| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Arnd Bergmann:
"Driver updates for ARM SoCs, including a couple of newly added
drivers:
- The Qualcomm external bus interface 2 (EBI2), used in some of their
mobile phone chips for connecting flash memory, LCD displays or
other peripherals
- Secure monitor firmware for Amlogic SoCs, and an NVMEM driver for
the EFUSE based on that firmware interface.
- Perf support for the AppliedMicro X-Gene performance monitor unit
- Reset driver for STMicroelectronics STM32
- Reset driver for SocioNext UniPhier SoCs
Aside from these, there are minor updates to SoC-specific bus,
clocksource, firmware, pinctrl, reset, rtc and pmic drivers"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (50 commits)
bus: qcom-ebi2: depend on HAS_IOMEM
pinctrl: mvebu: orion5x: Generalise mv88f5181l support for 88f5181
clk: mvebu: Add clk support for the orion5x SoC mv88f5181
dt-bindings: EXYNOS: Add Exynos5433 PMU compatible
clocksource: exynos_mct: Add the support for ARM64
perf: xgene: Add APM X-Gene SoC Performance Monitoring Unit driver
Documentation: Add documentation for APM X-Gene SoC PMU DTS binding
MAINTAINERS: Add entry for APM X-Gene SoC PMU driver
bus: qcom: add EBI2 driver
bus: qcom: add EBI2 device tree bindings
rtc: rtc-pm8xxx: Add support for pm8018 rtc
nvmem: amlogic: Add Amlogic Meson EFUSE driver
firmware: Amlogic: Add secure monitor driver
soc: qcom: smd: Reset rx tail rather than tx
memory: atmel-sdramc: fix a possible NULL dereference
reset: hi6220: allow to compile test driver on other architectures
reset: zynq: add driver Kconfig option
reset: sunxi: add driver Kconfig option
reset: stm32: add driver Kconfig option
reset: socfpga: add driver Kconfig option
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char/misc driver updates from Greg KH:
"Here's the "big" char and misc driver update for 4.9-rc1.
Lots of little things here, all over the driver tree for subsystems
that flow through me. Nothing major that I can discern, full details
are in the shortlog.
All have been in the linux-next tree with no reported issues"
* tag 'char-misc-4.9-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (144 commits)
drivers/misc/hpilo: Changes to support new security states in iLO5 FW
at25: fix debug and error messaging
misc/genwqe: ensure zero initialization
vme: fake: remove unexpected unlock in fake_master_set()
vme: fake: mark symbols static where possible
spmi: pmic-arb: Return an error code if sanity check fails
Drivers: hv: get rid of id in struct vmbus_channel
Drivers: hv: make VMBus bus ids persistent
mcb: Add a dma_device to mcb_device
mcb: Enable PCI bus mastering by default
mei: stop the stall timer worker if not needed
clk: probe common clock drivers earlier
vme: fake: fix build for 64-bit dma_addr_t
ttyprintk: Neaten and simplify printing
mei: me: add kaby point device ids
coresight: tmc: mark symbols static where possible
coresight: perf: deal with error condition properly
Drivers: hv: hv_util: Avoid dynamic allocation in time synch
fpga manager: Add hardware dependency to Zynq driver
Drivers: hv: utils: Support TimeSync version 4.0 protocol samples.
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux into next/drivers
Pull "at91 drivers for 4.9" from Alexandre Belloni:
- Coccinelle fixes for atmel-ebi and atmel-sdramc
* tag 'at91-ab-4.9-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/abelloni/linux:
memory: atmel-sdramc: fix a possible NULL dereference
memory: atmel-ebi: use PTR_ERR_OR_ZERO() to simplify the code
|
|
next/drivers
This is also going to be part of v4.8 and sent as a bugfix,
merging it here to avoid a small conflict against the other
gpmc changes.
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
|
|
of_match_device could return NULL, and so cause a NULL pointer
dereference later.
For fixing this problem, we use of_device_get_match_data(), this will
simplify the code a little by using a standard function for
getting the match data.
