| Age | Commit message (Collapse) | Author |
|---|
|
This protocol responds to a real philips rc-mm remote; it does not respond
to IR encoded with the encoder in ir-rcmm-decoder.c.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In cx24117_load_firmware(), 'buf' is allocated through kmalloc() to hold
the firmware. However, if i2c_transfer() fails, it is not deallocated,
leading to a memory leak bug.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In dib7000pc_detection(), 'tx' and 'rx' are allocated through kzalloc()
respectively. However, if DiB7000PC is detected, they are not deallocated,
leading to memory leaks. To fix this issue, create a label to free 'tx' and
'rx' before returning from the function.
Signed-off-by: Wenwen Wang <wenwen@cs.uga.edu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Fix and eliminate mceusb's IR length limit for IR signals transmitted to
the MCE IR blaster ports.
An IR signal TX exceeding 306 pulse/space samples presently causes -EINVAL
return error. There's no such limitation nor error with the MCE device
hardware. And valid IR signals exist with more than 400 pulse/space for the
control of certain appliances (eg Panasonic ACXA75C00600 air conditioner).
The scope of this patch is limited to the mceusb driver. There are still
IR signal TX length and time constraints that related modules of rc core
(eg LIRC) impose, further up the driver stack.
Changes for mceusb_tx_ir():
Converts and sends LIRC IR pulse/space sequence to MCE device IR
pulse/space format.
Break long length LIRC sequence into multiple (unlimited number of) parts
for sending to the MCE device.
Reduce kernel stack IR buffer size: 128 (was 384)
Increase MCE IR data packet size: 31 (was 5)
Zero time LIRC pulse/space no longer copied to MCE IR data.
Eliminate overwriting the source/input LIRC IR data in txbuf[].
Eliminate -EINVAL return; return number of IR samples sent (>0) or
MCE write error code (<0).
New mce_write() and mce_write_callback():
Implements synchronous blocking I/O, with timeout, for writing/sending
data to the MCE device.
An unlimited multipart IR signal sent to the MCE device faster than real
time requires flow control absent with the original mce_request_packet()
and mce_async_callback() asynchronous I/O implementation. Also absent is
TX error feedback.
mce_write() combines and replaces mce_request_packet() and
mce_async_callback() with conversion to synchronous I/O.
mce_write() returns bytes sent (>0) or MCE device write error (<0).
Debug hex dump TX data before processing.
Rename mce_async_out() -> mce_command_out():
The original name is misleading with underlying synchronous I/O
implementation. Function renamed to mce_command_out().
Changes in mceusb_handle_command():
Add support for MCE device error case MCE_RSP_TX_TIMEOUT
"IR TX timeout (TX buffer underrun)"
Changes in mceusb_dev_printdata():
Changes support test and debug of multipart TX IR.
Add buffer boundary information (offset and buffer size) to TX hex dump.
Correct TX trace bug "Raw IR data, 0 pulse/space samples"
Add trace for MCE_RSP_TX_TIMEOUT "IR TX timeout (TX buffer underrun)"
Other changes:
The driver's write to USB device architecture change (async to sync I/O)
is significant so we bump DRIVER_VERSION to "1.95" (from "1.94").
Tests:
$ cat -n irdata1 | head -3
1 carrier 36000
2 pulse 6350
3 space 6350
$ cat -n irdata1 | tail -3
76 pulse 6350
77 space 6350
78 pulse 6350
$ ir-ctl -s irdata1
[1549021.073612] mceusb 1-1.3:1.0: requesting 36000 HZ carrier
[1549021.073635] mceusb 1-1.3:1.0: tx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.073649] mceusb 1-1.3:1.0: Request carrier of 35714 Hz (period 28us)
[1549021.073848] mceusb 1-1.3:1.0: tx done status = 4 (wait = 100, expire = 100 (1000ms), urb->actual_length = 4, urb->status = 0)
[1549021.074689] mceusb 1-1.3:1.0: rx data[0]: 9f 06 01 45 (len=4 sz=4)
[1549021.074701] mceusb 1-1.3:1.0: Got carrier of 35714 Hz (period 28us)
[1549021.102023] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549021.102036] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549021.102219] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549021.131979] mceusb 1-1.3:1.0: tx data[0]: 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 9e ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f ff 7f 91 ff (len=81 sz=81)
[1549021.131992] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549021.133592] mceusb 1-1.3:1.0: tx done status = 81 (wait = 100, expire = 100 (1000ms), urb->actual_length = 81, urb->status = 0)
Hex dumps limited to 64 bytes.
