| Age | Commit message (Collapse) | Author |
|---|
|
When any leg(s) have failed, any read will cause a new operational
default leg to be selected and the read is resubmitted to it. If that
new default leg fails the read too, no other still accessible legs are
used to resubmit the read again -- thus failing the io.
Fix by allowing the read to get resubmitted until all operational legs
have been exhausted. Also, remove any details.bi_dev use as a flag.
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
If a default leg has failed, any read will cause a new operational
default leg to be selected and the read is resubmitted. But until now
the read will return failure even though it was successful due to
resubmission. The reason for this is bio->bi_error was not being
cleared before resubmitting the bio.
Fix by clearing bio->bi_error before resubmission.
Fixes: 4246a0b63bd8 ("block: add a bi_error field to struct bio")
Cc: stable@vger.kernel.org # 4.3+
Signed-off-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Since commit 63a4cc24867d, bio->bi_rw contains flags in the lower
portion and the op code in the higher portions. This means that
old code that relies on manually setting bi_rw is most likely
going to be broken. Instead of letting that brokeness linger,
rename the member, to force old and out-of-tree code to break
at compile time instead of at runtime.
No intended functional changes in this commit.
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
These two are confusing leftover of the old world order, combining
values of the REQ_OP_ and REQ_ namespaces. For callers that don't
special case we mostly just replace bi_rw with bio_data_dir or
op_is_write, except for the few cases where a switch over the REQ_OP_
values makes more sense. Any check for READA is replaced with an
explicit check for REQ_RAHEAD. Also remove the READA alias for
REQ_RAHEAD.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Johannes Thumshirn <jthumshirn@suse.de>
Reviewed-by: Mike Christie <mchristi@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
To avoid confusion between REQ_OP_FLUSH, which is handled by
request_fn drivers, and upper layers requesting the block layer
perform a flush sequence along with possibly a WRITE, this patch
renames REQ_FLUSH to REQ_PREFLUSH.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Separate the op from the rq_flag_bits and have dm
set/get the bio using bio_set_op_attrs/bio_op.
Signed-off-by: Mike Christie <mchristi@redhat.com>
Reviewed-by: Hannes Reinecke <hare@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Request-based DM will also make use of per_bio_data_size.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm
Pull device mapper update from Mike Snitzer:
- a couple small cleanups in dm-cache, dm-verity, persistent-data's
dm-btree, and DM core.
- a 4.1-stable fix for dm-cache that fixes the leaking of deferred bio
prison cells
- a 4.2-stable fix that adds feature reporting for the dm-stats
features added in 4.2
- improve DM-snapshot to not invalidate the on-disk snapshot if
snapshot device write overflow occurs; but a write overflow triggered
through the origin device will still invalidate the snapshot.
- optimize DM-thinp's async discard submission a bit now that late bio
splitting has been included in block core.
- switch DM-cache's SMQ policy lock from using a mutex to a spinlock;
improves performance on very low latency devices (eg. NVMe SSD).
- document DM RAID 4/5/6's discard support
[ I did not pull the slab changes, which weren't appropriate for this
tree, and weren't obviously the right thing to do anyway. At the very
least they need some discussion and explanation before getting merged.
Because not pulling the actual tagged commit but doing a partial pull
instead, this merge commit thus also obviously is missing the git
signature from the original tag ]
* tag 'dm-4.3-changes' of git://git.kernel.org/pub/scm/linux/kernel/git/device-mapper/linux-dm:
dm cache: fix use after freeing migrations
dm cache: small cleanups related to deferred prison cell cleanup
dm cache: fix leaking of deferred bio prison cells
dm raid: document RAID 4/5/6 discard support
dm stats: report precise_timestamps and histogram in @stats_list output
dm thin: optimize async discard submission
dm snapshot: don't invalidate on-disk image on snapshot write overflow
dm: remove unlikely() before IS_ERR()
dm: do not override error code returned from dm_get_device()
dm: test return value for DM_MAPIO_SUBMITTED
dm verity: remove unused mempool
dm cache: move wake_waker() from free_migrations() to where it is needed
dm btree remove: remove unused function get_nr_entries()
dm btree: remove unused "dm_block_t root" parameter in btree_split_sibling()
dm cache policy smq: change the mutex to a spinlock
|
|
Some of the device mapper targets override the error code returned by
dm_get_device() and return either -EINVAL or -ENXIO. There is nothing
gained by this override. It is better to propagate the returned error
code unchanged to caller.