Signed-off-by: LABBE Corentin <clabbe.montjoie@gmail.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
We get 2 warnings when biuld kernel with W=1:
drivers/memory/of_memory.c:30:30: warning: no previous prototype for 'of_get_min_tck' [-Wmissing-prototypes]
drivers/memory/of_memory.c:106:30: warning: no previous prototype for 'of_get_ddr_timings' [-Wmissing-prototypes]
In fact, these functions are declared in drivers/memory/of_memory.h
so this patch add missing header dependencies.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
We get 1 warning when build kernel with W=1:
drivers/memory/omap-gpmc.c:354:14: warning: no previous prototype for 'gpmc_clk_ticks_to_ns' [-Wmissing-prototypes]
In fact, this function is only used in the file in which it is declared
and don't need a declaration, but can be made static.
so this patch marks it 'static'.
Signed-off-by: Baoyou Xie <baoyou.xie@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
This saves a few codelines in the driver.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
"gpiochip_free_own_desc"
The gpiochip_free_own_desc() function tests whether its argument is NULL
and then returns immediately. Thus the test around the call is not needed.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Use PTR_ERR_OR_ZERO rather than if(IS_ERR(...)) + PTR_ERR.
Generated by coccinelle.
Signed-off-by: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
A recent commit (inadvertently?) changed how failed probe of a gpmc
child node was handled. Instead of proceeding with setting up any other
children as before, a single error now aborts the whole process.
This change broke networking on some Overo boards due to probe failing
for an unrelated nand node. This second issue should obviously be
fixed, but let's restore the old behaviour of allowing child-node
probe to fail to avoid further similar breakage on other systems.
Fixes: d2d00862dfbb ("memory: omap-gpmc: Support general purpose input
for WAITPINs")
Cc: stable@vger.kernel.org # v4.7+
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
Pull MTD updates from Brian Norris:
"NAND:
Quoting Boris:
'This pull request contains only one notable change:
- Addition of the MTK NAND controller driver
And a bunch of specific NAND driver improvements/fixes. Here are the
changes that are worth mentioning:
- A few fixes/improvements for the xway NAND controller driver
- A few fixes for the sunxi NAND controller driver
- Support for DMA in the sunxi NAND driver
- Support for the sunxi NAND controller IP embedded in A23/A33 SoCs
- Addition for bitflips detection in erased pages to the brcmnand driver
- Support for new brcmnand IPs
- Update of the OMAP-GPMC binding to support DMA channel description'
In addition, some small fixes around error handling, etc., as well
as one long-standing corner case issue (2.6.20, I think?) with
writing 1 byte less than a page.
NOR:
- rework some error handling on reads and writes, so we can better
handle (for instance) SPI controllers which have limitations on
their maximum transfer size
- add new Cadence Quad SPI flash controller driver
- add new Atmel QSPI flash controller driver
- add new Hisilicon SPI flash controller driver
- support a few new flash, and update supported features on others
- fix the logic used for detecting a fully-unlocked flash
And other miscellaneous small fixes"
* tag 'for-linus-20160801' of git://git.infradead.org/linux-mtd: (60 commits)
mtd: spi-nor: don't build Cadence QuadSPI on non-ARM
mtd: mtk-nor: remove duplicated include from mtk-quadspi.c
mtd: nand: fix bug writing 1 byte less than page size
mtd: update description of MTD_BCM47XXSFLASH symbol
mtd: spi-nor: Add driver for Cadence Quad SPI Flash Controller
mtd: spi-nor: Bindings for Cadence Quad SPI Flash Controller driver
mtd: nand: brcmnand: Change BUG_ON in brcmnand_send_cmd
mtd: pmcmsp-flash: Allocating too much in init_msp_flash()
mtd: maps: sa1100-flash: potential NULL dereference
mtd: atmel-quadspi: add driver for Atmel QSPI controller
mtd: nand: omap2: fix return value check in omap_nand_probe()
Documentation: atmel-quadspi: add binding file for Atmel QSPI driver
mtd: spi-nor: add hisilicon spi-nor flash controller driver
mtd: spi-nor: support dual, quad, and WP for Gigadevice
mtd: spi-nor: Added support for n25q00a.
memory: Update dependency of IFC for Layerscape
mtd: nand: jz4780: Update MODULE_AUTHOR email address
mtd: nand: sunxi: prevent a small memory leak
mtd: nand: sunxi: add reset line support
mtd: nand: sunxi: update DT bindings
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc
Pull ARM SoC driver updates from Olof Johansson:
"Driver updates for ARM SoCs.
