| Age | Commit message (Collapse) | Author |
|---|
|
If the lirc device supports it, set the carrier for the protocol.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This introduces a new lirc mode: scancode. Any device which can send raw IR
can now also send scancodes.
int main()
{
int mode, fd = open("/dev/lirc0", O_RDWR);
mode = LIRC_MODE_SCANCODE;
if (ioctl(fd, LIRC_SET_SEND_MODE, &mode)) {
// kernel too old or lirc does not support transmit
}
struct lirc_scancode scancode = {
.scancode = 0x1e3d,
.rc_proto = RC_PROTO_RC5,
};
write(fd, &scancode, sizeof(scancode));
close(fd);
}
The other fields of lirc_scancode must be set to 0.
Note that toggle (rc5, rc6) and repeats (nec) are not implemented. Nor is
there a method for holding down a key for a period.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
LIRCCODE is a lirc mode where a driver produces driver-dependent
codes for receive and transmit. No driver uses this any more. The
LIRC_GET_LENGTH ioctl was used for this mode only.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
As we're now using SPDX identifiers, on the several
RC keymap files I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to identify GPL v2, as this is the
minimal license requirement for those modles.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
As we're now using SPDX identifiers, on the several
media drivers I wrote, add the proper SPDX, identifying
the license I meant.
As we're now using the short license, it doesn't make sense to
keep the original license text.
Also, fix MODULE_LICENSE to properly identify GPL v2.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Since commit d57ea877af38 ("media: rc: per-protocol repeat period"), most
IR protocols have a lower keyup timeout. This causes problems on the
ite-cir, which has default IR timeout of 200ms.
Since the IR decoders read the trailing space, with a IR timeout of 200ms,
the last keydown will have at least a delay of 200ms. This is more than
the protocol timeout of e.g. rc-6 (which is 164ms). As a result the last
IR will be interpreted as a new keydown event, and we get two keypresses.
Revert the protocol timeout to 250ms, except for cec which needs a timeout
of 550ms.
Fixes: d57ea877af38 ("media: rc: per-protocol repeat period")
Cc: <stable@vger.kernel.org> # 4.14
Reported-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Sean Young <sean@mess.org>
Tested-by: Matthias Reichl <hias@horus.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Several comments are wrongly tagged as kernel-doc, causing
those warnings:
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'irq'
drivers/media/rc/st_rc.c:98: warning: No description found for parameter 'data'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'solo_dev'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'ch'
drivers/media/pci/solo6x10/solo6x10-enc.c:183: warning: No description found for parameter 'qp'
drivers/media/usb/pwc/pwc-dec23.c:652: warning: Cannot understand *
on line 652 - I thought it was a doc line
drivers/media/usb/dvb-usb/cinergyT2-fe.c:40: warning: No description found for parameter 'op'
drivers/media/usb/dvb-usb/friio-fe.c:301: warning: Cannot understand * (reg, val) commad list to initialize this module.
on line 301 - I thought it was a doc line
drivers/media/rc/streamzap.c:201: warning: No description found for parameter 'urb'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'intf'
drivers/media/rc/streamzap.c:333: warning: No description found for parameter 'id'
drivers/media/rc/streamzap.c:464: warning: No description found for parameter 'interface'
drivers/media/i2c/ov5647.c:432: warning: Cannot understand * @short Subdev core operations registration
on line 432 - I thought it was a doc line
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'd'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'addr'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'wlen'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rbuf'
drivers/media/usb/dvb-usb/friio.c:35: warning: No description found for parameter 'rlen'
drivers/media/platform/vim2m.c:350: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/tua6100.c:34: warning: cannot understand function prototype: 'struct tua6100_priv '
drivers/media/platform/sti/hva/hva-h264.c:140: warning: cannot understand function prototype: 'struct hva_h264_stereo_video_sei '
drivers/media/platform/sti/hva/hva-h264.c:150: warning: Cannot understand * @frame_width: width in pixels of the buffer containing the input frame
