| Age | Commit message (Collapse) | Author |
|---|
|
The OV8865 is a 8 Mpx CMOS image sensor producing 3264x2448 at 30 fps.
Other modes (including some with sub-sampling) are available too.
It outputs 10-bit bayer CFA data through a MIPI CSI-2 interface with
up to 4 lanes supported.
Some register initialisation sequences are still needed for this driver,
as they cover registers for which no documentation is available.
This work is based on the first version of the driver submitted by
Kévin L'hôpital, which was adapted to mainline from the Allwinner BSP.
This version is a rewrite of the first version that matches the structure
of the OV5648 driver, with explicit PLL configuration, all the necessary
mode-specific fields, associatied registers and reduced static sequences.
It was tested with the Banana Pi Camera Board v3 and the Banana Pi M3.
Co-developed-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Kévin L'hôpital <kevin.lhopital@bootlin.com>
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The OV5648 is a 5 Mpx CMOS image sensor, connected via MIPI CSI-2
in a one or two lane configuration.
Most of the features of the hardware are supported, including:
- Auto and manual exposition/gain
- Auto and manual white balance
- Horizontal and vertical flip
- Test patterns
But the following are still missing:
- Debanding, based on power source frequency;
- Exposition setting correlated to time units.
Signed-off-by: Paul Kocialkowski <paul.kocialkowski@bootlin.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
MIPI CCS replaces SMIA and SMIA++ as the current standard. CCS brings new
features while existing functionality will be supported. Rename the
smiapp-pll as ccs-pll accordingly.
Also add Intel copyright to the files.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a V4L2 sub-device driver for OmniVision OV02A10 image sensor.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Rename the "smiapp" driver as "ccs". MIPI CCS is the contemporary standard
for raw Bayer camera sensors. The driver retains support for the SMIA++
and SMIA compliant camera sensors. A module alias is added for old user
space using "smiapp" module name.
Add Intel copyright while at it.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a v4l2 sub-device driver for the OminiVision ov9734 image sensor
which can deliver maximum 720p image frames at 30 fps. This driver
also add vertical blanking, exposure, test pattern, digital and analog
gain control for the image sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Tianshu Qiu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Fix OV2740 build breakage by selecting REGMAP_I2C config:
ov2740.c:1011:23: error: variable has incomplete type 'struct regmap_config'
struct regmap_config regmap_config = { };
^
ov2740.c:1011:9: note: forward declaration of 'struct regmap_config'
struct regmap_config regmap_config = { };
^
ov2740.c:1028:11: error: implicit declaration of function 'devm_regmap_init_i2c'
regmap = devm_regmap_init_i2c(client, ®map_config);
Signed-off-by: Sergey Senozhatsky <sergey.senozhatsky@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Linux 5.9-rc4
* tag 'v5.9-rc4': (1001 commits)
Linux 5.9-rc4
io_uring: fix linked deferred ->files cancellation
io_uring: fix cancel of deferred reqs with ->files
include/linux/log2.h: add missing () around n in roundup_pow_of_two()
mm/khugepaged.c: fix khugepaged's request size in collapse_file
mm/hugetlb: fix a race between hugetlb sysctl handlers
mm/hugetlb: try preferred node first when alloc gigantic page from cma
mm/migrate: preserve soft dirty in remove_migration_pte()
mm/migrate: remove unnecessary is_zone_device_page() check
mm/rmap: fixup copying of soft dirty and uffd ptes
mm/migrate: fixup setting UFFD_WP flag
mm: madvise: fix vma user-after-free
checkpatch: fix the usage of capture group ( ... )
fork: adjust sysctl_max_threads definition to match prototype
ipc: adjust proc_ipc_sem_dointvec definition to match prototype
mm: track page table modifications in __apply_to_page_range()
MAINTAINERS: IA64: mark Status as Odd Fixes only
MAINTAINERS: add LLVM maintainers
MAINTAINERS: update Cavium/Marvell entries
mm: slub: fix conversion of freelist_corrupted()
...
|
|
Make use of SCCB APIs for regmap operations.
Remove i2c_check_functionality as devm_regmap_init_sccb
does it for us.
Signed-off-by: Raag Jadav <raagjadav@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The driver expects struct gpio_chip has of_node field and that field is
only there if CONFIG_OF_GPIO is defined. Fix this by changing the OF
dependency to OF_GPIO.
