summaryrefslogtreecommitdiff
path: root/drivers/memory
AgeCommit message (Collapse)Author
2016-06-16memory: omap-gpmc: Fix omap gpmc EXTRADELAY timingOcquidant, Sebastien
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY is overwritten by the WEEXTRADELAY value from the device tree and GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device tree. As a consequence, the memory accesses cannot be configured properly when the extra delay are needed for OE and WE. Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the device tree file and prevents GPMC_CONFIG4_OEXTRADELAY being overwritten by the WEXTRADELAY value from the device tree. Cc: stable@vger.kernel.org Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-05-24Merge tag 'for-linus-20160523' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD updates from Brian Norris: "First cycle with Boris as NAND maintainer! Many (most) bullets stolen from him. Generic: - Migrated NAND LED trigger to be a generic MTD trigger NAND: - Introduction of the "ECC algorithm" concept, to avoid overloading the ECC mode field too much more - Replaced the nand_ecclayout infrastructure with something a little more flexible (finally!) and future proof - Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some of this into their own tree as well - Prepare the sunxi NAND driver to receive DMA support - Handle bitflips in erased pages on GPMI revisions that do not support this in hardware. SPI NOR: - Start using the spi_flash_read() API for SPI drivers that support it (i.e., SPI drivers with special memory-mapped flash modes) And other small scattered improvments" * tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits) mtd: spi-nor: support GigaDevice gd25lq64c mtd: nand_bch: fix spelling of "probably" mtd: brcmnand: respect ECC algorithm set by NAND subsystem gpmi-nand: Handle ECC Errors in erased pages Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value mtd: nand: add support for "nand-ecc-algo" DT property mtd: mtd: drop NAND_ECC_SOFT_BCH enum value mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping mtd: nand: read ECC algorithm from the new field mtd: nand: fsmc: validate ECC setup by checking algorithm directly mtd: nand: set ECC algorithm to Hamming on fallback staging: mt29f_spinand: set ECC algorithm explicitly CRIS v32: nand: set ECC algorithm explicitly mtd: nand: atmel: set ECC algorithm explicitly mtd: nand: davinci: set ECC algorithm explicitly mtd: nand: bf5xx: set ECC algorithm explicitly mtd: nand: omap2: Fix high memory dma prefetch transfer mtd: nand: omap2: Start dma request before enabling prefetch mtd: nandsim: add __init attribute mtd: nand: move of_get_nand_xxx() helpers into nand_base.c ...
2016-05-23Merge branch 'drm-next' of git://people.freedesktop.org/~airlied/linuxLinus Torvalds
Pull drm updates from Dave Airlie: "Here's the main drm pull request for 4.7, it's been a busy one, and I've been a bit more distracted in real life this merge window. Lots more ARM drivers, not sure if it'll ever end. I think I've at least one more coming the next merge window. But changes are all over the place, support for AMD Polaris GPUs is in here, some missing GM108 support for nouveau (found in some Lenovos), a bunch of MST and skylake fixes. I've also noticed a few fixes from Arnd in my inbox, that I'll try and get in asap, but I didn't think they should hold this up. New drivers: - Hisilicon kirin display driver - Mediatek MT8173 display driver - ARC PGU - bitstreamer on Synopsys ARC SDP boards - Allwinner A13 initial RGB output driver - Analogix driver for DisplayPort IP found in exynos and rockchip DRM Core: - UAPI headers fixes and C++ safety - DRM connector reference counting - DisplayID mode parsing for Dell 5K monitors - Removal of struct_mutex from drivers - Connector registration cleanups - MST robustness fixes - MAINTAINERS updates - Lockless GEM object freeing - Generic fbdev deferred IO support panel: - Support for a bunch of new panels i915: - VBT refactoring - PLL computation cleanups - DSI support for BXT - Color manager support - More atomic patches - GEM improvements - GuC fw loading fixes - DP detection fixes - SKL GPU hang fixes - Lots of BXT fixes radeon/amdgpu: - Initial Polaris support - GPUVM/Scheduler/Clock/Power improvements - ASYNC pageflip support - New mesa feature support nouveau: - GM108 support - Power sensor support improvements - GR init + ucode fixes. - Use GPU provided topology information vmwgfx: - Add host messaging support gma500: - Some cleanups and fixes atmel: - Bridge support - Async atomic commit support fsl-dcu: - Timing controller for LCD support - Pixel clock polarity support rcar-du: - Misc fixes exynos: - Pipeline clock support - Exynoss4533 SoC support - HW trigger mode support - export HDMI_PHY clock - DECON5433 fixes - Use generic prime functions - use DMA mapping APIs rockchip: - Lots of little fixes vc4: - Render node support - Gamma ramp support - DPI output support msm: - Mostly cleanups and fixes - Conversion to generic struct fence etnaviv: - Fix for prime buffer handling - Allow hangcheck to be coalesced with other wakeups tegra: - Gamme table size fix" * 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits) drm/edid: add displayid detailed 1 timings to the modelist. (v1.1) drm/edid: move displayid validation to it's own function. drm/displayid: Iterate over all DisplayID blocks drm/edid: move displayid tiled block parsing into separate function. drm: Nuke ->vblank_disable_allowed drm/vmwgfx: Report vmwgfx version to vmware.log drm/vmwgfx: Add VMWare host messaging capability drm/vmwgfx: Kill some lockdep warnings drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode drm/nouveau/core: recognise GM108 chipsets drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup drm/nouveau/gr/gk104-: share implementation of ppc exception init drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx drm/nouveau/bios/pll: check BIT table version before trying to parse it drm/nouveau/bios/pll: prevent oops when limits table can't be parsed drm/nouveau/volt/gk104: round up in gk104_volt_set drm/nouveau/fb/gm200: setup mmu debug buffer registers at init() drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init() drm/nouveau/fb/gf100-: allocate mmu debug buffers drm/nouveau/fb: allow chipset-specific actions for oneinit() ...
