| Age | Commit message (Collapse) | Author |
|---|
|
Parse async sub-devices related to the sensor by switching the async
sub-device registration function.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hans.verkuil@cisco.com>
Reviewed-by: Sebastian Reichel <sebastian.reichel@collabora.co.uk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Previously, the sensor was not streaming after resume from suspend,
i.e. on S0->S3->S0 transition. Due to this, camera app preview appeared
as stuck.
Now, handle streaming state correctly in case of suspend-resume.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Previously, images were relatively darker due to non-optimal
settings for black target level and bias.
Now, use recommended settings for black target level and output bias
as default values. The same default settings apply to all the resolutions.
Given these recommeneded settings do not change dynamically, add these to
existing mode register settings.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@osg.samsung.com>
|
|
Previously, vblank range given to user was too big, falling outside
of permissible range for a given resolution. Sometimes, too low vblank
resulted in errors.
Now, limit vblank to only permissible range for a given resolution.
This change limits lower-bounds of vblank, doesn't affect upper bounds.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Previously, pixel-rate/(pixels-per-line * lines-per-frame) was
yielding incorrect frame timing for the user.
OV sensor is using internal timing and this requires
conversion (internal timing -> PPL) for correct HBLANK calculation.
Now, change pixels-per-line domain from internal sensor clock to
pixels domain. Set HBLANK read-only because fixed PPL is used for all
resolutions. And, use more accurate link-frequency 422.4MHz instead of
rounding down to 420MHz.
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
drivers/media/i2c/ov5670.c:2033:2-3: Unneeded semicolon
Remove unneeded semicolon.
Generated by: scripts/coccinelle/misc/semicolon.cocci
CC: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Fengguang Wu <fengguang.wu@intel.com>
Signed-off-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Provides single source pad with up to 2592x1944 pixels at 10-bit raw
bayer format over MIPI CSI2 two lanes at 840Mbps/lane.
The driver supports following features:
- up to 30fps at 5M pixels
- manual exposure
- digital/analog gain
- V-blank/H-blank
- test pattern
- media controller
- runtime pm
[mchehab@s-opensource.com: fix a trivial merge conflict at Makefile]
Signed-off-by: Chiranjeevi Rapolu <chiranjeevi.rapolu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
