| Age | Commit message (Collapse) | Author |
|---|
|
Stopping external metadata arrays during resync/recovery causes
retries, loop of interrupting and starting reconstruction, until it
hit at good moment to stop completely. While these retries
curr_mark_cnt can be small- especially on HDD drives, so subtraction
result can be smaller than 0. However it is casted to uint without
checking. As a result of it the status bar in /proc/mdstat while stopping
is strange (it jumps between 0% and 99%).
The real problem occurs here after commit 72deb455b5ec ("block: remove
CONFIG_LBDAF"). Sector_div() macro has been changed, now the
divisor is casted to uint32. For db = -8 the divisior(db/32-1) becomes 0.
Check if db value can be really counted and replace these macro by
div64_u64() inline.
Signed-off-by: Mariusz Tkaczyk <mariusz.tkaczyk@intel.com>
Signed-off-by: Song Liu <songliubraving@fb.com>
|
|
When people set a writeback percent via sysfs file,
/sys/block/bcache<N>/bcache/writeback_percent
current code directly sets BCACHE_DEV_WB_RUNNING to dc->disk.flags
and schedules kworker dc->writeback_rate_update.
If there is no cache set attached to, the writeback kernel thread is
not running indeed, running dc->writeback_rate_update does not make
sense and may cause NULL pointer deference when reference cache set
pointer inside update_writeback_rate().
This patch checks whether the cache set point (dc->disk.c) is NULL in
sysfs interface handler, and only set BCACHE_DEV_WB_RUNNING and
schedule dc->writeback_rate_update when dc->disk.c is not NULL (it
means the cache device is attached to a cache set).
This problem might be introduced from initial bcache commit, but
commit 3fd47bfe55b0 ("bcache: stop dc->writeback_rate_update properly")
changes part of the original code piece, so I add 'Fixes: 3fd47bfe55b0'
to indicate from which commit this patch can be applied.
Fixes: 3fd47bfe55b0 ("bcache: stop dc->writeback_rate_update properly")
Reported-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Bjørn Forsman <bjorn.forsman@gmail.com>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Recently people report bcache code compiled with gcc9 is broken, one of
the buggy behavior I observe is that two adjacent 4KB I/Os should merge
into one but they don't. Finally it turns out to be a stack corruption
caused by macro PRECEDING_KEY().
See how PRECEDING_KEY() is defined in bset.h,
437 #define PRECEDING_KEY(_k) \
438 ({ \
439 struct bkey *_ret = NULL; \
440 \
441 if (KEY_INODE(_k) || KEY_OFFSET(_k)) { \
442 _ret = &KEY(KEY_INODE(_k), KEY_OFFSET(_k), 0); \
443 \
444 if (!_ret->low) \
445 _ret->high--; \
446 _ret->low--; \
447 } \
448 \
449 _ret; \
450 })
At line 442, _ret points to address of a on-stack variable combined by
KEY(), the life range of this on-stack variable is in line 442-446,
once _ret is returned to bch_btree_insert_key(), the returned address
points to an invalid stack address and this address is overwritten in
the following called bch_btree_iter_init(). Then argument 'search' of
bch_btree_iter_init() points to some address inside stackframe of
bch_btree_iter_init(), exact address depends on how the compiler
allocates stack space. Now the stack is corrupted.
