| Age | Commit message (Collapse) | Author |
|---|
|
Pull md bugfixes from Neil Brown:
"A few bugfixes for md
Some tagged for -stable"
* tag 'md-3.10-fixes' of git://neil.brown.name/md:
md/raid1,5,10: Disable WRITE SAME until a recovery strategy is in place
md/raid1,raid10: use freeze_array in place of raise_barrier in various places.
md/raid1: consider WRITE as successful only if at least one non-Faulty and non-rebuilding drive completed it.
md: md_stop_writes() should always freeze recovery.
|
|
There are cases where the kernel will believe that the WRITE SAME
command is supported by a block device which does not, in fact,
support WRITE SAME. This currently happens for SATA drivers behind a
SAS controller, but there are probably a hundred other ways that can
happen, including drive firmware bugs.
After receiving an error for WRITE SAME the block layer will retry the
request as a plain write of zeroes, but mdraid will consider the
failure as fatal and consider the drive failed. This has the effect
that all the mirrors containing a specific set of data are each
offlined in very rapid succession resulting in data loss.
However, just bouncing the request back up to the block layer isn't
ideal either, because the whole initial request-retry sequence should
be inside the write bitmap fence, which probably means that md needs
to do its own conversion of WRITE SAME to write zero.
Until the failure scenario has been sorted out, disable WRITE SAME for
raid1, raid5, and raid10.
[neilb: added raid5]
This patch is appropriate for any -stable since 3.7 when write_same
support was added.
Cc: stable@vger.kernel.org
Signed-off-by: H. Peter Anvin <hpa@linux.intel.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Various places in raid1 and raid10 are calling raise_barrier when they
really should call freeze_array.
The former is only intended to be called from "make_request".
The later has extra checks for 'nr_queued' and makes a call to
flush_pending_writes(), so it is safe to call it from within the
management thread.
Using raise_barrier will sometimes deadlock. Using freeze_array
should not.
As 'freeze_array' currently expects one request to be pending (in
handle_read_error - the only previous caller), we need to pass
it the number of pending requests (extra) to ignore.
The deadlock was made particularly noticeable by commits
050b66152f87c7 (raid10) and 6b740b8d79252f13 (raid1) which
appeared in 3.4, so the fix is appropriate for any -stable
kernel since then.
This patch probably won't apply directly to some early kernels and
will need to be applied by hand.
Cc: stable@vger.kernel.org
Reported-by: Alexander Lyakas <alex.bolshoy@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
non-rebuilding drive completed it.
Without that fix, the following scenario could happen:
- RAID1 with drives A and B; drive B was freshly-added and is rebuilding
- Drive A fails
- WRITE request arrives to the array. It is failed by drive A, so
r1_bio is marked as R1BIO_WriteError, but the rebuilding drive B
succeeds in writing it, so the same r1_bio is marked as
R1BIO_Uptodate.
- r1_bio arrives to handle_write_finished, badblocks are disabled,
md_error()->error() does nothing because we don't fail the last drive
of raid1
- raid_end_bio_io() calls call_bio_endio()
- As a result, in call_bio_endio():
if (!test_bit(R1BIO_Uptodate, &r1_bio->state))
clear_bit(BIO_UPTODATE, &bio->bi_flags);
this code doesn't clear the BIO_UPTODATE flag, and the whole master
WRITE succeeds, back to the upper layer.
So we returned success to the upper layer, even though we had written
the data onto the rebuilding drive only. But when we want to read the
data back, we would not read from the rebuilding drive, so this data
is lost.
[neilb - applied identical change to raid10 as well]
This bug can result in lost data, so it is suitable for any
-stable kernel.
Cc: stable@vger.kernel.org
Signed-off-by: Alex Lyakas <alex@zadarastorage.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull block core updates from Jens Axboe:
- Major bit is Kents prep work for immutable bio vecs.
- Stable candidate fix for a scheduling-while-atomic in the queue
bypass operation.
- Fix for the hang on exceeded rq->datalen 32-bit unsigned when merging
discard bios.
- Tejuns changes to convert the writeback thread pool to the generic
workqueue mechanism.
- Runtime PM framework, SCSI patches exists on top of these in James'
tree.
- A few random fixes.