2016-05-20Merge tag 'char-misc-4.7-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char / misc driver updates from Greg KH: "Here's the big char and misc driver update for 4.7-rc1. Lots of different tiny driver subsystems have updates here with new drivers and functionality. Details in the shortlog. All have been in linux-next with no reported issues for a while" * tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (125 commits) mcb: Delete num_cells variable which is not required mcb: Fixed bar number assignment for the gdd mcb: Replace ioremap and request_region with the devm version mcb: Implement bus->dev.release callback mcb: export bus information via sysfs mcb: Correctly initialize the bus's device mei: bus: call mei_cl_read_start under device lock coresight: etb10: adjust read pointer only when needed coresight: configuring ETF in FIFO mode when acting as link coresight: tmc: implementing TMC-ETF AUX space API coresight: moving struct cs_buffers to header file coresight: tmc: keep track of memory width coresight: tmc: make sysFS and Perf mode mutually exclusive coresight: tmc: dump system memory content only when needed coresight: tmc: adding mode of operation for link/sinks coresight: tmc: getting rid of multiple read access coresight: tmc: allocating memory when needed coresight: tmc: making prepare/unprepare functions generic coresight: tmc: splitting driver in ETB/ETF and ETR components coresight: tmc: cleaning up header file ...
2016-05-06memory: mtk-smi: export mtk_smi_larb_get/putPhilipp Zabel
To allow building mediatek-drm.ko as a module, the mtk_smi_larb_get and mtk_smi_larb_put symbols have to be exported. Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
2016-05-01memory: of_memory: Silence uninitialized variable warningDan Carpenter
Presumably we never use the default: case statement which prints a warning message. But my static checker complains that if we do, we will hit an uninitialized variable warning. Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2016-04-19mtd: nand: omap2: rely on generic DT parsing done in nand_scan_ident()Boris Brezillon
The core now takes care of parsing generic DT properties in nand_scan_ident() when nand_set_flash_node() has been called. Rely on this initialization instead of calling of_get_nand_xxx() manually. Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com> Acked-by: Roger Quadros <rogerq@ti.com> Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
2016-04-19mtd/ifc: Add support for IFC controller version 2.0Raghav Dogra
The new IFC controller version 2.0 has a different memory map page. Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB. This patch segregates the IFC global and runtime registers to appropriate PAGE sizes. Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Signed-off-by: Raghav Dogra <raghav@freescale.com> Acked-by: Li Yang <leoyang.li@nxp.com> Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com> Acked-by: Scott Wood <oss@buserror.net> Acked-by: Brian Norris <computersforpeace@gmail.com> Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
2016-04-18memory: samsung: exynos-srom: Add support for bank configurationPavel Fedin
Implement handling properties in subnodes and adding child devices to the system. Child devices will not be added if configuration fails. Since the driver now does more than suspend-resume support, dependency on CONFIG_PM is removed. Signed-off-by: Pavel Fedin <p.fedin@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2016-04-18memory: Add support for Exynos SROM driverPankaj Dubey
This patch adds Exynos SROM controller driver which will handle save restore of SROM registers during S2R. Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com> Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com> [p.fedin@samsung.com: tested on SMDK5410] Tested-by: Pavel Fedin <p.fedin@samsung.com> Signed-off-by: Kukjin Kim <kgene@kernel.org> [k.kozlowski: Minor COMPILE_TEST adjustments in Kconfig entries] Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
2016-04-15memory: omap-gpmc: Prevent GPMC_STATUS from being accessed via gpmc_regsRoger Quadros
GPMC_STATUS register is private to the GPMC module and must not be accessed directly by NAND driver through the gpmc_regs. They must use gpmc_omap_get_nand_ops() instead. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Support WAIT pin edge interruptsRoger Quadros
OMAPs can have 2 to 4 WAITPINs that can be used as edge triggered interrupts if not used for memory wait state insertion. Support these interrupts via the gpmc IRQ domain. The gpmc IRQ domain interrupt map is: 0 - NAND_fifoevent 1 - NAND_termcount 2 - GPMC_WAIT0 edge 3 - GPMC_WAIT1 edge, and so on Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Reserve WAITPIN if needed for WAIT monitoringRoger Quadros
If the device attached to GPMC wants to use the WAIT pin for WAIT monitoring then we reserve it internally for exclusive use. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Support general purpose input for WAITPINsRoger Quadros
OMAPs can have 2 to 4 WAITPINs that can be used as general purpose input if not used for memory wait state insertion. The first user will be the OMAP NAND chip to get the NAND read/busy status using gpiolib. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Prevent mapping into 1st 16MBRoger Quadros
We have been preventing mapping GPMC children in the first 1MB but really it has to be the first 16MB as the minimum GPMC partition size is 16MB. Also print an error message if CS mapping fails due to DT requesting address outside the GPMC map. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15mtd: nand: omap: Clean up device tree supportRoger Quadros
Move NAND specific device tree parsing to NAND driver. The NAND controller node must have a compatible id, register space resource and interrupt resource. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Brian Norris <computersforpeace@gmail.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Implement IRQ domain for NAND IRQsRoger Quadros
GPMC provides 2 interrupts for NAND use. i.e. fifoevent and termcount. Use IRQ domain for this. NAND device tree node can then get the necessary interrupts by using gpmc as the interrupt parent. Legacy boot uses gpmc_get_client_irq to get the NAND interrupts from the GPMC IRQ domain. Get rid of custom bitmasks and use IRQ domain for that as well. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Rob Herring <robh@kernel.org> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Add GPMC-NAND ops to get writebufferempty statusRoger Quadros
This is needed by OMAP NAND driver to poll the empty status of the writebuffer. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-04-15memory: omap-gpmc: Introduce GPMC to NAND interfaceRoger Quadros
