| Age | Commit message (Collapse) | Author |
|---|
|
Add CI support for DVBSky T980C card. The new host device independent CIMaX SP2 I2C driver was used to implement it.
IRQ handling is not implemented at this point. It could be used to detect the CAM insertion/removal instantly.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If the CI chip has an I2C driver, we need to store I2C client into state.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds basic support for DVBSky T980C card. CI interface is not supported.
DVBSky T980C is a PCIe card with the following components:
- CX23885 PCIe bridge
- Si2168-A20 demodulator
- Si2158-A20 tuner
- CIMaX SP2 CI chip
The demodulator and tuner need firmware. They're the same as used with TT CT2-4650 CI:
https://www.mail-archive.com/linux-media@vger.kernel.org/msg78033.html
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The config structs used for DVBSky T9580 were not initialized. This patch fixes that.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
DVBSky T9580 is a dual tuner card with one DVB-T2/C tuner and one DVB-S2 tuner. It contains the following components:
- PCIe bridge: Conexant CX23885
- Demod for terrestrial/cable: Silicon Labs Si2168-A30
- Tuner for terrestrial/cable: Silicon Labs Si2158-A20
- Demod for sat: Montage DS3103
- Tuner for sat: Montage TS2022
This patch depends on Max Nibble's patch for m88ds3103 (see patchwork 25312: https://patchwork.linuxtv.org/patch/25312/ ).
3 firmwares are needed:
- Si2168-A30 demod and Si2158-A20 tuner: same as TechnoTrend CT2-4400, https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
- Montage DS3103 demod: same as PCTV 461e, Antti has it on his LinuxTV project page: http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
IR receiver is not supported.
Values in cx23885_gpio_setup, cx23885_card_setup and dvbsky_t9580_set_voltage as well as the EEPROM read function are taken from the manufacturer provided semi-open source driver. The drivers in question are Linux GPL'd media tree drivers for cx23885 modified by Max Nibble (nibble.max@gmail.com) with proprietary tuner/demod drivers. Max is aware of this patch and has approved my use of the values in this patch.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Prepare cx23885 driver for handling I2C client that is needed for certain demodulators and tuners (for example Si2168 and Si2157). I2C client for tuner and demod stored in state and unregistering of the I2C devices added into dvb_unregister.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects 417, alsa, core, dvb, vbi and video the
changes are all over.
What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.
Much simpler and more robust. The old code seems to be copied from the
cx88 driver. But it didn't fit the vb2 ops very well and replacing it with
the new scheme made the code easier to understand. Not to mention that this
patch removes 600 lines of code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
drivers/media/pci/cx23885/cx23885-dvb.c:1494:72: warning: Using plain integer as NULL pointer
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
These addresses are usually out-of-date and the top-level license will
always have the right address. So drop it from these sources.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
drivers/media/pci/cx23885/cx23885-dvb.c:768:2: warning: initialized field overwritten [-Woverride-init]
.freq_offset_khz_vhf = 550,
^
drivers/media/pci/cx23885/cx23885-dvb.c:768:2: warning: (near initialization for 'dib7070p_dib0070_config.freq_offset_khz_vhf') [-Woverride-init]
Cc: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
DViCO FusionHDTV DVB-T Dual Express2 is cx23885 + dib7070
[m.chehab@samsung.com: fix conflicts and make checkpatch happy]
Signed-off-by: James Harper <james.harper@ejbdigital.com.au>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Exporting multiple symbols don't work as it causes compilation
breakages, due to the way dvb_attach() works.
This were reported several times, like:
drivers/built-in.o: In function `cxusb_dualdig4_rev2_tuner_attach':
>> cxusb.c:(.text+0x27d4b5): undefined reference to `dib7000p_get_i2c_master'
drivers/built-in.o: In function `dib7070_set_param_override':
cxusb.c:(.text+0x27d5a5): undefined reference to `dib0070_wbd_offset'
>> cxusb.c:(.text+0x27d5be): undefined reference to `dib7000p_set_wbd_ref'
drivers/built-in.o: In function `dib7070_tuner_reset':
>> cxusb.c:(.text+0x27d5f9): undefined reference to `dib7000p_set_gpio'
drivers/built-in.o: In function `cxusb_dualdig4_rev2_frontend_attach':
>> cxusb.c:(.text+0x27df5c): undefined reference to `dib7000p_i2c_enumeration'
In this specific report:
CONFIG_DVB_USB_CXUSB=y
CONFIG_DVB_DIB7000P=m
But the same type of bug can happen if:
CONFIG_DVB_DIB7000P=m
and one of the bridge drivers is compiled builtin (cxusb, cx23885-dvb
and/or dib0700).
