| Age | Commit message (Collapse) | Author |
|---|
|
While cab_state->state gives a quite accurate indication of the demod
signal status, it might be incorrect if cab_algo() wasn't able to
determine the exact status, with cab_algo() being the only place where
this status was updated from, and it is only called upon tuning to new
parameters passed to set_frontend(). Thus, the status will be wrong
until the demod is retuned. With the cab_signal_type parsing in
read_status(), this results in unusual fe_states like FE_HAS_SIGNAL |
FE_HAS_CARRIER | FE_HAS_LOCK, which, while userspace applications check
for FE_HAS_LOCK and work fine, leads to missing CNR or UCB stats.
Fix this by re-reading CAB_FSM_STATUS and updating cab_state->state() in
read_status(). While at it, refactor the fsm/qamfeclock and the
fsm->signaltype parsing into separate functions to make things cleaner
and deduplicate code. Also, assume full QAM FEC lock equals full
FE_STATUS.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Don't populate array dib0090_tuning_table_cband_7090e_aci on the stack but
instead make it static. Makes the object code smaller by over 180 bytes:
Before:
text data bss dec hex filename
40052 7320 192 47564 b9cc dib0090.o
After:
text data bss dec hex filename
39780 7408 192 47380 b914 dib0090.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Don't populate const arrays on the stack but instead make them static.
Makes the object code smaller by over 1800 bytes:
Before:
text data bss dec hex filename
94100 9160 0 103260 1935c drxj.o
After:
text data bss dec hex filename
91044 10400 0 101444 18c44 drxj.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Don't populate arrays slowIncrDecLUT and fastIncrDecLUT on the stack but
instead make them static. Makes the object code smaller by over 100 bytes:
text data bss dec hex filename
27776 832 64 28672 7000 drxd_hard.o
text data bss dec hex filename
27530 976 64 28570 6f9a drxd_hard.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Discovered using w_scan when scanning DVB-T/T2: When w_scan goes from -T
to -T2, it does so without stopping the frontend using .sleep. Due to
this, the demod operation mode isn't re-setup, but as it still is in
STATE_ACTIVE_TC, PLP and T2 Profile are set up, but only retune_active()
is called, leaving the demod in T mode, thus not operable on any T2
frequency.
Fix this by putting the demod to sleep if priv->system isn't equal to
p->delsys. To properly accomplish this, sleep_tc() is split into
sleep_tc() and shutdown_tc(), where sleep_tc() will only perform the
sleep operation, while shutdown_tc() additionally performs the full
demod shutdown (to keep the behaviour when the .sleep FE_OP is called).
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Don't populate arrays on the stack but make them static. Makes
the object code smaller:
Before:
text data bss dec hex filename
89299 21704 64 111067 1b1db cxd2841er.o
After:
text data bss dec hex filename
85823 23432 64 109319 1ab07 cxd2841er.o
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check for i2c_algorithm structures that are only stored in
the algo field of an i2c_adapter structure. This field is
declared const, so i2c_algorithm structures that have this
property can be declared as const also.
This issue was identified using Coccinelle and the following
semantic patch:
@r disable optional_qualifier@
identifier i;
position p;
@@
static struct i2c_algorithm i@p = { ... };
@ok@
identifier r.i;
struct i2c_adapter e;
position p;
@@
e.algo = &i@p;
@bad@
position p != {r.p,ok.p};
identifier r.i;
@@
i@p
@depends on !bad disable optional_qualifier@
identifier r.i;
@@
static
+const
struct i2c_algorithm i = { ... };
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Return 0 instead of -EINVAL in get_frontend if no demod mode is active.
This fixes ie. dvb-fe-tool getting confused and assuming a DVBv3 FE on idle
frontends when the FE has been put to sleep using sleep().