The OMAP GPMC module has certain registers dedicated for NAND access and some NAND bits mixed with other GPMC functionality. For the NAND dedicated registers we have the struct gpmc_nand_regs. The NAND driver needs to access NAND specific bits from the following non-dedicated registers - EMPTYWRITEBUFFERSTATUS from GPMC_STATUS For accessing these bits we introduce the struct gpmc_nand_ops. Add gpmc_omap_get_nand_ops() that returns the gpmc_nand_ops along with updating the gpmc_nand_regs. This API will be called by the OMAP NAND driver to access the necessary bits in GPMC register space. Signed-off-by: Roger Quadros <rogerq@ti.com> Acked-by: Tony Lindgren <tony@atomide.com>
2016-03-24Merge tag 'for-linus-20160324' of git://git.infradead.org/linux-mtdLinus Torvalds
Pull MTD updates from Brian Norris: "NAND: - Add sunxi_nand randomizer support - begin refactoring NAND ecclayout structs - fix pxa3xx_nand dmaengine usage - brcmnand: fix support for v7.1 controller - add Qualcomm NAND controller driver SPI NOR: - add new ls1021a, ls2080a support to Freescale QuadSPI - add new flash ID entries - support bottom-block protection for Winbond flash - support Status Register Write Protect - remove broken QPI support for Micron SPI flash JFFS2: - improve post-mount CRC scan efficiency General: - refactor bcm63xxpart parser, to later extend for NAND - add writebuf size parameter to mtdram Other minor code quality improvements" * tag 'for-linus-20160324' of git://git.infradead.org/linux-mtd: (72 commits) mtd: nand: remove kerneldoc for removed function parameter mtd: nand: Qualcomm NAND controller driver dt/bindings: qcom_nandc: Add DT bindings mtd: nand: don't select chip in nand_chip's block_bad op mtd: spi-nor: support lock/unlock for a few Winbond chips mtd: spi-nor: add TB (Top/Bottom) protect support mtd: spi-nor: add SPI_NOR_HAS_LOCK flag mtd: spi-nor: use BIT() for flash_info flags mtd: spi-nor: disallow further writes to SR if WP# is low mtd: spi-nor: make lock/unlock bounds checks more obvious and robust mtd: spi-nor: silently drop lock/unlock for already locked/unlocked region mtd: spi-nor: wait for SR_WIP to clear on initial unlock mtd: nand: simplify nand_bch_init() usage mtd: mtdswap: remove useless if (!mtd->ecclayout) test mtd: create an mtd_oobavail() helper and make use of it mtd: kill the ecclayout->oobavail field mtd: nand: check status before reporting timeout mtd: bcm63xxpart: give width specifier an 'int', not 'size_t' mtd: mtdram: Add parameter for setting writebuf size mtd: nand: pxa3xx_nand: kill unused field 'drcmr_cmd' ...
2016-03-22Merge tag 'iommu-updates-v4.6' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull IOMMU updates from Joerg Roedel: - updates for the Exynos IOMMU driver to make use of default domains and to add support for the SYSMMU v5 - new Mediatek IOMMU driver - support for the ARMv7 short descriptor format in the io-pgtable code - default domain support for the ARM SMMU - couple of other small fixes all over the place * tag 'iommu-updates-v4.6' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (41 commits) iommu/ipmmu-vmsa: Add r8a7795 DT binding iommu/mediatek: Check for NULL instead of IS_ERR() iommu/io-pgtable-armv7s: Fix kmem_cache_alloc() flags iommu/mediatek: Fix handling of of_count_phandle_with_args result iommu/dma: Fix NEED_SG_DMA_LENGTH dependency iommu/mediatek: Mark PM functions as __maybe_unused iommu/mediatek: Select ARM_DMA_USE_IOMMU iommu/exynos: Use proper readl/writel register interface iommu/exynos: Pointers are nto physical addresses dts: mt8173: Add iommu/smi nodes for mt8173 iommu/mediatek: Add mt8173 IOMMU driver memory: mediatek: Add SMI driver dt-bindings: mediatek: Add smi dts binding dt-bindings: iommu: Add binding for mediatek IOMMU iommu/ipmmu-vmsa: Use ARCH_RENESAS iommu/exynos: Support multiple attach_device calls iommu/exynos: Add Maintainers entry for Exynos SYSMMU driver iommu/exynos: Add support for v5 SYSMMU iommu/exynos: Update device tree documentation iommu/exynos: Add support for SYSMMU controller with bogus version reg ...
2016-02-25memory: mediatek: Add SMI driverYong Wu
This patch add SMI(Smart Multimedia Interface) driver. This driver is responsible to enable/disable iommu and control the power domain and clocks of each local arbiter. Signed-off-by: Yong Wu <yong.wu@mediatek.com> Tested-by: Philipp Zabel <p.zabel@pengutronix.de> Reviewed-by: Daniel Kurtz <djkurtz@chromium.org> Tested-by: Daniel Kurtz <djkurtz@chromium.org> Signed-off-by: Matthias Brugger <matthias.bgg@gmail.com> Signed-off-by: Joerg Roedel <jroedel@suse.de>
2016-02-08memory: omap-gpmc: Add support for AAD timingsNeil Armstrong
In order to support extended timings parameters on hardware supporting the "AAD" mode like the AM335x or DM816x, add these entries into the GPMC driver if the hardware is capable. Tested on DM816x and AM335x. Signed-off-by: Neil Armstrong <narmstrong@baylibre.com> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Roger Quadros <rogerq@ti.com>
2016-02-01driver/memory: Removal of deprecated NO_IRQRaghav Dogra
Replacing the NO_IRQ macro with 0. If there is no interrupt, returned value will be 0 regardless of what NO_IRQ is defined. Signed-off-by: Raghav Dogra <raghav@freescale.com> Signed-off-by: Brian Norris <computersforpeace@gmail.com>
2016-01-20Merge tag 'armsoc-drivers' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Driver updates for ARM SoCs. Some for SoC-family code under drivers/soc, but also some other driver updates that don't belong anywhere else. We also bring in the drivers/reset code through arm-soc. Some of the larger updates: - Qualcomm support for SMEM, SMSM, SMP2P. All used to communicate with other parts of the chip/board on these platforms, all proprietary protocols that don't fit into other subsystems and live in drivers/soc for now. - System bus driver for UniPhier - Driver for the TI Wakeup M3 IPC device - Power management for Raspberry PI + Again a bunch of other smaller updates and patches" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (38 commits) bus: uniphier: allow only built-in driver ARM: bcm2835: clarify RASPBERRYPI_FIRMWARE dependency MAINTAINERS: Drop Kumar Gala from QCOM bus: uniphier-system-bus: add UniPhier System Bus driver ARM: bcm2835: add rpi power domain driver dt-bindings: add rpi power domain driver bindings ARM: bcm2835: Define two new packets from the latest firmware. drivers/soc: make mediatek/mtk-scpsys.c explicitly non-modular soc: mediatek: SCPSYS: Add regulator support MAINTAINERS: Change QCOM entries soc: qcom: smd-rpm: Add existing platform support memory/tegra: Add number of TLB lines for Tegra124 reset: hi6220: fix modular build soc: qcom: Introduce WCNSS_CTRL SMD client ARM: qcom: select ARM_CPU_SUSPEND for power management MAINTAINERS: Add rules for Qualcomm dts files soc: qcom: enable smsm/smp2p modular build serial: msm_serial: Make config tristate soc: qcom: smp2p: Qualcomm Shared Memory Point to Point soc: qcom: smsm: Add driver for Qualcomm SMSM ...