0xff is MCE maximum time pulse, 0x7f is MCE maximum time space.
$ cat -n irdata2 | head -3
1 carrier 36000
2 pulse 50
3 space 50
$ cat -n irdata2 | tail -3
254 pulse 50
255 space 50
256 pulse 50
$ ir-ctl -s irdata2
[1549306.586998] mceusb 1-1.3:1.0: tx data[0]: 9f 08 03 (len=3 sz=3)
[1549306.587015] mceusb 1-1.3:1.0: Request transmit blaster mask of 0x03
[1549306.587252] mceusb 1-1.3:1.0: tx done status = 3 (wait = 100, expire = 100 (1000ms), urb->actual_length = 3, urb->status = 0)
[1549306.613275] mceusb 1-1.3:1.0: tx data[0]: 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 9e 81 (len=128 sz=128)
[1549306.613291] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.614837] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.614861] mceusb 1-1.3:1.0: tx data[0]: 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 01 81 9e 01 (len=128 sz=128)
[1549306.614869] mceusb 1-1.3:1.0: Raw IR data, 30 pulse/space samples
[1549306.620199] mceusb 1-1.3:1.0: tx done status = 128 (wait = 100, expire = 100 (1000ms), urb->actual_length = 128, urb->status = 0)
[1549306.620212] mceusb 1-1.3:1.0: tx data[0]: 89 81 01 81 01 81 01 81 01 81 80 (len=11 sz=11)
[1549306.620221] mceusb 1-1.3:1.0: Raw IR data, 9 pulse/space samples
[1549306.633294] mceusb 1-1.3:1.0: tx done status = 11 (wait = 98, expire = 100 (1000ms), urb->actual_length = 11, urb->status = 0)
Hex dumps limited to 64 bytes.
0x81 is MCE minimum time pulse, 0x01 is MCE minimum time space.
TX IR part 3 sz=11 shows 20msec I/O blocking delay
(100expire - 98wait = 2jiffies)
Signed-off-by: A Sun <as1033x@comcast.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This is a simple NEC remote control device shipped with the HardKernel
ODROID range of SBC devices.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The WeTek Play 2 Android STB ships with an unusual remote where the
main up/down/left/right/enter controls are surrounded with an outer
ring of additional keys which are listed in clockwise order.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The WeTek Hub Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The Tanix TX5 max Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The Tanix TX3 mini Android STB ships with a simple NEC remote.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Khadas VIM and Edge SBC devices use the same NEC remote device. The
remote includes a mouse button for Android use. This has been mapped
to KEY_MUTE.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The X96-Max Android STB ships with a simple NEC remote. It includes
a TV section with preset buttons for controlling a TV. These are not
configurable, but are noted to aid visual recognition of the device.
Signed-off-by: Christian Hewitt <christianshewitt@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Use cmd_init() to fill a struct si2168_cmd command.
Signed-off-by: Marc Gonzalez <marc.w.gonzalez@free.fr>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
KASAN: global-out-of-bounds Read in dvb_pll_attach
Syzbot reported global-out-of-bounds Read in dvb_pll_attach, while
accessing id[dvb_pll_devcount], because dvb_pll_devcount was 65,
that is more than size of 'id' which is DVB_PLL_MAX(64).
Rather than increasing dvb_pll_devcount every time, use ida so that
numbers are allocated correctly. This does mean that no more than
64 devices can be attached at the same time, but this is more than
sufficient.
usb 1-1: dvb_usb_v2: will pass the complete MPEG2 transport stream to the
software demuxer
dvbdev: DVB: registering new adapter (774 Friio White ISDB-T USB2.0)
usb 1-1: media controller created
dvbdev: dvb_create_media_entity: media entity 'dvb-demux' registered.
tc90522 0-0018: Toshiba TC90522 attached.
usb 1-1: DVB: registering adapter 0 frontend 0 (Toshiba TC90522 ISDB-T
module)...
dvbdev: dvb_create_media_entity: media entity 'Toshiba TC90522 ISDB-T
module' registered.