* 'for-3.10/core' of git://git.kernel.dk/linux-block: (40 commits)
relay: move remove_buf_file inside relay_close_buf
partitions/efi.c: replace useless kzalloc's by kmalloc's
fs/block_dev.c: fix iov_shorten() criteria in blkdev_aio_read()
block: fix max discard sectors limit
blkcg: fix "scheduling while atomic" in blk_queue_bypass_start
Documentation: cfq-iosched: update documentation help for cfq tunables
writeback: expose the bdi_wq workqueue
writeback: replace custom worker pool implementation with unbound workqueue
writeback: remove unused bdi_pending_list
aoe: Fix unitialized var usage
bio-integrity: Add explicit field for owner of bip_buf
block: Add an explicit bio flag for bios that own their bvec
block: Add bio_alloc_pages()
block: Convert some code to bio_for_each_segment_all()
block: Add bio_for_each_segment_all()
bounce: Refactor __blk_queue_bounce to not use bi_io_vec
raid1: use bio_copy_data()
pktcdvd: Use bio_reset() in disabled code to kill bi_idx usage
pktcdvd: use bio_copy_data()
block: Add bio_copy_data()
...
|
|
In SSD/hard disk hybid storage, discard request should be ignored for hard
disk. We used to be doing this way, but the unplug path forgets it.
This is suitable for stable tree since v3.6.
Cc: stable@vger.kernel.org
Reported-and-tested-by: Markus <M4rkusXXL@web.de>
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Hi.
Raid1 and raid10 devices leak memory every time they stop.
This is a patch for linux-3.9.0-rc7 to fix this problem.
Thanks,
Hirokazu Takahashi.
Signed-off-by: Hirokazu Takahashi <taka@valinux.co.jp>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When an array is assembled incrementally with mdadm -I -R
and the array switches to "active" mode, md starts a recovery.
If the array was clean, the "fullsync" flag will be 0. Skip
the full recovery in this case, as RAID1 does (the code was
actually copied from the sync_request() method of RAID1).
Signed-off-by: Martin Wilck <mwilck@arcor.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
More prep work for immutable bio vecs, mainly getting rid of references
to bi_idx.
bio_reset was being open coded in a few places. The one in sync_request
was a bit nontrivial to convert, so could use some extra eyeballs.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: NeilBrown <neilb@suse.de>
|
|
Random cleanup - this code was duplicated and it's not really specific
to md.
Also added the ability to return the actual error code.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: NeilBrown <neilb@suse.de>
Acked-by: Tejun Heo <tj@kernel.org>
|
|
For immutable bvecs, all bi_idx usage needs to be audited - so here
we're removing all the unnecessary uses.
Most of these are places where it was being initialized on a bio that
was just allocated, a few others are conversions to standard macros.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
|
|
In the current code bio_split() won't be seeing partially completed bios
so this doesn't change any behaviour, but this makes the code a bit
clearer as to what bio_split() actually requires.
The immediate purpose of the patch is removing unnecessary bi_idx
references, but the end goal is to allow partial completed bios to be
submitted, which along with immutable biovecs enables effecient bio
splitting.
Some of the callers were (double) checking that bios could be split, so
update their checks too.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: Lars Ellenberg <drbd-dev@lists.linbit.com>
CC: Neil Brown <neilb@suse.de>
CC: Martin K. Petersen <martin.petersen@oracle.com>
|
|
Bunch of places in the code weren't using it where they could be -
this'll reduce the size of the patch that puts bi_sector/bi_size/bi_idx
into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: "Ed L. Cashin" <ecashin@coraid.com>
CC: Nick Piggin <npiggin@kernel.dk>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jim Paris <jim@jtan.com>
CC: Geoff Levand <geoff@infradead.org>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ed Cashin <ecashin@coraid.com>
|
|
When raid1/raid10 needs to fix a read error, it first drains
all pending requests by calling freeze_array().
This calls flush_pending_writes() if it needs to sleep,
but some writes may be pending in a per-process plug rather
than in the per-array request queue.
When raid1{,0}_unplug() moves the request from the per-process
plug to the per-array request queue (from which
flush_pending_writes() can flush them), it needs to wake up
freeze_array(), or freeze_array() will never flush them and so
it will block forever.
