| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Some of the larger changes this merge window:
- Removal of drivers for Exynos5440, a Samsung SoC that never saw
widespread use.
- Uniphier support for USB3 and SPI reset handling
- Syste control and SRAM drivers and bindings for Allwinner platforms
- Qualcomm AOSS (Always-on subsystem) reset controller drivers
- Raspberry Pi hwmon driver for voltage
- Mediatek pwrap (pmic) support for MT6797 SoC"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (52 commits)
drivers/firmware: psci_checker: stash and use topology_core_cpumask for hotplug tests
soc: fsl: cleanup Kconfig menu
soc: fsl: dpio: Convert DPIO documentation to .rst
staging: fsl-mc: Remove remaining files
staging: fsl-mc: Move DPIO from staging to drivers/soc/fsl
staging: fsl-dpaa2: eth: move generic FD defines to DPIO
soc: fsl: qe: gpio: Add qe_gpio_set_multiple
usb: host: exynos: Remove support for Exynos5440
clk: samsung: Remove support for Exynos5440
soc: sunxi: Add the A13, A23 and H3 system control compatibles
reset: uniphier: add reset control support for SPI
cpufreq: exynos: Remove support for Exynos5440
ata: ahci-platform: Remove support for Exynos5440
soc: imx6qp: Use GENPD_FLAG_ALWAYS_ON for PU errata
soc: mediatek: pwrap: add mt6351 driver for mt6797 SoCs
soc: mediatek: pwrap: add pwrap driver for mt6797 SoCs
soc: mediatek: pwrap: fix cipher init setting error
dt-bindings: pwrap: mediatek: add pwrap support for MT6797
reset: uniphier: add USB3 core reset control
dt-bindings: reset: uniphier: add USB3 core reset support
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here is the bit set of char/misc drivers for 4.19-rc1
There is a lot here, much more than normal, seems like everyone is
writing new driver subsystems these days... Anyway, major things here
are:
- new FSI driver subsystem, yet-another-powerpc low-level hardware
bus
- gnss, finally an in-kernel GPS subsystem to try to tame all of the
crazy out-of-tree drivers that have been floating around for years,
combined with some really hacky userspace implementations. This is
only for GNSS receivers, but you have to start somewhere, and this
is great to see.
Other than that, there are new slimbus drivers, new coresight drivers,
new fpga drivers, and loads of DT bindings for all of these and
existing drivers.
All of these have been in linux-next for a while with no reported
issues"
* tag 'char-misc-4.19-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (255 commits)
android: binder: Rate-limit debug and userspace triggered err msgs
fsi: sbefifo: Bump max command length
fsi: scom: Fix NULL dereference
misc: mic: SCIF Fix scif_get_new_port() error handling
misc: cxl: changed asterisk position
genwqe: card_base: Use true and false for boolean values
misc: eeprom: assignment outside the if statement
uio: potential double frees if __uio_register_device() fails
eeprom: idt_89hpesx: clean up an error pointer vs NULL inconsistency
misc: ti-st: Fix memory leak in the error path of probe()
android: binder: Show extra_buffers_size in trace
firmware: vpd: Fix section enabled flag on vpd_section_destroy
platform: goldfish: Retire pdev_bus
goldfish: Use dedicated macros instead of manual bit shifting
goldfish: Add missing includes to goldfish.h
mux: adgs1408: new driver for Analog Devices ADGS1408/1409 mux
dt-bindings: mux: add adi,adgs1408
Drivers: hv: vmbus: Cleanup synic memory free path
Drivers: hv: vmbus: Remove use of slow_virt_to_phys()
Drivers: hv: vmbus: Reset the channel callback in vmbus_onoffer_rescind()
...
|
|
JZ4780_NEMC doesn't depend on OF, and if OF isn't enabled we get this
error:
drivers/memory/jz4780-nemc.c: In function ‘jz4780_nemc_num_banks’:
drivers/memory/jz4780-nemc.c:72:10: error: implicit declaration of
function ‘of_read_number’; did you mean ‘down_read_nested’?
[-Werror=implicit-function-declaration]
bank = of_read_number(prop, 1);
^~~~~~~~~~~~~~
down_read_nested
Make JZ4780_NEMC depend on OF.