A slew of changes this release cycle. The reset driver tree, that we
merge through arm-soc for historical reasons, is also sizable this
time around.
Among the changes:
- clps711x: Treewide changes to compatible strings, merged here for simplicity.
- Qualcomm: SCM firmware driver cleanups, move to platform driver
- ux500: Major cleanups, removal of old mach-specific infrastructure.
- Atmel external bus memory driver
- Move of brcmstb platform to the rest of bcm
- PMC driver updates for tegra, various fixes and improvements
- Samsung platform driver updates to support 64-bit Exynos platforms
- Reset controller cleanups moving to devm_reset_controller_register() APIs
- Reset controller driver for Amlogic Meson
- Reset controller driver for Hisilicon hi6220
- ARM SCPI power domain support"
* tag 'armsoc-drivers' of git://git.kernel.org/pub/scm/linux/kernel/git/arm/arm-soc: (100 commits)
ARM: ux500: consolidate base platform files
ARM: ux500: move soc_id driver to drivers/soc
ARM: ux500: call ux500_setup_id later
ARM: ux500: consolidate soc_device code in id.c
ARM: ux500: remove cpu_is_u* helpers
ARM: ux500: use CLK_OF_DECLARE()
ARM: ux500: move l2x0 init to .init_irq
mfd: db8500 stop passing around platform data
ASoC: ab8500-codec: remove platform data based probe
ARM: ux500: move ab8500_regulator_plat_data into driver
ARM: ux500: remove unused regulator data
soc: raspberrypi-power: add CONFIG_OF dependency
firmware: scpi: add CONFIG_OF dependency
video: clps711x-fb: Changing the compatibility string to match with the smallest supported chip
input: clps711x-keypad: Changing the compatibility string to match with the smallest supported chip
pwm: clps711x: Changing the compatibility string to match with the smallest supported chip
serial: clps711x: Changing the compatibility string to match with the smallest supported chip
irqchip: clps711x: Changing the compatibility string to match with the smallest supported chip
clocksource: clps711x: Changing the compatibility string to match with the smallest supported chip
clk: clps711x: Changing the compatibility string to match with the smallest supported chip
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu
Pull IOMMU updates from Joerg Roedel:
- big-endian support and preparation for defered probing for the Exynos
IOMMU driver
- simplifications in iommu-group id handling
- support for Mediatek generation one IOMMU hardware
- conversion of the AMD IOMMU driver to use the generic IOVA allocator.
This driver now also benefits from the recent scalability
improvements in the IOVA code.
- preparations to use generic DMA mapping code in the Rockchip IOMMU
driver
- device tree adaption and conversion to use generic page-table code
for the MSM IOMMU driver
- an iova_to_phys optimization in the ARM-SMMU driver to greatly
improve page-table teardown performance with VFIO
- various other small fixes and conversions
* tag 'iommu-updates-v4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/joro/iommu: (59 commits)
iommu/amd: Initialize dma-ops domains with 3-level page-table
iommu/amd: Update Alias-DTE in update_device_table()
iommu/vt-d: Return error code in domain_context_mapping_one()
iommu/amd: Use container_of to get dma_ops_domain
iommu/amd: Flush iova queue before releasing dma_ops_domain
iommu/amd: Handle IOMMU_DOMAIN_DMA in ops->domain_free call-back
iommu/amd: Use dev_data->domain in get_domain()
iommu/amd: Optimize map_sg and unmap_sg
iommu/amd: Introduce dir2prot() helper
iommu/amd: Implement timeout to flush unmap queues
iommu/amd: Implement flush queue
iommu/amd: Allow NULL pointer parameter for domain_flush_complete()
iommu/amd: Set up data structures for flush queue
iommu/amd: Remove align-parameter from __map_single()
iommu/amd: Remove other remains of old address allocator
iommu/amd: Make use of the generic IOVA allocator
iommu/amd: Remove special mapping code for dma_ops path
iommu/amd: Pass gfp-flags to iommu_map_page()
iommu/amd: Implement apply_dm_region call-back
iommu/amd: Create a list of reserved iova addresses
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux
Pull DeviceTree updates from Rob Herring:
- remove most of_platform_populate() calls in arch code. Now the DT
core code calls it in the default case and platforms only need to