Fixes: 0eacac22034c ("bcache: PRECEDING_KEY()")
Signed-off-by: Coly Li <colyli@suse.de>
Reviewed-by: Rolf Fokkens <rolf@rolffokkens.nl>
Reviewed-by: Pierre JUHEN <pierre.juhen@orange.fr>
Tested-by: Shenghui Wang <shhuiw@foxmail.com>
Tested-by: Pierre JUHEN <pierre.juhen@orange.fr>
Cc: Kent Overstreet <kent.overstreet@gmail.com>
Cc: Nix <nix@esperi.org.uk>
Cc: stable@vger.kernel.org
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Based on 1 normalized pattern(s):
this file is released under the gplv2
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 68 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Armijn Hemel <armijn@tjaldur.nl>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190531190114.292346262@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms and conditions of the gnu general public license
version 2 as published by the free software foundation this program
is distributed in the hope it will be useful but without any
warranty without even the implied warranty of merchantability or
fitness for a particular purpose see the gnu general public license
for more details
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-only
has been chosen to replace the boilerplate/reference in 263 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Alexios Zavras <alexios.zavras@intel.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190529141901.208660670@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details you
should have received a copy of the gnu general public license along
with this program if not write to the free software foundation inc
59 temple place suite 330 boston ma 02111 1307 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 1334 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.113240726@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 3029 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm
Pull libnvdimm fixes from Dan Williams:
- Fix a regression that disabled device-mapper dax support
- Remove unnecessary hardened-user-copy overhead (>30%) for dax
read(2)/write(2).
- Fix some compilation warnings.
* tag 'libnvdimm-fixes-5.2-rc2' of git://git.kernel.org/pub/scm/linux/kernel/git/nvdimm/nvdimm:
libnvdimm/pmem: Bypass CONFIG_HARDENED_USERCOPY overhead
dax: Arrange for dax_supported check to span multiple devices
libnvdimm: Fix compilation warnings with W=1
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core
Pule more SPDX updates from Greg KH:
"Here is another set of reviewed patches that adds SPDX tags to
different kernel files, based on a set of rules that are being used to
parse the comments to try to determine that the license of the file is
"GPL-2.0-or-later".
Only the "obvious" versions of these matches are included here, a
number of "non-obvious" variants of text have been found but those
have been postponed for later review and analysis.
These patches have been out for review on the linux-spdx@vger mailing
list, and while they were created by automatic tools, they were
hand-verified by a bunch of different people, all whom names are on
the patches are reviewers"
* tag 'spdx-5.2-rc2-2' of git://git.kernel.org/pub/scm/linux/kernel/git/gregkh/driver-core: (85 commits)
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 125
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 123
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 122
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 121
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 120
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 119
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 118
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 116
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 114
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 113
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 112
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 111
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 110
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 106
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 105
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 104
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 103
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 102
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 101
treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 98
...
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version you should have received a copy of the gnu general
public license for example usr src linux copying if not write to the
free software foundation inc 675 mass ave cambridge ma 02139 usa
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 20 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.552543146@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Based on 1 normalized pattern(s):
this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 or at your option any
later version
extracted by the scancode license scanner the SPDX license identifier
GPL-2.0-or-later
has been chosen to replace the boilerplate/reference in 11 file(s).
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190520170858.370933192@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper fix from Mike Snitzer:
"Fix a particularly glaring oversight in a DM core commit from 5.1 that
doesn't properly trim special IOs (e.g. discards) relative to
corresponding target's max_io_len_target_boundary()"
* tag 'for-5.2/dm-fix-1' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm: make sure to obey max_io_len_target_boundary
|
|
Commit 61697a6abd24 ("dm: eliminate 'split_discard_bios' flag from DM
target interface") incorrectly removed code from
__send_changing_extent_only() that is required to impose a per-target IO
boundary on IO that exceeds max_io_len_target_boundary(). Otherwise
"special" IO (e.g. DISCARD, WRITE SAME, WRITE ZEROES) can write beyond
where allowed.
Fix this by restoring the max_io_len_target_boundary() limit in
__send_changing_extent_only()
Fixes: 61697a6abd24 ("dm: eliminate 'split_discard_bios' flag from DM target interface")
Cc: stable@vger.kernel.org # 5.1+
Signed-off-by: Michael Lass <bevan@bi-co.net>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Add SPDX license identifiers to all Make/Kconfig files which:
- Have no license information of any form
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have MODULE_LICENCE("GPL*") inside which was used in the initial
scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Add SPDX license identifiers to all files which:
- Have no license information of any form
- Have EXPORT_.*_SYMBOL_GPL inside which was used in the
initial scan/conversion to ignore the file
These files fall under the project license, GPL v2 only. The resulting SPDX
license identifier is:
GPL-2.0-only
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
Pankaj reports that starting with commit ad428cdb525a "dax: Check the
end of the block-device capacity with dax_direct_access()" device-mapper
no longer allows dax operation. This results from the stricter checks in
__bdev_dax_supported() that validate that the start and end of a
block-device map to the same 'pagemap' instance.