So add the requires wake_up() calls.
This bug was introduced by commit
f54a9d0e59c4bea3db733921ca9147612a6f292c
for raid1 and a similar commit for RAID10, and so has been present
since linux-3.6. As the bug causes a deadlock I believe this fix is
suitable for -stable.
Cc: stable@vger.kernel.org (3.6.y 3.7.y 3.8.y)
Reported-by: Tregaron Bayly <tbayly@bluehost.com>
Tested-by: Tregaron Bayly <tbayly@bluehost.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID10: Improve redundancy for 'far' and 'offset' algorithms (part 2)
This patch addresses raid arrays that have a number of devices that cannot
be evenly divided by 'far_copies'. (E.g. 5 devices, far_copies = 2) This
case must be handled differently because it causes that last set to be of
a different size than the rest of the sets. We must compute a new modulo
for this last set so that copied chunks are properly wrapped around.
Example use_far_sets=1, far_copies=2, near_copies=1, devices=5:
"far" algorithm
dev1 dev2 dev3 dev4 dev5
==== ==== ==== ==== ====
[ A B ] [ C D E ]
[ G H ] [ I J K ]
...
[ B A ] [ E C D ] --> nominal set of 2 and last set of 3
[ H G ] [ K I J ] []'s show far/offset sets
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The MD RAID10 'far' and 'offset' algorithms make copies of entire stripe
widths - copying them to a different location on the same devices after
shifting the stripe. An example layout of each follows below:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
F A B C D E --> Copy of stripe0, but shifted by 1
L G H I J K
...
"offset" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
F A B C D E --> Copy of stripe0, but shifted by 1
G H I J K L
L G H I J K
...
Redundancy for these algorithms is gained by shifting the copied stripes
one device to the right. This patch proposes that array be divided into
sets of adjacent devices and when the stripe copies are shifted, they wrap
on set boundaries rather than the array size boundary. That is, for the
purposes of shifting, the copies are confined to their sets within the
array. The sets are 'near_copies * far_copies' in size.
The above "far" algorithm example would change to:
"far" algorithm
dev1 dev2 dev3 dev4 dev5 dev6
==== ==== ==== ==== ==== ====
A B C D E F
G H I J K L
...
B A D C F E --> Copy of stripe0, shifted 1, 2-dev sets
H G J I L K Dev sets are 1-2, 3-4, 5-6
...
This has the affect of improving the redundancy of the array. We can
always sustain at least one failure, but sometimes more than one can
be handled. In the first examples, the pairs of devices that CANNOT fail
together are:
(1,2) (2,3) (3,4) (4,5) (5,6) (1, 6) [40% of possible pairs]
In the example where the copies are confined to sets, the pairs of
devices that cannot fail together are:
(1,2) (3,4) (5,6) [20% of possible pairs]
We cannot simply replace the old algorithms, so the 17th bit of the 'layout'
variable is used to indicate whether we use the old or new method of computing
the shift. (This is similar to the way the 16th bit indicates whether the
"far" algorithm or the "offset" algorithm is being used.)
This patch only handles the cases where the number of total raid disks is
a multiple of 'far_copies'. A follow-on patch addresses the condition where
this is not true.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Changes include assigning 'addr' from 's' instead of 'sector' to be
consistent with the way the code does it just a few lines later and
using '%=' vs a conditional and subtraction.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Set mddev queue's max_write_same_sectors to its chunk_sector value (before
disk_stack_limits merges the underlying disk limits.) With that in place,
be sure to handle writes coming down from the block layer that have the
REQ_WRITE_SAME flag set. That flag needs to be copied into any newly cloned
write bio.
Signed-off-by: Joe Lawrence <joe.lawrence@stratus.com>
Acked-by: "Martin K. Petersen" <martin.petersen@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull block driver update from Jens Axboe:
"Now that the core bits are in, here are the driver bits for 3.8. The
branch contains:
- A huge pile of drbd bits that were dumped from the 3.7 merge
window. Following that, it was both made perfectly clear that
there is going to be no more over-the-wall pulls and how the
situation on individual pulls can be improved.
- A few cleanups from Akinobu Mita for drbd and cciss.
- Queue improvement for loop from Lukas. This grew into adding a
generic interface for waiting/checking an even with a specific
lock, allowing this to be pulled out of md and now loop and drbd is
also using it.