This work was motivated by hitting an issue where the underlying device
was busy but -EINVAL was being returned. After this change we get
-EBUSY instead and it is easier to figure out the problem.
Signed-off-by: Vivek Goyal <vgoyal@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Currently we have two different ways to signal an I/O error on a BIO:
(1) by clearing the BIO_UPTODATE flag
(2) by returning a Linux errno value to the bi_end_io callback
The first one has the drawback of only communicating a single possible
error (-EIO), and the second one has the drawback of not beeing persistent
when bios are queued up, and are not passed along from child to parent
bio in the ever more popular chaining scenario. Having both mechanisms
available has the additional drawback of utterly confusing driver authors
and introducing bugs where various I/O submitters only deal with one of
them, and the others have to add boilerplate code to deal with both kinds
of error returns.
So add a new bi_error field to store an errno value directly in struct
bio and remove the existing mechanisms to clean all this up.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Hannes Reinecke <hare@suse.de>
Reviewed-by: NeilBrown <neilb@suse.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Currently if there is a leg failure, the bio will be put into the hold
list until userspace does a remove/replace on the leg. Doing so in a
cluster config (clvmd) is problematic because there may be a temporary
path failure that results in cluster raid1 remove/replace. Such
recovery takes a long time due to a full resync.
Update dm-raid1 to optionally ignore these failures so bios continue
being issued without interrupton. To enable this feature userspace
must pass "keep_log" when creating the dm-raid1 device.
Signed-off-by: Lidong Zhong <lzhong@suse.com>
Tested-by: Liuhua Wang <lwang@suse.com>
Acked-by: Heinz Mauelshagen <heinzm@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Commit c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for
non-chains") regressed all existing callers that followed this pattern:
1) saving a bio's original bi_end_io
2) wiring up an intermediate bi_end_io
3) restoring the original bi_end_io from intermediate bi_end_io
4) calling bio_endio() to execute the restored original bi_end_io
The regression was due to BIO_CHAIN only ever getting set if
bio_inc_remaining() is called. For the above pattern it isn't set until
step 3 above (step 2 would've needed to establish BIO_CHAIN). As such
the first bio_endio(), in step 2 above, never decremented __bi_remaining
before calling the intermediate bi_end_io -- leaving __bi_remaining with
the value 1 instead of 0. When bio_inc_remaining() occurred during step
3 it brought it to a value of 2. When the second bio_endio() was
called, in step 4 above, it should've called the original bi_end_io but
it didn't because there was an extra reference that wasn't dropped (due
to atomic operations being optimized away since BIO_CHAIN wasn't set
upfront).
Fix this issue by removing the __bi_remaining management complexity for
all callers that use the above pattern -- bio_chain() is the only
interface that _needs_ to be concerned with __bi_remaining. For the
above pattern callers just expect the bi_end_io they set to get called!
Remove bio_endio_nodec() and also remove all bio_inc_remaining() calls
that aren't associated with the bio_chain() interface.
Also, the bio_inc_remaining() interface has been moved local to bio.c.
Fixes: c4cf5261 ("bio: skip atomic inc/dec of ->bi_remaining for non-chains")
Reviewed-by: Christoph Hellwig <hch@lst.de>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
Struct bio has an atomic ref count for chained bio's, and we use this
to know when to end IO on the bio. However, most bio's are not chained,
so we don't need to always introduce this atomic operation as part of
ending IO.
Add a helper to elevate the bi_remaining count, and flag the bio as
now actually needing the decrement at end_io time. Rename the field
to __bi_remaining to catch any current users of this doing the
incrementing manually.
For high IOPS workloads, this reduces the overhead of bio_endio()
substantially.