Fixes: ab99e11062c1 ("memory: jz4780-nemc: Allow selection of this driver when COMPILE_TEST=y")
Reported-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Acked-by: Randy Dunlap <rdunlap@infradead.org>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It just makes maintainers' life easier by allowing them to compile-test
this driver without having MACH_JZ4780 enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Acked-by: Paul Burton <paul.burton@mips.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
It just makes maintainers' life easier by allowing them to compile-test
this driver without having FSL_SOC, ARCH_LAYERSCAPE or SOC_LS1021A
enabled.
We also need to add a dependency on HAS_IOMEM to make sure the
driver compiles correctly.
Signed-off-by: Boris Brezillon <boris.brezillon@bootlin.com>
Signed-off-by: Miquel Raynal <miquel.raynal@bootlin.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
memory: tegra: Changes for v4.19-rc1
This contains a single fix for the initialization order of the various
parts of the Tegra memory controller driver.
* tag 'tegra-for-4.19-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: Correct driver probe order
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
The Reset Controller should be registered in the end of probe, otherwise
Memory Controller device goes away if IRQ requesting fails and the Reset
Controller stays registered. To avoid having to unwind the MC probing in
a case of SMMU probe failure, let's simply print the error message without
failing the MC probe. This allows us to just move the Reset Controller
registering before the SMMU registration, reducing code churning. Also
let's not fail MC probe in a case of Reset Controller registration failure
as it doesn't prevent the MC driver to work.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
At over 4000 #includes, <linux/platform_device.h> is the 9th most
#included header file in the Linux kernel. It does not need
<linux/mod_devicetable.h>, so drop that header and explicitly add
<linux/mod_devicetable.h> to source files that need it.
4146 #include <linux/platform_device.h>
After this patch, there are 225 files that use <linux/mod_devicetable.h>,
for a reduction of around 3900 times that <linux/mod_devicetable.h>
does not have to be read & parsed.
225 #include <linux/mod_devicetable.h>
This patch was build-tested on 20 different arch-es.
It also makes these drivers SubmitChecklist#1 compliant.
Signed-off-by: Randy Dunlap <rdunlap@infradead.org>
Reported-by: kbuild test robot <lkp@intel.com> # drivers/media/platform/vimc/
Reported-by: kbuild test robot <lkp@intel.com> # drivers/pinctrl/pinctrl-u300.c
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
After an RTC+DDR cycle we lose sram context so emif pm functions present
in sram are lost. We can check if the first byte of the original
code in DDR contains the same first byte as the code in sram, and if
they do not match we know we have lost context and must recopy the
functions to the previous address to maintain PM functionality.
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Keerthy <j-keerthy@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux
Pull more overflow updates from Kees Cook:
"The rest of the overflow changes for v4.18-rc1.
This includes the explicit overflow fixes from Silvio, further
struct_size() conversions from Matthew, and a bug fix from Dan.
But the bulk of it is the treewide conversions to use either the
2-factor argument allocators (e.g. kmalloc(a * b, ...) into
kmalloc_array(a, b, ...) or the array_size() macros (e.g. vmalloc(a *
b) into vmalloc(array_size(a, b)).
Coccinelle was fighting me on several fronts, so I've done a bunch of
manual whitespace updates in the patches as well.
Summary:
- Error path bug fix for overflow tests (Dan)
- Additional struct_size() conversions (Matthew, Kees)
- Explicitly reported overflow fixes (Silvio, Kees)
- Add missing kvcalloc() function (Kees)
- Treewide conversions of allocators to use either 2-factor argument
variant when available, or array_size() and array3_size() as needed
(Kees)"
* tag 'overflow-v4.18-rc1-part2' of git://git.kernel.org/pub/scm/linux/kernel/git/kees/linux: (26 commits)
treewide: Use array_size in f2fs_kvzalloc()
treewide: Use array_size() in f2fs_kzalloc()
treewide: Use array_size() in f2fs_kmalloc()
treewide: Use array_size() in sock_kmalloc()
treewide: Use array_size() in kvzalloc_node()
treewide: Use array_size() in vzalloc_node()
treewide: Use array_size() in vzalloc()
treewide: Use array_size() in vmalloc()
treewide: devm_kzalloc() -> devm_kcalloc()
treewide: devm_kmalloc() -> devm_kmalloc_array()
treewide: kvzalloc() -> kvcalloc()
treewide: kvmalloc() -> kvmalloc_array()
treewide: kzalloc_node() -> kcalloc_node()
treewide: kzalloc() -> kcalloc()
treewide: kmalloc() -> kmalloc_array()
mm: Introduce kvcalloc()
video: uvesafb: Fix integer overflow in allocation
UBIFS: Fix potential integer overflow in allocation
leds: Use struct_size() in allocation
Convert intel uncore to struct_size
...
