| Age | Commit message (Collapse) | Author |
|---|
|
SPA location LSB register is at 0x70.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
We need to import the changes at media.h, as we have a
followup patch that depends on it.
* v4l_for_linus:
[media] media.h: use hex values for range offsets, move connectors base up.
[media] adv7604: fix tx 5v detect regression
|
|
smatch complains about non-ascii characters. It turns out that a wide-dash character
was used instead of the more common '-' character.
Replace those dashes with -.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
drivers/media/i2c/tvp5150.c:1394 tvp5150_parse_dt() warn: buffer overflow 'decoder->input_ent' 3 <= 3
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The V4L2_CID_TX_EDID_PRESENT control reports if an EDID is present.
The adv7511 however still reported the EDID present after disconnecting
the HDMI cable. Fix the logic regarding this control. And when the EDID
is disconnected also call ADV7511_EDID_DETECT to notify the bridge driver.
This was also missing.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.12 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The 5 volt detect functionality broke in 3.14: the code reads IO register 0x70
again after it has already been cleared. Instead it should use the cached
irq_reg_0x70 value and the io_write to 0x71 to clear 0x70 can be dropped since
this has already been done.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Cc: <stable@vger.kernel.org> # for v3.14 and up
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Some macros were changed/removed at the material for v4.5. We need
to sync with those changes here, in order to avoid troubles.
* v4l_for_linus:
[media] media.h: get rid of MEDIA_ENT_F_CONN_TEST
[media] [for,v4.5] media.h: increase the spacing between function ranges
[media] media: i2c/adp1653: probe: fix erroneous return value
[media] media: davinci_vpfe: fix missing unlock on error in vpfe_prepare_pipeline()
|
|
MEDIA_ENT_F_CONN_TEST is not really a connector, it is actually
a signal generator. Also, as other drivers use the
V4L2_CID_TEST_PATTERN control for signal generators, let's change
the driver accordingly.
Tested with Terratec Grabster AV350.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The tvp5150 decoder has different input connectors. The actual list of
HW inputs depends on the device version but all have at least these 3:
1) Composite0
2) Composite1
3) S-Video
and some variants have a 4th possible input connector:
4) Signal generator
The driver currently uses the .s_routing callback to switch the input
connector but since these are separate HW blocks, it's better to use
media entities to represent the input connectors and their source pads
linked with the decoder's sink pad.
This allows user-space to use the MEDIA_IOC_SETUP_LINK ioctl to choose
the input connector. For example using the media-ctl user-space tool:
$ media-ctl -r -l '"Composite0":0->"tvp5150 1-005c":0[1]'
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add a header file for the tvp5150 input connectors constants that
can be shared between the driver and Device Tree source files.
[mchehab@osg.samsung.com: rename tvp5150.h also at em28xx-cards.c]
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Not all tvp5150 variants support the same, for example some have an
internal signal generator that can output a black screen.
So the device id and rom version have to be stored in the driver's
state to know what variant is a given device.
While being there, remove some redundant comments about the device
version since there is already calls to v4l2_info() with that info.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
If the parallel mbus configuration is not correct, the endpoint
device node isn't currently put again in the error path. Fix it.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This transmitter now supports configuring the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This receiver now supports reading the IT content type of the incoming
video.
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Use the helper to enumerate and set DV timings instead of a custom code.
This will ease debugging too, as it is consistent with other drivers.
Signed-off-by: Jean-Michel Hautbois <jean-michel.hautbois@veo-labs.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Auto-gain and auto-exposure clusters in the ov9650 driver have both a
size of 2, not 3 controls. Fix this.
Signed-off-by: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The adp1653_probe() function may return positive value EINVAL
which is obviously wrong.