Also, in read_status(), don't immediately return when no demod is active,
so the remaining code has a chance to clear the signal statistics.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This adds a frontend driver for the ST STV6111 DVB-S/S2 tuners. Like the
stv0910 demod frontend driver, this driver originates from the Digital
Devices' dddvb vendor driver package as of version 0.9.29, and was cleaned
up aswell. No functionality had to be removed though. Any camel case has
been converted to kernel_case, fixup patch has been proposed upstream.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This was missing from the frontend_ops.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Original code at least has some signed/unsigned issues, resulting in
values like 32dBm. Implement signal strength readout to work without
asking the attached tuner, and use a lookup table instead of log calc.
Values reported appear plausible, gathered from feedback from several
testers.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Implements stream_id filter and scrambling code setup in start() and also
sets FE_CAN_MULTISTREAM in frontend_ops. This enables the driver to
properly receive and handle multistream transponders, functionality has
been reported working fine by testers with access to such streams, in
conjunction with VDR on the userspace side.
The code snippet originates from the original vendor's dddvb driver
package and has been made working properly with the current in-kernel
DVB core API.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Fixes smatch error:
drivers/media/dvb-frontends/stv0910.c:715 dvbs2_nbch() error: buffer overflow 'nbch[fectype]' 2 <= 28
Also, fixes the nbch array table by adding the DUMMY_PLF element at the top
to match the enums (table element order was off by one before).
Patch sent upstream aswell.
Cc: Ralph Metzler <rjkm@metzlerbros.de>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This adds a multi frontend driver for the ST STV0910 DVB-S/S2 demodulator
frontends. The driver code originates from the Digital Devices' dddvb
vendor driver package as of version 0.9.29, and has been cleaned up from
core API usage which isn't supported yet in the kernel, and additionally
all obvious style issues have been resolved. All camel case and allcaps
have been converted to kernel_case and lowercase. Patches have been sent
to the vendor package maintainers to fix this aswell. Signal statistics
acquisition has been refactored to comply with standards.
Permission to reuse and mainline the driver code was formally granted by
Ralph Metzler <rjkm@metzlerbros.de>.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Tested-by: Richard Scobie <r.scobie@clear.net.nz>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The stv0367 driver provide a lot of status on its state machine.
Change the logic to provide more information about frontend locking
status. Also, while any detailed status isn't available, provide a more
complete FE_STATUS for DVB-T.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
|
|
Provide QAM/DVB-C signal strength in decibel scale. Values returned from
stv0367cab_get_rf_lvl() are good but need to be multiplied as they're in
1dBm precision.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Since the other statistics are read when fe_status conditions are TRUE,
change the ucblocks readout logic to match this aswell.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
While there's a test at the SNR calculus to avoid division by
zero, it will still follow the path that would do the division.
So, add a missing break there.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add signal-to-noise-ratio as provided by the demodulator in decibel scale.
QAM/DVB-C needs some intlog calculation to have usable dB values, OFDM/
DVB-T values from the demod look alright already and are provided as-is.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When the demod driver puts the demod into sleep or shutdown state and it's
status is then polled e.g. via "dvb-fe-tool -m", i2c errors are printed
to the kernel log. If the last delsys was DVB-T/T2:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=26
and if it was DVB-C:
cxd2841er: i2c wr failed=-5 addr=6c reg=00 len=1
cxd2841er: i2c rd failed=-5 addr=6c reg=49
This happens when read_status unconditionally calls into the
read_signal_strength() function which triggers the read_agc_gain_*()
functions, where these registered are polled.
This isn't a critical thing since when the demod is active again, no more
such errors are logged, however this might make users suspecting defects.
Fix this by requiring STATE_ACTIVE_* in priv->state. If it isn't in any
active state, additionally set the strength scale to NOT_AVAILABLE.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The read_snr() functions currently do some magic to return relative scale
values when called. Split out register readouts into separate functions
so the functionality can be reused in some other way.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
This adds the basics to stv0367ddb_read_status() to be able to properly
provide signal statistics in DVBv5 format. Also adds UCB readout and
provides those values. Also, don't return -EINVAL in ddb_read_status()
if active_demod_state indicates no delivery system.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use dev_dbg() in conjunction with the %*ph format macro to print the vmon
status debug, thus hiding continuous hexdumping from default log levels.