==================================================================
BUG: KASAN: global-out-of-bounds in dvb_pll_attach+0x6c5/0x830
drivers/media/dvb-frontends/dvb-pll.c:798
Read of size 4 at addr ffffffff89c9e5e0 by task kworker/0:1/12
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.2.0-rc6+ #13
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
print_address_description+0x67/0x231 mm/kasan/report.c:188
__kasan_report.cold+0x1a/0x32 mm/kasan/report.c:317
kasan_report+0xe/0x20 mm/kasan/common.c:614
dvb_pll_attach+0x6c5/0x830 drivers/media/dvb-frontends/dvb-pll.c:798
dvb_pll_probe+0xfe/0x174 drivers/media/dvb-frontends/dvb-pll.c:877
i2c_device_probe+0x790/0xaa0 drivers/i2c/i2c-core-base.c:389
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
i2c_new_client_device+0x5b3/0xc40 drivers/i2c/i2c-core-base.c:778
i2c_new_device+0x19/0x50 drivers/i2c/i2c-core-base.c:821
dvb_module_probe+0xf9/0x220 drivers/media/dvb-core/dvbdev.c:985
friio_tuner_attach+0x125/0x1d0 drivers/media/usb/dvb-usb-v2/gl861.c:536
dvb_usbv2_adapter_frontend_init
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:675 [inline]
dvb_usbv2_adapter_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:804
[inline]
dvb_usbv2_init drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:865 [inline]
dvb_usbv2_probe.cold+0x24dc/0x255d
drivers/media/usb/dvb-usb-v2/dvb_usb_core.c:980
usb_probe_interface+0x305/0x7a0 drivers/usb/core/driver.c:361
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_set_configuration+0xdf6/0x1670 drivers/usb/core/message.c:2023
generic_probe+0x9d/0xd5 drivers/usb/core/generic.c:210
usb_probe_device+0x99/0x100 drivers/usb/core/driver.c:266
really_probe+0x281/0x660 drivers/base/dd.c:509
driver_probe_device+0x104/0x210 drivers/base/dd.c:670
__device_attach_driver+0x1c2/0x220 drivers/base/dd.c:777
bus_for_each_drv+0x15c/0x1e0 drivers/base/bus.c:454
__device_attach+0x217/0x360 drivers/base/dd.c:843
bus_probe_device+0x1e4/0x290 drivers/base/bus.c:514
device_add+0xae6/0x16f0 drivers/base/core.c:2111
usb_new_device.cold+0x8c1/0x1016 drivers/usb/core/hub.c:2534
hub_port_connect drivers/usb/core/hub.c:5089 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5204 [inline]
port_event drivers/usb/core/hub.c:5350 [inline]
hub_event+0x1ada/0x3590 drivers/usb/core/hub.c:5432
process_one_work+0x905/0x1570 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
kthread+0x30b/0x410 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
The buggy address belongs to the variable:
id+0x100/0x120
Memory state around the buggy address:
ffffffff89c9e480: fa fa fa fa 00 00 fa fa fa fa fa fa 00 00 00 00
ffffffff89c9e500: 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00 00
> ffffffff89c9e580: 00 00 00 00 00 00 00 00 00 00 00 00 fa fa fa fa
^
ffffffff89c9e600: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
ffffffff89c9e680: 04 fa fa fa fa fa fa fa 04 fa fa fa fa fa fa fa
==================================================================
Reported-by: syzbot+8a8f48672560c8ca59dd@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Tag all the coded formats where the vicodec stateful decoder supports
dynamic resolution switching and bytestream parsing.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Tag all the coded formats where the mtk-vcodec decoder supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Reviewed-by: Alexandre Courbot <acourbot@chromium.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Tag all the coded formats where the venus vdec supports dynamic
resolution switching.
