| Age | Commit message (Collapse) | Author |
|---|
|
Define the table of memory controller hot resets for Tegra20 and add
specific to Tegra20 hot reset operations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
In order to reset busy HW properly, memory controller needs to be
involved, otherwise it is possible to get corrupted memory or hang machine
if HW was reset during DMA. Introduce memory client 'hot reset' that will
be used for resetting of busy HW.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra30+ has some minor differences in registers / bits layout compared
to Tegra20. Let's squash Tegra20 driver into the common tegra-mc driver
in a preparation for the upcoming MC hot reset controls implementation,
avoiding code duplication.
Note that this currently doesn't report the value of MC_GART_ERROR_REQ
because it is located within the GART register area and cannot be safely
accessed from the MC driver (this happens to work only by accident). The
proper solution is to integrate the GART driver with the MC driver, much
like is done for the Tegra SMMU, but that is an invasive change and will
be part of a separate patch series.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Tegra210 contains some unused leftover headers, remove them for
consistency.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
Currently we are enabling handling of interrupts specific to Tegra124+
which happen to overlap with previous generations. Let's specify
interrupts mask per SoC generation for consistency and in a preparation
of squashing of Tegra20 driver into the common one that will enable
handling of GART faults which may be undesirable by newer generations.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
This avoids unwanted interrupt during MC driver probe.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The ISR reads interrupts-enable mask, but doesn't utilize it. Apply the
mask to the interrupt status and don't handle interrupts that MC driver
haven't asked for. Kernel would disable spurious MC IRQ and report the
error. This would happen only in a case of a very severe bug.
Signed-off-by: Dmitry Osipenko <digetx@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
child->name cannot be NULL as we're already checking for it
in gpmc_probe_dt_children()
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Currently aemif is supported in two places separately. By the platform
driver in drivers/memory and by a hand crafted driver in mach-davinci.
We want to drop the latter but also keep the legacy mode. Add support
for board files to the aemif driver.
The new structure in platform data currently only contains the chip
select number, since currently existing users don't require anything
else, but it can be extended in the future.
While extending the platform data struct, add kernel docs describing
its members.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
We want to use aemif from board files. Use a static name in the
driver's code.
Signed-off-by: Bartosz Golaszewski <bgolaszewski@baylibre.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The sleep33xx and sleep43xx files should not depend on a header file
generated in drivers/memory. Remove this dependency and instead allow
both drivers/memory and arch/arm/mach-omap2 to generate all macros
needed in headers local to their own paths.
This fixes an issue where the build fail will when using O= to set a
split object directory and arch/arm/mach-omap2 is built before
drivers/memory with the following error:
.../drivers/memory/emif-asm-offsets.c:1:0: fatal error: can't open
drivers/memory/emif-asm-offsets.s for writing: No such file or directory
compilation terminated.
Fixes: 41d9d44d7258 ("ARM: OMAP2+: pm33xx-core: Add platform code needed for PM")
Reviewed-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Acked-by: Santosh Shilimkar <ssantosh@kernel.org>
Signed-off-by: Tony Lindgren <tony@atomide.com>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Pull "Samsung soc drivers changes for v4.17" from Krzysztof Kozłowski:
1. Add SPDX license identifiers.
2. Populate children syscon nodes in PMU driver to properly model HW in
DeviceTree.
* tag 'samsung-drivers-4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Populate children syscon nodes
soc: samsung: Add SPDX license identifiers to headers
memory: samsung: Add SPDX license identifiers
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
Pull "SOC driver changes for v4.17" from Santosh Shilimkar:
- Remove redundant dev_err from probe in ti-emif-srma driver
- Make use of seq_putc in emif reg show
* tag 'soc_drivers_for_4.17' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
memory: ti-emif-sram: remove redundant dev_err call in ti_emif_probe()
memory-EMIF: Use seq_putc() in emif_regdump_show()
|
|
There is a error message within devm_ioremap_resource
already, so remove the dev_err call to avoid redundant
error message.
Signed-off-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
A single character (line break) should be put into a sequence.
Thus use the corresponding function "seq_putc".
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
The DCPU can now send message data in two ways:
- via the data RAM, as before (this is now message type 0)
- via the message RAM (this is message type 1)
In order to support both methods, we check the message type of the
response (bits 31:28) and then treat the offset (bits 27:0)
accordingly.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
In some functions, variable "ret" should be ssize_t, so we fix it.