- A few fixes for xen back/front block driver from Roger Pau Monne.
- Partition improvements from Stephen Warren, allowing partiion UUID
to be used as an identifier."
* 'for-3.8/drivers' of git://git.kernel.dk/linux-block: (609 commits)
drbd: update Kconfig to match current dependencies
drbd: Fix drbdsetup wait-connect, wait-sync etc... commands
drbd: close race between drbd_set_role and drbd_connect
drbd: respect no-md-barriers setting also when changed online via disk-options
drbd: Remove obsolete check
drbd: fixup after wait_even_lock_irq() addition to generic code
loop: Limit the number of requests in the bio list
wait: add wait_event_lock_irq() interface
xen-blkfront: free allocated page
xen-blkback: move free persistent grants code
block: partition: msdos: provide UUIDs for partitions
init: reduce PARTUUID min length to 1 from 36
block: store partition_meta_info.uuid as a string
cciss: use check_signature()
cciss: cleanup bitops usage
drbd: use copy_highpage
drbd: if the replication link breaks during handshake, keep retrying
drbd: check return of kmalloc in receive_uuids
drbd: Broadcast sync progress no more often than once per second
drbd: don't try to clear bits once the disk has failed
...
|
|
New wait_event{_interruptible}_lock_irq{_cmd} macros added. This commit
moves the private wait_event_lock_irq() macro from MD to regular wait
includes, introduces new macro wait_event_lock_irq_cmd() instead of using
the old method with omitting cmd parameter which is ugly and makes a use
of new macros in the MD. It also introduces the _interruptible_ variant.
The use of new interface is when one have a special lock to protect data
structures used in the condition, or one also needs to invoke "cmd"
before putting it to sleep.
All new macros are expected to be called with the lock taken. The lock
is released before sleep and is reacquired afterwards. We will leave the
macro with the lock held.
Note to DM: IMO this should also fix theoretical race on waitqueue while
using simultaneously wait_event_lock_irq() and wait_event() because of
lack of locking around current state setting and wait queue removal.
Signed-off-by: Lukas Czerner <lczerner@redhat.com>
Cc: Neil Brown <neilb@suse.de>
Cc: David Howells <dhowells@redhat.com>
Cc: Ingo Molnar <mingo@elte.hu>
Cc: Peter Zijlstra <a.p.zijlstra@chello.nl>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
If the raid1 or raid10 unplug function gets called
from a make_request function (which is very possible) when
there are bios on the current->bio_list list, then it will not
be able to successfully call bitmap_unplug() and it could
need to submit more bios and wait for them to complete.
But they won't complete while current->bio_list is non-empty.
So detect that case and handle the unplugging off to another thread
just like we already do when called from within the scheduler.
RAID1 version of bug was introduced in 3.6, so that part of fix is
suitable for 3.6.y. RAID10 part won't apply.
Cc: stable@vger.kernel.org
Reported-by: Torsten Kaiser <just.for.lkml@googlemail.com>
Reported-by: Peter Maloney <peter.maloney@brockmann-consult.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When a write to a replacement device completes, we carefully
and correctly found the rdev that the write actually went to
and the blithely called rdev_dec_pending on the primary rdev,
even if this write was to the replacement.
This means that any writes to an array while a replacement
was ongoing would cause the nr_pending count for the primary
device to go negative, so it could never be removed.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When a replacement operation completes there is a small window
when the original device is marked 'faulty' and the replacement
still looks like a replacement. The faulty should be removed and
the replacement moved in place very quickly, bit it isn't instant.
So the code write out to the array must handle the possibility that
the only working device for some slot in the replacement - but it
doesn't. If the primary device is faulty it just gives up. This
can lead to corruption.
So make the code more robust: if either the primary or the
replacement is present and working, write to them. Only when
neither are present do we give up.
This bug has been present since replacement was introduced in
3.3, so it is suitable for any -stable kernel since then.