2015-12-16fsl-ifc: add missing include on ARM64Lijun Pan
Need to include sched.h to fix the following compilation error if FSL_IFC is enabled on ARM64 machine. In file included from include/linux/mmzone.h:9:0, from include/linux/gfp.h:5, from include/linux/kmod.h:22, from include/linux/module.h:13, from drivers/memory/fsl_ifc.c:22: drivers/memory/fsl_ifc.c: In function ‘check_nand_stat’: include/linux/wait.h:165:35: error: ‘TASK_NORMAL’ undeclared (first use in this function) #define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL) ^ drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’ wake_up(&ctrl->nand_wait); ^ include/linux/wait.h:165:35: note: each undeclared identifier is reported only once for each function it appears in #define wake_up(x) __wake_up(x, TASK_NORMAL, 1, NULL) ^ drivers/memory/fsl_ifc.c:136:3: note: in expansion of macro ‘wake_up’ wake_up(&ctrl->nand_wait); ^ Analysis is as follows: I put some instrumental code and get the following .h files inclusion sequence: In file included from ./arch/arm64/include/asm/compat.h:25:0, from ./arch/arm64/include/asm/stat.h:23, from include/linux/stat.h:5, from include/linux/module.h:10, from drivers/memory/fsl_ifc.c:23: include/linux/sched.h:113:1: error: expected ‘=’, ‘,’, ‘;’, ‘asm’ or ‘__attribute__’ before ‘struct’ struct sched_attr { ^ CONFIG_COMPAT=y is enabled while 39 and 48 bit VA is selected. When 42 bit VA is selected, it does not enable CONFIG_COMPAT=y In ./arch/arm64/include/asm/stat.h:23, it has "#ifdef CONFIG_COMPAT" "#include <asm/compat.h>" "..." "#endif" Since ./arch/arm64/include/asm/stat.h does not include ./arch/arm64/include/asm/compat.h, then it will not include include/linux/sched.h Hence we have to manually add "#include <linux/sched.h>" in drivers/memory/fsl_ifc.c Signed-off-by: Lijun Pan <Lijun.Pan@freescale.com> Signed-off-by: Arnd Bergmann <arnd@arndb.de>
2015-12-14memory/tegra: Add number of TLB lines for Tegra124Vince Hsu
Tegra124 was accidentally left out when the number of TLB lines was parameterized in commit 11cec15bf3fb ("iommu/tegra-smmu: Parameterize number of TLB lines"). Fortunately this doesn't cause any noticeable regressions upstream, presumably because there aren't any use-cases that exercise enough pressure on the SMMU. But it is a regression nonetheless, so let's fix it. Fixes: 11cec15bf3fb ("iommu/tegra-smmu: Parameterize number of TLB lines") Signed-off-by: Vince Hsu <vince.h@nvidia.com> Signed-off-by: Tomasz Figa <tfiga@chromium.org> [treding@nvidia.com: extract from unrelated patch] Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-11-10Merge tag 'armsoc-drivers' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "As we've enabled multiplatform kernels on ARM, and greatly done away with the contents under arch/arm/mach-*, there's still need for SoC-related drivers to go somewhere. Many of them go in through other driver trees, but we still have drivers/soc to hold some of the "doesn't fit anywhere" lowlevel code that might be shared between ARM and ARM64 (or just in general makes sense to not have under the architecture directory). This branch contains mostly such code: - Drivers for qualcomm SoCs for SMEM, SMD and SMD-RPM, used to communicate with power management blocks on these SoCs for use by clock, regulator and bus frequency drivers. - Allwinner Reduced Serial Bus driver, again used to communicate with PMICs. - Drivers for ARM's SCPI (System Control Processor). Not to be confused with PSCI (Power State Coordination Interface). SCPI is used to communicate with the assistant embedded cores doing power management, and we have yet to see how many of them will implement this for their hardware vs abstracting in other ways (or not at all like in the past). - To make confusion between SCPI and PSCI more likely, this release also includes an update of PSCI to interface version 1.0. - Rockchip support for power domains. - A driver to talk to the firmware on Raspberry Pi" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (57 commits) soc: qcom: smd-rpm: Correct size of outgoing message bus: sunxi-rsb: Add driver for Allwinner Reduced Serial Bus bus: sunxi-rsb: Add Allwinner Reduced Serial Bus (RSB) controller bindings ARM: bcm2835: add mutual inclusion protection drivers: psci: make PSCI 1.0 functions initialization version dependent dt-bindings: Correct paths in Rockchip power domains binding document soc: rockchip: power-domain: don't try to print the clock name in error case soc: qcom/smem: add HWSPINLOCK dependency clk: berlin: add cpuclk ARM: berlin: dts: add CLKID_CPU for BG2Q ARM: bcm2835: Add the Raspberry Pi firmware driver soc: qcom: smem: Move RPM message ram out of smem DT node soc: qcom: smd-rpm: Correct the active vs sleep state flagging soc: qcom: smd: delete unneeded of_node_put firmware: qcom-scm: build for correct architecture level soc: qcom: smd: Correct SMEM items for upper channels qcom-scm: add missing prototype for qcom_scm_is_available() qcom-scm: fix endianess issue in __qcom_scm_is_call_available soc: qcom: smd: Reject send of too big packets soc: qcom: smd: Handle big endian CPUs ...