Signed-off-by: Maxime Jourdan <mjourdan@baylibre.com>
Acked-by: Stanimir Varbanov <stanimir.varbanov@linaro.org>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Stateless decoders have different expectations about the
start code that is prepended on H264 slices. Add a
menu control to express the supported start code types
(including no start code).
Drivers are allowed to support only one start code type,
but they can support both too.
Note that this is independent of the H264 decoding mode,
which specifies the granularity of the decoding operations.
Either in frame-based or slice-based mode, this new control
will allow to define the start code expected on H264 slices.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Some stateless decoders don't support per-slice decoding granularity
(or at least not in a way that would make them efficient or easy to use).
Expose a menu to control the supported decoding modes. Drivers are
allowed to support only one decoding but they can support both too.
To fully specify the decoding operation, we need to introduce
a start_byte_offset, to indicate where slices start.
Signed-off-by: Boris Brezillon <boris.brezillon@collabora.com>
Reviewed-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The V4L2_PIX_FMT_H264_SLICE_RAW name was originally suggested
because the pixel format would represent H264 slices without any
start code.
However, as we will now introduce a start code menu control,
give the pixel format a more meaningful name, while it's
still early enough to do so.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Tested-by: Philipp Zabel <p.zabel@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If reg_r() fails, then gspca_dev->usb_buf was left uninitialized,
and some drivers used the contents of that buffer in logic.
This caused several syzbot errors:
https://syzkaller.appspot.com/bug?extid=397fd082ce5143e2f67d
https://syzkaller.appspot.com/bug?extid=1a35278dd0ebfb3a038a
https://syzkaller.appspot.com/bug?extid=06ddf1788cfd048c5e82
I analyzed the gspca drivers and zeroed the buffer where needed.
Reported-and-tested-by: syzbot+1a35278dd0ebfb3a038a@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+397fd082ce5143e2f67d@syzkaller.appspotmail.com
Reported-and-tested-by: syzbot+06ddf1788cfd048c5e82@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
dev->usbc_buf was passed as argument for %s, but it was not safeguarded
by a terminating 0.
This caused this syzbot issue:
https://syzkaller.appspot.com/bug?extid=79d18aac4bf1770dd050
Reported-and-tested-by: syzbot+79d18aac4bf1770dd050@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In the probe() function radio->int_in_urb was not killed if an
error occurred in the probe sequence. It was also missing in
the disconnect.
This caused this syzbot issue:
https://syzkaller.appspot.com/bug?extid=2d4fc2a0c45ad8da7e99
Reported-and-tested-by: syzbot+2d4fc2a0c45ad8da7e99@syzkaller.appspotmail.com
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add support of several sub-devices within pipeline instead
of a single one.
This allows to support a CSI-2 camera sensor connected
through a CSI-2 to parallel bridge.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add media controller support to dcmi in order
to walk within remote subdevices pipeline.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a trace of the set of supported fourcc/mbus_code which
intersect between DCMI and source sub-device.
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Rename "subdev" entity struct field to "source"
to prepare for several subdev support.
Move asd field on top of entity struct.
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hugues Fruchet <hugues.fruchet@st.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Fix typos.
Signed-off-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
git://git.infradead.org/users/vkoul/slave-dma
Pull dmaengine fixes from Vinod Koul:
"Fixes in dmaengine drivers for:
- dw-edma: endianess, _iomem type and stack usages
- ste_dma40: unneeded variable and null-pointer dereference
- tegra210-adma: unused function
- omap-dma: off-by-one fix"
* tag 'dmaengine-fix-5.3-rc5' of git://git.infradead.org/users/vkoul/slave-dma:
omap-dma/omap_vout_vrfb: fix off-by-one fi value
dmaengine: stm32-mdma: Fix a possible null-pointer dereference in stm32_mdma_irq_handler()
dmaengine: tegra210-adma: Fix unused function warnings
dmaengine: ste_dma40: fix unneeded variable warning
dmaengine: dw-edma: fix endianess confusion
dmaengine: dw-edma: fix __iomem type confusion
dmaengine: dw-edma: fix unnecessary stack usage
|
|
This is mostly a port of Jacopo's fix:
commit aa4bb8b8838ffcc776a79f49a4d7476b82405349
Author: Jacopo Mondi <jacopo@jmondi.org>
Date: Fri Jul 6 05:51:52 2018 -0400
media: ov5640: Re-work MIPI startup sequence
In the OV5645 case, the changes are:
- At set_power(1) time power up MIPI Tx/Rx and set data and clock lanes in
LP11 during 'sleep' and 'idle' with MIPI clock in non-continuous mode.