Reported-by: "George Spelvin" <linux@horizon.com>
Cc: stable@vger.kernel.org
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Commit 2863b9eb didn't take into account the changes to add TRIM support to
RAID10 (commit 532a2a3fb). That is, when using dm-raid.c to create the
RAID10 arrays, there is no mddev->gendisk or mddev->queue. The code added
to support TRIM simply assumes that mddev->queue is available without
checking. The result is an oops any time dm-raid.c attempts to create a
RAID10 device.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull md updates from NeilBrown:
- "discard" support, some dm-raid improvements and other assorted bits
and pieces.
* tag 'md-3.7' of git://neil.brown.name/md: (29 commits)
md: refine reporting of resync/reshape delays.
md/raid5: be careful not to resize_stripes too big.
md: make sure manual changes to recovery checkpoint are saved.
md/raid10: use correct limit variable
md: writing to sync_action should clear the read-auto state.
Subject: [PATCH] md:change resync_mismatches to atomic64_t to avoid races
md/raid5: make sure to_read and to_write never go negative.
md: When RAID5 is dirty, force reconstruct-write instead of read-modify-write.
md/raid5: protect debug message against NULL derefernce.
md/raid5: add some missing locking in handle_failed_stripe.
MD: raid5 avoid unnecessary zero page for trim
MD: raid5 trim support
md/bitmap:Don't use IS_ERR to judge alloc_page().
md/raid1: Don't release reference to device while handling read error.
raid: replace list_for_each_continue_rcu with new interface
add further __init annotations to crypto/xor.c
DM RAID: Fix for "sync" directive ineffectiveness
DM RAID: Fix comparison of index and quantity for "rebuild" parameter
DM RAID: Add rebuild capability for RAID10
DM RAID: Move 'rebuild' checking code to its own function
...
|
|
Clang complains that we are assigning a variable to itself. This should
be using bad_sectors like the similar earlier check does.
Bug has been present since 3.1-rc1. It is minor but could
conceivably cause corruption or other bad behaviour.
Cc: stable@vger.kernel.org
Signed-off-by: Dan Carpenter <dan.carpenter@oracle.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Now that multiple threads can handle stripes, it is safer to
use an atomic64_t for resync_mismatches, to avoid update races.
Signed-off-by: Jianpeng Ma <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID10: Fix a couple potential kernel panics if RAID10 is used by dm-raid
When device-mapper uses the RAID10 personality through dm-raid.c, there is no
'gendisk' structure in mddev and some sysfs information is also not populated.
This patch avoids touching those non-existent structures.
Signed-off-by: Jonathan Brassow <jbrassow@rehdat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Change the thread parameter, so the thread can carry extra info. Next patch
will use it.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
queuing writes to the md thread means that all requests go through the
one processor which may not be able to keep up with very high request
rates.
So use the plugging infrastructure to submit all requests on unplug.
If a 'schedule' is needed, we fall back on the old approach of handing
the requests to the thread for it to handle.
This is nearly identical to a recent patch which provided similar
functionality to RAID1.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
This makes md raid 10 support TRIM.
If one disk supports discard and another not, or one has
discard_zero_data and another not, there could be inconsistent between
data from such disks. But this should not matter, discarded data is
useless. This will add extra copy in rebuild though.
Signed-off-by: Shaohua Li <shli@fusionio.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The 'enough' function is written to work with 'near' arrays only
in that is implicitly assumes that the offset from one 'group' of
devices to the next is the same as the number of copies.
In reality it is the number of 'near' copies.
So change it to make this number explicit.
This bug makes it possible to run arrays without enough drives
present, which is dangerous.
It is appropriate for an -stable kernel, but will almost certainly
need to be modified for some of them.
Cc: stable@vger.kernel.org
Reported-by: Jakub Husák <jakub@gooseman.cz>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
A 'struct r10bio' has an array of per-copy information at the end.
This array is declared with size [0] and r10bio_pool_alloc allocates
enough extra space to store the per-copy information depending on the
number of copies needed.
So declaring a 'struct r10bio on the stack isn't going to work. It
won't allocate enough space, and memory corruption will ensue.
So in the two places where this is done, declare a sufficiently large
structure and use that instead.
The two call-sites of this bug were introduced in 3.4 and 3.5
so this is suitable for both those kernels. The patch will have to
be modified for 3.4 as it only has one bug.
Cc: stable@vger.kernel.org
Reported-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Tested-by: Ivan Vasilyev <ivan.vasilyev@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Pull block driver changes from Jens Axboe:
- Making the plugging support for drivers a bit more sane from Neil.