on line 150 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:356: warning: Cannot understand * @ slice_size: slice size
on line 356 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:369: warning: Cannot understand * @ bitstream_size: bitstream size
on line 369 - I thought it was a doc line
drivers/media/platform/sti/hva/hva-h264.c:395: warning: Cannot understand * @seq_info: sequence information buffer
on line 395 - I thought it was a doc line
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fe'
drivers/media/dvb-frontends/sp887x.c:137: warning: No description found for parameter 'fw'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'n'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'd'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_i'
drivers/media/dvb-frontends/sp887x.c:287: warning: No description found for parameter 'quotient_f'
drivers/media/usb/ttusb-budget/dvb-ttusb-budget.c:83: warning: cannot understand function prototype: 'struct ttusb '
drivers/media/platform/sh_veu.c:277: warning: No description found for parameter 'priv'
drivers/media/dvb-frontends/zl10036.c:33: warning: cannot understand function prototype: 'int zl10036_debug; '
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'state'
drivers/media/dvb-frontends/zl10036.c:179: warning: No description found for parameter 'frequency'
drivers/media/platform/rcar_fdp1.c:1139: warning: No description found for parameter 'priv'
drivers/media/platform/ti-vpe/vpe.c:933: warning: No description found for parameter 'priv'
drivers/media/usb/gspca/ov519.c:36: warning: No description found for parameter 'fmt'
drivers/media/usb/dvb-usb/dib0700_devices.c:3367: warning: No description found for parameter 'adap'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are several parameters there that are named wrong, as
reported by those warnings:
drivers/media/rc/ir-sharp-decoder.c:47: warning: No description found for parameter 'ev'
drivers/media/rc/ir-sharp-decoder.c:47: warning: Excess function parameter 'duration' description in 'ir_sharp_decode'
drivers/media/rc/ir-sanyo-decoder.c:56: warning: No description found for parameter 'ev'
drivers/media/rc/ir-sanyo-decoder.c:56: warning: Excess function parameter 'duration' description in 'ir_sanyo_decode'
drivers/media/rc/ir-xmp-decoder.c:43: warning: No description found for parameter 'ev'
drivers/media/rc/ir-xmp-decoder.c:43: warning: Excess function parameter 'duration' description in 'ir_xmp_decode'
drivers/media/rc/ir-jvc-decoder.c:47: warning: No description found for parameter 'ev'
drivers/media/rc/ir-jvc-decoder.c:47: warning: Excess function parameter 'duration' description in 'ir_jvc_decode'
drivers/media/rc/ir-lirc-codec.c:34: warning: No description found for parameter 'dev'
drivers/media/rc/ir-lirc-codec.c:34: warning: No description found for parameter 'ev'
drivers/media/rc/ir-lirc-codec.c:34: warning: Excess function parameter 'input_dev' description in 'ir_lirc_decode'
drivers/media/rc/ir-lirc-codec.c:34: warning: Excess function parameter 'duration' description in 'ir_lirc_decode'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Signed-off-by: Al Viro <viro@zeniv.linux.org.uk>
|
|
The function documentation here doesn't follow kernel-doc,
as parameters aren't documented. So, stop abusing on
"/**" markups.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Some parameters aren't correctly identified, as noticed by
those warnings:
drivers/media/rc/ir-nec-decoder.c:49: warning: No description found for parameter 'ev'
drivers/media/rc/ir-nec-decoder.c:49: warning: Excess function parameter 'duration' description in 'ir_nec_decode'
drivers/media/rc/ir-nec-decoder.c:189: warning: Excess function parameter 'raw' description in 'ir_nec_scancode_to_raw'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Cleanup those warnings:
drivers/media/rc/rc-ir-raw.c:141: warning: No description found for parameter 'ev'
drivers/media/rc/rc-ir-raw.c:141: warning: Excess function parameter 'type' description in 'ir_raw_event_store_with_filter'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Needed to suppress the following warnings:
drivers/media/rc/img-ir/img-ir-hw.c:351: warning: No description found for parameter 'reg_timings'
drivers/media/rc/img-ir/img-ir-hw.c:351: warning: Excess function parameter 'timings' description in 'img_ir_decoder_convert'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Building the driver with gcc 7.2.1 and:
make ARCH=i386 CF=-D__CHECK_ENDIAN__ CONFIG_DEBUG_SECTION_MISMATCH=y W=1 CHECK='' M=drivers/media
now produces a lot of warnings:
drivers/media/rc/rc-main.c:278: warning: No description found for parameter 'new_keycode'
drivers/media/rc/rc-main.c:278: warning: Excess function parameter 'keycode' description in 'ir_update_mapping'
drivers/media/rc/rc-main.c:387: warning: No description found for parameter 'ke'
drivers/media/rc/rc-main.c:387: warning: No description found for parameter 'old_keycode'
drivers/media/rc/rc-main.c:387: warning: Excess function parameter 'scancode' description in 'ir_setkeycode'
drivers/media/rc/rc-main.c:387: warning: Excess function parameter 'keycode' description in 'ir_setkeycode'
drivers/media/rc/rc-main.c:433: warning: Excess function parameter 'to' description in 'ir_setkeytable'
drivers/media/rc/rc-main.c:506: warning: No description found for parameter 'ke'
drivers/media/rc/rc-main.c:506: warning: Excess function parameter 'scancode' description in 'ir_getkeycode'
drivers/media/rc/rc-main.c:506: warning: Excess function parameter 'keycode' description in 'ir_getkeycode'
drivers/media/rc/rc-main.c:634: warning: No description found for parameter 't'
drivers/media/rc/rc-main.c:634: warning: Excess function parameter 'cookie' description in 'ir_timer_keyup'
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Linux 4.15-rc1
* tag 'v4.15-rc1': (12179 commits)
Linux 4.15-rc1
ARM: BUG if jumping to usermode address in kernel mode
m68k/macboing: Fix missed timer callback assignment
afs: remove redundant assignment of dvnode to itself
afs: cell: Remove unnecessary code in afs_lookup_cell
afs: Fix signal handling in some file ops
afs: Fix some dentry handling in dir ops and missing key_puts
afs: Make afs_write_begin() avoid writing to a page that's being stored
sched/debug: Fix task state recording/printout
x86/decoder: Add new TEST instruction pattern
x86/PCI: Remove unused HyperTransport interrupt support
x86/umip: Fix insn_get_code_seg_params()'s return value
x86/boot/KASLR: Remove unused variable
genirq/matrix: Make - vs ?: Precedence explicit
irqchip/imgpdc: Use resource_size function on resource object
irqchip/qcom: Fix u32 comparison with value less than zero
ipvlan: Fix insufficient skb linear check for ipv6 icmp
ipvlan: Fix insufficient skb linear check for arp
geneve: only configure or fill UDP_ZERO_CSUM6_RX/TX info when CONFIG_IPV6
net: dsa: bcm_sf2: Clear IDDQ_GLOBAL_PWR bit for PHY
...
|
|
ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media
Pull media updates from Mauro Carvalho Chehab:
- Documentation for digital TV (both kAPI and uAPI) are now in sync
with the implementation (except for legacy/deprecated ioctls). This
is a major step, as there were always a gap there
- New sensor driver: imx274
- New cec driver: cec-gpio
- New platform driver for rockship rga and tegra CEC
- New RC driver: tango-ir
- Several cleanups at atomisp driver
- Core improvements for RC, CEC, V4L2 async probing support and DVB
- Lots of drivers cleanup, fixes and improvements.
* tag 'media/v4.15-1' of ssh://gitolite.kernel.org/pub/scm/linux/kernel/git/mchehab/linux-media: (332 commits)
dvb_frontend: don't use-after-free the frontend struct
media: dib0700: fix invalid dvb_detach argument
media: v4l2-ctrls: Don't validate BITMASK twice
media: s5p-mfc: fix lockdep warning
media: dvb-core: always call invoke_release() in fe_free()
media: usb: dvb-usb-v2: dvb_usb_core: remove redundant code in dvb_usb_fe_sleep
media: au0828: make const array addr_list static
media: cx88: make const arrays default_addr_list and pvr2000_addr_list static
media: drxd: make const array fastIncrDecLUT static
media: usb: fix spelling mistake: "synchronuously" -> "synchronously"
media: ddbridge: fix build warnings
media: av7110: avoid 2038 overflow in debug print
media: Don't do DMA on stack for firmware upload in the AS102 driver
media: v4l: async: fix unregister for implicitly registered sub-device notifiers
media: v4l: async: fix return of unitialized variable ret
media: imx274: fix missing return assignment from call to imx274_mode_regs
media: camss-vfe: always initialize reg at vfe_set_xbar_cfg()
media: atomisp: make function calls cleaner
media: atomisp: get rid of storage_class.h
media: atomisp: get rid of wrong stddef.h include
...
|
|
Without this test, sir_ir clumsy claims resources for a device which
does not exist.