Teach the dax-core and device-mapper to validate the 'pagemap' on a
per-target basis. This is accomplished by refactoring the
bdev_dax_supported() internals into generic_fsdax_supported() which
takes a sector range to validate. Consequently generic_fsdax_supported()
is suitable to be used in a device-mapper ->iterate_devices() callback.
A new ->dax_supported() operation is added to allow composite devices to
split and route upper-level bdev_dax_supported() requests.
Fixes: ad428cdb525a ("dax: Check the end of the block-device...")
Cc: <stable@vger.kernel.org>
Cc: Ira Weiny <ira.weiny@intel.com>
Cc: Dave Jiang <dave.jiang@intel.com>
Cc: Keith Busch <keith.busch@intel.com>
Cc: Matthew Wilcox <willy@infradead.org>
Cc: Vishal Verma <vishal.l.verma@intel.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Reported-by: Pankaj Gupta <pagupta@redhat.com>
Reviewed-by: Pankaj Gupta <pagupta@redhat.com>
Tested-by: Pankaj Gupta <pagupta@redhat.com>
Tested-by: Vaibhav Jain <vaibhav@linux.ibm.com>
Reviewed-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Dan Williams <dan.j.williams@intel.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper updates from Mike Snitzer:
- Improve DM snapshot target's scalability by using finer grained
locking. Requires some list_bl interface improvements.
- Add ability for DM integrity to use a bitmap mode, that tracks
regions where data and metadata are out of sync, instead of using a
journal.
- Improve DM thin provisioning target to not write metadata changes to
disk if the thin-pool and associated thin devices are merely
activated but not used. This avoids metadata corruption due to
concurrent activation of thin devices across different OS instances
(e.g. split brain scenarios, which ultimately would be avoided if
proper device filters were used -- but not having proper filtering
has proven a very common configuration mistake)
- Fix missing call to path selector type->end_io in DM multipath. This
fixes reported performance problems due to inaccurate path selector
IO accounting causing an imbalance of IO (e.g. avoiding issuing IO to
particular path due to it seemingly being heavily used).
- Fix bug in DM cache metadata's loading of its discard bitset that
could lead to all cache blocks being discarded if the very first
cache block was discarded (thankfully in practice the first cache
block is generally in use; be it FS superblock, partition table, disk
label, etc).
- Add testing-only DM dust target which simulates a device that has
failing sectors and/or read failures.
- Fix a DM init error path reference count hang that caused boot hangs
if user supplied malformed input on kernel commandline.
- Fix a couple issues with DM crypt target's logging being overly
verbose or lacking context.
- Various other small fixes to DM init, DM multipath, DM zoned, and DM
crypt.
* tag 'for-5.2/dm-changes-v2' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm: (42 commits)
dm: fix a couple brace coding style issues
dm crypt: print device name in integrity error message
dm crypt: move detailed message into debug level
dm ioctl: fix hang in early create error condition
dm integrity: whitespace, coding style and dead code cleanup
dm integrity: implement synchronous mode for reboot handling
dm integrity: handle machine reboot in bitmap mode
dm integrity: add a bitmap mode
dm integrity: introduce a function add_new_range_and_wait()
dm integrity: allow large ranges to be described
dm ingerity: pass size to dm_integrity_alloc_page_list()
dm integrity: introduce rw_journal_sectors()
dm integrity: update documentation
dm integrity: don't report unused options
dm integrity: don't check null pointer before kvfree and vfree
dm integrity: correctly calculate the size of metadata area
dm dust: Make dm_dust_init and dm_dust_exit static
dm dust: remove redundant unsigned comparison to less than zero
dm mpath: always free attached_handler_name in parse_path()
dm init: fix max devices/targets checks
...
|
|
Signed-off-by: Sheetal Singala <2396sheetal@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
This message should better identify the DM device with the integrity
failure.