This supersedes the plugging change from Shaohua as well.
- The usual round of drbd updates.
- Using a tail add instead of a head add in the request completion for
ndb, making us find the most completed request more quickly.
- A few floppy changes, getting rid of a duplicated flag and also
running the floppy init async (since it takes forever in boot terms)
from Andi.
* 'for-3.6/drivers' of git://git.kernel.dk/linux-block:
floppy: remove duplicated flag FD_RAW_NEED_DISK
blk: pass from_schedule to non-request unplug functions.
block: stack unplug
blk: centralize non-request unplug handling.
md: remove plug_cnt feature of plugging.
block/nbd: micro-optimization in nbd request completion
drbd: announce FLUSH/FUA capability to upper layers
drbd: fix max_bio_size to be unsigned
drbd: flush drbd work queue before invalidate/invalidate remote
drbd: fix potential access after free
drbd: call local-io-error handler early
drbd: do not reset rs_pending_cnt too early
drbd: reset congestion information before reporting it in /proc/drbd
drbd: report congestion if we are waiting for some userland callback
drbd: differentiate between normal and forced detach
drbd: cleanup, remove two unused global flags
floppy: Run floppy initialization asynchronous
|
|
This seemed like a good idea at the time, but after further thought I
cannot see it making a difference other than very occasionally and
testing to try to exercise the case it is most likely to help did not
show any performance difference by removing it.
So remove the counting of active plugs and allow 'pending writes' to
be activated at any time, not just when no plugs are active.
This is only relevant when there is a write-intent bitmap, and the
updating of the bitmap will likely introduce enough delay that
the single-threading of bitmap updates will be enough to collect large
numbers of updates together.
Removing this will make it easier to centralise the unplug code, and
will clear the other for other unplug enhancements which have a
measurable effect.
Signed-off-by: NeilBrown <neilb@suse.de>
Signed-off-by: Jens Axboe <axboe@kernel.dk>
|
|
md/raid10: Export is_congested test.
In similar fashion to commits
11d8a6e3719519fbc0e2c9d61b6fa931b84bf813
1ed7242e591af7e233234d483f12d33818b189d9
we export the RAID10 congestion checking function so that dm-raid.c can
make use of it and make use of the personality. The 'queue' and 'gendisk'
structures will not be available to the MD code when device-mapper sets
up the device, so we conditionalize access to these fields also.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID1/RAID10: Move some macros from .h file to .c file
There are three macros (IO_BLOCKED,IO_MADE_GOOD,BIO_SPECIAL) which are defined
in both raid1.h and raid10.h. They are only used in there respective .c files.
However, if we wish to make RAID10 accessible to the device-mapper RAID
target (dm-raid.c), then we need to move these macros into the .c files where
they are used so that they do not conflict with each other.
The macros from the two files are identical and could be moved into md.h, but
I chose to leave the duplication and have them remain in the personality
files.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID10: Rename the structure 'mirror_info' to 'raid10_info'
The same structure name ('mirror_info') is used by raid1. Each of these
structures are defined in there respective header files. If dm-raid is
to support both RAID1 and RAID10, the header files will be included and
the structure names must not collide.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
MD RAID10: Fix compiler warning.
Initialize variable to prevent compiler warning.
Signed-off-by: Jonathan Brassow <jbrassow@redhat.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
build error introduced by commit b357f04a67c2aeee8
That function doesn't get extra args until a later patch. Bother.
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Reported-by: Simon Kirby <sim@hostway.ca>
Reported-by: Tobias Klausmann <tobias.johannes.klausmann@mni.thm.de>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The value returned by "mddev_check_plug" is only valid until the
next 'schedule' as that will unplug things. This could happen at any
call to mempool_alloc.
So just calling mddev_check_plug at the start doesn't really make
sense.
So call it just before, or just after, queuing things for the thread.
As the action that happens at unplug is to wake the thread, this makes
lots of sense.
If we cannot add a plug (which requires a small GFP_ATOMIC alloc) we
wake thread immediately.
RAID5 is a bit different. Requests are queued for the thread and the
thread is woken by release_stripe. So we don't need to wake the
thread on failure.