2015-11-04Merge tag 'char-misc-4.4-rc1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc Pull char/misc driver updates from Greg KH: "Here is the big char/misc driver update for 4.4-rc1. Lots of different driver and subsystem updates, hwtracing being the largest with the addition of some new platforms that are now supported. Full details in the shortlog. All of these have been in linux-next for a long time with no reported issues" * tag 'char-misc-4.4-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (181 commits) fpga: socfpga: Fix check of return value of devm_request_irq lkdtm: fix ACCESS_USERSPACE test mcb: Destroy IDA on module unload mcb: Do not return zero on error path in mcb_pci_probe() mei: bus: set the device name before running fixup mei: bus: use correct lock ordering mei: Fix debugfs filename in error output char: ipmi: ipmi_ssif: Replace timeval with timespec64 fpga: zynq-fpga: Fix issue with drvdata being overwritten. fpga manager: remove unnecessary null pointer checks fpga manager: ensure lifetime with of_fpga_mgr_get fpga: zynq-fpga: Change fw format to handle bin instead of bit. fpga: zynq-fpga: Fix unbalanced clock handling misc: sram: partition base address belongs to __iomem space coresight: etm3x: adding documentation for sysFS's cpu interface vme: 8-bit status/id takes 256 values, not 255 fpga manager: Adding FPGA Manager support for Xilinx Zynq 7000 ARM: zynq: dt: Updated devicetree for Zynq 7000 platform. ARM: dt: fpga: Added binding docs for Xilinx Zynq FPGA manager. ver_linux: proc/modules, limit text processing to 'sed' ...
2015-10-12memory: omap-gpmc: dump "before" state before first modificationUwe Kleine-König
When gpmc_cs_show_timings is called in gpmc_cs_set_timings() gpmc_cs_program_settings() was already run which modifies the CONFIG1 register. So to be more useful do the "before" dump earlier. Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-12memory: omap-gpmc: Fix unselectable debug option for GPMCTony Lindgren
Commit 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") added a debug option for GPMC, but somehow managed to keep it unselectable. This probably happened because I had some uncommitted changes and the GPMC option is selected in the platform specific Kconfig. Let's also update the description a bit, it does not mention that enabling the debug option also disables the reset of GPMC controller during the init as pointed out by Uwe Kleine-König <u.kleine-koenig@pengutronix.de> and Roger Quadros <rogerq@ti.com>. Fixes: 63aa945b1013 ("memory: omap-gpmc: Add Kconfig option for debug") Reported-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de> Acked-by: Roger Quadros <rogerq@ti.com> Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-10-05memory: ti-aemif: Fix module autoload for OF platform driverLuis de Bethencourt
This platform driver has a OF device ID table but the OF module alias information is not created so module autoloading won't work. Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-10-05memory: fsl-corenet: Fix module autoload for OF platform driverLuis de Bethencourt
This platform driver has a OF device ID table but the OF module alias information is not created so module autoloading won't work. Signed-off-by: Luis de Bethencourt <luisbg@osg.samsung.com> Acked-by: Scott Wood <scottwood@freescale.com> Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
2015-09-29memory: pl172: add ARM PrimeCell PL176 MPMC supportVladimir Zapolskiy
The change adds support of ARM PrimeCell PL176 MPMC. Static memory configuration of PL175 MPMC is very similar to one found on PL172 and PL175 controllers, so it is preferred to add its support into the existing driver. The difference is that PL176 supports up to 10 slave ports (but only 4 of them may be connected to static memory devices), AHB master bus width cab be 64-bit wide, also NAND devices can be interfaced. Similar to PL175 contoller, PL176 has no write buffer enable control in static memory configuration register, the rest of static memory configuration bits (with exception of NAND) is the same. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Joachim Eastwood <manabian@gmail.com>
2015-09-29memory: pl172: add ARM PrimeCell PL175 MPMC supportVladimir Zapolskiy
The change adds support of ARM PrimeCell PL175 MPMC, the controller is found on NXP LPC32xx SoC. PL175 MPMC is very similar to PL172 controller, so it is preferred to add its support into the existing driver. One of the differences between PL172 and PL175 is that the latter one supports up to 6 AHB ports, but still only 4 AHB ports can be assigned to a static memory device, also PL175 does not have write buffer enable control in static memory configuration register. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Joachim Eastwood <manabian@gmail.com>
2015-09-29memory: pl172: correct MPMC peripheral ID register bitsVladimir Zapolskiy
According to PL172 TRM read of bits [7:6] of MPMCPeriphID3 is undefined, so unmask them. Also the driver supports all currently present revisions of PL172, this allows to alleviate requirements to the revision version matched by the driver. Signed-off-by: Vladimir Zapolskiy <vz@mleia.com> Signed-off-by: Joachim Eastwood <manabian@gmail.com>
2015-09-08Merge tag 'iommu-updates-v4.3' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu Pull iommu updates for from Joerg Roedel: "This time the IOMMU updates are mostly cleanups or fixes. No big new features or drivers this time. In particular the changes include: - Bigger cleanup of the Domain<->IOMMU data structures and the code that manages them in the Intel VT-d driver. This makes the code easier to understand and maintain, and also easier to keep the data structures in sync. It is also a preparation step to make use of default domains from the IOMMU core in the Intel VT-d driver. - Fixes for a couple of DMA-API misuses in ARM IOMMU drivers, namely in the ARM and Tegra SMMU drivers. - Fix for a potential buffer overflow in the OMAP iommu driver's debug code - A couple of smaller fixes and cleanups in various drivers - One small new feature: Report domain-id usage in the Intel VT-d driver to easier detect bugs where these are leaked" * tag 'iommu-updates-v4.3' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (83 commits) iommu/vt-d: Really use upper context table when necessary x86/vt-d: Fix documentation of DRHD iommu/fsl: Really fix init section(s) content iommu/io-pgtable-arm: Unmap and free table when overwriting with block iommu/io-pgtable-arm: Move init-fn declarations to io-pgtable.h iommu/msm: Use BUG_ON instead of if () BUG() iommu/vt-d: Access iomem correctly iommu/vt-d: Make two functions static iommu/vt-d: Use BUG_ON instead of if () BUG() iommu/vt-d: Return false instead of 0 in irq_remapping_cap() iommu/amd: Use BUG_ON instead of if () BUG() iommu/amd: Make a symbol static iommu/amd: Simplify allocation in irq_remapping_alloc() iommu/tegra-smmu: Parameterize number of TLB lines iommu/tegra-smmu: Factor out tegra_smmu_set_pde() iommu/tegra-smmu: Extract tegra_smmu_pte_get_use() iommu/tegra-smmu: Use __GFP_ZERO to allocate zeroed pages iommu/tegra-smmu: Remove PageReserved manipulation iommu/tegra-smmu: Convert to use DMA API iommu/tegra-smmu: smmu_flush_ptc() wants device addresses ...