Also, change the attach success log line from error to info severity.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
DRX_S9TOS16 and DRX_S24TODRXFREQ are simply not used. Furthermore,
sign_extend32() should be used for sign extension. (Also, the comment
describing DRX_S24TODRXFREQ was wrong). So remove these macros.
Signed-off-by: Martin Kepplinger <martink@posteo.de>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
While committing a change on em28xx, I got a warning of a
typo there. So, fix it on em28xx and on two other media drivers
with the same typo.
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Move power-up and power-down functionality to init/sleep ops and
get rid of old function.
Fixes and simplifies power-up functionality slightly.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Refactor firmware download routine.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Removed register writes are already chip defaults, are not required,
are set later or belong to AF9015 USB interface.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
On serial TS mode output pin could be selected from D0 or D7.
Add configuration option to for it.
Rename TS mode config option prefix from AF9013_TS_ to AF9013_TS_MODE_.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add support for DVBv5 CNR.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use typical (return 0/goto err/return err) error handling everywhere.
Add missing error handling where missing.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Use regmap for register access. Own low level i2c read and write
routines for regmap is still needed because chip uses single command
byte in addition to typical i2c register access.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
We can simplify logging as we now have a proper i2c client
to pass for kernel dev_* logging functions.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Replace own binary division with 64-bit multiply and division.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Add kernel i2c driver bindings.
That allows dev_* logging, regmap and more.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
It shorten, as typed chars, access to config values as there is one
pointer less. Also, when config/platform data is passed to driver there
could be some values that are not relevant to store state as such or
not needed to store at all.
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Check return value from call to af9013_wr_regs(), so in case of
error print debug message and return.
Addresses-Coverity-ID: 1227035
Signed-off-by: Gustavo A. R. Silva <garsilva@embeddedor.com>
Signed-off-by: Antti Palosaari <crope@iki.fi>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
On DVB-T/T2 at least, SNR might be reported as >2500dB, which not only is
just wrong but also ridiculous, so fix this by improving the conversion
of the register value.
The INTLOG10X100 function/macro and the way the values are converted were
both taken from DD's cxd2843 driver.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Bits 3 and 4 of the TSCONFIG register are important for certain hardware
constellations, in that they need to be zeroed. Add a configuration flag
to toggle this.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Adds a flag to enable or disable the IFAGCNEG bit in cxd2841er_init_tc().
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Don't wait for FE_HAS_LOCK in set_frontend_tc() and thus don't hammer the
lock status register with inquiries when CXD2841ER_NO_WAIT_LOCK is set
in the configuration, which also unneccessarily blocks applications until
a TS LOCK has been acquired. Rather, API and applications will check for
a TS LOCK by utilising the tune fe_op, read_status and get_frontend ops,
which is sufficient.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
When AUTO_IFHZ is set and the tuner is supposed to provide proper IF speed
values, it should be possible to have the tuner setup take place before
the demod is configured, else the demod might be configured with either
wrong (old), or even no values at all, which obviously will cause issues.
To set this behaviour in the most flexible way, this is done with a
separate flag instead of making this depend on AUTO_IFHZ.
It should be evaluated if tuning shouldn't take place earlier in all cases
and hardware constellations.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
The Sony CXD28xx demods may have other tuner types attached to them (e.g.
NXP TDA18212), so don't mandatorily configure and enable the ASCOT
functionality, but make this conditional by a config flag.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
|
Some constellations work/need a serial TS transport mode. This adds a flag
that will toggle set up of such mode.
Signed-off-by: Daniel Scheller <d.scheller@gmx.net>
Acked-by: Abylay Ospan <aospan@netup.ru>
Signed-off-by: Mauro Carvalho Chehab <mchehab@s-opensource.com>
|