However the thread doesn't perform certain actions when there is any
active plug, so it is important to install a plug before waking the
thread. So for RAID5 we install the plug *before* queuing the request
and waking the thread.
Without this patch it is possible for raid1 or raid10 to queue a
request without then waking the thread, resulting in the array locking
up.
Also change raid10 to only flush_pending_write when there are not
active plugs, just like raid1.
This patch is suitable for 3.0 or later. I plan to submit it to
-stable, but I'll like to let it spend a few weeks in mainline
first to be sure it is completely safe.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Having the 'name' arg optional and defaulting to the current
personality name is no necessary and leads to errors, as when
changing the level of an array we can end up using the
name of the old level instead of the new one.
So make it non-optional and always explicitly pass the name
of the level that the array will be.
Reported-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
commit 58c54fcca3bac5bf9290cfed31c76e4c4bfbabaf
md/raid10: handle further errors during fix_read_error better.
in 3.1 added "r10_sync_page_io" which takes an IO size in sectors.
But we were passing the IO size in bytes!!!
This resulting in bio_add_page failing, and empty request being sent
down, and a consequent BUG_ON in scsi_lib.
[fix missing space in error message at same time]
This fix is suitable for 3.1.y and later.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a RAID10 has an odd number of chunks - as might happen when there
are an odd number of devices - the last chunk has no pair and so is
not mirrored. We don't store data there, but when recovering the last
device in an array we retry to recover that last chunk from a
non-existent location. This results in an error, and the recovery
aborts.
When we get to that last chunk we should just stop - there is nothing
more to do anyway.
This bug has been present since the introduction of RAID10, so the
patch is appropriate for any -stable kernel.
Cc: stable@vger.kernel.org
Reported-by: Christian Balzer <chibi@gol.com>
Tested-by: Christian Balzer <chibi@gol.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
The new merge_bvec_fn which calls the corresponding function
in subsidiary devices requires that mddev->merge_check_needed
be set if any child has a merge_bvec_fn.
However were were only setting that when a device was hot-added,
not when a device was present from the start.
This bug was introduced in 3.4 so patch is suitable for 3.4.y
kernels. However that are conflicts in raid10.c so a separate
patch will be needed for 3.4.y.
Cc: stable@vger.kernel.org
Reported-by: Sebastian Riemer <sebastian.riemer@profitbricks.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
When a reshape which reduced the number of devices finishes
we must remove the extra devices.
So ensure that raid10_remove_disk won't try to keep them, and
have raid10_finish_reshape clear the 'in_sync' flag. Then
remove_and_add_spares will be able to remove them.
Reported-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If a reshape changes the size of the array, then we can now
update the bitmap to suit - so do so.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
Now that bitmaps can be resized, we can allow an array to be resized
while the bitmap is present.
This only covers resizing that involves changing the effective size
of member devices, not resizing that changes the number of devices.
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
If the allocation of rep1_bio fails, we currently don't free the 'bio'
of the same dev.
Reported by kmemleak.
Signed-off-by: majianpeng <majianpeng@gmail.com>
Signed-off-by: NeilBrown <neilb@suse.de>
|
|
A 'near' or 'offset' lay RAID10 array can be reshaped to a different
'near' or 'offset' layout, a different chunk size, and a different
number of devices.
However the number of copies cannot change.
Unlike RAID5/6, we do not support having user-space backup data that
is being relocated during a 'critical section'. Rather, the
data_offset of each device must change so that when writing any block
to a new location, it will not over-write any data that is still
'live'.
This means that RAID10 reshape is not supportable on v0.90 metadata.
The different between the old data_offset and the new_offset must be
at least the larger of the chunksize multiplied by offset copies of
each of the old and new layout. (for 'near' mode, offset_copies == 1).
A larger difference of around 64M seems useful for in-place reshapes
as more data can be moved between metadata updates.
Very large differences (e.g. 512M) seem to slow the process down due
to lots of long seeks (on oldish consumer graded devices at least).
Metadata needs to be updated whenever the place we are about to write
to is considered - by the current metadata - to still contain data in
the old layout.
[unbalanced locking fix from Dan Carpenter <dan.carpenter@oracle.com>]
Signed-off-by: NeilBrown <neilb@suse.de>
|