|
|
The devm_kzalloc() function has a 2-factor argument form, devm_kcalloc().
This patch replaces cases of:
devm_kzalloc(handle, a * b, gfp)
with:
devm_kcalloc(handle, a * b, gfp)
as well as handling cases of:
devm_kzalloc(handle, a * b * c, gfp)
with:
devm_kzalloc(handle, array3_size(a, b, c), gfp)
as it's slightly less ugly than:
devm_kcalloc(handle, array_size(a, b), c, gfp)
This does, however, attempt to ignore constant size factors like:
devm_kzalloc(handle, 4 * 1024, gfp)
though any constants defined via macros get caught up in the conversion.
Any factors with a sizeof() of "unsigned char", "char", and "u8" were
dropped, since they're redundant.
Some manual whitespace fixes were needed in this patch, as Coccinelle
really liked to write "=devm_kcalloc..." instead of "= devm_kcalloc...".
The Coccinelle script used for this was:
// Fix redundant parens around sizeof().
@@
expression HANDLE;
type TYPE;
expression THING, E;
@@
(
devm_kzalloc(HANDLE,
- (sizeof(TYPE)) * E
+ sizeof(TYPE) * E
, ...)
|
devm_kzalloc(HANDLE,
- (sizeof(THING)) * E
+ sizeof(THING) * E
, ...)
)
// Drop single-byte sizes and redundant parens.
@@
expression HANDLE;
expression COUNT;
typedef u8;
typedef __u8;
@@
(
devm_kzalloc(HANDLE,
- sizeof(u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * (COUNT)
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(__u8) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(char) * COUNT
+ COUNT
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(unsigned char) * COUNT
+ COUNT
, ...)
)
// 2-factor product with sizeof(type/expression) and identifier or constant.
@@
expression HANDLE;
type TYPE;
expression THING;
identifier COUNT_ID;
constant COUNT_CONST;
@@
(
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_ID)
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_ID
+ COUNT_ID, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (COUNT_CONST)
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * COUNT_CONST
+ COUNT_CONST, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_ID)
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_ID
+ COUNT_ID, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (COUNT_CONST)
+ COUNT_CONST, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * COUNT_CONST
+ COUNT_CONST, sizeof(THING)
, ...)
)
// 2-factor product, only identifiers.
@@
expression HANDLE;
identifier SIZE, COUNT;
@@
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- SIZE * COUNT
+ COUNT, SIZE
, ...)
// 3-factor product with 1 sizeof(type) or sizeof(expression), with
// redundant parens removed.
@@
expression HANDLE;
expression THING;
identifier STRIDE, COUNT;
type TYPE;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(TYPE))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * (COUNT) * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * (STRIDE)
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING) * COUNT * STRIDE
+ array3_size(COUNT, STRIDE, sizeof(THING))
, ...)
)
// 3-factor product with 2 sizeof(variable), with redundant parens removed.
@@
expression HANDLE;
expression THING1, THING2;
identifier COUNT;
type TYPE1, TYPE2;
@@
(
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(TYPE2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(TYPE2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(THING1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(THING1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * COUNT
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
|
devm_kzalloc(HANDLE,
- sizeof(TYPE1) * sizeof(THING2) * (COUNT)
+ array3_size(COUNT, sizeof(TYPE1), sizeof(THING2))
, ...)
)
// 3-factor product, only identifiers, with redundant parens removed.