2015-09-03Merge tag 'powerpc-4.3-1' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux Pull powerpc updates from Michael Ellerman: - support "hybrid" iommu/direct DMA ops for coherent_mask < dma_mask from Benjamin Herrenschmidt - EEH fixes for SRIOV from Gavin - introduce rtas_get_sensor_fast() for IRQ handlers from Thomas Huth - use hardware RNG for arch_get_random_seed_* not arch_get_random_* from Paul Mackerras - seccomp filter support from Michael Ellerman - opal_cec_reboot2() handling for HMIs & machine checks from Mahesh Salgaonkar - add powerpc timebase as a trace clock source from Naveen N. Rao - misc cleanups in the xmon, signal & SLB code from Anshuman Khandual - add an inline function to update POWER8 HID0 from Gautham R. Shenoy - fix pte_pagesize_index() crash on 4K w/64K hash from Michael Ellerman - drop support for 64K local store on 4K kernels from Michael Ellerman - move dma_get_required_mask() from pnv_phb to pci_controller_ops from Andrew Donnellan - initialize distance lookup table from drconf path from Nikunj A Dadhania - enable RTC class support from Vaibhav Jain - disable automatically blocked PCI config from Gavin Shan - add LEDs driver for PowerNV platform from Vasant Hegde - fix endianness issues in the HVSI driver from Laurent Dufour - kexec endian fixes from Samuel Mendoza-Jonas - fix corrupted pdn list from Gavin Shan - fix fenced PHB caused by eeh_slot_error_detail() from Gavin Shan - Freescale updates from Scott: Highlights include 32-bit memcpy/memset optimizations, checksum optimizations, 85xx config fragments and updates, device tree updates, e6500 fixes for non-SMP, and misc cleanup and minor fixes. - a ton of cxl updates & fixes: - add explicit precision specifiers from Rasmus Villemoes - use more common format specifier from Rasmus Villemoes - destroy cxl_adapter_idr on module_exit from Johannes Thumshirn - destroy afu->contexts_idr on release of an afu from Johannes Thumshirn - compile with -Werror from Daniel Axtens - EEH support from Daniel Axtens - plug irq_bitmap getting leaked in cxl_context from Vaibhav Jain - add alternate MMIO error handling from Ian Munsie - allow release of contexts which have been OPENED but not STARTED from Andrew Donnellan - remove use of macro DEFINE_PCI_DEVICE_TABLE from Vaishali Thakkar - release irqs if memory allocation fails from Vaibhav Jain - remove racy attempt to force EEH invocation in reset from Daniel Axtens - fix + cleanup error paths in cxl_dev_context_init from Ian Munsie - fix force unmapping mmaps of contexts allocated through the kernel api from Ian Munsie - set up and enable PSL Timebase from Philippe Bergheaud * tag 'powerpc-4.3-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (140 commits) cxl: Set up and enable PSL Timebase cxl: Fix force unmapping mmaps of contexts allocated through the kernel api cxl: Fix + cleanup error paths in cxl_dev_context_init powerpc/eeh: Fix fenced PHB caused by eeh_slot_error_detail() powerpc/pseries: Cleanup on pci_dn_reconfig_notifier() powerpc/pseries: Fix corrupted pdn list powerpc/powernv: Enable LEDS support powerpc/iommu: Set default DMA offset in dma_dev_setup cxl: Remove racy attempt to force EEH invocation in reset cxl: Release irqs if memory allocation fails cxl: Remove use of macro DEFINE_PCI_DEVICE_TABLE powerpc/powernv: Fix mis-merge of OPAL support for LEDS driver powerpc/powernv: Reset HILE before kexec_sequence() powerpc/kexec: Reset secondary cpu endianness before kexec powerpc/hvsi: Fix endianness issues in the HVSI driver leds/powernv: Add driver for PowerNV platform powerpc/powernv: Create LED platform device powerpc/powernv: Add OPAL interfaces for accessing and modifying system LED states powerpc/powernv: Fix the log message when disabling VF cxl: Allow release of contexts which have been OPENED but not STARTED ...