Tested-by: Robert Elliott <elliott@hp.com>
Acked-by: Kent Overstreet <kent.overstreet@gmail.com>
Reviewed-by: Jan Kara <jack@suse.cz>
Signed-off-by: Jens Axboe <axboe@fb.com>
|
|
It may be possible that a device claims discard support but it rejects
discards with -EOPNOTSUPP. It happens when using loopback on ext2/ext3
filesystem driven by the ext4 driver. It may also happen if the
underlying devices are moved from one disk on another.
If discard error happens, we reject the bio with -EOPNOTSUPP, but we do
not degrade the array.
This patch fixes failed test shell/lvconvert-repair-transient.sh in the
lvm2 testsuite if the testsuite is extracted on an ext2 or ext3
filesystem and it is being driven by the ext4 driver.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Cc: stable@vger.kernel.org
|
|
When restoring bi_end_io, increase bi_remaining before retrying the bio
to avoid BUG_ON(atomic_read(&bio->bi_remaining) <= 0) in bio_endio().
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
|
|
Now that we've got a mechanism for immutable biovecs -
bi_iter.bi_bvec_done - we need to convert drivers to use primitives that
respect it instead of using the bvec array directly.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: NeilBrown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: dm-devel@redhat.com
|
|
Immutable biovecs are going to require an explicit iterator. To
implement immutable bvecs, a later patch is going to add a bi_bvec_done
member to this struct; for now, this patch effectively just renames
things.
Signed-off-by: Kent Overstreet <kmo@daterainc.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Geert Uytterhoeven <geert@linux-m68k.org>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: "Ed L. Cashin" <ecashin@coraid.com>
Cc: Nick Piggin <npiggin@kernel.dk>
Cc: Lars Ellenberg <drbd-dev@lists.linbit.com>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Matthew Wilcox <willy@linux.intel.com>
Cc: Geoff Levand <geoff@infradead.org>
Cc: Yehuda Sadeh <yehuda@inktank.com>
Cc: Sage Weil <sage@inktank.com>
Cc: Alex Elder <elder@inktank.com>
Cc: ceph-devel@vger.kernel.org
Cc: Joshua Morris <josh.h.morris@us.ibm.com>
Cc: Philip Kelleher <pjk1939@linux.vnet.ibm.com>
Cc: Rusty Russell <rusty@rustcorp.com.au>
Cc: "Michael S. Tsirkin" <mst@redhat.com>
Cc: Konrad Rzeszutek Wilk <konrad.wilk@oracle.com>
Cc: Jeremy Fitzhardinge <jeremy@goop.org>
Cc: Neil Brown <neilb@suse.de>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mike Snitzer <snitzer@redhat.com>
Cc: dm-devel@redhat.com
Cc: Martin Schwidefsky <schwidefsky@de.ibm.com>
Cc: Heiko Carstens <heiko.carstens@de.ibm.com>
Cc: linux390@de.ibm.com
Cc: Boaz Harrosh <bharrosh@panasas.com>
Cc: Benny Halevy <bhalevy@tonian.com>
Cc: "James E.J. Bottomley" <JBottomley@parallels.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: "Nicholas A. Bellinger" <nab@linux-iscsi.org>
Cc: Alexander Viro <viro@zeniv.linux.org.uk>
Cc: Chris Mason <chris.mason@fusionio.com>
Cc: "Theodore Ts'o" <tytso@mit.edu>
Cc: Andreas Dilger <adilger.kernel@dilger.ca>
Cc: Jaegeuk Kim <jaegeuk.kim@samsung.com>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Dave Kleikamp <shaggy@kernel.org>
Cc: Joern Engel <joern@logfs.org>
Cc: Prasad Joshi <prasadjoshi.linux@gmail.com>
Cc: Trond Myklebust <Trond.Myklebust@netapp.com>
Cc: KONISHI Ryusuke <konishi.ryusuke@lab.ntt.co.jp>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Joel Becker <jlbec@evilplan.org>
Cc: Ben Myers <bpm@sgi.com>
Cc: xfs@oss.sgi.com
Cc: Steven Rostedt <rostedt@goodmis.org>