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The information about tag size should not be printed without debug info
set. Also print device major:minor in the error message to identify the
device instance.
Also use rate limiting and debug level for info about used crypto API
implementaton. This is important because during online reencryption
the existing message saturates syslog (because we are moving hotzone
across the whole device).
Cc: stable@vger.kernel.org
Signed-off-by: Milan Broz <gmazyland@gmail.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The dm_early_create() function (which deals with "dm-mod.create=" kernel
command line option) calls dm_hash_insert() who gets an extra reference
to the md object.
In case of failure, this reference wasn't being released, causing
dm_destroy() to hang, thus hanging the whole boot process.
Fix this by calling __hash_remove() in the error path.
Fixes: 6bbc923dfcf57d ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Just some things that stood out like a sore thumb.
Also, converted some printk(KERN_CRIT, ...) to DMCRIT(...)
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Unfortunatelly, there may be bios coming even after the reboot notifier
was called. We don't want these bios to make the bitmap dirty again.
To address this, implement a synchronous mode - when a bio is about to
be terminated, we clean the bitmap and terminate the bio after the clean
operation succeeds. This obviously slows down bio processing, but it
makes sure that when all bios are finished, the bitmap will be clean.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When in bitmap mode the bitmap must be cleared when rebooting. This
commit adds the reboot hook.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Introduce an alternate mode of operation where dm-integrity uses a
bitmap instead of a journal. If a bit in the bitmap is 1, the
corresponding region's data and integrity tags are not synchronized - if
the machine crashes, the unsynchronized regions will be recalculated.
The bitmap mode is faster than the journal mode, because we don't have
to write the data twice, but it is also less reliable, because if data
corruption happens when the machine crashes, it may not be detected.
Benchmark results for an SSD connected to a SATA300 port, when doing
large linear writes with dd:
buffered I/O:
raw device throughput - 245MB/s
dm-integrity with journaling - 120MB/s
dm-integrity with bitmap - 238MB/s
direct I/O with 1MB block size:
raw device throughput - 248MB/s
dm-integrity with journaling - 123MB/s
dm-integrity with bitmap - 223MB/s
For more info see dm-integrity in Documentation/device-mapper/
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Introduce a function add_new_range_and_wait() in order to avoid
repetitive code. It will be used in the following commit.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pull block updates from Jens Axboe:
"Nothing major in this series, just fixes and improvements all over the
map. This contains:
- Series of fixes for sed-opal (David, Jonas)
- Fixes and performance tweaks for BFQ (via Paolo)
- Set of fixes for bcache (via Coly)
- Set of fixes for md (via Song)
- Enabling multi-page for passthrough requests (Ming)
- Queue release fix series (Ming)
- Device notification improvements (Martin)
- Propagate underlying device rotational status in loop (Holger)
- Removal of mtip32xx trim support, which has been disabled for years
(Christoph)
- Improvement and cleanup of nvme command handling (Christoph)
- Add block SPDX tags (Christoph)
- Cleanup/hardening of bio/bvec iteration (Christoph)
- A few NVMe pull requests (Christoph)
- Removal of CONFIG_LBDAF (Christoph)
- Various little fixes here and there"
* tag 'for-5.2/block-20190507' of git://git.kernel.dk/linux-block: (164 commits)
block: fix mismerge in bvec_advance
block: don't drain in-progress dispatch in blk_cleanup_queue()
blk-mq: move cancel of hctx->run_work into blk_mq_hw_sysfs_release
blk-mq: always free hctx after request queue is freed
blk-mq: split blk_mq_alloc_and_init_hctx into two parts
blk-mq: free hw queue's resource in hctx's release handler
blk-mq: move cancel of requeue_work into blk_mq_release
blk-mq: grab .q_usage_counter when queuing request from plug code path
block: fix function name in comment
nvmet: protect discovery change log event list iteration
nvme: mark nvme_core_init and nvme_core_exit static
nvme: move command size checks to the core
nvme-fabrics: check more command sizes
nvme-pci: check more command sizes
nvme-pci: remove an unneeded variable initialization
nvme-pci: unquiesce admin queue on shutdown
nvme-pci: shutdown on timeout during deletion
nvme-pci: fix psdt field for single segment sgls
nvme-multipath: don't print ANA group state by default
nvme-multipath: split bios with the ns_head bio_set before submitting
...