Signed-off-by: Anton Protopopov <a.s.protopopov@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Linux 4.5-rc3
* tag 'v4.5-rc3': (644 commits)
Linux 4.5-rc3
epoll: restrict EPOLLEXCLUSIVE to POLLIN and POLLOUT
radix-tree: fix oops after radix_tree_iter_retry
MAINTAINERS: trim the file triggers for ABI/API
dax: dirty inode only if required
thp: make deferred_split_scan() work again
mm: replace vma_lock_anon_vma with anon_vma_lock_read/write
ocfs2/dlm: clear refmap bit of recovery lock while doing local recovery cleanup
um: asm/page.h: remove the pte_high member from struct pte_t
mm, hugetlb: don't require CMA for runtime gigantic pages
mm/hugetlb: fix gigantic page initialization/allocation
mm: downgrade VM_BUG in isolate_lru_page() to warning
mempolicy: do not try to queue pages from !vma_migratable()
mm, vmstat: fix wrong WQ sleep when memory reclaim doesn't make any progress
vmstat: make vmstat_update deferrable
mm, vmstat: make quiet_vmstat lighter
mm/Kconfig: correct description of DEFERRED_STRUCT_PAGE_INIT
memblock: don't mark memblock_phys_mem_size() as __init
dump_stack: avoid potential deadlocks
mm: validate_mm browse_rb SMP race condition
...
|
|
A recent patch broke the msp3400 driver when CONFIG_MEDIA_CONTROLLER
is not set:
drivers/media/i2c/msp3400-driver.h:107:5: error: "CONFIG_MEDIA_CONTROLLER" is not defined [-Werror=undef]
It was clearly a typo, and this patch changes the
"#if CONFIG_MEDIA_CONTROLLER" to a working IS_ENABLED() check.
Fixes: fb4932821731 ("[media] msp3400: initialize MC data")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This is a partial revert of commit ed8d1cf07cb16d ("[media] Export I2C
module alias information in missing drivers") that exported the module
aliases for the I2C drivers that were missing to make autoload to work.
But there is a bug report [0] that auto load of the ir-kbd-i2c driver
cause the Hauppauge HD-PVR driver to not behave correctly.
This is a hdpvr latent bug that was just exposed by ir-kbd-i2c module
autoloading working and will also happen if the I2C driver is built-in
or a user calls modprobe to load the module and register the driver.
But there is a regression experimented by users so until the real bug
is fixed, let's not export the module alias for the ir-kbd-i2c driver
even when this just masks the actual issue.
[0]: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=810726
Fixes: ed8d1cf07cb1 ("[media] Export I2C module alias information in missing drivers")
Cc: <stable@vger.kernel.org> # 4.3+
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
Clang complains about an extraneous definition of the module
device table after the patch to add it was accidentally merged
twice:
../drivers/media/i2c/s5c73m3/s5c73m3-spi.c:40:1: error: redefinition of
'__mod_of__s5c73m3_spi_ids_device_table'
MODULE_DEVICE_TABLE(of, s5c73m3_spi_ids);
^
../include/linux/module.h:223:27: note: expanded from macro 'MODULE_DEVICE_TABLE'
extern const typeof(name) __mod_##type##__##name##_device_table \
^
<scratch space>:99:1: note: expanded from here
__mod_of__s5c73m3_spi_ids_device_table
This removes the second definition.
Fixes: f934a94bb566 ("[media] s5c73m3: Export OF module alias information")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The v4l2_of_parse_endpoint() function can fail so check the return value.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The rcar_vin driver relies on this.
Signed-off-by: Ulrich Hecht <ulrich.hecht+renesas@gmail.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
i2c_wr() is called from ops and the interrupt service routine, while
state->wr_data is shared and unprotected, and could be overwritten.
This shared buffer is therefore replaced with a local array with fixed
size. The array has the size of one EDID block (128 bytes) + 2 bytes
i2c address, and the EDID is written block by block (up to 8 blocks).
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The intent was to return -1 on error and that's what the callers expect
but the current code returns USHRT_MAX instead.
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Prevent unnecessary kernel log spamming.
Signed-off-by: Mats Randgaard <matrandg@cisco.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Create a source pad and set the media controller type to the sensor.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The saa7115 driver is used on several em28xx-based devices.
Now that we're about to add MC support to em28xx, we need to
be sure that the saa711x demod will be properly mapped at MC.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The tvp5150 is an analog TV decoder. Identify as such at
the media graph, or otherwise devices using it would fail.
