| Age | Commit message (Collapse) | Author |
|---|
|
The AVC protocol uses the same command for tuning and PID filtering and
since dvb-core uses a software zigzagging to do automatic retuning this
could cause all PID filters to be cleared. PID filter information is
now included in all DSD commands to the card.
Background:
There is a problem in the firedtv driver that causes recordings to stop
if the SW zigzag algorithm in dvb-core kicks in with a retune after the
application has set up the PID filters. Since tuning and setting PID
filters uses the same AVC command (DSD) and only the replace subfunction
is supported by the card, it is not possible to do a retune without
setting the PID filters. This means that the PID filtering has to be
sent in each tune.
This problem applies to C and T cards since S and S2 cards tune using a
vendor specific command. The patch corrects the problem by sending the
PID list in each tune. I have tested it on my T card with a good
result.
How to trigger problem: Zap to a channel and output AV to a file, e.g.
"tzap -c channels.conf SVT1 -r -o SVT1.ts". After a short while, pull
the antenna cable from the card. The lock on the channel will disappear
and the TS file will stop increasing in size. Wait a couple of seconds.
Replug the cable again. You will get a lock on the channel again, but
the TS file will never increase in size agains sinze no PIDS are
filtered.
Tested with kaffeine with DVB-T and DVB-C: Fixes retuning after antenna
was plugged out and back in with DVB-T. Does not fix this with DVB-C,
but also doesn't regress on DVB-C.
Signed-off-by: Henrik Kurelid <henrik@kurelid.se>
Signed-off-by: Stefan Richter <stefanr@s5r6.in-berlin.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Attached is a patch which fixes tuning to low frequency channels with
stb0899+tda8261 cards like the KNC TV-Station DVB-S2.
The cause of the issue was a broken if construct, which should have been
an if/else if, so that the setting for the lowest matching frequency is
applied.
Without this patch for example tuning to "arte" on Astra 19.2, 10744MHz
SR22000 failed most times and when it failed the communication between
driver and tda8261 was completely broken.
This problem disappears with the attached patch.
Signed-off-by: Julian Scheel <julian@jusst.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Add new USB ID (1b80:e400) for KWorld PlusTV Dual DVB-T Stick (DVB-T 399U).
The model number on the devices sticker label is "KW-DVB-T 399UR".
Signed-off-by: Mart Raudsepp <mart.raudsepp@artecdesign.ee>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
It seems from other code that it is the dst_type field rather than the
type_flags field that contains values of the form DST_TYPE_IS...
The type_flags field contains values of the form DST_TYPE_HAS...
The semantic match that finds this problem is as follows:
(http://www.emn.fr/x-info/coccinelle/)
// <smpl>
@@ struct dst_state E; @@
(
*E.type_flags ==
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
|
*E.type_flags !=
\( DST_TYPE_IS_SAT\|DST_TYPE_IS_TERR\|DST_TYPE_IS_CABLE\|DST_TYPE_IS_ATSC \)
)
// </smpl>
Cc: Manu Abraham <abraham.manu@gmail.com>
Signed-off-by: Julia Lawall <julia@diku.dk>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds support for Humax/Coex DVB-T USB Stick 2.0 High Speed
which is a very popular tuner sold in Vietnam.
Tested with at least 3 tuners.
Cc: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Pham Thanh Nam <phamthanhnam.ptn@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The card includes Intel ce5039(Zarlink zl10039) tuner
and Intel ce6313 (Zarlink zl10313) demod.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The code from Jan D. Louw with some minor changes.
http://article.gmane.org/gmane.linux.drivers.dvb/38163
Tested with TeVii S630 DVB-S USB card by me (Igor)
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
do_div requires an u64 as the first argument, not a s64.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Acked-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Use unified lgs8gxx frontend instead of reverse engineered lgs8gl5 frontend.
After this patch, lgs8gl5 frontend could be mark as deprecated.
Future development should base on unified lgs8gxx frontend.
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch adds support for the STK7700D USB-DVB-Device.
lsusb identifies it as:
idVendor 0x1164 YUAN High-Tech Development Co., Ltd
idProduct 0x1efc
iProduct 2 STK7700D
The device is build into a Samsung R55-T5500 notebook.
Signed-off-by: Pete Hildebrandt <send2ph@googlemail.com>
Signed-off-by: Patrick Boettcher <pboettcher@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
cinergyInitialize param.flags.
Signed-off-by: Eberhard Mattes <eberhard.mattes@web.de>
Signed-off-by: Thierry MERLE <thierry.merle@free.fr>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Replace printing to magically sized temporary buffer with use
of KERN_CONT for continual printing of eeprom registers dump.
Since deb_info is defined as dprintk, which is conditionally defined
to printk without additional parameters, meaning that deb_info is equivalent
to direct printk (without adding KERN_ facility), we can use KERN_DEBUG and
KERN_CONT in there, eliminating the need for sprintf into temporary buffer
with not easily readable/magical size.
Though it's strange, that deb_info definition uses printk without KERN_
facility and callers don't use it either.
