Copyright modifications
...
|
|
clk_mgt is used only in this file. Make it static.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Silences the following warning:
drivers/mfd/db8500-prcmu.c:2322:25: warning:
non-ANSI function declaration of function 'prcmu_ac_sleep_req'
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Sachin Kamat <sachin.kamat@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
To break the dependency on the "id.h" file we move the cpuidle driver
to a platform device. Now we only call the probe() on this driver if
we find a corresponding platform device (which is spawned from the
PRCMU MFD driver).
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Daniel Lezcano <daniel.lezcano@linaro.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm
Pull power management and ACPI updates from Rafael Wysocki:
"This time the total number of ACPI commits is slightly greater than
the number of cpufreq commits, but Viresh Kumar (who works on cpufreq)
remains the most active patch submitter.
To me, the most significant change is the addition of offline/online
device operations to the driver core (with the Greg's blessing) and
the related modifications of the ACPI core hotplug code. Next are the
freezer updates from Colin Cross that should make the freezing of
tasks a bit less heavy weight.
We also have a couple of regression fixes, a number of fixes for
issues that have not been identified as regressions, two new drivers
and a bunch of cleanups all over.
Highlights:
- Hotplug changes to support graceful hot-removal failures.
It sometimes is necessary to fail device hot-removal operations
gracefully if they cannot be carried out completely. For example,
if memory from a memory module being hot-removed has been allocated
for the kernel's own use and cannot be moved elsewhere, it's
desirable to fail the hot-removal operation in a graceful way
rather than to crash the kernel, but currenty a success or a kernel
crash are the only possible outcomes of an attempted memory
hot-removal. Needless to say, that is not a very attractive
alternative and it had to be addressed.
However, in order to make it work for memory, I first had to make
it work for CPUs and for this purpose I needed to modify the ACPI
processor driver. It's been split into two parts, a resident one
handling the low-level initialization/cleanup and a modular one
playing the actual driver's role (but it binds to the CPU system
device objects rather than to the ACPI device objects representing
processors). That's been sort of like a live brain surgery on a
patient who's riding a bike.
So this is a little scary, but since we found and fixed a couple of
regressions it caused to happen during the early linux-next testing
(a month ago), nobody has complained.
As a bonus we remove some duplicated ACPI hotplug code, because the
ACPI-based CPU hotplug is now going to use the common ACPI hotplug
code.
- Lighter weight freezing of tasks.
These changes from Colin Cross and Mandeep Singh Baines are
targeted at making the freezing of tasks a bit less heavy weight
operation. They reduce the number of tasks woken up every time
during the freezing, by using the observation that the freezer
simply doesn't need to wake up some of them and wait for them all
to call refrigerator(). The time needed for the freezer to decide
to report a failure is reduced too.
Also reintroduced is the check causing a lockdep warining to
trigger when try_to_freeze() is called with locks held (which is
generally unsafe and shouldn't happen).
- cpufreq updates
First off, a commit from Srivatsa S Bhat fixes a resume regression
introduced during the 3.10 cycle causing some cpufreq sysfs
attributes to return wrong values to user space after resume. The
fix is kind of fresh, but also it's pretty obvious once Srivatsa
has identified the root cause.
Second, we have a new freqdomain_cpus sysfs attribute for the
acpi-cpufreq driver to provide information previously available via
related_cpus. From Lan Tianyu.
Finally, we fix a number of issues, mostly related to the
CPUFREQ_POSTCHANGE notifier and cpufreq Kconfig options and clean
up some code. The majority of changes from Viresh Kumar with bits
from Jacob Shin, Heiko Stübner, Xiaoguang Chen, Ezequiel Garcia,
Arnd Bergmann, and Tang Yuantian.
- ACPICA update
A usual bunch of updates from the ACPICA upstream.
During the 3.4 cycle we introduced support for ACPI 5 extended
sleep registers, but they are only supposed to be used if the
HW-reduced mode bit is set in the FADT flags and the code attempted
to use them without checking that bit. That caused suspend/resume
regressions to happen on some systems. Fix from Lv Zheng causes
those registers to be used only if the HW-reduced mode bit is set.
Apart from this some other ACPICA bugs are fixed and code cleanups
are made by Bob Moore, Tomasz Nowicki, Lv Zheng, Chao Guan, and
Zhang Rui.
- cpuidle updates
New driver for Xilinx Zynq processors is added by Michal Simek.
Multidriver support simplification, addition of some missing
kerneldoc comments and Kconfig-related fixes come from Daniel
Lezcano.