call it if they have special needs
- use pr_fmt on all the DT core print statements
- CoreSight binding doc improvements to block name descriptions
- add dt_to_config script which can parse dts files and list
corresponding kernel config options
- fix memory leak hit with a PowerMac DT
- correct a bunch of STMicro compatible strings to use the correct
vendor prefix
- fix DA9052 PMIC binding doc to match what is actually used in dts
files
* tag 'devicetree-for-4.8' of git://git.kernel.org/pub/scm/linux/kernel/git/robh/linux: (35 commits)
documentation: da9052: Update regulator bindings names to match DA9052/53 DTS expectations
xtensa: Partially Revert "xtensa: Remove unnecessary of_platform_populate with default match table"
xtensa: Fix build error due to missing include file
MIPS: ath79: Add missing include file
Fix spelling errors in Documentation/devicetree
ARM: dts: fix STMicroelectronics compatible strings
powerpc/dts: fix STMicroelectronics compatible strings
Documentation: dt: i2c: use correct STMicroelectronics vendor prefix
scripts/dtc: dt_to_config - kernel config options for a devicetree
of: fdt: mark unflattened tree as detached
of: overlay: add resolver error prints
coresight: document binding acronyms
Documentation/devicetree: document cavium-pip rx-delay/tx-delay properties
of: use pr_fmt prefix for all console printing
of/irq: Mark initialised interrupt controllers as populated
of: fix memory leak related to safe_name()
Revert "of/platform: export of_default_bus_match_table"
of: unittest: use of_platform_default_populate() to populate default bus
memory: omap-gpmc: use of_platform_default_populate() to populate default bus
bus: uniphier-system-bus: use of_platform_default_populate() to populate default bus
...
|
|
'arm/msm', 'arm/rockchip', 'arm/smmu' and 'core' into next
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Merge "Samsung drivers/soc update for v4.8, part 3" into next/drivers:
1. Fix size of allocation for Exynos SROM registers (too much was allocated).
2. Constify fix.
* tag 'samsung-drivers-4.8-3' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
soc: samsung: pmu: Constify arrays with PMU data
memory: samsung: exynos-srom: Fix wrong count of registers
|
|
This patch enables IFC NAND support on ARM layerscape platform.
It fixes the dependency to enable NAND. The include files are being modified
to ensure complilation for both PowerPC and ARM architectures.
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Signed-off-by: Brian Norris <computersforpeace@gmail.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux into next/drivers
memory: tegra: Changes for v4.8-rc1
Contains three reference count fixes from coccinelle.
* tag 'tegra-for-4.8-memory' of git://git.kernel.org/pub/scm/linux/kernel/git/tegra/linux:
memory: tegra: mc: Add missing of_node_put()
memory: tegra: Delete unneeded of_node_put()
memory: tegra: tegra124-emc: Add missing of_node_put()
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
This patch fixes wrong count of array for SROM registers from probe
function.
Signed-off-by: Seung-Woo Kim <sw0312.kim@samsung.com>
Reviewed-by: Chanwoo Choi <cw00.choi@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux into next/drivers
Samsung drivers/soc update for v4.8, part 2:
1. Endian-friendly fixes.
2. Make SROMC driver explicitly non-module.
* tag 'samsung-drivers-4.8-2' of git://git.kernel.org/pub/scm/linux/kernel/git/krzk/linux:
cpufreq: s5pv210: use relaxed IO accesors
memory: samsung: exynos-srom: make it explicitly non-modular
memory: samsung: endian fixes for IO
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
next/drivers
OMAP-GPMC: driver updates for v4.8
* Make GPMC driver non modular as it is going to
be built-in only till arch/arm/mach-omap2 users
are removed.
* Fix build if CONFIG_OF is not defined.
* tag 'gpmc-omap-for-v4.8' of https://github.com/rogerq/linux:
memory: omap-gpmc: Move gpio functions out of #ifdef CONFIG_OF
memory: omap-gpmc: make it explicitly non-modular
Signed-off-by: Olof Johansson <olof@lixom.net>
|
|
Use helper of_platform_default_populate() in linux/of_platform
when possible, instead of calling of_platform_populate() with
the default match table.