Cc: Frederic Weisbecker <fweisbec@gmail.com>
Cc: Ingo Molnar <mingo@redhat.com>
Cc: Len Brown <len.brown@intel.com>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: "Rafael J. Wysocki" <rjw@sisk.pl>
Cc: Herton Ronaldo Krzesinski <herton.krzesinski@canonical.com>
Cc: Ben Hutchings <ben@decadent.org.uk>
Cc: Andrew Morton <akpm@linux-foundation.org>
Cc: Guo Chao <yan@linux.vnet.ibm.com>
Cc: Tejun Heo <tj@kernel.org>
Cc: Asai Thambi S P <asamymuthupa@micron.com>
Cc: Selvan Mani <smani@micron.com>
Cc: Sam Bradshaw <sbradshaw@micron.com>
Cc: Wei Yongjun <yongjun_wei@trendmicro.com.cn>
Cc: "Roger Pau Monné" <roger.pau@citrix.com>
Cc: Jan Beulich <jbeulich@suse.com>
Cc: Stefano Stabellini <stefano.stabellini@eu.citrix.com>
Cc: Ian Campbell <Ian.Campbell@citrix.com>
Cc: Sebastian Ott <sebott@linux.vnet.ibm.com>
Cc: Christian Borntraeger <borntraeger@de.ibm.com>
Cc: Minchan Kim <minchan@kernel.org>
Cc: Jiang Liu <jiang.liu@huawei.com>
Cc: Nitin Gupta <ngupta@vflare.org>
Cc: Jerome Marchand <jmarchand@redhat.com>
Cc: Joe Perches <joe@perches.com>
Cc: Peng Tao <tao.peng@emc.com>
Cc: Andy Adamson <andros@netapp.com>
Cc: fanchaoting <fanchaoting@cn.fujitsu.com>
Cc: Jie Liu <jeff.liu@oracle.com>
Cc: Sunil Mushran <sunil.mushran@gmail.com>
Cc: "Martin K. Petersen" <martin.petersen@oracle.com>
Cc: Namjae Jeon <namjae.jeon@samsung.com>
Cc: Pankaj Kumar <pankaj.km@samsung.com>
Cc: Dan Magenheimer <dan.magenheimer@oracle.com>
Cc: Mel Gorman <mgorman@suse.de>6
|
|
dbf2576e37 ("workqueue: make all workqueues non-reentrant") made
WQ_NON_REENTRANT no-op and the flag is going away. Remove its usages.
This patch doesn't introduce any behavior changes.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Acked-by: Joe Thornber <ejt@redhat.com>
|
|
Bunch of places in the code weren't using it where they could be -
this'll reduce the size of the patch that puts bi_sector/bi_size/bi_idx
into a struct bvec_iter.
Signed-off-by: Kent Overstreet <koverstreet@google.com>
CC: Jens Axboe <axboe@kernel.dk>
CC: "Ed L. Cashin" <ecashin@coraid.com>
CC: Nick Piggin <npiggin@kernel.dk>
CC: Jiri Kosina <jkosina@suse.cz>
CC: Jim Paris <jim@jtan.com>
CC: Geoff Levand <geoff@infradead.org>
CC: Alasdair Kergon <agk@redhat.com>
CC: dm-devel@redhat.com
CC: Neil Brown <neilb@suse.de>
CC: Steven Rostedt <rostedt@goodmis.org>
Acked-by: Ed Cashin <ecashin@coraid.com>
|
|
This patch allows the administrator to reduce the rate at which kcopyd
issues I/O.
Each module that uses kcopyd acquires a throttle parameter that can be
set in /sys/module/*/parameters.
We maintain a history of kcopyd usage by each module in the variables
io_period and total_period in struct dm_kcopyd_throttle. The actual
kcopyd activity is calculated as a percentage of time equal to
"(100 * io_period / total_period)". This is compared with the user-defined
throttle percentage threshold and if it is exceeded, we sleep.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use 'bio' in the name of variables and functions that deal with
bios rather than 'request' to avoid confusion with the normal
block layer use of 'request'.
No functional changes.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Avoid returning a truncated table or status string instead of setting
the DM_BUFFER_FULL_FLAG when the last target of a table fills the
buffer.
When processing a table or status request, the function retrieve_status
calls ti->type->status. If ti->type->status returns non-zero,
retrieve_status assumes that the buffer overflowed and sets
DM_BUFFER_FULL_FLAG.