- At set_power(0) time power down MIPI Tx/Rx (in addition to the current
power down of regulators and clock gating).
- At s_stream time enable/disable the MIPI interface output.
With this commit the sensor is able to enter LP-11 mode during power up,
as expected by some CSI-2 controllers.
Many thanks to Fabio Estevam for his help debugging this issue.
Tested-by: Fabio Estevam <festevam@gmail.com>
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The streaming state should be set to the first upstream sub-device only,
not everywhere, for a sub-device driver itself knows how to best control
the streaming state of its own upstream sub-devices.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The omap3isp driver registered subdevs without the dev field being set. Do
that now.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Luca Weiss <luca@z3ntu.xyz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Instead of blindly trusting getting the clock frequency succeeded end then
testing it against a pre-defined value, verify reading the value
succeeded.
Fixes: 879347f0c258 ("media: ov8856: Add support for OV8856 sensor")
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Currently when the call vsp1_dl_body_get fails and returns null the
error return path leaks the allocation of dl. Fix this by kfree'ing
dl before returning.
Addresses-Coverity: ("Resource leak")
Fixes: 5d7936b8e27d ("media: vsp1: Convert display lists to use new body pool")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In the general move to have i2c_new_*_device functions which return
ERR_PTR instead of NULL, this patch converts i2c_new_secondary_device().
There are only few users, so this patch converts the I2C core and all
users in one go. The function gets renamed to i2c_new_ancillary_device()
so out-of-tree users will get a build failure to understand they need to
adapt their error checking code.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com> # adv748x
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com> # adv7511 + adv7604
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # adv7604
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>
|
|
Allow selecting the IR protocol, MCE or iMON, for a device that
identifies as follows (with config id 0x7e):
15c2:ffdc SoundGraph Inc. iMON PAD Remote Controller
As the driver is structured to default to iMON when both RC
protocols are supported, existing users of this device (using MCE
protocol) will need to manually switch to MCE (RC-6) protocol from
userspace (with ir-keytable, sysfs).
Signed-off-by: Darius Rad <alpha@area49.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The usb_bulk_urb will kfree'd on disconnect, so ensure the pointer is set
to NULL after each free.
stop stream
urb killing
urb buffer free
tm6000: got start feed request tm6000_start_feed
tm6000: got start stream request tm6000_start_stream
tm6000: pipe reset