Fixes: 2f330caff577 ("memory: brcmstb: Add driver for DPFE")
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
We were printing the entire 32 bit register rather than just the lower
8 bits. Anything above bit 7 is reserved and may be any random value.
Fixes: 2f330caff577 ("memory: brcmstb: Add driver for DPFE")
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
Replace GPL license statements with SPDX GPL-2.0 license identifiers.
Signed-off-by: Krzysztof Kozlowski <krzk@kernel.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"A number of new drivers get added this time, along with many
low-priority bugfixes. The most interesting changes by subsystem are:
bus drivers:
- Updates to the Broadcom bus interface driver to support newer SoC
types
- The TI OMAP sysc driver now supports updated DT bindings
memory controllers:
- A new driver for Tegra186 gets added
- A new driver for the ti-emif sram, to allow relocating
suspend/resume handlers there
SoC specific:
- A new driver for Qualcomm QMI, the interface to the modem on MSM
SoCs
- A new driver for power domains on the actions S700 SoC
- A driver for the Xilinx Zynq VCU logicoreIP
reset controllers:
- A new driver for Amlogic Meson-AGX
- various bug fixes
tee subsystem:
- A new user interface got added to enable asynchronous communication
with the TEE supplicant.
- A new method of using user space memory for communication with the
TEE is added"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (84 commits)
of: platform: fix OF node refcount leak
soc: fsl: guts: Add a NULL check for devm_kasprintf()
bus: ti-sysc: Fix smartreflex sysc mask
psci: add CPU_IDLE dependency
soc: xilinx: Fix Kconfig alignment
soc: xilinx: xlnx_vcu: Use bitwise & rather than logical && on clkoutdiv
soc: xilinx: xlnx_vcu: Depends on HAS_IOMEM for xlnx_vcu
soc: bcm: brcmstb: Be multi-platform compatible
soc: brcmstb: biuctrl: exit without warning on non brcmstb platforms
Revert "soc: brcmstb: Only register SoC device on STB platforms"
bus: omap: add MODULE_LICENSE tags
soc: brcmstb: Only register SoC device on STB platforms
tee: shm: Potential NULL dereference calling tee_shm_register()
soc: xilinx: xlnx_vcu: Add Xilinx ZYNQMP VCU logicoreIP init driver
dt-bindings: soc: xilinx: Add DT bindings to xlnx_vcu driver
soc: xilinx: Create folder structure for soc specific drivers
of: platform: populate /firmware/ node from of_platform_default_populate_init()
soc: samsung: Add SPDX license identifiers
soc: qcom: smp2p: Use common error handling code in qcom_smp2p_probe()
tee: shm: don't put_page on null shm->pages
...
|
|
Move away from platform data configuration and use pure DT approach.
Use generic probe function to deal with OneNAND node and remove now useless
gpmc_probe_onenand_child function. Import sync mode timing calculation
function from mach-omap2/gpmc-onenand.c
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Reviewed-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Tested-by: Tony Lindgren <tony@atomide.com>
Tested-by: Aaro Koskinen <aaro.koskinen@iki.fi>
Acked-by: Roger Quadros <rogerq@ti.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone into next/drivers
SOC: Keystone Soc driver updates for 4.16
- TI EMIF-SRAM driver
- TI SCI print format fix
- Navigator strndup lenth fix
* tag 'keystone_driver_soc_for_4.16' of git://git.kernel.org/pub/scm/linux/kernel/git/ssantosh/linux-keystone:
soc: ti: fix max dup length for kstrndup
firmware: ti_sci: Use %zu for size_t print format
memory: ti-emif-sram: remove unused variable
memory: ti-emif-sram: introduce relocatable suspend/resume handlers
Documentation: dt: Update ti,emif bindings
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
Pull "memory: tegra: Changes for v4.16-rc1" from Thierry Reding:
The Tegra memory controller driver will now instruct the SMMU driver to
create groups, which will make it easier for device drivers to share an
IOMMU domain between multiple devices.
Initial Tegra186 support is also added in a separate driver.