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
After the recent conversion of the media build infrastructure to select
V4L2 components instead of depending on their presence, which took place
in:
32a363d0b0b14 ("media: Kconfig files: use select for V4L2 subdevs and MC")
imx214 stands out as being the (only?) media I2C driver that still depends
on a V4L2 core symbol instead of selecting it.
This confuses the build system which claims it has detected a circular
dependency when other drivers select the same symbol as the imx214
driver does.
drivers/media/i2c/Kconfig:728:error: recursive dependency detected!
drivers/media/i2c/Kconfig:728: symbol VIDEO_IMX214 depends on V4L2_FWNODE
drivers/media/v4l2-core/Kconfig:71: symbol V4L2_FWNODE is selected by VIDEO_BCM2835_UNICAM
drivers/media/platform/bcm2835/Kconfig:3: symbol VIDEO_BCM2835_UNICAM depends on VIDEO_V4L2_SUBDEV_API
drivers/media/v4l2-core/Kconfig:19: symbol VIDEO_V4L2_SUBDEV_API depends on MEDIA_CONTROLLER
drivers/media/Kconfig:168: symbol MEDIA_CONTROLLER is selected by VIDEO_IMX214
Fix this by making the imx214 driver select V4L2_FWNODE instead of
depending on it and align it with all the other drivers.
Fixes: 32a363d0b0b14 ("media: Kconfig files: use select for V4L2 subdevs and MC")
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The RDACM20 is a GMSL camera supporting 1280x800 resolution images
developed by IMI based on an Omnivision 10635 sensor and a Maxim MAX9271
GMSL serializer.
The GMSL link carries power, control (I2C) and video data over a
single coax cable.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Reviewed-by: Rob Herring <robh@kernel.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
The MAX9286 is a 4-channel GMSL deserializer with coax or STP input and
CSI-2 output. The device supports multicamera streaming applications,
and features the ability to synchronise the attached cameras.
CSI-2 output can be configured with 1 to 4 lanes, and a control channel
is supported over I2C, which implements an I2C mux to facilitate
communications with connected cameras across the reverse control
channel.
Signed-off-by: Jacopo Mondi <jacopo+renesas@jmondi.org>
Signed-off-by: Kieran Bingham <kieran.bingham+renesas@ideasonboard.com>
Signed-off-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Add a V4L2 sub-device driver for DW9768 voice coil motor,
providing control to set the desired focus via IIC serial interface.
Signed-off-by: Dongchun Zhu <dongchun.zhu@mediatek.com>
Reviewed-by: Tomasz Figa <tfiga@chromium.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
As the ACPI id of ov2740 camera sensor was registered as "INT3474",
current ov2740 driver is supposed to be working with ACPI only.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Suggested-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
OminiVision ov2740 is a 2 megapixels RAW RGB image sensor which can
deliver 1920x1080@60fps frames. This driver add the support of
vertical blanking, exposure, test pattern, digital and analog gain
control for sensor.
Signed-off-by: Bingbu Cao <bingbu.cao@intel.com>
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Qiu, Tianshu <tian.shu.qiu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are *lots* of I2C ancillary drivers. While we're using
comments to group them, all options appear at the same menu.
It should be a lot clearer to group them into sub-menus, with
may help people to go directly to the driver(s) he's needing
to enable.
Suggested-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Right now, there are I2C drivers that don't depend on
camera support before and after those.
Move the camera support drivers to the end, and add
a notice at the "endif", in order to make easier to
maintain and to avoid adding extra dependencies at
the other i2c/*/Kconfig files.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
There are lots of drivers that only work when the media controller
and/or the V4L2 subdev APIs are present.
Right now, someone need to first enable those APIs before
using those drivers.
Well, ideally, drivers, should, instead *optionally*
depend on it, in order for PC camera drivers to be able to use
them, but nowadays most drivers are UVC cameras, with don't
require a sensor driver.
So, be it.
Let's instead make them select the MEDIA_CONTROLLER and the
SUBDEV API, in order to make easier for people to be able
of enabling them.