Acked-by: Roger Quadros <rogerq@ti.com>
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Kefeng Wang <wangkefeng.wang@huawei.com>
Signed-off-by: Rob Herring <robh@kernel.org>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/memory/Kconfig:config ATMEL_EBI
drivers/memory/Kconfig: bool "Atmel EBI driver"
...meaning that it currently is not being built as a module by anyone.
Lets remove the few remaining modular references, so that when reading
the driver there is no doubt it is builtin-only.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Acked-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
The Kconfig for this option is currently:
config ATMEL_SDRAMC
bool "Atmel (Multi-port DDR-)SDRAM Controller"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modularity, so that when reading the
driver there is no doubt it is builtin-only.
Since module_init translates to device_initcall in the non-modular
case, the init ordering remains unchanged with this commit. An
alternate init level might be worth considering at a later date.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
was (or is now) contained at the top of the file in the comments.
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Nicolas Ferre <nicolas.ferre@atmel.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Mediatek SMI has two generations of HW architecture, mt8173 uses the
second generation of SMI HW while mt2701 uses the first generation
HW of SMI.
There's slight differences between the two generations, for generation 2,
the register which control the iommu port access PA or IOVA is at each
larb's register base. But for generation 1, the register is at smi ao
base(smi always on register base).
Besides that, the smi async clock should be prepared and enabled for SMI
generation 1 HW to transform the smi clock into emi clock domain, but is
not needed for SMI generation 2.
This patch add SMI driver for mt2701 which use generation 1 SMI HW.
Signed-off-by: Honghui Zhang <honghui.zhang@mediatek.com>
Signed-off-by: Joerg Roedel <jroedel@suse.de>
|
|
The Kconfig currently controlling compilation of this code is:
memory/samsung/Kconfig:config EXYNOS_SROM
memory/samsung/Kconfig: bool "Exynos SROM controller driver" if COMPILE_TEST
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
We explicitly disallow a driver unbind, since that doesn't have a
sensible use case anyway, and it allows us to drop the ".remove"
code for non-modular drivers.
Since module_platform_driver() uses the same init level priority as
builtin_platform_driver() the init ordering remains unchanged with
this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
Cc: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
Use the relaxed versions of the IO accessors to avoid any issues
if running in big endian.
Signed-off-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
The gpio related functions were mistakenly built only if CONFIG_OF
is defined. They are needed even otherwise and will cause build
failures if CONFIG_OF is not defined. Move the gpio functions
outside #ifdef CONFIG_OF.
Fixes: d2d00862dfbb ("memory: omap-gpmc: Support general purpose input for WAITPINs")
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/memory/Kconfig:config OMAP_GPMC
drivers/memory/Kconfig: bool
...meaning that it currently is not being built as a module by anyone.
Lets remove the modular code that is essentially orphaned, so that
when reading the driver there is no doubt it is builtin-only.
Since module_init was not in use by this code, the init ordering
remains unchanged with this commit.
Also note that MODULE_DEVICE_TABLE is a no-op for non-modular code.
We don't replace module.h with init.h since the file already has that.
Cc: Roger Quadros <rogerq@ti.com>
Cc: Tony Lindgren <tony@atomide.com>
Cc: linux-omap@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
|
|
In the omap gpmc driver it can be noticed that GPMC_CONFIG4_OEEXTRADELAY
is overwritten by the WEEXTRADELAY value from the device tree and
GPMC_CONFIG4_WEEXTRADELAY is not updated by the value from the device
tree.
As a consequence, the memory accesses cannot be configured properly when
the extra delay are needed for OE and WE.
Fix the update of GPMC_CONFIG4_WEEXTRADELAY with the value from the
device tree file and prevents GPMC_CONFIG4_OEXTRADELAY
being overwritten by the WEXTRADELAY value from the device tree.
Cc: stable@vger.kernel.org
Signed-off-by: Ocquidant, Sebastien <sebastienocquidant@eaton.com>
Signed-off-by: Roger Quadros <rogerq@ti.com>
|
|
for_each_child_of_node() performs an of_node_get() on each iteration, so
to break out of the loop an of_node_put() is required.
Found using Coccinelle. The semantic patch used for this is as follows:
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_child_of_node(..., n) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
for_each_child_of_node() performs an of_node_put() on each iteration, so
putting an of_node_put() before a continue results in a double put.