- ACPI power management updates
Changes to make suspend/resume work correctly in Xen guests from
Konrad Rzeszutek Wilk, sparse warning fix from Fengguang Wu and
cleanups and fixes of the ACPI device power state selection
routine.
- ACPI documentation updates
Some previously missing pieces of ACPI documentation are added by
Lv Zheng and Aaron Lu (hopefully, that will help people to
uderstand how the ACPI subsystem works) and one outdated doc is
updated by Hanjun Guo.
- Assorted ACPI updates
We finally nailed down the IA-64 issue that was the reason for
reverting commit 9f29ab11ddbf ("ACPI / scan: do not match drivers
against objects having scan handlers"), so we can fix it and move
the ACPI scan handler check added to the ACPI video driver back to
the core.
A mechanism for adding CMOS RTC address space handlers is
introduced by Lan Tianyu to allow some EC-related breakage to be
fixed on some systems.
A spec-compliant implementation of acpi_os_get_timer() is added by
Mika Westerberg.
The evaluation of _STA is added to do_acpi_find_child() to avoid
situations in which a pointer to a disabled device object is
returned instead of an enabled one with the same _ADR value. From
Jeff Wu.
Intel BayTrail PCH (Platform Controller Hub) support is added to
the ACPI driver for Intel Low-Power Subsystems (LPSS) and that
driver is modified to work around a couple of known BIOS issues.
Changes from Mika Westerberg and Heikki Krogerus.
The EC driver is fixed by Vasiliy Kulikov to use get_user() and
put_user() instead of dereferencing user space pointers blindly.
Code cleanups are made by Bjorn Helgaas, Nicholas Mazzuca and Toshi
Kani.
- Assorted power management updates
The "runtime idle" helper routine is changed to take the return
values of the callbacks executed by it into account and to call
rpm_suspend() if they return 0, which allows us to reduce the
overall code bloat a bit (by dropping some code that's not
necessary any more after that modification).
The runtime PM documentation is updated by Alan Stern (to reflect
the "runtime idle" behavior change).
New trace points for PM QoS are added by Sahara
(<keun-o.park@windriver.com>).
PM QoS documentation is updated by Lan Tianyu.
Code cleanups are made and minor issues are addressed by Bernie
Thompson, Bjorn Helgaas, Julius Werner, and Shuah Khan.
- devfreq updates
New driver for the Exynos5-bus device from Abhilash Kesavan.
Minor cleanups, fixes and MAINTAINERS update from MyungJoo Ham,
Abhilash Kesavan, Paul Bolle, Rajagopal Venkat, and Wei Yongjun.
- OMAP power management updates
Adaptive Voltage Scaling (AVS) SmartReflex voltage control driver
updates from Andrii Tseglytskyi and Nishanth Menon."
* tag 'pm+acpi-3.11-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/rafael/linux-pm: (162 commits)
cpufreq: Fix cpufreq regression after suspend/resume
ACPI / PM: Fix possible NULL pointer deref in acpi_pm_device_sleep_state()
PM / Sleep: Warn about system time after resume with pm_trace
cpufreq: don't leave stale policy pointer in cdbs->cur_policy
acpi-cpufreq: Add new sysfs attribute freqdomain_cpus
cpufreq: make sure frequency transitions are serialized
ACPI: implement acpi_os_get_timer() according the spec
ACPI / EC: Add HP Folio 13 to ec_dmi_table in order to skip DSDT scan
ACPI: Add CMOS RTC Operation Region handler support
ACPI / processor: Drop unused variable from processor_perflib.c
cpufreq: tegra: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: s3c64xx: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: omap: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: imx6q: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: exynos: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: dbx500: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: davinci: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: arm-big-little: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: powernow-k8: call CPUFREQ_POSTCHANGE notfier in error cases
cpufreq: pcc: call CPUFREQ_POSTCHANGE notfier in error cases
...
|
|
BML clock register address in DB8580 has changed.Defined a new address
under different name for DB8580.
Signed-off-by: Philippe Begnic <philippe.begnic@st.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Mike Turquette <mturquette@linaro.org>
|
|
The "index" field of struct cpufreq_frequency_table was never an
index and isn't used at all by the cpufreq core. It only is useful
for cpufreq drivers for their internal purposes.
Many people nowadays blindly set it in ascending order with the
assumption that the core will use it, which is a mistake.
Rename it to "driver_data" as that's what its purpose is. All of its
users are updated accordingly.