The 0-day kernel test robot reports the following errors (in a loop):
sir_ir sir_ir.0: Trapped in interrupt
genirq: Flags mismatch irq 4. 00000000 (ttyS0) vs. 00000000 (sir_ir)
When sir_ir is loaded with the default io and irq, the following happens:
- sir_ir claims irq 4
- user space opens /dev/ttyS0
- in serial8250_do_startup(), some setup is done for ttyS0, which causes
irq 4 to fire (in THRE test)
- sir_ir does not realise it was not for it, and spins until the "trapped
in interrupt"
- now serial driver calls setup_irq() and fails and we get the
"Flags mismatch" error.
There is no port present at 0x3e8 so simply check for the presence of a
port, as suggested by Linus.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Tested-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Sean Young <sean@mess.org>
Cc: <stable@vger.kernel.org> # 4.12+
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.
By default all files without license information are under the default
license of the kernel, which is GPL version 2.
Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.
This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.
How this work was done:
Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,
Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.
The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.
The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.
Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).
All documentation files were explicitly excluded.
The following heuristics were used to determine which SPDX license
identifiers to apply.
- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.
For non */uapi/* files that summary was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139
and resulted in the first patch in this series.
If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:
SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930
and resulted in the second patch in this series.
- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:
SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1
and that resulted in the third patch in this series.
- when the two scanners agreed on the detected license(s), that became
the concluded license(s).
- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.
- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).
- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.
- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.
In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.
Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.
Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.
In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.
Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct
This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.
These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Astrometa T2hybrid (15f4:0135) has IR on Interface 0.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add the keymap module for Astrometa T2hybrid remote control commands.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Evromedia USB Full Hybrid Full HD (1b80:d3b2) has IR on Interface 0.
Remote controller supplied with this tuner fully compatible
with RC_MAP_MSI_DIGIVOX_III.
Signed-off-by: Oleh Kravchenko <oleg@kaa.org.ua>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Maxim Levitsky <maximlevitsky@gmail.com>
Cc: James Hogan <jhogan@kernel.org>
Cc: Hans Verkuil <hans.verkuil@cisco.com>
Cc: "Antti Seppälä" <a.seppala@gmail.com>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: "David Härdeman" <david@hardeman.nu>
Cc: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This is a NEC protocol type remote controller distributed with
96boards poplar@tocoding board.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a NEC protocol type remote controller distributed with
hisilicon TV demo boards.
Signed-off-by: Younian Wang <wangyounian@hisilicon.com>
Signed-off-by: Jiancheng Xue <xuejiancheng@hisilicon.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Mauro Carvalho Chehab <mchehab@kernel.org>
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
It seems that the return value of usb_ifnum_to_if() can be NULL and
needs to be checked.
Signed-off-by: Arvind Yadav <arvind.yadav.cs@gmail.com>
Tested-by: Andrey Konovalov <andreyknvl@google.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
* commit '3728e6a255b5': (904 commits)
Linux 4.14-rc5
x86/microcode: Do the family check first
locking/lockdep: Disable cross-release features for now
x86/mm: Flush more aggressively in lazy TLB mode
mm, swap: use page-cluster as max window of VMA based swap readahead
mm: page_vma_mapped: ensure pmd is loaded with READ_ONCE outside of lock
kmemleak: clear stale pointers from task stacks
fs/binfmt_misc.c: node could be NULL when evicting inode
fs/mpage.c: fix mpage_writepage() for pages with buffers
linux/kernel.h: add/correct kernel-doc notation
tty: fall back to N_NULL if switching to N_TTY fails during hangup
Revert "vmalloc: back off when the current task is killed"
mm/cma.c: take __GFP_NOWARN into account in cma_alloc()
scripts/kallsyms.c: ignore symbol type 'n'
userfaultfd: selftest: exercise -EEXIST only in background transfer
mm: only display online cpus of the numa node
mm: remove unnecessary WARN_ONCE in page_vma_mapped_walk().