@@
expression HANDLE;
identifier STRIDE, SIZE, COUNT;
@@
(
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * STRIDE * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- (COUNT) * (STRIDE) * (SIZE)
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
|
devm_kzalloc(HANDLE,
- COUNT * STRIDE * SIZE
+ array3_size(COUNT, STRIDE, SIZE)
, ...)
)
// Any remaining multi-factor products, first at least 3-factor products,
// when they're not all constants...
@@
expression HANDLE;
expression E1, E2, E3;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE,
- (E1) * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * E3
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- (E1) * (E2) * (E3)
+ array3_size(E1, E2, E3)
, ...)
|
devm_kzalloc(HANDLE,
- E1 * E2 * E3
+ array3_size(E1, E2, E3)
, ...)
)
// And then all remaining 2 factors products when they're not all constants,
// keeping sizeof() as the second factor argument.
@@
expression HANDLE;
expression THING, E1, E2;
type TYPE;
constant C1, C2, C3;
@@
(
devm_kzalloc(HANDLE, sizeof(THING) * C2, ...)
|
devm_kzalloc(HANDLE, sizeof(TYPE) * C2, ...)
|
devm_kzalloc(HANDLE, C1 * C2 * C3, ...)
|
devm_kzalloc(HANDLE, C1 * C2, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * (E2)
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(TYPE) * E2
+ E2, sizeof(TYPE)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * (E2)
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- sizeof(THING) * E2
+ E2, sizeof(THING)
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * E2
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- (E1) * (E2)
+ E1, E2
, ...)
|
- devm_kzalloc
+ devm_kcalloc
(HANDLE,
- E1 * E2
+ E1, E2
, ...)
)
Signed-off-by: Kees Cook <keescook@chromium.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
memory: tegra: Changes for v4.18-rc1
This contains some cleanup of the memory controller driver as well as
unification work to share more code between Tegra20 and later SoC
generations. Also included are an implementation for the hot resets
functionality by the memory controller which is required to properly
reset busy hardware.
* tag 'tegra-for-4.18-memory-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
dt-bindings: memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Remove Tegra114 SATA and AFI reset definitions
memory: tegra: Register SMMU after MC driver became ready
memory: tegra: Add Tegra210 memory controller hot resets
memory: tegra: Add Tegra124 memory controller hot resets
memory: tegra: Add Tegra114 memory controller hot resets
memory: tegra: Add Tegra30 memory controller hot resets
memory: tegra: Add Tegra20 memory controller hot resets
memory: tegra: Introduce memory client hot reset
memory: tegra: Squash tegra20-mc into common tegra-mc driver
memory: tegra: Remove unused headers inclusions
memory: tegra: Apply interrupts mask per SoC
memory: tegra: Setup interrupts mask before requesting IRQ
memory: tegra: Do not handle spurious interrupts
dt-bindings: memory: tegra: Add hot resets definitions
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Tegra114 doesn't have SATA nor PCIe, but TRM seems erroneously document
them.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Memory Controller driver invokes SMMU driver registration and MC's
registers mapping is shared with SMMU. This mapping goes away if MC
driver probing fails after SMMU registration.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
into next/drivers
This pull request contains Broadcom ARM/ARM64/MIPS SoCs drivers changes
for 4.18, please pull the following:
- Florian removes the synthetic struct device in the DPFE driver which
was used to attach sysfs attributes and uses the platform_device we are
probed from instead.
* tag 'arm-soc/for-4.18/drivers' of https://github.com/Broadcom/stblinux:
memory: brcmstb: dpfe: Remove need for dpfe_dev
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/drivers
OMAP-GPMC: driver updates for v4.18
* get rid of a redundant NULL check in gpmc_probe_dt_children()
* tag 'gpmc-omap-for-v4.18' of https://github.com/rogerq/linux:
memory: omap-gpmc: Avoid redundant NULL check
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
ARM: SOC driver update for 4.18
- AEMIF driver update to support board files and remove
need of mach-davinci aemif code
- Use percpu counters for qmss datapath stats
- License update for TI SCI
* tag 'soc_drivers_for_4.18' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
firmware: ti_sci: Switch to SPDX Licensing
soc: ti: knav_qmss: Use percpu instead atomic for stats counter
memory: aemif: add support for board files
memory: aemif: don't rely on kbuild for driver's name
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
We can hook sysfs objects to the parent platform device that we are
created from, no need to have a synthetic dpfe_dev just for that. This
incidentally removes the need for having an index, since we are
guaranteed to have an unique path in the sysfs hiearchy.