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
While upgrading from 5.5.2 -> 5.5.6 I was surprised by:
ld: drivers/media/i2c/tvp5150.o: in function `tvp5150_probe':
tvp5150.c:(.text+0x11ac): undefined reference to
`__devm_regmap_init_i2c'
make: *** [Makefile:1078: vmlinux] Error 1
The fix was quick enough, make VIDEO_TVP5150 select REGMAP_I2C
And a quick grep showed that it was needed by more targets.
Signed-off-by: Ian Kumlien <ian.kumlien@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>
|
|
Adds a driver for the 8MPix Sony IMX219 CSI2 sensor.
Whilst the sensor supports 2 or 4 CSI2 data lanes, this driver
currently only supports 2 lanes.
8MPix @ 15fps, 1080P @ 30fps (cropped FOV), and 1640x1232 (2x2 binned)
@ 30fps are currently supported.
[Sakari Ailus: make imx219_check_hwcfg static]
Signed-off-by: Dave Stevenson <dave.stevenson@raspberrypi.com>
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a V4L2 sub-device driver for Hynix Hi-556 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[sakari.ailus@linux.intel.com: Remove MEDIA_CAMERA_SUPPORT from Kconfig dependencies]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>
|
|
Add driver for Sony IMX290 CMOS image sensor driver. The driver only
supports I2C interface for programming and MIPI CSI-2 for sensor output.
[Sakari Ailus: Rewrapped a few lines over 80 chars a little.]
Signed-off-by: Manivannan Sadhasivam <manivannan.sadhasivam@linaro.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If VIDEO_OV5695 is y and V4L2_FWNODE is m, building fails:
drivers/media/i2c/ov5695.o: In function `ov5695_probe':
ov5695.c:(.text+0xf4c): undefined reference to `v4l2_async_register_subdev_sensor_common'
Select V4L2_FWNODE like OV5675 does.
Fixes: 623df5d710fe ("media: i2c: ov5695: Modify the function of async register subdev related devices")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch adds support for a programmable enable pin. It can be used in
situations where the ANA-vcc is not configurable (dummy-regulator), or
just to have a more fine control of the power saving.
The use of the enable pin is optional.
Signed-off-by: Ricardo Ribalda Delgado <ribalda@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
On some board it is possible that the sensor 'powerdown' and or 'reset'
pin might be controlled by gpio instead of being tied.
To implement we add pm_runtime support which will handle the power
up/down sequence when it is available otherwise the sensor will be
powered on at module insertion/probe and powered off at module removal.
Now originally the driver assumed that the sensor would always stay
powered and keep its register setting. We cannot assume this anymore, so
every time we "power up" we need to re-program the initial registers
configuration first. This was previously done only at probe time.
[Sakari Ailus: Resolve a conflict in Kconfig]
Signed-off-by: Benoit Parrot <bparrot@ti.com>
Acked-by: Lad, Prabhakar <prabhakar.csengg@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Instead of individually depending on MEDIA_CAMERA_SUPPORT (or forgetting
it), put all camera sensor, lens and flash drivers under
MEDIA_CAMERA_SUPPORT as a whole. The lens VCM devices didn't use to do
this, but make them depend on MEDIA_CAMERA_SUPPORT as well since there's
no use for these devices without that in practice.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
If CONFIG_REGMAP_I2C is not set, building fails:
drivers/media/i2c/max2175.o: In function `max2175_probe':
max2175.c:(.text+0x1404): undefined reference to `__devm_regmap_init_i2c'
Select REGMAP_I2C to fix this.
Reported-by: Hulk Robot <hulkci@huawei.com>
Fixes: b47b79d8a231 ("[media] media: i2c: max2175: Add MAX2175 support")
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Some users have been having a hard time finding the hidden
menus. A typically case are camera sensor drivers
(e.g IMX219, OV5645, etc), which are common on embedded
platforms and not really "ancillary" devices.
The problem with MEDIA_SUBDRV_AUTOSELECT seems to be related
to the fact that it uses the "visible" syntax to hide
the menus.
This is not obvious and it normally takes some time to
figure out.
To fix the problem, add a comment on each of hidden menus,
which should clarify what option is causing menus to be hidden.
Signed-off-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add a V4L2 sub-device driver for Omnivision ov5675 image sensor.
This is a camera sensor using the I2C bus for control and the
CSI-2 bus for data.