The semantic match that finds this problem is as follows
(http://coccinelle.lip6.fr):
// <smpl>
@@
expression root,e;
local idexpression child;
iterator name for_each_child_of_node;
@@
for_each_child_of_node(root, child) {
... when != of_node_get(child)
* of_node_put(child);
...
* continue;
}
// </smpl>
Signed-off-by: Julia Lawall <Julia.Lawall@lip6.fr>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
for_each_child_of_node() performs an of_node_get() on each iteration, so
to break out of the loop an of_node_put() is required.
Found using Coccinelle. The semantic patch used for this is as follows:
// <smpl>
@@
expression e;
local idexpression n;
@@
for_each_child_of_node(..., n) {
... when != of_node_put(n)
when != e = n
(
return n;
|
+ of_node_put(n);
? return ...;
)
...
}
// </smpl>
Signed-off-by: Amitoj Kaur Chawla <amitoj1606@gmail.com>
Signed-off-by: Thierry Reding <treding@nvidia.com>
|
|
The EBI (External Bus Interface) is used to access external peripherals
(NOR, SRAM, NAND, and other specific devices like ethernet controllers).
Each device is assigned a CS line and an address range and can have its
own configuration (timings, access mode, bus width, ...).
This driver provides a generic DT binding to configure a device according
to its requirements.
For specific device controllers (like the NAND one) the SMC timings
should be configured by the controller driver through the matrix and
smc syscon regmaps.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Signed-off-by: Alexandre Belloni <alexandre.belloni@free-electrons.com>
|
|
Pull MTD updates from Brian Norris:
"First cycle with Boris as NAND maintainer! Many (most) bullets stolen
from him.
Generic:
- Migrated NAND LED trigger to be a generic MTD trigger
NAND:
- Introduction of the "ECC algorithm" concept, to avoid overloading
the ECC mode field too much more
- Replaced the nand_ecclayout infrastructure with something a little
more flexible (finally!) and future proof
- Rework of the OMAP GPMC and NAND drivers; the TI folks pulled some
of this into their own tree as well
- Prepare the sunxi NAND driver to receive DMA support
- Handle bitflips in erased pages on GPMI revisions that do not
support this in hardware.
SPI NOR:
- Start using the spi_flash_read() API for SPI drivers that support
it (i.e., SPI drivers with special memory-mapped flash modes)
And other small scattered improvments"
* tag 'for-linus-20160523' of git://git.infradead.org/linux-mtd: (155 commits)
mtd: spi-nor: support GigaDevice gd25lq64c
mtd: nand_bch: fix spelling of "probably"
mtd: brcmnand: respect ECC algorithm set by NAND subsystem
gpmi-nand: Handle ECC Errors in erased pages
Documentation: devicetree: deprecate "soft_bch" nand-ecc-mode value
mtd: nand: add support for "nand-ecc-algo" DT property
mtd: mtd: drop NAND_ECC_SOFT_BCH enum value
mtd: drop support for NAND_ECC_SOFT_BCH as "soft_bch" mapping
mtd: nand: read ECC algorithm from the new field
mtd: nand: fsmc: validate ECC setup by checking algorithm directly
mtd: nand: set ECC algorithm to Hamming on fallback
staging: mt29f_spinand: set ECC algorithm explicitly
CRIS v32: nand: set ECC algorithm explicitly
mtd: nand: atmel: set ECC algorithm explicitly
mtd: nand: davinci: set ECC algorithm explicitly
mtd: nand: bf5xx: set ECC algorithm explicitly
mtd: nand: omap2: Fix high memory dma prefetch transfer
mtd: nand: omap2: Start dma request before enabling prefetch
mtd: nandsim: add __init attribute
mtd: nand: move of_get_nand_xxx() helpers into nand_base.c
...
|
|
Pull drm updates from Dave Airlie:
"Here's the main drm pull request for 4.7, it's been a busy one, and
I've been a bit more distracted in real life this merge window. Lots
more ARM drivers, not sure if it'll ever end. I think I've at least
one more coming the next merge window.
But changes are all over the place, support for AMD Polaris GPUs is in
here, some missing GM108 support for nouveau (found in some Lenovos),
a bunch of MST and skylake fixes.