* tag 'tegra-for-4.16-memory' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
iommu/tegra-smmu: Fix return value check in tegra_smmu_group_get()
iommu/tegra: Allow devices to be grouped
memory: tegra: Create SMMU display groups
memory: tegra: Add Tegra186 support
dt-bindings: memory: Add Tegra186 support
dt-bindings: misc: Add Tegra186 MISC registers bindings
|
|
Create SMMU display groups for Tegra30, Tegra114, Tegra124 and Tegra210.
This allows the display controllers on these devices to share the same
IOMMU domain using the standard IOMMU group mechanism.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The memory controller found on Tegra186 is different in some respects to
its predecessors. Most notably it no longer implements an SMMU, but does
assign ARM SMMU stream IDs for each memory client instead.
Provide a driver that programs these registers so that memory clients
can translate addresses via the ARM SMMU.
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The newly introduced driver causes a harmless warning for a variable
that was evidently never used:
drivers/memory/ti-emif-pm.c: In function 'ti_emif_remove':
drivers/memory/ti-emif-pm.c:303:17: error: unused variable 'dev' [-Werror=unused-variable]
Fixes: 8428e5ad750d ("memory: ti-emif-sram: introduce relocatable suspend/resume handlers")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Certain SoCs like Texas Instruments AM335x and AM437x require parts
of the EMIF PM code to run late in the suspend sequence from SRAM,
such as saving and restoring the EMIF context and placing the memory
into self-refresh.
One requirement for these SoCs to suspend and enter its lowest power
mode, called DeepSleep0, is that the PER power domain must be shut off.
Because the EMIF (DDR Controller) resides within this power domain, it
will lose context during a suspend operation, so we must save it so we
can restore once we resume. However, we cannot execute this code from
external memory, as it is not available at this point, so the code must
be executed late in the suspend path from SRAM.
This patch introduces a ti-emif-sram driver that includes several
functions written in ARM ASM that are relocatable so the PM SRAM
code can use them. It also allocates a region of writable SRAM to
be used by the code running in the executable region of SRAM to save
and restore the EMIF context. It can export a table containing the
absolute addresses of the available PM functions so that other SRAM
code can branch to them. This code is required for suspend/resume on
AM335x and AM437x to work.
In addition to this, to be able to share data structures between C and
the ti-emif-sram-pm assembly code, we can automatically generate all of
the C struct member offsets and sizes as macros by processing
emif-asm-offsets.c into assembly code and then extracting the relevant
data as is done for the generated platform asm-offsets.h files.
Acked-by: Tony Lindgren <tony@atomide.com>
Acked-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Dave Gerlach <d-gerlach@ti.com>
Signed-off-by: Santosh Shilimkar <santosh.shilimkar@oracle.com>
|
|
Error out only if both 'bank-width' and 'gpmc,device-width' are missing.
As 'bank-width' is mostly used for NOR devices and all other devices must
use 'gpmc,device-width' update the error message accordingly.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"This branch contains platform-related driver updates for ARM and
ARM64, these are the areas that bring the changes:
New drivers:
- driver support for Renesas R-Car V3M (R8A77970)
- power management support for Amlogic GX
- a new driver for the Tegra BPMP thermal sensor
- a new bus driver for Technologic Systems NBUS
Changes for subsystems that prefer to merge through arm-soc:
- the usual updates for reset controller drivers from Philipp Zabel,
with five added drivers for SoCs in the arc, meson, socfpa,
uniphier and mediatek families
- updates to the ARM SCPI and PSCI frameworks, from Sudeep Holla,
Heiner Kallweit and Lorenzo Pieralisi
Changes specific to some ARM-based SoC
- the Freescale/NXP DPAA QBMan drivers from PowerPC can now work on
ARM as well
- several changes for power management on Broadcom SoCs
- various improvements on Qualcomm, Broadcom, Amlogic, Atmel,
Mediatek
- minor Cleanups for Samsung, TI OMAP SoCs"
[ NOTE! This doesn't work without the previous ARM SoC device-tree pull,
because the R8A77970 driver is missing a header file that came from
that pull.