This driver supports following features:
- manual exposure and analog/digital gain control support
- vblank/hblank control support
- test pattern support
- media controller support
- runtime PM support
- support following resolutions:
+ 2592x1944 at 30FPS
+ 1296x972 at 30FPS
[Sakari Ailus: Wrapped a few long lines.]
[mchehab+samsung@kernel.org: fix a checkpatch warning]
Signed-off-by: Shawn Tu <shawnx.tu@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
CONFIG_DRM_I2C_ADV7511 and CONFIG_VIDEO_ADV7511 bind to the same
platform device, so whichever driver gets loaded first will be used on
the device. So they shouldn't be enabled at the same time.
Rework so that VIDEO_ADV7511 and VIDEO_COBALT depends on
DRM_I2C_ADV7511=n or COMPILE_TEST.
Suggested-by: Hans Verkuil <hans.verkuil@cisco.com>
Signed-off-by: Anders Roxell <anders.roxell@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Merge back from upstream into media tree, as there are some
patches merged upstream that has pontential of causing
conflicts (one actually rised a conflict already).
Linux 5.2-rc2
* tag 'v5.2-rc2': (377 commits)
Linux 5.2-rc2
random: fix soft lockup when trying to read from an uninitialized blocking pool
tracing: Silence GCC 9 array bounds warning
ext4: fix dcache lookup of !casefolded directories
locking/lock_events: Use this_cpu_add() when necessary
KVM: x86: fix return value for reserved EFER
tools/kvm_stat: fix fields filter for child events
KVM: selftests: Wrap vcpu_nested_state_get/set functions with x86 guard
kvm: selftests: aarch64: compile with warnings on
kvm: selftests: aarch64: fix default vm mode
kvm: selftests: aarch64: dirty_log_test: fix unaligned memslot size
KVM: s390: fix memory slot handling for KVM_SET_USER_MEMORY_REGION
KVM: x86/pmu: do not mask the value that is written to fixed PMUs
KVM: x86/pmu: mask the result of rdpmc according to the width of the counters
x86/kvm/pmu: Set AMD's virt PMU version to 1
KVM: x86: do not spam dmesg with VMCS/VMCB dumps
kvm: Check irqchip mode before assign irqfd
kvm: svm/avic: fix off-by-one in checking host APIC ID
KVM: selftests: do not blindly clobber registers in guest asm
KVM: selftests: Remove duplicated TEST_ASSERT in hyperv_cpuid.c
...
|
|
Embedded systems often connect to sensors or other multimedia
subdevices directly. Currently, to be able to select such a
subdevice (e.g. CONFIG_VIDEO_OV5640) disabling of the auto-
select config option is needed (CONFIG_MEDIA_SUBDRV_AUTOSELECT).
This is inconvenient as the ancillary drivers for a particular
device then need to be selected manually.
Allow to select drivers manually while keeping the auto-select
feature in case EXPERT (selected by EMBEDDED) is enabled.
Signed-off-by: Stefan Agner <stefan@agner.ch>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
This V4L2 subdev driver enables STMicroelectronics MIPID02 device.
Signed-off-by: Mickael Guene <mickael.guene@st.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Building tda1997x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/tda1997x.o: in function `tda1997x_parse_dt'
undefined reference to `v4l2_fwnode_endpoint_parse'
While at it, also sort the selections alphabetically
Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Koen Vandeputte <koen.vandeputte@ncentric.com>
Cc: stable@vger.kernel.org # v4.17+
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Checkpatch wants to use 'help' instead of '---help---':
WARNING: prefer 'help' over '---help---' for new help texts
Let's change it globally at the media subsystem, as otherwise people
would keep using the old way.
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The lens drivers had ended up under the video decoder section; add a new
one just for them, between the camera sensors and flash drivers.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Building adv748x fails now unless V4L2_FWNODE is selected:
drivers/media/i2c/adv748x/adv748x-core.o: In function `adv748x_probe':
adv748x-core.c:(.text+0x1b2c): undefined reference to `v4l2_fwnode_endpoint_parse'
Fixes: 6a18865da8e3 ("media: i2c: adv748x: store number of CSI-2 lanes described in device tree")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Niklas Söderlund <niklas.soderlund+renesas@ragnatech.se>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The SoC camera framework has no functional drivers left, something that
has not changed for years. Move the leftovers to the staging tree.