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: got start feed request tm6000_start_feed
tm6000: IR URB failure: status: -71, length 0
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
xhci_hcd 0000:00:14.0: ERROR unknown event type 37
tm6000: error tm6000_urb_received
usb 1-2: USB disconnect, device number 5
tm6000: disconnecting tm6000 #0
==================================================================
BUG: KASAN: use-after-free in dvb_fini+0x75/0x140 [tm6000_dvb]
Read of size 8 at addr ffff888241044060 by task kworker/2:0/22
CPU: 2 PID: 22 Comm: kworker/2:0 Tainted: G W 5.3.0-rc4+ #1
Hardware name: LENOVO 20KHCTO1WW/20KHCTO1WW, BIOS N23ET65W (1.40 ) 07/02/2019
Workqueue: usb_hub_wq hub_event
Call Trace:
dump_stack+0x9a/0xf0
print_address_description.cold+0xae/0x34f
__kasan_report.cold+0x75/0x93
? tm6000_fillbuf+0x390/0x3c0 [tm6000_alsa]
? dvb_fini+0x75/0x140 [tm6000_dvb]
kasan_report+0xe/0x12
dvb_fini+0x75/0x140 [tm6000_dvb]
tm6000_close_extension+0x51/0x80 [tm6000]
tm6000_usb_disconnect.cold+0xd4/0x105 [tm6000]
usb_unbind_interface+0xe4/0x390
device_release_driver_internal+0x121/0x250
bus_remove_device+0x197/0x260
device_del+0x268/0x550
? __device_links_no_driver+0xd0/0xd0
? usb_remove_ep_devs+0x30/0x3b
usb_disable_device+0x122/0x400
usb_disconnect+0x153/0x430
hub_event+0x800/0x1e40
? trace_hardirqs_on_thunk+0x1a/0x20
? hub_port_debounce+0x1f0/0x1f0
? retint_kernel+0x10/0x10
? lock_is_held_type+0xf1/0x130
? hub_port_debounce+0x1f0/0x1f0
? process_one_work+0x4ae/0xa00
process_one_work+0x4ba/0xa00
? pwq_dec_nr_in_flight+0x160/0x160
? do_raw_spin_lock+0x10a/0x1d0
worker_thread+0x7a/0x5c0
? process_one_work+0xa00/0xa00
kthread+0x1d5/0x200
? kthread_create_worker_on_cpu+0xd0/0xd0
ret_from_fork+0x3a/0x50
Allocated by task 2682:
save_stack+0x1b/0x80
__kasan_kmalloc.constprop.0+0xc2/0xd0
usb_alloc_urb+0x28/0x60
tm6000_start_feed+0x10a/0x300 [tm6000_dvb]
dmx_ts_feed_start_filtering+0x86/0x120 [dvb_core]
dvb_dmxdev_start_feed+0x121/0x180 [dvb_core]
dvb_dmxdev_filter_start+0xcb/0x540 [dvb_core]
dvb_demux_do_ioctl+0x7ed/0x890 [dvb_core]
dvb_usercopy+0x97/0x1f0 [dvb_core]
dvb_demux_ioctl+0x11/0x20 [dvb_core]
do_vfs_ioctl+0x5d8/0x9d0
ksys_ioctl+0x5e/0x90
__x64_sys_ioctl+0x3d/0x50
do_syscall_64+0x74/0xe0
entry_SYSCALL_64_after_hwframe+0x49/0xbe
Freed by task 22:
save_stack+0x1b/0x80
__kasan_slab_free+0x12c/0x170
kfree+0xfd/0x3a0
xhci_giveback_urb_in_irq+0xfe/0x230
xhci_td_cleanup+0x276/0x340
xhci_irq+0x1129/0x3720
__handle_irq_event_percpu+0x6e/0x420
handle_irq_event_percpu+0x6f/0x100
handle_irq_event+0x55/0x84
handle_edge_irq+0x108/0x3b0
handle_irq+0x2e/0x40
do_IRQ+0x83/0x1a0
Cc: stable@vger.kernel.org
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
KEY_MAX is not a key but designates the highest value a linux keycode
can ever have.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
syzbot reports an error on flush_request_modules() for the second device.
This workqueue was never initialised so simply remove the offending line.