The fact that this got merged afterwards only fixes it at this point,
and bisection of that driver will fail if/when you walk into the
history of that driver. - Linus ]
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (96 commits)
soc: amlogic: meson-gx-pwrc-vpu: fix power-off when powered by bootloader
bus: add driver for the Technologic Systems NBUS
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
soc: qcom: remove unused label
soc: amlogic: gx pm domain: add PM and OF dependencies
drivers/firmware: psci_checker: Add missing destroy_timer_on_stack()
dt-bindings: power: add amlogic meson power domain bindings
soc: amlogic: add Meson GX VPU Domains driver
soc: qcom: Remote filesystem memory driver
dt-binding: soc: qcom: Add binding for rmtfs memory
of: reserved_mem: Accessor for acquiring reserved_mem
of/platform: Generalize /reserved-memory handling
soc: mediatek: pwrap: fix fatal compiler error
soc: mediatek: pwrap: fix compiler errors
arm64: mediatek: cleanup message for platform selection
soc: Allow test-building of MediaTek drivers
soc: mediatek: place Kconfig for all SoC drivers under menu
soc: mediatek: pwrap: add support for MT7622 SoC
soc: mediatek: pwrap: add common way for setup CS timing extenstion
soc: mediatek: pwrap: add MediaTek MT6380 as one slave of pwrap
..
|
|
next/drivers
Pull "OMAP-GPMC: driver updates for v4.15, part 2" from Roger Quadros:
* get rid of unused function gpmc_update_nand_reg().
* tag 'gpmc-omap-for-v4.15-pt2' of https://github.com/rogerq/linux:
memory: omap-gpmc: Remove deprecated gpmc_update_nand_reg()
|
|
Deprecated gpmc_update_nand_reg() is no longer used, remove.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
http://github.com/Broadcom/stblinux into next/drivers
Pull "Broadcom drivers changes for 4.15 (part 2)" from Florian Fainelli:
This pull request contains Broadcom ARM/ARM64/MIPS SoCs changes for 4.15
(second part), please pull the following:
- Markus updates the Broadcom STB DPFE driver to avoid loading the firmware when
unnecessary to accomodate for specific platform restrictions
- Florian adds support for the Broadcom Hurricane 2 SoC iProc PLL clock needed
to get the proper CPU clock frequency
* tag 'arm-soc/for-4.15/drivers-part2' of http://github.com/Broadcom/stblinux:
clk: bcm: Add Broadcom Hurricane 2 clock support
memory: brcmstb: dpfe: skip downloading firmware when possible
memory: brcmstb: dpfe: introduce is_dcpu_enabled()
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
next/drivers
Pull "OMAP-GPMC: driver updates for v4.15" from Roger Quadros:
* get rid of unused field in platform data structure.
* tag 'gpmc-omap-for-v4.15' of https://github.com/rogerq/linux:
memory: omap-gpmc: Drop gpmc_status
|
|
This field is no longer used, drop it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
We want to skip downloading the DPFE firmware from Linux if it was
already downloaded by the boot loader.
The driver now checks if the DCPU is already running and, if so,
whether it can process commands. If the DCPU processes commands
successfully, the driver skips the firmware download step.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
In order to check whether or not the DCPU is running, we introduce
a function called is_dcpu_enabled().
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
This driver allows access to DRAM properties, such as the refresh rate,
via the Broadcom STB DDR PHY Front End (DPFE). The refresh rate can be
used as indirect indicator of the DRAM temperature.
The driver also allows setting of the sampling interval.
Signed-off-by: Markus Mayer <mmayer@broadcom.com>
Signed-off-by: Florian Fainelli <f.fainelli@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"This branch contains platform-related driver updates for ARM and ARM64.