mm/mempolicy: fix NUMA_INTERLEAVE_HIT counter
include/linux/of.h: provide of_n_{addr,size}_cells wrappers for !CONFIG_OF
mm/madvise.c: add description for MADV_WIPEONFORK and MADV_KEEPONFORK
...
|
|
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Acked-by: Andi Shyti <andi.shyti@samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The ioctl LIRC_SET_REC_TIMEOUT would set a timeout of 704ns if called
with a timeout of 4294968us.
Cc: <stable@vger.kernel.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The tango HW IR decoder supports NEC, RC-5, RC-6 protocols.
Signed-off-by: Mans Rullgard <mans@mansr.com>
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add a keymap for the Sigma Designs Vantage (dev board) remote control.
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Without device tree, there is no way to use this driver.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
If the kernel is built without device tree, this driver cannot be
used and without gpiolib it cannot control any gpio pin.
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When receiving an nec repeat, rc_repeat() is called and then rc_keydown()
with the last decoded scancode. That last call is redundant.
Fixes: 265a2988d202 ("media: rc-core: consistent use of rc_repeat()")
Cc: <stable@vger.kernel.org> # v4.14
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
There are no users of this functionality (ir-lirc-codec.c has its own
implementation and lirc_zilog.c doesn't use it) so remove it.
This only affects users of the lirc kapi, not rc-core drivers.
Signed-off-by: David Härdeman <david@hardeman.nu>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The 0-day robot reports:
drivers/media/rc/gpio-ir-recv.c: In function 'gpio_ir_recv_irq':
>> drivers/media/rc/gpio-ir-recv.c:38:8: error: implicit declaration of function 'gpiod_get_value' [-Werror=implicit-function-declaration]
Fixes: eed008e605d1 ("[media] media: rc: gpio-ir-recv: use gpiolib API")
For some reason only partial patch was applied. Also include
gpio/consumer.h otherwise compile test fails.
Reported-by: kbuild test robot <fengguang.wu@intel.com>
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Acked-by: Sean Young <sean@mess.org>
|
|
Update my imgtec.com and personal email address to my kernel.org one in
a few places as MIPS will soon no longer be part of Imagination
Technologies, and add mappings in .mailcap so get_maintainer.pl reports
the right address.
Signed-off-by: James Hogan <jhogan@kernel.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Replace the specification of data structures by pointer dereferences
as the parameter for the operator "sizeof" to make the corresponding size
determination a bit safer according to the Linux coding style convention.
This issue was detected by using the Coccinelle software.
Signed-off-by: Markus Elfring <elfring@users.sourceforge.net>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
ir_setkeytable() and ir_create_table() print the same debug message.
Delete the one in ir_setkeytable()
Signed-off-by: Marc Gonzalez <marc_gonzalez@sigmadesigns.com>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The Linus policy on Kconfig is that the default should be no
for all new devices. I.e the user rebuild a new kernel from an
old config should not by default get a larger kernel.
Fixes: b4c184e506a4 ("[media] media: reorganize the main Kconfig items")
Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Acked-by: Geert Uytterhoeven <geert+renesas@glider.be>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Replace self coded binary search, by existing library version.
Signed-off-by: Thomas Meyer <thomas@m3y3r.de>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Gpiolib API is preferred way to access gpios.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
gpio_ir_recv_platform_data are not used anywhere in kernel tree,
so remove it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
There already is standard macro providing driver name, use it.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use of devm_request_irq simplifies error unwinding and as
free_irq was the last user of driver remove function,
remove it too.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Requesting any context irq is not actually great idea since threaded
interrupt handler is run at too unpredictable time which turns
timing information wrong. Fix it by requesting regular interrupt.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use of devm_rc_register_device simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use of devm_gpio_request_one simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use of devm_rc_allocate_device simplifies error unwinding.
Signed-off-by: Ladislav Michl <ladis@linux-mips.org>
Signed-off-by: Sean Young <sean@mess.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