2015-09-01Merge tag 'armsoc-drivers' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC driver updates from Olof Johansson: "Some releases this branch is nearly empty, others we have more stuff. It tends to gather drivers that need SoC modification or dependencies such that they have to (also) go in through our tree. For this release, we have merged in part of the reset controller tree (with handshake that the parts we have merged in will remain stable), as well as dependencies on a few clock branches. In general, new items here are: - Qualcomm driver for SMM/SMD, which is how they communicate with the coprocessors on (some) of their platforms - memory controller work for ARM's PL172 memory controller - reset drivers for various platforms - PMU power domain support for Marvell platforms - Tegra support for T132/T210 SoCs: PMC, fuse, memory controller per-SoC support" * tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (49 commits) ARM: tegra: cpuidle: implement cpuidle_state.enter_freeze() ARM: tegra: Disable cpuidle if PSCI is available soc/tegra: pmc: Use existing pclk reference soc/tegra: pmc: Remove unnecessary return statement soc: tegra: Remove redundant $(CONFIG_ARCH_TEGRA) in Makefile memory: tegra: Add Tegra210 support memory: tegra: Add support for a variable-size client ID bitfield clk: shmobile: rz: Add CPG/MSTP Clock Domain support clk: shmobile: rcar-gen2: Add CPG/MSTP Clock Domain support clk: shmobile: r8a7779: Add CPG/MSTP Clock Domain support clk: shmobile: r8a7778: Add CPG/MSTP Clock Domain support clk: shmobile: Add CPG/MSTP Clock Domain support ARM: dove: create a proper PMU driver for power domains, PMU IRQs and resets reset: reset-zynq: Adding support for Xilinx Zynq reset controller. docs: dts: Added documentation for Xilinx Zynq Reset Controller bindings. MIPS: ath79: Add the reset controller to the AR9132 dtsi reset: Add a driver for the reset controller on the AR71XX/AR9XXX devicetree: Add bindings for the ATH79 reset controller reset: socfpga: Update reset-socfpga to read the altr,modrst-offset property doc: dt: add documentation for lpc1850-rgu reset driver ...
2015-09-01Merge tag 'armsoc-soc' of ↵Linus Torvalds
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc Pull ARM SoC platform updates from Olof Johansson: "New or improved SoC support: - add support for Atmel's SAMA5D2 SoC - add support for Freescale i.MX6UL - improved support for TI's DM814x platform - misc fixes and improvements for RockChip platforms - Marvell MVEBU suspend/resume support A few driver changes that ideally would belong in the drivers branch are also here (acked by appropriate maintainers): - power key input driver for Freescale platforms (svns) - RTC driver updates for Freescale platforms (svns/mxc) - clk fixes for TI DM814/816X + a bunch of other changes for various platforms" * tag 'armsoc-soc' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (83 commits) ARM: rockchip: pm: Fix PTR_ERR() argument ARM: imx: mach-imx6ul: Fix allmodconfig build clk: ti: fix for definition movement ARM: uniphier: drop v7_invalidate_l1 call at secondary entry memory: kill off set_irq_flags usage rtc: snvs: select option REGMAP_MMIO ARM: brcmstb: select ARCH_DMA_ADDR_T_64BIT for LPAE ARM: BCM: Enable ARM erratum 798181 for BRCMSTB ARM: OMAP2+: Fix power domain operations regression caused by 81xx ARM: rockchip: enable PMU_GPIOINT_WAKEUP_EN when entering shallow suspend ARM: rockchip: set correct stabilization thresholds in suspend ARM: rockchip: rename osc_switch_to_32k variable ARM: imx6ul: add fec MAC refrence clock and phy fixup init ARM: imx6ul: add fec bits to GPR syscon definition rtc: mxc: add support of device tree dt-binding: document the binding for mxc rtc rtc: mxc: use a second rtc clock ARM: davinci: cp_intc: use IRQCHIP_SKIP_SET_WAKE instead of irq_set_wake callback soc: mediatek: Fix SCPSYS compilation ARM: at91/soc: add basic support for new sama5d2 SoC ...
2015-08-20Merge tag 'tegra-for-4.3-memory' of ↵Olof Johansson
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers ARM: tegra: Memory controller updates for v4.3-rc1 Adds support for Tegra210, which allows the SMMU to be used on this new SoC generation. * tag 'tegra-for-4.3-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux: memory: tegra: Add Tegra210 support memory: tegra: Add support for a variable-size client ID bitfield memory: tegra: Expose supported rates via debugfs Signed-off-by: Olof Johansson <olof@lixom.net>
2015-08-17Merge tag 'tegra-for-4.3-iommu' of ↵Joerg Roedel
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into arm/tegra iommu/tegra-smmu: Changes for v4.3-rc1 A bunch of improvements by Russell King, along with a fix to restore display support when using the SMMU. This was due to the SMMU driver writing the wrong value of active TLB lines, effectively disabling the TLB and causing massive underflows on the display controller because of the latency introduced by the SMMU.
