| Age | Commit message (Collapse) | Author |
|---|
|
HVR-950Q uses an I2C remote controller at address 0x47 (7-bits
notation). Add support for it.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Commits 21dc61d3c0a4 and 7a1dd50b89d4 reduced the board I2C
speed to 20 MHz by default, due to a I2C stretch issue:
while xc5000 uses i2c stretch when a command is sent to it,
au0828 doesn't support this feature.
However, this is needed only for Xceive tuners. The other
I2C devices can work at the max speed.
So, revert the workarounds at board level, handling it at
I2C level, only when talking with xc5000.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
DViCO FusionHDTV7 device that use au0828 can fail to communicate with
xc5000 using i2c interface because of high i2c clock speed - i2c clock
stretching bug. It causes to fail xc5000 firmware loading normally at
the current driver.
Already this problem fixed as changing to low i2c clock speed at
HVR-950q device, also DViCO FusionHDTV7 device can solve it as using low
i2c clock speed - 20KHz.
Signed-off-by: Joonyoung Shim <jy0922.shim@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Restructure the way we bring the various GPIOs out of reset. In particular:
1. we only need to setup the GPIOs as outputs once
2. there's no point in writing 0x40 to register 0x00 since that's the EEPROM
write protect and already it's configured as an input
3. Separate out the act of enabling the power supply and bringing the tuner
and demod out of reset. If you don't then the chip may not be properly
enabled (as the power supply is still ramping up when the chip comes
out of reset). This can result in probing failures.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
This kind of memcpy() is error-prone. Its replacement with a struct
assignment is prefered because it's type-safe and much easier to read.
Found by coccinelle. Hand patched and reviewed.
Tested by compilation only.
A simplified version of the semantic match that finds this problem is as
follows: (http://coccinelle.lip6.fr/)
// <smpl>
@@
identifier struct_name;
struct struct_name to;
struct struct_name from;
expression E;
@@
-memcpy(&(to), &(from), E);
+to = from;
// </smpl>
Signed-off-by: Peter Senna Tschudin <peter.senna@gmail.com>
Signed-off-by: Ezequiel Garcia <elezegarcia@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Pull the analog frontend setup code out of au0828_card_setup into its
own seperate function, au0828_card_analog_fe_setup().
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch removes the dependendency of VIDEO_AU0828 on VIDEO_V4L2 by
creating a new Kconfig option, VIDEO_AU0828_V4L2, which enables analog
video capture support and depends on VIDEO_V4L2 itself.
With VIDEO_AU0828_V4L2 disabled, the driver will only support digital
television and will not depend on the v4l2-core. With VIDEO_AU0828_V4L2
enabled, the driver will be built with the analog v4l2 support included.
By default, the VIDEO_AU0828_V4L2 option will be set to Y, so as to
preserve the original behavior.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/usb/au0828/au0828-cards.c:28:6: warning: no previous prototype for 'hvr950q_cs5340_audio' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:161:6: warning: no previous prototype for 'au0828_uninit_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:200:5: warning: no previous prototype for 'au0828_init_isoc' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:786:5: warning: no previous prototype for 'au0828_analog_stream_enable' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:813:6: warning: no previous prototype for 'au0828_analog_stream_reset' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:916:6: warning: no previous prototype for 'au0828_vid_buffer_timeout' [-Wmissing-prototypes]
drivers/media/usb/au0828/au0828-video.c:940:6: warning: no previous prototype for 'au0828_vbi_buffer_timeout' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rename all USB drivers with their own directory under
drivers/media/video into drivers/media/usb and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