|
|
Change n_sectors data type from unsigned to sector_t. Following commits
will need to lock large ranges.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Pass size to dm_integrity_alloc_page_list(). This is needed so
following commits can pass a size that is different from
ic->journal_pages.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Introduce a function rw_journal_sectors() that takes sector and length
as its arguments instead of a section and the number of sections.
This functions will be used in further patches.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Update documentation with the "meta_device" parameter and flags.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
If we are not journaling, don't report journaling options in the table
status.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The functions kfree, vfree and kvfree do nothing if we pass a NULL
pointer to them. So we don't need to test the pointer for NULL.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When we use separate devices for data and metadata, dm-integrity would
incorrectly calculate the size of the metadata device as if it had
512-byte block size - and it would refuse activation with larger block
size and smaller metadata device.
Fix this so that it takes actual block size into account, which fixes
the following reported issue:
https://gitlab.com/cryptsetup/cryptsetup/issues/450
Fixes: 356d9d52e122 ("dm integrity: allow separate metadata device")
Cc: stable@vger.kernel.org # v4.19+
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Fix sparse warnings:
drivers/md/dm-dust.c:495:12: warning: symbol 'dm_dust_init' was not declared. Should it be static?
drivers/md/dm-dust.c:505:13: warning: symbol 'dm_dust_exit' was not declared. Should it be static?
Reported-by: Hulk Robot <hulkci@huawei.com>
Signed-off-by: YueHaibing <yuehaibing@huawei.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Variable block is an unsigned long long hence the less than zero
comparison is always false, hence it is redundant and can be removed.
Addresses-Coverity: ("Unsigned compared against 0")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Reviewed-by: Bryan Gurney <bgurney@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6
Pull crypto update from Herbert Xu:
"API:
- Add support for AEAD in simd
- Add fuzz testing to testmgr
- Add panic_on_fail module parameter to testmgr
- Use per-CPU struct instead multiple variables in scompress
- Change verify API for akcipher
Algorithms:
- Convert x86 AEAD algorithms over to simd
- Forbid 2-key 3DES in FIPS mode
- Add EC-RDSA (GOST 34.10) algorithm
Drivers:
- Set output IV with ctr-aes in crypto4xx
- Set output IV in rockchip
- Fix potential length overflow with hashing in sun4i-ss
- Fix computation error with ctr in vmx
- Add SM4 protected keys support in ccree
- Remove long-broken mxc-scc driver
- Add rfc4106(gcm(aes)) cipher support in cavium/nitrox"
* 'linus' of git://git.kernel.org/pub/scm/linux/kernel/git/herbert/crypto-2.6: (179 commits)
crypto: ccree - use a proper le32 type for le32 val
crypto: ccree - remove set but not used variable 'du_size'
crypto: ccree - Make cc_sec_disable static
crypto: ccree - fix spelling mistake "protedcted" -> "protected"
crypto: caam/qi2 - generate hash keys in-place
crypto: caam/qi2 - fix DMA mapping of stack memory
crypto: caam/qi2 - fix zero-length buffer DMA mapping
crypto: stm32/cryp - update to return iv_out
crypto: stm32/cryp - remove request mutex protection
crypto: stm32/cryp - add weak key check for DES
crypto: atmel - remove set but not used variable 'alg_name'
crypto: picoxcell - Use dev_get_drvdata()
crypto: crypto4xx - get rid of redundant using_sd variable
crypto: crypto4xx - use sync skcipher for fallback
crypto: crypto4xx - fix cfb and ofb "overran dst buffer" issues
crypto: crypto4xx - fix ctr-aes missing output IV
crypto: ecrdsa - select ASN1 and OID_REGISTRY for EC-RDSA
crypto: ux500 - use ccflags-y instead of CFLAGS_<basename>.o
crypto: ccree - handle tee fips error during power management resume
crypto: ccree - add function to handle cryptocell tee fips error
...
|
|
It's not used outside this file.