[rjw: Changelog]
Signed-off-by: Viresh Kumar <viresh.kumar@linaro.org>
Acked-by: Simon Horman <horms+renesas@verge.net.au>
Signed-off-by: Rafael J. Wysocki <rafael.j.wysocki@intel.com>
|
|
Previously the DSI PLL divider rate was initialised statically and
assumed to be 1. Before the common clock framework was enabled for
ux500, a call to clk_set_rate() would always update the HW registers
no matter what the current setting was.
This patch makes sure the actual hw settings and the sw assumed
settings are matched.
Signed-off-by: Paer-Olof Haakansson <par-olof.hakansson@stericsson.com>
Signed-off-by: Ulf Hansson <ulf.hansson@linaro.org>
signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The MFD subsystem requires drivers to state the size of any platform
data passed, or it will fail to assign it to the device. This will
culminate in a NULL platform_data attribute and normally a failure to
probe() or a kernel Oops.
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
The main aim for this cycle is to have the u8540 booting to a
console. However, the u8540 doesn't support all of the u8500
platform devices yet. After this stage is complete we can then
fill in the inadequacies, such as specific clock support at a
later date. To achieve this we're placing devices supported by
all platforms into a common device structure and the remaining
ones into a platform specific one.
Cc: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
Currently we check to see if we obtained the Tightly Coupled Program
Memory (TCPM) base and only execute the code within the check if we
have it. It's more traditional to return early if we don't have it.
This way we can flatten most of the function's code down to a single
tab spacing.
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Samuel Ortiz <sameo@linux.intel.com>
|
|
This untangles the final bits of the prcmu code from the platform
code:
* The IRQ_PRCMU_* definitions move from irqs-db8500.h into prcmu.c
because they are only of local significance.
* u8500_thsens_device goes into the prcmu, because it uses a PRCMU
IRQ that the platform does not see.
* IRQ_DB8500_AB8500 and IRQ_PRCMU_BASE go into the platform data
because the PRCMU does not see it.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
[Fixed a oneliner bug]
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
These two <mach/*> includes are no longer used in the
PRCMU driver, so drop them.
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We are trying to decompose and decentralize the code in
the DB8500 PRCMU out into subdrivers. The code moved in
this patch concerns a group of functions used for
decoupling and recoupling the IRQs from the GIC. During
sleep and idle the Ux500 system will transfer all IRQ
handling to the PRCMU using these functions.
Basically we are left with the two alternatives of code
placement as:
- arch/arm/mach-ux500/pm.c - this because the code is
closely related to the GIC, and takes ownership of
some of the registers from the PRCMU related to this
PM functionality.
- drivers/mfd/db8500-prcmu-pm.c - because the code is
affecting stuff in the PRCMU register range. But then
this code needs to remap and handle GIC registers.
This patch implementation is taking the first approach.
Currently the cpuidle driver is the only piece of code
using this set of functions, but it will later also be
used by the suspend/resume code which is currently under
review.
The header file is moved to:
<linux/platform_data/arm-ux500-pm.h>
The function prototypes need to be placed in a globally
visible header since the CPUidle code is planned to move
out to drivers/cpuidle.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Rickard Andersson <rickard.andersson@stericsson.com>
Acked-by: Daniel Lezcano <daniel.lezcano@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
We cannot use a global variable stored in <mach/hardware.h> to
find the base address of the PRCMU. The real resource is already
there from the board, so use this to look up the base address
instead.
Currently the patch is kept minimal so as not to interfere with
other work being done on refactoring this driver, but at a later
point the defines using (prcmu_base + 0xnnn) need to be replaced
by pure offset defined for (0xnnn) and the base inlined with the
readl()/writel() and similar codepaths.
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
This patch will make an early remapping of the PRCMU, to be
used when setting up the clocks, that will call down into parts
of the PRCMU driver before it is probed.
Going forward this will be removed like this:
- The mailbox subsystem need to be merged.
http://marc.info/?l=linux-kernel&m=136314559201983&w=2
- At this point the PRCMU clock code can be moved over to the
ux500 clock driver in drivers/clk/ux500/* and maintained
there in a decentralized manner.
- This early initcall and PRCMU base parameters become part of
the ux500_clk_init() call instead.
Cc: Suman Anna <s-anna@ti.com>
Cc: Loic Pallardy <loic.pallardy@st.com>
Acked-by: Samuel Ortiz <sameo@linux.intel.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Ulf Hansson <ulf.hansson@linaro.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