I've also noticed a few fixes from Arnd in my inbox, that I'll try and
get in asap, but I didn't think they should hold this up.
New drivers:
- Hisilicon kirin display driver
- Mediatek MT8173 display driver
- ARC PGU - bitstreamer on Synopsys ARC SDP boards
- Allwinner A13 initial RGB output driver
- Analogix driver for DisplayPort IP found in exynos and rockchip
DRM Core:
- UAPI headers fixes and C++ safety
- DRM connector reference counting
- DisplayID mode parsing for Dell 5K monitors
- Removal of struct_mutex from drivers
- Connector registration cleanups
- MST robustness fixes
- MAINTAINERS updates
- Lockless GEM object freeing
- Generic fbdev deferred IO support
panel:
- Support for a bunch of new panels
i915:
- VBT refactoring
- PLL computation cleanups
- DSI support for BXT
- Color manager support
- More atomic patches
- GEM improvements
- GuC fw loading fixes
- DP detection fixes
- SKL GPU hang fixes
- Lots of BXT fixes
radeon/amdgpu:
- Initial Polaris support
- GPUVM/Scheduler/Clock/Power improvements
- ASYNC pageflip support
- New mesa feature support
nouveau:
- GM108 support
- Power sensor support improvements
- GR init + ucode fixes.
- Use GPU provided topology information
vmwgfx:
- Add host messaging support
gma500:
- Some cleanups and fixes
atmel:
- Bridge support
- Async atomic commit support
fsl-dcu:
- Timing controller for LCD support
- Pixel clock polarity support
rcar-du:
- Misc fixes
exynos:
- Pipeline clock support
- Exynoss4533 SoC support
- HW trigger mode support
- export HDMI_PHY clock
- DECON5433 fixes
- Use generic prime functions
- use DMA mapping APIs
rockchip:
- Lots of little fixes
vc4:
- Render node support
- Gamma ramp support
- DPI output support
msm:
- Mostly cleanups and fixes
- Conversion to generic struct fence
etnaviv:
- Fix for prime buffer handling
- Allow hangcheck to be coalesced with other wakeups
tegra:
- Gamme table size fix"
* 'drm-next' of git://people.freedesktop.org/~airlied/linux: (1050 commits)
drm/edid: add displayid detailed 1 timings to the modelist. (v1.1)
drm/edid: move displayid validation to it's own function.
drm/displayid: Iterate over all DisplayID blocks
drm/edid: move displayid tiled block parsing into separate function.
drm: Nuke ->vblank_disable_allowed
drm/vmwgfx: Report vmwgfx version to vmware.log
drm/vmwgfx: Add VMWare host messaging capability
drm/vmwgfx: Kill some lockdep warnings
drm/nouveau/gr/gf100-: fix race condition in fecs/gpccs ucode
drm/nouveau/core: recognise GM108 chipsets
drm/nouveau/gr/gm107-: fix touching non-existent ppcs in attrib cb setup
drm/nouveau/gr/gk104-: share implementation of ppc exception init
drm/nouveau/gr/gk104-: move rop_active_fbps init to nonctx
drm/nouveau/bios/pll: check BIT table version before trying to parse it
drm/nouveau/bios/pll: prevent oops when limits table can't be parsed
drm/nouveau/volt/gk104: round up in gk104_volt_set
drm/nouveau/fb/gm200: setup mmu debug buffer registers at init()
drm/nouveau/fb/gk20a,gm20b: setup mmu debug buffer registers at init()
drm/nouveau/fb/gf100-: allocate mmu debug buffers
drm/nouveau/fb: allow chipset-specific actions for oneinit()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc
Pull char / misc driver updates from Greg KH:
"Here's the big char and misc driver update for 4.7-rc1.
Lots of different tiny driver subsystems have updates here with new
drivers and functionality. Details in the shortlog.