2015-08-13iommu/tegra-smmu: Parameterize number of TLB linesThierry Reding
The number of TLB lines was increased from 16 on Tegra30 to 32 on Tegra114 and later. Parameterize the value so that the initial default can be set accordingly. On Tegra30, initializing the value to 32 would effectively disable the TLB and hence cause massive latencies for memory accesses translated through the SMMU. This is especially noticeable for isochronuous clients such as display, whose FIFOs would continuously underrun. Fixes: 891846516317 ("memory: Add NVIDIA Tegra memory controller support") Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-13memory: tegra: Add Tegra210 supportThierry Reding
Add the table of memory clients and SWGROUPs for Tegra210 to enable SMMU support for this new SoC. Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-13memory: tegra: Add support for a variable-size client ID bitfieldPaul Walmsley
Recent versions of the Tegra MC hardware extend the size of the client ID bitfield in the MC_ERR_STATUS register by one bit. While one could simply extend the bitfield for older hardware, that would allow data from reserved bits into the driver code, which is generally a bad idea on principle. So this patch instead passes in the client ID mask from from the per-SoC MC data. There's no MC support for T210 (yet), but when that support winds up in the kernel, the appropriate soc->client_id_mask value for that chip will be 0xff. Based on an original patch by David Ung <davidu@nvidia.com>. Signed-off-by: Paul Walmsley <paul@pwsan.com> Cc: Paul Walmsley <pwalmsley@nvidia.com> Cc: Thierry Reding <treding@nvidia.com> Cc: David Ung <davidu@nvidia.com> Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-13iommu/tegra-smmu: Move flush_dcache to tegra-smmu.cRussell King
Drivers should not be using __cpuc_* functions nor outer_cache_flush() directly. This change partly cleans up tegra-smmu.c. The only difference between cache handling of the tegra variants is Denver, which omits the call to outer_cache_flush(). This is due to Denver being an ARM64 CPU, and the ARM64 architecture does not provide this function. (This, in itself, is a good reason why these should not be used.) Signed-off-by: Russell King <rmk+kernel@arm.linux.org.uk> [treding@nvidia.com: fix build failure on 64-bit ARM] Signed-off-by: Thierry Reding <treding@nvidia.com>
2015-08-13memory: kill off set_irq_flags usageRob Herring
set_irq_flags is ARM specific with custom flags which have genirq equivalents. Convert drivers to use the genirq interfaces directly, so we can kill off set_irq_flags. The translation of flags is as follows: IRQF_VALID -> !IRQ_NOREQUEST IRQF_PROBE -> !IRQ_NOPROBE IRQF_NOAUTOEN -> IRQ_NOAUTOEN For IRQs managed by an irqdomain, the irqdomain core code handles clearing and setting IRQ_NOREQUEST already, so there is no need to do this in .map() functions and we can simply remove the set_irq_flags calls. Some users also set IRQ_NOPROBE and this has been maintained although it is not clear that is really needed. There appears to be a great deal of blind copy and paste of this code. Signed-off-by: Rob Herring <robh@kernel.org> Acked-by: Roger Quadros <rogerq@ti.com> Cc: linux-omap@vger.kernel.org Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-08-12memory: omap-gpmc: Don't try to save uninitialized GPMC contextTomeu Vizoso
If for some reason the GPMC device hasn't been probed yet, gpmc_base is going to be NULL. Because there's no context yet to be saved, just turn these functions into no-ops until that device gets probed. Unable to handle kernel NULL pointer dereference at virtual address 00000010 pgd = c0204000 [00000010] *pgd=00000000 Internal error: Oops: 5 [#1] SMP ARM Modules linked in: CPU: 0 PID: 0 Comm: swapper/0 Not tainted 4.2.0-rc5-next-20150804-05947-g23f38fe8eda9 #1 Hardware name: Generic OMAP3-GP (Flattened Device Tree) task: c0e623e8 ti: c0e5c000 task.ti: c0e5c000 PC is at omap3_gpmc_save_context+0x8/0xc4 LR is at omap_sram_idle+0x154/0x23c pc : [<c087c7ac>] lr : [<c023262c>] psr: 60000193 sp : c0e5df40 ip : c0f92a80 fp : c0999eb0 r10: c0e57364 r9 : c0e66f14 r8 : 00000003 r7 : 00000000 r6 : 00000003 r5 : 00000000 r4 : c0f5f174 r3 : c0fa4fe8 r2 : 00000000 r1 : 00000000 r0 : fa200280 Flags: nZCv IRQs off FIQs on Mode SVC_32 ISA ARM Segment kernel Control: 10c5387d Table: 80204019 DAC: 00000015 Process swapper/0 (pid: 0, stack limit = 0xc0e5c220) Stack: (0xc0e5df40 to 0xc0e5e000) df40: 00000000 c0e66ef8 c0f5f1a4 00000000 00000003 c02333a4 c3813822 00000000 df60: 00000000 c0e5a5c8 cfb8a5d0 c07f0c44 0e4f1d7e 00000000 00000000 00000000 df80: c3813822 00000000 cfb8a5d0 c0e5e4e4 cfb8a5d0 c0e66f14 c0e5a5c8 c0e5e54c dfa0: c0e5e544 c0e57364 c0999eb0 c0277758 000000fa c0f5d000 00000000 c0d61c18 dfc0: ffffffff ffffffff 00000000 c0d61674 00000000 c0df7a48 00000000 c0f5d5d4 dfe0: c0e5e4c0 c0df7a44 c0e634f8 80204059 00000000 8020807c 00000000 00000000 [<c087c7ac>] (omap3_gpmc_save_context) from [<c023262c>] (omap_sram_idle+0x154/0x23c) [<c023262c>] (omap_sram_idle) from [<c02333a4>] (omap3_enter_idle_bm+0xec/0x1a8) [<c02333a4>] (omap3_enter_idle_bm) from [<c07f0c44>] (cpuidle_enter_state+0xbc/0x284) [<c07f0c44>] (cpuidle_enter_state) from [<c0277758>] (cpu_startup_entry+0x174/0x24c) [<c0277758>] (cpu_startup_entry) from [<c0d61c18>] (start_kernel+0x358/0x3c0) [<c0d61c18>] (start_kernel) from [<8020807c>] (0x8020807c) Code: c0ccace8 c0ccacc0 e59f30b4 e5932000 (e5921010) Signed-off-by: Tomeu Vizoso <tomeu.vizoso@collabora.com> Suggested-by: Javier Martinez Canillas <javier@dowhile0.org> Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com> Acked-by: Roger Quadros <rogerq@ti.com> [tony@atomide.com: updated description as suggested by Javier] Signed-off-by: Tony Lindgren <tony@atomide.com>
2015-08-07fsl_ifc: Change IO accessor based on endiannessJaiprakash Singh
IFC IO accressor are set at run time based on IFC IP registers endianness.IFC node in DTS file contains information about endianness. Signed-off-by: Jaiprakash Singh <b44839@freescale.com> Signed-off-by: Scott Wood <scottwood@freescale.com> Acked-by: Brian Norris <computersforpeace@gmail.com>
2015-07-22memory: pl172: fix modular buildJoachim Eastwood
Building pl172 as a module fails with: > ERROR: "of_default_bus_match_table" [drivers/memory/pl172.ko] undefined! Because the symbol of_default_bus_match_table isn't exported by the OF core code so can't be referenced from modules. Fix this by removing the usage of of_default_bus_match_table for now. The side effect of this is that child nodes can't use "simple-bus" or "simple-mfd". Reported-by: Mark Brown <broonie@kernel.org> Signed-off-by: Joachim Eastwood <manabian@gmail.com> Signed-off-by: Olof Johansson <olof@lixom.net>