That avoids the following warning:
[ 1546.669139] usb 2-3.3: Entity type for entity tvp5150 5-005c was not initialized!
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add pads and set the device type when used with the media
controller.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The tvp5150 doesn't have just one pad. It has 3 ones:
- IF input
- Video output
- VBI output
Fix it and use the macros for the pad indexes.
Reviewed-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch enables the tvp5150 decoder driver to be used with the media
controller framework by adding pad-level subdev operations and init the
media entity pad.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
The tvp5150 output video is interlaced so mark the format
field as alternate and reduce the height to the half.
[javier: split patch and write commit message]
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
|
|
This patch were a workaround for a regression at tvp5150, but
it causes troubles on devices with omap3+tvp5151 when working
in non-parallel bus mode.
Now that em28xx was fixed, we can get rid of that.
This reverts commit 47de9bf8931e6bf9c92fdba9867925d1ce482ab1.
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The ov2659 driver performs device detection and initialization in the
following way:
- send reset command REG_SOFTWARE_RESET
- load array of predefined register's setting (~150 values)
- read device version REG_SC_CHIP_ID_H/REG_SC_CHIP_ID_L
- check version and exit if invalid.
As result, for not connected device there will be >~150 i2c transactions
executed before device version checking and exit (there are no
failures detected because ov2659 declared as I2C_CLIENT_SCCB and NACKs
are ignored in this case).
Let's fix that by checking the chip version first and start
initialization only if it's supported.
Cc: Benoit Parrot <bparrot@ti.com>
Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Add optional reset and standby gpios. The reset gpio is used to reset
the chip in power_on().
The standby gpio is not used currently. It is just unset, so the chip is
not in standby.
Signed-off-by: Markus Pargmann <mpa@pengutronix.de>
Reviewed-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
changeset 460b6c0831cb ("tvp5150: Add s_stream subdev operation
support") broke for em28xx-based devices with uses tvp5150. On those
devices, touching the TVP5150_MISC_CTL register causes em28xx to stop
streaming.
I suspect that it uses the 27 MHz clock provided by tvp5150 to feed
em28xx. So, change the logic to do nothing on s_stream if the tvp5150 is
not set up to work with V4L2_MBUS_PARALLEL.
Tested with Hauppauge WinTV USB 2 model 42012 Rev. C186
(USB ID: 2040:4200).
Cc: Javier Martinez Canillas <javier@osg.samsung.com>
Cc: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The Documentation/devicetree/bindings/media/i2c/tvp5150.txt DT binding doc
lists "ti,tvp5150" as the device compatible string but the driver does not
have an OF match table. Add the table to the driver so the I2C core can do
an OF style match.
Signed-off-by: Eduard Gavin <egavinc@gmail.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
The video decoder supports either 8-bit 4:2:2 YUV with discrete syncs
or 8-bit ITU-R BT.656 with embedded syncs output format but currently
BT.656 it's always reported. Allow to configure the format to use via
either platform data or a device tree definition.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
After power-up, the tvp5150 decoder is in a unknown state until the
RESETB pin is driven LOW which reset all the registers and restarts
the chip's internal state machine.
The init sequence has some timing constraints and the RESETB signal
can only be used if the PDN (Power-down) pin is first released.
So, the initialization sequence is as follows:
1- PDN (active-low) is driven HIGH so the chip is power-up
2- A 20 ms delay is needed before sending a RESETB (active-low) signal.
3- The RESETB pulse duration is 500 ns.
4- A 200 us delay is needed for the I2C client to be active after reset.
This patch used as a reference the logic in the IGEPv2 board file from
the ISEE 2.6.37 vendor tree.
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds the .g_mbus_config subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds the .s_stream subdev operation to the driver.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
This patch adds support for the V4L2_CID_PIXEL_RATE control.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Expand the version detection code to identity the tvp5151.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Move the version detection code to a separate function and restructure
it to prepare for TVP5151 support.
Signed-off-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