All have been in linux-next with no reported issues for a while"
* tag 'char-misc-4.7-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/char-misc: (125 commits)
mcb: Delete num_cells variable which is not required
mcb: Fixed bar number assignment for the gdd
mcb: Replace ioremap and request_region with the devm version
mcb: Implement bus->dev.release callback
mcb: export bus information via sysfs
mcb: Correctly initialize the bus's device
mei: bus: call mei_cl_read_start under device lock
coresight: etb10: adjust read pointer only when needed
coresight: configuring ETF in FIFO mode when acting as link
coresight: tmc: implementing TMC-ETF AUX space API
coresight: moving struct cs_buffers to header file
coresight: tmc: keep track of memory width
coresight: tmc: make sysFS and Perf mode mutually exclusive
coresight: tmc: dump system memory content only when needed
coresight: tmc: adding mode of operation for link/sinks
coresight: tmc: getting rid of multiple read access
coresight: tmc: allocating memory when needed
coresight: tmc: making prepare/unprepare functions generic
coresight: tmc: splitting driver in ETB/ETF and ETR components
coresight: tmc: cleaning up header file
...
|
|
To allow building mediatek-drm.ko as a module, the
mtk_smi_larb_get and mtk_smi_larb_put symbols have
to be exported.
Signed-off-by: Philipp Zabel <p.zabel@pengutronix.de>
|
|
Presumably we never use the default: case statement which prints a
warning message. But my static checker complains that if we do, we will
hit an uninitialized variable warning.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
The core now takes care of parsing generic DT properties in
nand_scan_ident() when nand_set_flash_node() has been called.
Rely on this initialization instead of calling of_get_nand_xxx()
manually.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Roger Quadros <rogerq@ti.com>
Tested-by: Franklin S Cooper Jr. <fcooper@ti.com>
|
|
The new IFC controller version 2.0 has a different memory map page.
Upto IFC 1.4 PAGE size is 4 KB and from IFC2.0 PAGE size is 64KB.
This patch segregates the IFC global and runtime registers to appropriate
PAGE sizes.
Signed-off-by: Jaiprakash Singh <b44839@freescale.com>
Signed-off-by: Raghav Dogra <raghav@freescale.com>
Acked-by: Li Yang <leoyang.li@nxp.com>
Signed-off-by: Raghav Dogra <raghav.dogra@nxp.com>
Acked-by: Scott Wood <oss@buserror.net>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
|
|
Implement handling properties in subnodes and adding child devices to the
system. Child devices will not be added if configuration fails.
Since the driver now does more than suspend-resume support, dependency on
CONFIG_PM is removed.
Signed-off-by: Pavel Fedin <p.fedin@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
This patch adds Exynos SROM controller driver which will handle
save restore of SROM registers during S2R.
Signed-off-by: Pankaj Dubey <pankaj.dubey@samsung.com>
Reviewed-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
[p.fedin@samsung.com: tested on SMDK5410]
Tested-by: Pavel Fedin <p.fedin@samsung.com>
Signed-off-by: Kukjin Kim <kgene@kernel.org>
[k.kozlowski: Minor COMPILE_TEST adjustments in Kconfig entries]
Signed-off-by: Krzysztof Kozlowski <k.kozlowski@samsung.com>
|
|
GPMC_STATUS register is private to the GPMC module and must not be
accessed directly by NAND driver through the gpmc_regs.
They must use gpmc_omap_get_nand_ops() instead.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAPs can have 2 to 4 WAITPINs that can be used as edge triggered
interrupts if not used for memory wait state insertion.
Support these interrupts via the gpmc IRQ domain.
The gpmc IRQ domain interrupt map is:
0 - NAND_fifoevent
1 - NAND_termcount
2 - GPMC_WAIT0 edge
3 - GPMC_WAIT1 edge, and so on
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
If the device attached to GPMC wants to use the WAIT pin
for WAIT monitoring then we reserve it internally for
exclusive use.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
OMAPs can have 2 to 4 WAITPINs that can be used as general purpose
input if not used for memory wait state insertion.
The first user will be the OMAP NAND chip to get the NAND
read/busy status using gpiolib.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
We have been preventing mapping GPMC children in the
first 1MB but really it has to be the first 16MB as
the minimum GPMC partition size is 16MB.
Also print an error message if CS mapping fails
due to DT requesting address outside the GPMC
map.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
|
Move NAND specific device tree parsing to NAND driver.
The NAND controller node must have a compatible id, register space
resource and interrupt resource.
Signed-off-by: Roger Quadros <rogerq@ti.com>
Acked-by: Brian Norris <computersforpeace@gmail.com>
Acked-by: Tony Lindgren <tony@atomide.com>
|