Among them:
- Reset driver updates:
+ New API for dealing with arrays of resets
+ Make unimplemented {de,}assert return success on shared resets
+ MSDKv1 driver
+ Removal of obsolete Gemini reset driver
+ Misc updates for sunxi and Uniphier
- SoC drivers:
+ Platform SoC driver registration on Tegra
+ Shuffle of Qualcomm drivers into a submenu
+ Allwinner A64 support for SRAM
+ Renesas R-Car R3 support
+ Power domains for Rockchip RK3366
- Misc updates and smaller fixes for TEE and memory driver
subsystems"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (54 commits)
firmware: arm_scpi: fix endianness of dev_id in struct dev_pstate_set
soc/tegra: fuse: Add missing semi-colon
soc/tegra: Restrict SoC device registration to Tegra
drivers: soc: sunxi: add support for A64 and its SRAM C
drivers: soc: sunxi: add support for remapping func value to reg value
drivers: soc: sunxi: fix error processing on base address when claiming
dt-bindings: add binding for Allwinner A64 SRAM controller and SRAM C
bus: sunxi-rsb: Enable by default for ARM64
soc/tegra: Register SoC device
firmware: tegra: set drvdata earlier
memory: Convert to using %pOF instead of full_name
soc: Convert to using %pOF instead of full_name
bus: Convert to using %pOF instead of full_name
firmware: Convert to using %pOF instead of full_name
soc: mediatek: add SCPSYS power domain driver for MediaTek MT7622 SoC
soc: mediatek: add header files required for MT7622 SCPSYS dt-binding
soc: mediatek: reduce code duplication of scpsys_probe across all SoCs
dt-bindings: soc: update the binding document for SCPSYS on MediaTek MT7622 SoC
reset: uniphier: add analog amplifiers reset control
reset: uniphier: add video input subsystem reset control
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
"Slightly more changes than usual this time:
- KDump Kernel IOMMU take-over code for AMD IOMMU. The code now tries
to preserve the mappings of the kernel so that master aborts for
devices are avoided. Master aborts cause some devices to fail in
the kdump kernel, so this code makes the dump more likely to
succeed when AMD IOMMU is enabled.
- common flush queue implementation for IOVA code users. The code is
still optional, but AMD and Intel IOMMU drivers had their own
implementation which is now unified.
- finish support for iommu-groups. All drivers implement this feature
now so that IOMMU core code can rely on it.
- finish support for 'struct iommu_device' in iommu drivers. All
drivers now use the interface.
- new functions in the IOMMU-API for explicit IO/TLB flushing. This
will help to reduce the number of IO/TLB flushes when IOMMU drivers
support this interface.
- support for mt2712 in the Mediatek IOMMU driver
- new IOMMU driver for QCOM hardware
- system PM support for ARM-SMMU
- shutdown method for ARM-SMMU-v3
- some constification patches
- various other small improvements and fixes"
* tag 'iommu-updates-v4.14' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (87 commits)
iommu/vt-d: Don't be too aggressive when clearing one context entry
iommu: Introduce Interface for IOMMU TLB Flushing
iommu/s390: Constify iommu_ops
iommu/vt-d: Avoid calling virt_to_phys() on null pointer
iommu/vt-d: IOMMU Page Request needs to check if address is canonical.
arm/tegra: Call bus_set_iommu() after iommu_device_register()
iommu/exynos: Constify iommu_ops
iommu/ipmmu-vmsa: Make ipmmu_gather_ops const
iommu/ipmmu-vmsa: Rereserving a free context before setting up a pagetable
iommu/amd: Rename a few flush functions
iommu/amd: Check if domain is NULL in get_domain() and return -EBUSY
iommu/mediatek: Fix a build warning of BIT(32) in ARM
iommu/mediatek: Fix a build fail of m4u_type
iommu: qcom: annotate PM functions as __maybe_unused
iommu/pamu: Fix PAMU boot crash
memory: mtk-smi: Degrade SMI init to module_init
iommu/mediatek: Enlarge the validate PA range for 4GB mode
iommu/mediatek: Disable iommu clock when system suspend
iommu/mediatek: Move pgtable allocation into domain_alloc
iommu/mediatek: Merge 2 M4U HWs into one iommu domain
...
|
|
For HSMC controller, the register layout depends on the device i.e. the
offset of setup, pulse, cycle, mode and timings registers is not the
same. An helper is added to provide the correct register layout.
Fixes: fe9d7cb22ef3 ("mfd: syscon: atmel-smc: Add new helpers to ease
SMC regs manipulation")
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Ludovic Desroches <ludovic.desroches@microchip.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Nicolas Ferre <nicolas.ferre@microchip.com>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
'arm/mediatek', 'arm/tegra', 'arm/qcom', 'arm/smmu', 'ppc/pamu', 'x86/vt-d', 'x86/amd', 's390' and 'core' into next
|
|
The initialization of MediaTek power manager(SCPSYS) is
builtin_platform_driver, and SMI must depend on power-domain.
Thus, currently subsys_initcall for SMI is unnecessary, SMI will be
always probe defered by power-domain. Degrade it to module_init.
In addition, there are two small changes about the probe sequence:
1) Delete this two lines.
if (!dev->pm_domain)
return -EPROBE_DEFER;
This is not helpful. the platform driver framework guarantee this.