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Create card parameters array in SDMC DM1105 driver.
It is useful for cards with the same pci id, but different
tuners, lnb power control circuits, etc.
Signed-off-by: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
In automatic mode every stop event on SDA line ends repetition.
However, in NetUP Dual card on the same i2c bus we have several devices.
If someone using both adapters to lock simultaneously or working with CAM interface
during lock procedure, it lead to end repetition prematurely quite often.
Set stv0900 i2c repeater to manual mode prevents such situation.
Signed-off-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Signed-off-by: Igor M. Liplianin <liplianin@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The dvb-pll code should do the same thing that
alps_tdee4_stv0297_tuner_set_params() was doing. Except the dvb-pll code
will check for tuner presence when attaching, while the old code didn't.
This tuner appears to not be behind the stv0297's I2C gate but is instead
on a different I2C adapter provided by the flexcop chip. The old code
would turn the I2C gate off each time the tuner was used. I've changed it
to turn the gate off when the tuner is attached and then disable the gate
control function. This should result in the gate staying off, which should
be even better.
[hverkuil@xs4all.nl: fix compile error]
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The code in skystar23_samsung_tbdu18132_tuner_set_params() and
samsung_tbmu24112_tuner_set_params() is equivalent to what the dvb-pll code
does. There could be an issue because the dvb-pll code will probe to check
for the tuner, while the previous code didn't do any checks.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The code in samsung_tdtc9251dh0_calc_regs() is equivalent to what dvb-pll's
code does.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
No datasheet, data take from code in flexcop driver. That code rounded
down the divisor rather than rounding to nearest, which was probably not
intentional and the dvb-pll code will round to nearest.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Tuner parameters determined from code in flexcop driver. That code rounded
the divisor down instead of to the nearest value. This was probably not
intentional and the dvb-pll version will round to nearest.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Tuner parameters taken from flexcop driver. This PLL has a 17 bit divisor
while the dvb-pll driver is designed for 15 bit divisors. It's not a
problem as 15 bits is enough for the tuner's entire range. But if a larger
range was wanted, it could be done by adding additional bands with the
extra divisor bits appearing as band switch bits.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
No datasheet, tuner data comes from code in flexcop driver. This tuner is
also used on the AVerTV 771 supported by the bttv driver, but that code
uses a different tuner configuration, which is surprising.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Values for 'pid' range from 0 to 0x1fff. Therefore 'feed->pid' can never
be equal to both 'pid' and 0x2000. This makes the continue statement have
no effect.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
DMX_ADD_PID allows to add multiple PIDs to a transport stream filter
previously set up with DMX_SET_PES_FILTER and output=DMX_OUT_TSDEMUX_TAP.
DMX_REMOVE_PID is used to drop a PID from a filter.
These ioctls are to be used by readers of /dev/dvb/adapterX/demuxY. They
may be called at any time, i.e. before or after the first filter on the
shared file descriptor was started.
They make it possible to record multiple services without the need to de-
or re-multiplex TS packets.
To accomplish this, dmxdev_filter->feed.ts has been converted to a list
of struct dmxdev_feeds, each containing a PID value and a pointer to a
struct dmx_ts_feed.
Signed-off-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
lgs8gxx: add lgs8g75 demodulator support
Signed-off-by: David T.L. Wong <davidtlwong@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
This patch fixes some checkpatch warnings in mt312-driver.
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
input, inp and i are unsigned. When negative they are wrapped and caught by the
other test.
Cc: Andy Walls <awalls@radix.net>
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Cc: Patrick Boettcher <patrick.boettcher@desy.de>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Igor M. Liplianin <liplianin@netup.ru>
Cc: Srinivasa Deevi <srinivasa.deevi@conexant.com>
Signed-off-by: Joe Perches <joe@perches.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Update KConfig file to enbale selection of SDIO and USB
interfaces, and add dependancy on relevant modules.
[mchehab@redhat.com: fix merge conflicts, remove default: m, add missing endmenu]
Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixed SDIO compilation bugs
Also fixed a memory overrun issue in buffer management.
Signed-off-by: Udi Atar <udia@siano-ms.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Previous changesets broke Hauppauge devices and their GPIO configurations.
This changeset restores the LED & LNA functionality.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
With mode DEVICE_MODE_RAW_TUNER a read occurs past the end of smscore_fw_lkup[].
Subsequently an attempt is made to load the firmware from the resulting
filename.
Signed-off-by: Roel Kluin <roel.kluin@gmail.com>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
properly
This patch changes most frontend drivers to allocate their state structure via
kzalloc and not kmalloc. This is done to properly initialize the
embedded "struct dvb_frontend frontend" field, that they all have.
The visible effect of this struct being uninitalized is, that the member "id"
that is used to set the name of kernel thread is totally random.
Some board drivers (for example cx88-dvb) set this "id" via
videobuf_dvb_alloc_frontend but most do not.
So I at least get random id values for saa7134, flexcop and ttpci based cards.
It looks like this in dmesg:
DVB: registering adapter 1 frontend -10551321 (ST STV0299 DVB-S)
The related kernel thread then also gets a strange name
like "kdvb-ad-1-fe--1".
Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Steven Toth <stoth@linuxtv.org>
Cc: Timothy Lee <timothy.lee@siriushk.com>
Cc: Igor M. Liplianin <liplianin@me.by>
Signed-off-by: Matthias Schwarzott <zzam@gentoo.org>
Acked-by: Andreas Oberritter <obi@linuxtv.org>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
siano uses input_*() functions so it should depend on INPUT
to prevent build errors:
ERROR: "input_event" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_register_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_free_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_unregister_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
ERROR: "input_allocate_device" [drivers/media/dvb/siano/sms1xxx.ko] undefined!
Cc: Michael Krufky <mkrufky@linuxtv.org>
Cc: Uri Shkolnik <uris@siano-ms.com>
Signed-off-by: Randy Dunlap <randy.dunlap@oracle.com>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Remove the following build warning:
sms-cards.c: In function 'sms_board_event':
sms-cards.c:120: warning: unused variable 'board'
Thanks to Hans Verkuil for pointing this out.
The problem code has been #if 0'd for now, this will likely be
used again in the future, once the event interface is complete.
Cc: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
The current GPIO configuration breaks all Hauppauge devices.
The code being removed affects Hauppauge devices only,
and is the cause of the breakage.
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Moving BOOT fixes problem.
Signed-off-by: Nils Kassube <kassube@gmx.net>
Acked-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Douglas Schilling Landgraf <dougsland@redhat.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Fixes stack corruption bug present in dump_regs function of zl10353 and
qt1010 drivers: the buffer buf was one byte smaller than required -
there are 4 chars for address prefix, 16 * 3 chars for dump of 16 eeprom
bytes per line and 1 byte for zero ending the string required, i.e. 53
bytes, but only 52 were provided.
The one byte missing in stack based buffer buf can cause stack
corruption possibly leading to kernel oops, as discovered originally
with af9015 driver (af9015: fix stack corruption bug).
Signed-off-by: Jan Nikitenko <jan.nikitenko@gmail.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
master.kernel.org:/pub/scm/linux/kernel/git/davem/net-2.6
Conflicts:
arch/microblaze/include/asm/socket.h
|
|
A recent patch didn't take into account that frontends can be compiled into
the kernel. Or that frontends compiled as modules can't be used by the
b2c2 driver if it is not a module itself.
Some frontends require multiple drivers, e.g. a demod driver and a tuner
driver. The code for the frontend support was getting added if the demod
driver was available. Change this to also require any needed tuner or SEC
drivers as well.
Signed-off-by: Trent Piepho <xyzzy@speakeasy.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Request demodulator auto-detect transmission parameters in case of
garbage parameters provided by application for compatibility.
That's needed at least for MPlayer compatibility currently.
Thanks to Jelle de Jong for reporting issue and providing SSH access to
Devin for debugging.
Thanks to Devin Heitmueller for hard debug work he did to find that bug.
Cc: Devin Heitmueller <dheitmueller@kernellabs.com>
Cc: Jelle de Jong <jelledejong@powercraft.nl>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
* Remove smp_lock.h from files which don't need it (including some headers!)
* Add smp_lock.h to files which do need it
* Make smp_lock.h include conditional in hardirq.h
It's needed only for one kernel_locked() usage which is under CONFIG_PREEMPT
This will make hardirq.h inclusion cheaper for every PREEMPT=n config
(which includes allmodconfig/allyesconfig, BTW)
Signed-off-by: Alexey Dobriyan <adobriyan@gmail.com>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
This patch is the result of an automatic spatch transformation to convert
all ndo_start_xmit() return values of 0 to NETDEV_TX_OK.
Some occurences are missed by the automatic conversion, those will be
handled in a seperate patch.
Signed-off-by: Patrick McHardy <kaber@trash.net>
Signed-off-by: David S. Miller <davem@davemloft.net>
|
|
If I2C is not enabled, then we shouldn't build ttpci_eeprom.c.
Signed-off-by: Hans Verkuil <hverkuil@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
table was being
loaded for a given chip version. This would cause the optimization in
tuning not to be applied and thus a failed expectation, in tuning speed
increment. The patch swaps the tables in use. It also fixes a possible
one in a million condition where state->dev_ver implies an older Cut
(Cut < 2.0, eventhough the driver doesn't attach to any Cut older than
2.0) or even negative (due to a bad I2C bus master driver) for the card
combination.
Thanks to Mauro Carvalho Chehab <mchehab@infradead.org> for pointing
out the issue at large.
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
drivers/media/dvb/frontends/stv090x.c: In function ‘stv090x_optimize_carloop_short’:
drivers/media/dvb/frontends/stv090x.c:2677: warning: ‘short_crl’ may be used uninitialized in this function
Signed-off-by: Manu Abraham <manu@linuxtv.org>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
|
Thanks for Terry Wu for pointing out the missing entry.
Cc: Terry Wu <terrywu2009@gmail.com>
Signed-off-by: Michael Krufky <mkrufky@kernellabs.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@redhat.com>
|