Fixes: 631207314d88 ("bcache: fix failure in journal relplay")
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit b592211c33f7 ("dm mpath: fix attached_handler_name leak and
dangling hw_handler_name pointer") fixed a memory leak for the case
where setup_scsi_dh() returns failure. But setup_scsi_dh may return
success and not "use" attached_handler_name if the
retain_attached_hwhandler flag is not set on the map. As setup_scsi_sh
properly "steals" the pointer by nullifying it, freeing it
unconditionally in parse_path() is safe.
Fixes: b592211c33f7 ("dm mpath: fix attached_handler_name leak and dangling hw_handler_name pointer")
Cc: stable@vger.kernel.org
Reported-by: Yufen Yu <yuyufen@huawei.com>
Signed-off-by: Martin Wilck <mwilck@suse.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
dm-init should allow up to DM_MAX_{DEVICES,TARGETS} for devices/targets,
and not DM_MAX_{DEVICES,TARGETS} - 1.
Fix the checks and also fix the error message when the number of devices
is surpassed.
Fixes: 6bbc923dfcf57d ("dm: add support to directly boot to a mapped device")
Cc: stable@vger.kernel.org
Signed-off-by: Helen Koike <helen.koike@collabora.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Add the dm-dust target, which simulates the behavior of bad sectors
at arbitrary locations, and the ability to enable the emulation of
the read failures at an arbitrary time.
This target behaves similarly to a linear target. At a given time,
the user can send a message to the target to start failing read
requests on specific blocks. When the failure behavior is enabled,
reads of blocks configured "bad" will fail with EIO.
Writes of blocks configured "bad" will result in the following:
1. Remove the block from the "bad block list".
2. Successfully complete the write.
After this point, the block will successfully contain the written
data, and will service reads and writes normally. This emulates the
behavior of a "remapped sector" on a hard disk drive.
dm-dust provides logging of which blocks have been added or removed
to the "bad block list", as well as logging when a block has been
removed from the bad block list. These messages can be used
alongside the messages from the driver using a dm-dust device to
analyze the driver's behavior when a read fails at a given time.
(This logging can be reduced via a "quiet" mode, if desired.)
NOTE: If the block size is larger than 512 bytes, only the first sector
of each "dust block" is detected. Placing a limiting layer above a dust
target, to limit the minimum I/O size to the dust block size, will
ensure proper emulation of the given large block size.
Signed-off-by: Bryan Gurney <bgurney@redhat.com>
Co-developed-by: Joe Shimkus <jshimkus@redhat.com>
Co-developed-by: John Dorminy <jdorminy@redhat.com>
Co-developed-by: John Pittman <jpittman@redhat.com>
Co-developed-by: Thomas Jaskiewicz <tjaskiew@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
We only have two callers that need the integer loop iterator, and they
can easily maintain it themselves.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Acked-by: David Sterba <dsterba@suse.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Use a variable containing the buffer address instead of the to be
removed integer iterator from bio_for_each_segment_all.
Suggested-by: Matthew Wilcox <willy@infradead.org>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Acked-by: Coly Li <colyli@suse.de>
Reviewed-by: Matthew Wilcox <willy@infradead.org>
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Commit 95f18c9d1310 ("bcache: avoid potential memleak of list of
journal_replay(s) in the CACHE_SYNC branch of run_cache_set") forgets
to remove the original define of LIST_HEAD(journal), which makes
the change no take effect. This patch removes redundant variable
LIST_HEAD(journal) from run_cache_set(), to make Shenghui's fix
working.
