| Age | Commit message (Collapse) | Author |
|---|
|
Add support for these two new cards.
Based upon Devin's initial patch made for an older kernel which I
cleaned up and rebased. Thanks to Kernel Labs for that work.
Signed-off-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Change ts2022 driver to ts2020 driver. ts2020 driver supports
both chip models.
Cc: Olli Salonen <olli.salonen@iki.fi>
Cc: Nibble Max <nibble.max@gmail.com>
Tested-by: David Howells <dhowells@redhat.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add board profile for Hauppauge WinTV-HVR5525.
Device is build upon following main components:
Conexant CX23888
Montage M88RS6000
Allegro A8293
Silicon Labs Si2168-B40
Silicon Labs Si2157-A30
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
DVBSky T9580 is a dual tuner card with one DVB-T2/C tuner and one DVB-S2 tuner. It contains the following components:
- PCIe bridge: Conexant CX23885
- Demod for terrestrial/cable: Silicon Labs Si2168-A30
- Tuner for terrestrial/cable: Silicon Labs Si2158-A20
- Demod for sat: Montage DS3103
- Tuner for sat: Montage TS2022
This patch depends on Max Nibble's patch for m88ds3103 (see patchwork 25312: https://patchwork.linuxtv.org/patch/25312/ ).
3 firmwares are needed:
- Si2168-A30 demod and Si2158-A20 tuner: same as TechnoTrend CT2-4400, https://www.mail-archive.com/linux-media@vger.kernel.org/msg76944.html
- Montage DS3103 demod: same as PCTV 461e, Antti has it on his LinuxTV project page: http://palosaari.fi/linux/v4l-dvb/firmware/M88DS3103/
IR receiver is not supported.
Values in cx23885_gpio_setup, cx23885_card_setup and dvbsky_t9580_set_voltage as well as the EEPROM read function are taken from the manufacturer provided semi-open source driver. The drivers in question are Linux GPL'd media tree drivers for cx23885 modified by Max Nibble (nibble.max@gmail.com) with proprietary tuner/demod drivers. Max is aware of this patch and has approved my use of the values in this patch.
Signed-off-by: Olli Salonen <olli.salonen@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
It's just as easy to do it in the driver. This dependency only uses a
fraction of the btcx-risc module and doing it directly in the driver
adds only a few lines. The btcx-risc module is really meant for the
bttv driver, not for other drivers.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
As usual, this patch is very large due to the fact that half a vb2 conversion
isn't possible. And since this affects 417, alsa, core, dvb, vbi and video the
changes are all over.
What made this more difficult was the peculiar way the risc program was setup.
The driver allowed for running out of buffers in which case the DMA would stop
and restart when the next buffer was queued. There was also a complicated
timeout system for when buffers weren't filled. This was replaced by a much
simpler scheme where there is always one buffer around and the DMA will just
cycle that buffer until a new buffer is queued. In that case the previous
buffer will be chained to the new buffer. An interrupt is generated at the
start of the new buffer telling the driver that the previous buffer can be
passed on to userspace.
Much simpler and more robust. The old code seems to be copied from the
cx88 driver. But it didn't fit the vb2 ops very well and replacing it with
the new scheme made the code easier to understand. Not to mention that this
patch removes 600 lines of code.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
The same card entry is used for HVR-4400 and HVR-5500.
Only HVR-5500 has been tested.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Due to DViCO FusionHDTV DVB-T Dual Express2, we also need to
autoselect this tuner.
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Signed-off-by: Luis Alves <ljalvs@gmail.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
Those boards were missing the ISDB-T support.
Most of the work on this patch were done by Alfredo.
My work here were to port this patch from Kernel 3.2 to upstream,
fix the issue caused by the set_frontend bad hook, and add the
Kconfig bits.
Tested on a X8502 board rebranded as:
"Leadership - Placa PCI-e de Captura de Vídeo Híbrida" - product code 3800.
Thanks-to: Alfredo Delaiti <alfredodelaiti@netscape.net>
Tested-by: Alfredo Delaiti <alfredodelaiti@netscape.net>
Signed-off-by: Mauro Carvalho Chehab <m.chehab@samsung.com>
|
|
make the other drivers take use of the separate ts2020 driver
Signed-off-by: Konstantin Dimitrov <kosio.dimitrov@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add basic DVB-S2 support for the Hauppauge HVR-4400 PCIe board.
Thanks to Antti Palosaari and Devin Heitmueller for their
suggestions and testing.
Signed-off-by: Michael Krufky <mkrufky@linuxtv.org>
Reviewed-by: Devin Heitmueller <dheitmueller@kernellabs.com>
Reviewed-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The Terratec Cinergy T PCIe Dual is based on the CX23885, and uses
MT2063, DRX-3913k and DRX-3916k chips, so select the relevant drivers.
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The device is based on STV0903 demodulator, STB6100 tuner
and CX23885 chipset; subsystem id: 8000:3034
This is a modified version of the official Prof Tuners Group patch:
http://www.proftuners.com/sites/default/files/prof8000_0.patch
[mchehab@redhat.com: trivial merge conflict fixup]
Signed-off-by: Mariusz Bialonczyk <manio@skyboo.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Instead of having 3 options to allow customizing the media
sub-drivers (tuners, I2C drivers, frontends), merge all of
them into just one.
That simplifies the life for users, as they can just keep
this untouched.
Life for developers is also simpler, as there's now just
one Kconfig item to remember, for the ancillary sub-drivers
providing supports for chips that could change from one
board design to another.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Rename all PCI drivers with their own directory under
drivers/media/video into drivers/media/pci and update the
building system.
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