However, targets don't return non-zero values from their status method
on overflow. Most targets returns always zero.
If a buffer overflow happens in a target that is not the last in the
table, it gets noticed during the next iteration of the loop in
retrieve_status; but if a buffer overflow happens in the last target, it
goes unnoticed and erroneously truncated data is returned.
In the current code, the targets behave in the following way:
* dm-crypt returns -ENOMEM if there is not enough space to store the
key, but it returns 0 on all other overflows.
* dm-thin returns errors from the status method if a disk error happened.
This is incorrect because retrieve_status doesn't check the error
code, it assumes that all non-zero values mean buffer overflow.
* all the other targets always return 0.
This patch changes the ti->type->status function to return void (because
most targets don't use the return code). Overflow is detected in
retrieve_status: if the status method fills up the remaining space
completely, it is assumed that buffer overflow happened.
Cc: stable@vger.kernel.org
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch removes map_info from bio-based device mapper targets.
map_info is still used for request-based targets.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Don't use map_info any more in dm-raid1.
map_info was used for writes to hold the region number. For this purpose
we add a new field dm_bio_details to dm_raid1_bio_record.
map_info was used for reads to hold a pointer to dm_raid1_bio_record (if
the pointer was non-NULL, bio details were saved; if the pointer was
NULL, bio details were not saved). We use
dm_raid1_bio_record.details->bi_bdev for this purpose. If bi_bdev is
NULL, details were not saved, if bi_bdev is non-NULL, details were
saved.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Rename struct read_record to bio_record in dm-raid1.
In the following patch, the structure will be used for both read and
write bios, so rename it.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Replace read_record_pool with per_bio_data in dm-raid1.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use a defined macro DM_ENDIO_INCOMPLETE instead of a numeric constant.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
mempool_alloc can't fail if __GFP_WAIT is specified, so the condition
that tests if read_record is non-NULL is always true.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
flush[_delayed]_work_sync() are now spurious. Mark them deprecated
and convert all users to flush[_delayed]_work().
If you're cc'd and wondering what's going on: Now all workqueues are
non-reentrant and the regular flushes guarantee that the work item is
not pending or running on any CPU on return, so there's no reason to
use the sync flushes at all and they're going away.
This patch doesn't make any functional difference.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: Russell King <linux@arm.linux.org.uk>
Cc: Paul Mundt <lethal@linux-sh.org>
Cc: Ian Campbell <ian.campbell@citrix.com>
Cc: Jens Axboe <axboe@kernel.dk>
Cc: Mattia Dongili <malattia@linux.it>
Cc: Kent Yoder <key@linux.vnet.ibm.com>
Cc: David Airlie <airlied@linux.ie>
Cc: Jiri Kosina <jkosina@suse.cz>
Cc: Karsten Keil <isdn@linux-pingi.de>
Cc: Bryan Wu <bryan.wu@canonical.com>
Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Alasdair Kergon <agk@redhat.com>
Cc: Mauro Carvalho Chehab <mchehab@infradead.org>
Cc: Florian Tobias Schandinat <FlorianSchandinat@gmx.de>
Cc: David Woodhouse <dwmw2@infradead.org>
Cc: "David S. Miller" <davem@davemloft.net>
Cc: linux-wireless@vger.kernel.org
Cc: Anton Vorontsov <cbou@mail.ru>
Cc: Sangbeom Kim <sbkim73@samsung.com>
Cc: "James E.J. Bottomley" <James.Bottomley@HansenPartnership.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Eric Van Hensbergen <ericvh@gmail.com>
Cc: Takashi Iwai <tiwai@suse.de>
Cc: Steven Whitehouse <swhiteho@redhat.com>
Cc: Petr Vandrovec <petr@vandrovec.name>
Cc: Mark Fasheh <mfasheh@suse.com>
Cc: Christoph Hellwig <hch@infradead.org>
Cc: Avi Kivity <avi@redhat.com>
|
|
Commit outstanding metadata before returning the status for a dm thin
pool so that the numbers reported are as up-to-date as possible.
The commit is not performed if the device is suspended or if
the DM_NOFLUSH_FLAG is supplied by userspace and passed to the target
through a new 'status_flags' parameter in the target's dm_status_fn.