Acked-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Define the table of memory controller hot resets for Tegra210.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Define the table of memory controller hot resets for Tegra124.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Define the table of memory controller hot resets for Tegra114.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Define the table of memory controller hot resets for Tegra30.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Define the table of memory controller hot resets for Tegra20 and add
specific to Tegra20 hot reset operations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to reset busy HW properly, memory controller needs to be
involved, otherwise it is possible to get corrupted memory or hang machine
if HW was reset during DMA. Introduce memory client 'hot reset' that will
be used for resetting of busy HW.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra30+ has some minor differences in registers / bits layout compared
to Tegra20. Let's squash Tegra20 driver into the common tegra-mc driver
in a preparation for the upcoming MC hot reset controls implementation,
avoiding code duplication.
Note that this currently doesn't report the value of MC_GART_ERROR_REQ
because it is located within the GART register area and cannot be safely
accessed from the MC driver (this happens to work only by accident). The
proper solution is to integrate the GART driver with the MC driver, much
like is done for the Tegra SMMU, but that is an invasive change and will
be part of a separate patch series.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra210 contains some unused leftover headers, remove them for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently we are enabling handling of interrupts specific to Tegra124+
which happen to overlap with previous generations. Let's specify
interrupts mask per SoC generation for consistency and in a preparation
of squashing of Tegra20 driver into the common one that will enable
handling of GART faults which may be undesirable by newer generations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This avoids unwanted interrupt during MC driver probe.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ISR reads interrupts-enable mask, but doesn't utilize it. Apply the
mask to the interrupt status and don't handle interrupts that MC driver
haven't asked for. Kernel would disable spurious MC IRQ and report the
error. This would happen only in a case of a very severe bug.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
child->name cannot be NULL as we're already checking for it
in gpmc_probe_dt_children()
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Currently aemif is supported in two places separately. By the platform
driver in drivers/memory and by a hand crafted driver in mach-davinci.
We want to drop the latter but also keep the legacy mode. Add support
for board files to the aemif driver.
The new structure in platform data currently only contains the chip
select number, since currently existing users don't require anything
else, but it can be extended in the future.
While extending the platform data struct, add kernel docs describing
its members.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
We want to use aemif from board files. Use a static name in the
driver's code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The sleep33xx and sleep43xx files should not depend on a header file
generated in drivers/memory. Remove this dependency and instead allow
both drivers/memory and arch/arm/mach-omap2 to generate all macros
needed in headers local to their own paths.
This fixes an issue where the build fail will when using O= to set a
split object directory and arch/arm/mach-omap2 is built before
drivers/memory with the following error:
.../drivers/memory/emif-asm-offsets.c:1:0: fatal error: can't open
drivers/memory/emif-asm-offsets.s for writing: No such file or directory
compilation terminated.
Fixes: 41d9d44d7258 ("ARM: OMAP2+: pm33xx-core: Add platform code needed for PM")
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung soc drivers changes for v4.17" from Krzysztof Kozłowski:
1. Add SPDX license identifiers.
2. Populate children syscon nodes in PMU driver to properly model HW in
DeviceTree.
* tag 'samsung-drivers-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Populate children syscon nodes
soc: samsung: Add SPDX license identifiers to headers
memory: samsung: Add SPDX license identifiers
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
Pull "SOC driver changes for v4.17" from Santosh Shilimkar:
- Remove redundant dev_err from probe in ti-emif-srma driver
- Make use of seq_putc in emif reg show
* tag 'soc_drivers_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
memory: ti-emif-sram: remove redundant dev_err call in ti_emif_probe()
memory-EMIF: Use seq_putc() in emif_regdump_show()
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The DCPU can now send message data in two ways:
- via the data RAM, as before (this is now message type 0)
- via the message RAM (this is message type 1)
In order to support both methods, we check the message type of the
response (bits 31:28) and then treat the offset (bits 27:0)
accordingly.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
In some functions, variable "ret" should be ssize_t, so we fix it.