usb 1-1: USB disconnect, device number 2
em28xx 1-1:1.153: Disconnecting em28xx #1
------------[ cut here ]------------
WARNING: CPU: 0 PID: 12 at kernel/workqueue.c:3031
__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Kernel panic - not syncing: panic_on_warn set ...
CPU: 0 PID: 12 Comm: kworker/0:1 Not tainted 5.3.0-rc2+ #25
Hardware name: Google Google Compute Engine/Google Compute Engine, BIOS
Google 01/01/2011
Workqueue: usb_hub_wq hub_event
Call Trace:
__dump_stack lib/dump_stack.c:77 [inline]
dump_stack+0xca/0x13e lib/dump_stack.c:113
panic+0x2a3/0x6da kernel/panic.c:219
__warn.cold+0x20/0x4a kernel/panic.c:576
report_bug+0x262/0x2a0 lib/bug.c:186
fixup_bug arch/x86/kernel/traps.c:179 [inline]
fixup_bug arch/x86/kernel/traps.c:174 [inline]
do_error_trap+0x12b/0x1e0 arch/x86/kernel/traps.c:272
do_invalid_op+0x32/0x40 arch/x86/kernel/traps.c:291
invalid_op+0x23/0x30 arch/x86/entry/entry_64.S:1026
RIP: 0010:__flush_work.cold+0x2c/0x36 kernel/workqueue.c:3031
Code: 9a 22 00 48 c7 c7 20 e4 c5 85 e8 d9 3a 0d 00 0f 0b 45 31 e4 e9 98 86
ff ff e8 51 9a 22 00 48 c7 c7 20 e4 c5 85 e8 be 3a 0d 00 <0f> 0b 45 31 e4
e9 7d 86 ff ff e8 36 9a 22 00 48 c7 c7 20 e4 c5 85
RSP: 0018:ffff8881da20f720 EFLAGS: 00010286
RAX: 0000000000000024 RBX: dffffc0000000000 RCX: 0000000000000000
RDX: 0000000000000000 RSI: ffffffff8128a0fd RDI: ffffed103b441ed6
RBP: ffff8881da20f888 R08: 0000000000000024 R09: fffffbfff11acd9a
R10: fffffbfff11acd99 R11: ffffffff88d66ccf R12: 0000000000000000
R13: 0000000000000001 R14: ffff8881c6685df8 R15: ffff8881d2a85b78
flush_request_modules drivers/media/usb/em28xx/em28xx-cards.c:3325 [inline]
em28xx_usb_disconnect.cold+0x280/0x2a6
drivers/media/usb/em28xx/em28xx-cards.c:4023
usb_unbind_interface+0x1bd/0x8a0 drivers/usb/core/driver.c:423
__device_release_driver drivers/base/dd.c:1120 [inline]
device_release_driver_internal+0x404/0x4c0 drivers/base/dd.c:1151
bus_remove_device+0x2dc/0x4a0 drivers/base/bus.c:556
device_del+0x420/0xb10 drivers/base/core.c:2288
usb_disable_device+0x211/0x690 drivers/usb/core/message.c:1237
usb_disconnect+0x284/0x8d0 drivers/usb/core/hub.c:2199
hub_port_connect drivers/usb/core/hub.c:4949 [inline]
hub_port_connect_change drivers/usb/core/hub.c:5213 [inline]
port_event drivers/usb/core/hub.c:5359 [inline]
hub_event+0x1454/0x3640 drivers/usb/core/hub.c:5441
process_one_work+0x92b/0x1530 kernel/workqueue.c:2269
process_scheduled_works kernel/workqueue.c:2331 [inline]
worker_thread+0x7ab/0xe20 kernel/workqueue.c:2417
kthread+0x318/0x420 kernel/kthread.c:255
ret_from_fork+0x24/0x30 arch/x86/entry/entry_64.S:352
Kernel Offset: disabled
Rebooting in 86400 seconds..
Fixes: be7fd3c3a8c5e ("media: em28xx: Hauppauge DualHD second tuner functionality)
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Reviewed-by: Brad Love <brad@nextdimension.cc>
Reported-by: syzbot+b7f57261c521087d89bb@syzkaller.appspotmail.com
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Sometimes the device sends IR data which is all space, no pulses
whatsoever. Add the end of this the driver will put the rc device into
idle mode when it already is in idle mode. The following will be logged:
rc rc0: nonsensical timing event of duration 0
rc rc0: two consecutive events of type space
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This code needs some explanation.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Convert this driver to use the new i2c_new_dummy_device() call and bail
out if the dummy device cannot be registered to make failure more
visible to the user.
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
ad_div
The variables mclk, div and ad_div are being assigned with a values
that are never read and are being updated later with a new values.
The assignments are redundant and can be removed.
Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
kmemdup is introduced to duplicate a region of memory in a neat way.
Rather than kmalloc/kzalloc + memcpy, which the programmer needs to
write the size twice (sometimes lead to mistakes), kmemdup improves
readability, leads to smaller code and also reduce the chances of mistakes.
Suggestion to use kmemdup rather than using kmalloc/kzalloc + memcpy.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Reviewed-by: Sylwester Nawrocki <s.nawrocki@samsung.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
pci_alloc_consistent calls dma_alloc_coherent directly.
In commit 518a2f1925c3
("dma-mapping: zero memory returned from dma_alloc_*"),
dma_alloc_coherent has already zeroed the memory.
So memset is not needed.
Signed-off-by: Fuqian Huang <huangfq.daxian@gmail.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