The userspace dmsetup tool will support the --noflush flag with the
'dmsetup status' and 'dmsetup wait' commands from version 1.02.76
onwards.
Tested-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Use boolean bit fields for flags in struct dm_target.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Remove the restriction that limits a target's specified maximum incoming
I/O size to be a power of 2.
Rename this setting from 'split_io' to the less-ambiguous 'max_io_len'.
Change it from sector_t to uint32_t, which is plenty big enough, and
introduce a wrapper function dm_set_target_max_io_len() to set it.
Use sector_div() to process it now that it is not necessarily a power of 2.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
We can't guarantee that REQ_DISCARD on dm-mirror zeroes the data even if
the underlying disks support zero on discard. So this patch sets
ti->discard_zeroes_data_unsupported.
For example, if the mirror is in the process of resynchronizing, it may
happen that kcopyd reads a piece of data, then discard is sent on the
same area and then kcopyd writes the piece of data to another leg.
Consequently, the data is not zeroed.
The flag was made available by commit 983c7db347db8ce2d8453fd1d89b7a4bb6920d56
(dm crypt: always disable discard_zeroes_data).
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch fixes a crash when a discard request is sent during mirror
recovery.
Firstly, some background. Generally, the following sequence happens during
mirror synchronization:
- function do_recovery is called
- do_recovery calls dm_rh_recovery_prepare
- dm_rh_recovery_prepare uses a semaphore to limit the number
simultaneously recovered regions (by default the semaphore value is 1,
so only one region at a time is recovered)
- dm_rh_recovery_prepare calls __rh_recovery_prepare,
__rh_recovery_prepare asks the log driver for the next region to
recover. Then, it sets the region state to DM_RH_RECOVERING. If there
are no pending I/Os on this region, the region is added to
quiesced_regions list. If there are pending I/Os, the region is not
added to any list. It is added to the quiesced_regions list later (by
dm_rh_dec function) when all I/Os finish.
- when the region is on quiesced_regions list, there are no I/Os in
flight on this region. The region is popped from the list in
dm_rh_recovery_start function. Then, a kcopyd job is started in the
recover function.
- when the kcopyd job finishes, recovery_complete is called. It calls
dm_rh_recovery_end. dm_rh_recovery_end adds the region to
recovered_regions or failed_recovered_regions list (depending on
whether the copy operation was successful or not).
The above mechanism assumes that if the region is in DM_RH_RECOVERING
state, no new I/Os are started on this region. When I/O is started,
dm_rh_inc_pending is called, which increases reg->pending count. When
I/O is finished, dm_rh_dec is called. It decreases reg->pending count.
If the count is zero and the region was in DM_RH_RECOVERING state,
dm_rh_dec adds it to the quiesced_regions list.
Consequently, if we call dm_rh_inc_pending/dm_rh_dec while the region is
in DM_RH_RECOVERING state, it could be added to quiesced_regions list
multiple times or it could be added to this list when kcopyd is copying
data (it is assumed that the region is not on any list while kcopyd does
its jobs). This results in memory corruption and crash.
There already exist bypasses for REQ_FLUSH requests: REQ_FLUSH requests
do not belong to any region, so they are always added to the sync list
in do_writes. dm_rh_inc_pending does not increase count for REQ_FLUSH
requests. In mirror_end_io, dm_rh_dec is never called for REQ_FLUSH
requests. These bypasses avoid the crash possibility described above.
These bypasses were improperly implemented for REQ_DISCARD when
the mirror target gained discard support in commit
5fc2ffeabb9ee0fc0e71ff16b49f34f0ed3d05b4 (dm raid1: support discard).
In do_writes, REQ_DISCARD requests is always added to the sync queue and
immediately dispatched (even if the region is in DM_RH_RECOVERING). However,
dm_rh_inc and dm_rh_dec is called for REQ_DISCARD resusts. So it violates the
rule that no I/Os are started on DM_RH_RECOVERING regions, and causes the list
corruption described above.
This patch changes it so that REQ_DISCARD requests follow the same path
as REQ_FLUSH. This avoids the crash.