Fixes: 2f330caff577 ("memory: brcmstb: Add driver for DPFE")
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
We were printing the entire 32 bit register rather than just the lower
8 bits. Anything above bit 7 is reserved and may be any random value.
Fixes: 2f330caff577 ("memory: brcmstb: Add driver for DPFE")
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Replace GPL license statements with SPDX GPL-2.0 license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
|
|
Move away from platform data configuration and use pure DT approach.
Use generic probe function to deal with OneNAND node and remove now useless
gpmc_probe_onenand_child function. Import sync mode timing calculation
function from mach-omap2/gpmc-onenand.c
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
SOC: Keystone Soc driver updates for 4.16
- TI EMIF-SRAM driver
- TI SCI print format fix
- Navigator strndup lenth fix
* tag 'keystone_driver_soc_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: fix max dup length for kstrndup
firmware: ti_sci: Use %zu for size_t print format
memory: ti-emif-sram: remove unused variable
memory: ti-emif-sram: introduce relocatable suspend/resume handlers
Documentation: dt: Update ti,emif bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "memory: tegra: Changes for v4.16-rc1" from Thierry Reding:
The Tegra memory controller driver will now instruct the SMMU driver to
create groups, which will make it easier for device drivers to share an
IOMMU domain between multiple devices.
Initial Tegra186 support is also added in a separate driver.
* tag 'tegra-for-4.16-memory' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
iommu/tegra-smmu: Fix return value check in tegra_smmu_group_get()
iommu/tegra: Allow devices to be grouped
memory: tegra: Create SMMU display groups
memory: tegra: Add Tegra186 support
dt-bindings: memory: Add Tegra186 support
dt-bindings: misc: Add Tegra186 MISC registers bindings
|
|
Create SMMU display groups for Tegra30, Tegra114, Tegra124 and Tegra210.
This allows the display controllers on these devices to share the same
IOMMU domain using the standard IOMMU group mechanism.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The memory controller found on Tegra186 is different in some respects to
its predecessors. Most notably it no longer implements an SMMU, but does
assign ARM SMMU stream IDs for each memory client instead.
Provide a driver that programs these registers so that memory clients
can translate addresses via the ARM SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The newly introduced driver causes a harmless warning for a variable
that was evidently never used:
drivers/memory/ti-emif-pm.c: In function 'ti_emif_remove':
drivers/memory/ti-emif-pm.c:303:17: error: unused variable 'dev' [-Werror=unused-variable]
Fixes: 8428e5ad750d ("memory: ti-emif-sram: introduce relocatable suspend/resume handlers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Certain SoCs like Texas Instruments AM335x and AM437x require parts
of the EMIF PM code to run late in the suspend sequence from SRAM,
such as saving and restoring the EMIF context and placing the memory
into self-refresh.
One requirement for these SoCs to suspend and enter its lowest power
mode, called DeepSleep0, is that the PER power domain must be shut off.
Because the EMIF (DDR Controller) resides within this power domain, it
will lose context during a suspend operation, so we must save it so we
can restore once we resume. However, we cannot execute this code from
external memory, as it is not available at this point, so the code must
be executed late in the suspend path from SRAM.
This patch introduces a ti-emif-sram driver that includes several
functions written in ARM ASM that are relocatable so the PM SRAM
code can use them. It also allocates a region of writable SRAM to
be used by the code running in the executable region of SRAM to save
and restore the EMIF context. It can export a table containing the
absolute addresses of the available PM functions so that other SRAM
code can branch to them. This code is required for suspend/resume on
AM335x and AM437x to work.
In addition to this, to be able to share data structures between C and
the ti-emif-sram-pm assembly code, we can automatically generate all of
the C struct member offsets and sizes as macros by processing
emif-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Error out only if both 'bank-width' and 'gpmc,device-width' are missing.
As 'bank-width' is mostly used for NOR devices and all other devices must
use 'gpmc,device-width' update the error message accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