As a bonus, dib7000p won't be loaded anymore if the device uses
a different frontend, reducing the memory footprint.
Tested with Hauppauge Nova-TD (2 frontends).
Reported-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Well, what we call as "foo_attach" is the method that should
be called by the dvb_attach() macro.
It should be noticed that the name "dvb_attach" is really a
bad name and don't express what it does.
dvb_attach() basically does three things, if the frontend is
compiled as a module:
- It lookups for the module that it is known to have the
given symbol name and requests such module;
- It increments the module usage (anonymously - so lsmod
doesn't print who loaded the module);
- after loading the module, it runs the function associated
with the dynamic symbol.
When compiled as builtin, it just calls the function given to it.
As dvb_attach() increments refcount, it can't be (easily)
called more than once for the same module, or the kernel
will deny to remove the module, because refcount will never
be zeroed.
In other words, the function name given to dvb_attach()
should be one single symbol that will always be called
before any other function on that module to be used.
For almost all DVB frontends, there's just one function.
However, the dib7000p initialization can require up to 3
functions to be called:
- dib7000p_get_i2c_master;
- dib7000p_i2c_enumeration;
- dib7000p_init (before this patch dib7000_attach).
(plus a bunch of other functions that the bridge driver will
need to call).
As we need to get rid of all those direct calls, because they
cause compilation breakages when bridge is builtin and
frontend is module, we'll need to add a new function that
will be the first one to be called, whatever initialization
is needed.
So, let's rename the function that probes and init the hardware
to dib7000p_init.
A latter patch will add a new dib7000p_attach that will be
used as originally conceived by dvb_attach() way.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
When tuning to 10818V on Astra 28E2, the system tunes to 11343V
instead. This is a regression in the S471 driver introduced with the
changeset: b43ea8068d2090cb1e44632c8a938ab40d2c7419 [media] cx23885:
Fix TeVii S471 regression since introduction of ts2020.
Suggested-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
Signed-off-by: Joakim Hernberg <jhernberg@alchemy.lu>
Tested-by: Mark Clarkstone <hello@markclarkstone.co.uk>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
between multiple instances
...and remove the frontend pointer param from cx24117_attach()
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Those boards were missing the ISDB-T support.
Most of the work on this patch were done by Alfredo.
My work here were to port this patch from Kernel 3.2 to upstream,
fix the issue caused by the set_frontend bad hook, and add the
Kconfig bits.
Tested on a X8502 board rebranded as:
"Leadership - Placa PCI-e de Captura de Vídeo Híbrida" - product code 3800.
Thanks-to: Alfredo Delaiti <alfredodelaiti@netscape.net>
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
When the frontend drivers got converted to DVBv5 API, the original
hook that tracked when a frontend is set got removed, being replaced
by an approach that would use the gate control. That doesn't work
fine with some boards. Also, the code were called more times than
desired.
Replace it by a logic that will hook the dvb set_frontend ops,
with works with both DVBv3 and DVBv5 calls.
Tested on a Mygica X8502 OEM board.
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Patch to make TeVii S471 cards use the ts2020 tuner, since ds3000 driver no
longer contains tuning code.
Signed-off-by: Johannes Koch <johannes@ortsraum.de>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Tuner part of Montage rs2000 chip is similar to ts2020 tuner.
Patch to use ts2020 code.