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Acked-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Register a sub-device to the asynchronous subdevice framework, and also
create subdevice device node.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Create a source pad and set the media controller type to the sensor.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Remove remaining soc_camera specific code and drop soc_camera dependency
from this driver.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Copy the soc_camera based driver in v4l2 sensor driver directory.
This commit just copies the original file without modifying it.
Cc: Guennadi Liakhovetski <g.liakhovetski@gmx.de>
Signed-off-by: Akinobu Mita <akinobu.mita@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
This patch adds driver for Omnivision's ov8856 sensor,
the driver supports following features:
- manual exposure/gain(analog and digital) control support
- two link frequencies
- VBLANK/HBLANK support
- test pattern support
- media controller support
- runtime PM support
- enable Vsync signal output
- supported resolutions
+ 3280x2464 at 30FPS
+ 1640x1232 at 30FPS
Signed-off-by: Ben Kao <ben.kao@intel.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Add initial support for MLX90640 thermal cameras which output an 32x24
greyscale pixel image along with 2 rows of coefficent data.
Because of this the data outputed is really 32x26 and needs the two rows
removed after using the coefficent information to generate processed
images in userspace.
Signed-off-by: Matt Ranostay <matt.ranostay@konsulko.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Initial part of ov9640 transition from soc_camera subsystem to a standalone
v4l2 subdevice. The soc_camera version seems to be used only in Palm Zire72
and in (the future) HTC Magician. On these two devices the support is
broken as pxa_camera driver doesn't use soc_camera anymore. The other
mentions from git grep are "TODOs" (in board-osk.c) or chip names for
unsupported sensors on HW which doesn't use soc_camera at all (irelevant).
Copy the driver files from soc_camera and mark the original ones in the
Kconfig description as obsoleted.
Add config option VIDEO_OV9640 to the build files in drivers/media/i2c.
Signed-off-by: Petr Cvek <petrcvekcz@gmail.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The chip can be configured to output data transitions on the
rising or falling edge of PIXCLK (Datasheet R58:1[9]), default is on the
falling edge.
Parsing the fw-node is made in a subfunction to bundle all (future)
dt-parsing / fw-parsing stuff.
[m.grzeschik@pengutronix.de: Fix inverting clock. INV_PIX_CLOCK bit is set
per default. Set bit to 0 (enable mask bit without value) to enable
falling edge sampling.]
[m.felsch@pengutronix.de: use fwnode helpers]
[m.felsch@pengutronix.de: mv fw parsing into own function]
[m.felsch@pengutronix.de: adapt commit msg]
[sakari.ailus@linux.intel.com: V4L2 API usage changes to compile
on media tree master]
Signed-off-by: Enrico Scholz <enrico.scholz@sigma-chemnitz.de>
Signed-off-by: Michael Grzeschik <m.grzeschik@pengutronix.de>
Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
The imx274 driver uses regmap and the build will fail without it.
Fixes:
drivers/media/i2c/imx274.c:142:21: error: variable ‘imx274_regmap_config’ has initializer but incomplete type
static const struct regmap_config imx274_regmap_config = {
^~~~~~~~~~~~~
drivers/media/i2c/imx274.c:1869:19: error: implicit declaration of function ‘devm_regmap_init_i2c’ [-Werror=implicit-function-declaration]
imx274->regmap = devm_regmap_init_i2c(client, &imx274_regmap_config);
^~~~~~~~~~~~~~~~~~~~
and others.
Signed-off-by: Luca Ceresoli <luca@lucaceresoli.net>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
|
Without CONFIG_HDMI, we get a link error for this driver:
drivers/media/i2c/tda1997x.o: In function `tda1997x_parse_infoframe':
tda1997x.c:(.text+0x2195): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text+0x21b6): undefined reference to `hdmi_infoframe_log'
drivers/media/i2c/tda1997x.o: In function `tda1997x_log_infoframe':
tda1997x.c:(.text.unlikely+0x13d3): undefined reference to `hdmi_infoframe_unpack'
tda1997x.c:(.text.unlikely+0x1426): undefined reference to `hdmi_infoframe_log'
All other drivers in this directory that use HDMI select CONFIG_HDMI,
so do the same here:
Fixes: 9ac0038db9a7 ("media: i2c: Add TDA1997x HDMI receiver driver")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+samsung@kernel.org>
|