The "dev_pm_domain_attach" in the "platform_drv_probe" will return
EPROBE_DEFER if its powerdomain is not ready.
2) Add the probe-defer for the smi-larb device should waiting for
smi-common.
In mt2712, there are 2 smi-commons, 10 smi-larbs. All will be
probe-defered by the power-domain, there is seldom case that
smi-larb probe done before smi-common. then it will hang like
this:
Unable to handle kernel NULL pointer dereference at virtual address
00000000 pgd = ffffff800a4e0000
[00000000] *pgd=00000000beffe003[ 17.610026] , *pud=00000000beffe003
...
[<ffffff800897fe04>] mtk_smi_enable+0x1c/0xd0
[<ffffff800897fee8>] mtk_smi_larb_get+0x30/0x98
[<ffffff80088edfa8>] mtk_mipicsi0_resume+0x38/0x1b8
[<ffffff8008634f44>] pm_generic_runtime_resume+0x3c/0x58
[<ffffff8008644ff8>] __genpd_runtime_resume+0x38/0x98
[<ffffff8008647434>] genpd_runtime_resume+0x164/0x220
[<ffffff80086372f8>] __rpm_callback+0x78/0xa0
[<ffffff8008637358>] rpm_callback+0x38/0xa0
[<ffffff8008638a4c>] rpm_resume+0x4a4/0x6f8
[<ffffff8008638d04>] __pm_runtime_resume+0x64/0xa0
[<ffffff80088ed05c>] mtk_mipicsi0_probe+0x40c/0xb70
[<ffffff800862cdc0>] platform_drv_probe+0x58/0xc0
[<ffffff800862a514>] driver_probe_device+0x284/0x438
[<ffffff800862a8ac>] __device_attach_driver+0xb4/0x160
[<ffffff8008627d58>] bus_for_each_drv+0x68/0xa8
[<ffffff800862a0a4>] __device_attach+0xd4/0x168
[<ffffff800862a9d4>] device_initial_probe+0x24/0x30
[<ffffff80086291d8>] bus_probe_device+0xa0/0xa8
[<ffffff8008629784>] deferred_probe_work_func+0x94/0xf0
[<ffffff80080f03a8>] process_one_work+0x1d8/0x6e0
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The M4U IP blocks in mt2712 is MTK's generation2 M4U which use the
ARM Short-descriptor like mt8173, and most of the HW registers are
the same.
The difference is that there are 2 M4U HWs in mt2712 while there's
only one in mt8173. The purpose of 2 M4U HWs is for balance the
bandwidth.
Normally if there are 2 M4U HWs, there should be 2 iommu domains,
each M4U has a iommu domain.
Signed-off-by: Yong Wu <yong.wu@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Now that we have a custom printf format specifier, convert users of
full_name to use %pOF instead. This is preparation to remove storing
of the full path string for each node.
Signed-off-by: Rob Herring <robh@kernel.org>
Acked-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@free-electrons.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-arm-kernel@lists.infradead.org
Cc: linux-omap@vger.kernel.org
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
clk_prepare_enable() can fail here and we must check its return value.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
In the commit 3c8f4ad85c4b ("memory/mediatek: add support for mt2701"),
the larb->larbid was added but not initialized.
Mediatek's gen1 smi need this hardware larbid information to get the
register offset which controls whether enable iommu for this larb.
This patch add the initialize routine for larbid.
Reviewed-by: Matthias Brugger <matthias.bgg@gmail.com>
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
Replace custom code with generic helper to retrieve driver data.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The converter function for translating ns timings in register values was
initialized with a wrong function pointer. This resulted in wrong
register values also for the setup and pulse registers when configuring
the EBI interface trough dts.
Includes a small fix in a comment of the smc driver, which was probably
just a copy'n'paste mistake.
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Lee Jones <lee.jones@linaro.org>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
As reported in [1] and in [2] it's not possible to set the device tree
property 'atmel,smc-tdf-ns' to zero, although the SoC allows a setting
of 0ns for the t_DF time.
Allow this setting by doing the same thing as in the atmel nand
controller driver by setting ncycles to ATMEL_SMC_MODE_TDF_MIN if zero
is set in the dts.
[1] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-March/490966.html
[2] http://lists.infradead.org/pipermail/linux-arm-kernel/2017-July/520652.html
Suggested-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexander Dahl <ada@thorsis.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