[mchehab@redhat.com: a few CodingStyle fixes]
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
make the other drivers take use of the separate ts2020 driver
Signed-off-by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
display an error message if either tuner_i2c_addr or demod_i2c_addr
are not specified in the tda10071_config structure
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/pci/cx23885/altera-ci.c:266:5: warning: no previous prototype for 'altera_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:301:5: warning: no previous prototype for 'altera_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:307:5: warning: no previous prototype for 'altera_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:313:5: warning: no previous prototype for 'altera_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:319:5: warning: no previous prototype for 'altera_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:325:5: warning: no previous prototype for 'altera_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:368:5: warning: no previous prototype for 'altera_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:374:5: warning: no previous prototype for 'altera_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:451:5: warning: no previous prototype for 'altera_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:462:6: warning: no previous prototype for 'altera_hw_filt_release' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:584:5: warning: no previous prototype for 'altera_pid_feed_control' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:606:5: warning: no previous prototype for 'altera_ci_start_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:613:5: warning: no previous prototype for 'altera_ci_stop_feed' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:620:5: warning: no previous prototype for 'altera_ci_start_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:625:5: warning: no previous prototype for 'altera_ci_stop_feed_1' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:630:5: warning: no previous prototype for 'altera_ci_start_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:635:5: warning: no previous prototype for 'altera_ci_stop_feed_2' [-Wmissing-prototypes]
drivers/media/pci/cx23885/altera-ci.c:640:5: warning: no previous prototype for 'altera_hw_filt_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:123:5: warning: no previous prototype for 'netup_write_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:150:5: warning: no previous prototype for 'netup_ci_get_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:169:5: warning: no previous prototype for 'netup_ci_op_cam' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:239:5: warning: no previous prototype for 'netup_ci_read_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:245:5: warning: no previous prototype for 'netup_ci_write_attribute_mem' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:251:5: warning: no previous prototype for 'netup_ci_read_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:257:5: warning: no previous prototype for 'netup_ci_write_cam_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:263:5: warning: no previous prototype for 'netup_ci_slot_reset' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:292:5: warning: no previous prototype for 'netup_ci_slot_shutdown' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:298:5: warning: no previous prototype for 'netup_ci_set_irq' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:319:5: warning: no previous prototype for 'netup_ci_slot_ts_ctl' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:375:5: warning: no previous prototype for 'netup_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:402:5: warning: no previous prototype for 'netup_poll_ci_slot_status' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:415:5: warning: no previous prototype for 'netup_ci_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:520:6: warning: no previous prototype for 'netup_ci_exit' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cimax2.c:90:5: warning: no previous prototype for 'netup_read_i2c' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-av.c:26:6: warning: no previous prototype for 'cx23885_av_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-cards.c:1430:5: warning: no previous prototype for 'netup_jtag_io' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-core.c:306:6: warning: no previous prototype for 'cx23885_irq_add' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-dvb.c:662:5: warning: no previous prototype for 'netup_altera_fpga_rw' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-f300.c:150:5: warning: no previous prototype for 'f300_set_voltage' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:249:5: warning: no previous prototype for 'cx23885_input_init' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:353:6: warning: no previous prototype for 'cx23885_input_fini' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-input.c:76:6: warning: no previous prototype for 'cx23885_input_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:134:5: warning: no previous prototype for 'cx23885_g_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:185:5: warning: no previous prototype for 'cx23885_s_register' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ioctl.c:27:5: warning: no previous prototype for 'cx23885_g_chip_ident' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:101:6: warning: no previous prototype for 'cx23885_ir_tx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:37:6: warning: no previous prototype for 'cx23885_ir_rx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:60:6: warning: no previous prototype for 'cx23885_ir_tx_work_handler' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23885-ir.c:76:6: warning: no previous prototype for 'cx23885_ir_rx_v4l2_dev_notify' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1203:5: warning: no previous prototype for 'cx23888_ir_probe' [-Wmissing-prototypes]
drivers/media/pci/cx23885/cx23888-ir.c:1253:5: warning: no previous prototype for 'cx23888_ir_remove' [-Wmissing-prototypes]
drivers/media/pci/cx23885/netup-init.c:109:6: warning: no previous prototype for 'netup_initialize' [-Wmissing-prototypes]
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The device is based on STV0903 demodulator, STB6100 tuner
and CX23885 chipset; subsystem id: 8000:3034
This is a modified version of the official Prof Tuners Group patch:
http://www.proftuners.com/sites/default/files/prof8000_0.patch
[mchehab@redhat.com: trivial merge conflict fixup]
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