Fixes: 95f18c9d1310 ("bcache: avoid potential memleak of list of journal_replay(s) in the CACHE_SYNC branch of run_cache_set")
Reported-by: Juha Aatrokoski <juha.aatrokoski@aalto.fi>
Cc: Shenghui Wang <shhuiw@foxmail.com>
Signed-off-by: Coly Li <colyli@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
Replace the indirection through struct stack_trace with an invocation of
the storage array based interface. This results in less storage space and
indirection.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: David Rientjes <rientjes@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: David Sterba <dsterba@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: linux-btrfs@vger.kernel.org
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: linux-arch@vger.kernel.org
Link: https://lkml.kernel.org/r/20190425094802.533968922@linutronix.de
|
|
Replace the indirection through struct stack_trace with an invocation of
the storage array based interface.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Josh Poimboeuf <jpoimboe@redhat.com>
Cc: Andy Lutomirski <luto@kernel.org>
Cc: dm-devel@redhat.com
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Alexander Potapenko <glider@google.com>
Cc: Alexey Dobriyan <adobriyan@gmail.com>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Christoph Lameter <cl@linux.com>
Cc: Pekka Enberg <penberg@kernel.org>
Cc: linux-mm@kvack.org
Cc: David Rientjes <rientjes@google.com>
Cc: Catalin Marinas <catalin.marinas@arm.com>
Cc: Dmitry Vyukov <dvyukov@google.com>
Cc: Andrey Ryabinin <aryabinin@virtuozzo.com>
Cc: kasan-dev@googlegroups.com
Cc: Mike Rapoport <rppt@linux.vnet.ibm.com>
Cc: Akinobu Mita <akinobu.mita@gmail.com>
Cc: Christoph Hellwig <hch@lst.de>
Cc: iommu@lists.linux-foundation.org
Cc: Robin Murphy <robin.murphy@arm.com>
Cc: Marek Szyprowski <m.szyprowski@samsung.com>
Cc: Johannes Thumshirn <jthumshirn@suse.de>
Cc: David Sterba <dsterba@suse.com>
Cc: Chris Mason <clm@fb.com>
Cc: Josef Bacik <josef@toxicpanda.com>
Cc: linux-btrfs@vger.kernel.org
Cc: Daniel Vetter <daniel@ffwll.ch>
Cc: intel-gfx@lists.freedesktop.org
Cc: Joonas Lahtinen <joonas.lahtinen@linux.intel.com>
Cc: Maarten Lankhorst <maarten.lankhorst@linux.intel.com>
Cc: dri-devel@lists.freedesktop.org
Cc: David Airlie <airlied@linux.ie>
Cc: Jani Nikula <jani.nikula@linux.intel.com>
Cc: Rodrigo Vivi <rodrigo.vivi@intel.com>
Cc: Tom Zanussi <tom.zanussi@linux.intel.com>
Cc: Miroslav Benes <mbenes@suse.cz>
Cc: linux-arch@vger.kernel.org
Link: https://lkml.kernel.org/r/20190425094802.446326191@linutronix.de
|
|
This is a small optimization in writecache_find_entry().
If we go past the condition "if (unlikely(!node))", we can be certain that
there is no entry in the tree that has the block equal to the "block"
variable.
Consequently, we can return the next entry directly, we don't need to go
to the second part of the function that finds the entry with lowest or
highest seq number that matches the "block" variable.
Also, add some whitespace and cleanup needless braces.
Suggested-by: Huaisheng Ye <yehs1@lenovo.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
The stucture member page_offset in writeback_struct never has been
used actually. Remove it.
Signed-off-by: Huaisheng Ye <yehs1@lenovo.com>
Acked-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
When the target line contains an invalid device, delay_ctr() will call
delay_dtr() with NULL workqueue. Attempting to destroy the NULL
workqueue causes a crash.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@vger.kernel.org
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