Reference: https://bugzilla.redhat.com/837607
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Cc: stable@kernel.org
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Device mapper uses sscanf to convert arguments to numbers. The problem is that
the way we use it ignores additional unmatched characters in the scanned string.
For example, this `if (sscanf(string, "%d", &number) == 1)' will match a number,
but also it will match number with some garbage appended, like "123abc".
As a result, device mapper accepts garbage after some numbers. For example
the command `dmsetup create vg1-new --table "0 16384 linear 254:1bla 34816bla"'
will pass without an error.
This patch fixes all sscanf uses in device mapper. It appends "%c" with
a pointer to a dummy character variable to every sscanf statement.
The construct `if (sscanf(string, "%d%c", &number, &dummy) == 1)' succeeds
only if string is a null-terminated number (optionally preceded by some
whitespace characters). If there is some character appended after the number,
sscanf matches "%c", writes the character to the dummy variable and returns 2.
We check the return value for 1 and consequently reject numbers with some
garbage appended.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Acked-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Return client directly from dm_kcopyd_client_create, not through a
parameter, making it consistent with dm_io_client_create.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Reserve just the minimum of pages needed to process one job.
Because we allocate pages from page allocator, we don't need to reserve
a large number of pages. The maximum job size is SUB_JOB_SIZE and we
calculate the number of reserved pages based on this.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Replace the arbitrary calculation of an initial io struct mempool size
with a constant.
The code calculated the number of reserved structures based on the request
size and used a "magic" multiplication constant of 4. This patch changes
it to reserve a fixed number - itself still chosen quite arbitrarily.
Further testing might show if there is a better number to choose.
Note that if there is no memory pressure, we can still allocate an
arbitrary number of "struct io" structures. One structure is enough to
process the whole request.
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Code has been converted over to the new explicit on-stack plugging,
and delay users have been converted to use the new API for that.
So lets kill off the old plugging along with aops->sync_page().
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
kmirrord_wq, kcopyd_work and md->wq are created per dm instance and
serve only a single work item from the dm instance, so non-reentrant
workqueues would provide the same ordering guarantees as ordered ones
while allowing CPU affinity and use of the workqueues for other
purposes. Switch them to non-reentrant workqueues.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Convert all create[_singlethread]_work() users to the new
alloc[_ordered]_workqueue(). This conversion is mechanical and
doesn't introduce any behavior change.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
flush_scheduled_work() is being deprecated. Flush the used work
directly instead. In all dm targets, the only work which uses
system_wq is ->trigger_event.
Signed-off-by: Tejun Heo <tj@kernel.org>
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Enable discard support in the DM mirror target.
Also change an existing use of 'bvec' to 'addr' in the union.
Signed-off-by: Mike Snitzer <snitzer@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
This patch converts bio-based dm to support REQ_FLUSH/FUA instead of
now deprecated REQ_HARDBARRIER.
* -EOPNOTSUPP handling logic dropped.
* Preflush is handled as before but postflush is dropped and replaced
with passing down REQ_FUA to member request_queues. This replaces
one array wide cache flush w/ member specific FUA writes.
* __split_and_process_bio() now calls __clone_and_map_flush() directly
for flushes and guarantees all FLUSH bio's going to targets are zero
` length.
* It's now guaranteed that all FLUSH bio's which are passed onto dm
targets are zero length. bio_empty_barrier() tests are replaced
with REQ_FLUSH tests.
* Empty WRITE_BARRIERs are replaced with WRITE_FLUSHes.
* Dropped unlikely() around REQ_FLUSH tests. Flushes are not unlikely
enough to be marked with unlikely().
* Block layer now filters out REQ_FLUSH/FUA bio's if the request_queue
doesn't support cache flushing. Advertise REQ_FLUSH | REQ_FUA
capability.
* Request based dm isn't converted yet. dm_init_request_based_queue()
resets flush support to 0 for now. To avoid disturbing request
based dm code, dm->flush_error is added for bio based dm while
requested based dm continues to use dm->barrier_error.
Lightly tested linear, stripe, raid1, snap and crypt targets. Please
proceed with caution as I'm not familiar with the code base.
Signed-off-by: Tejun Heo <tj@kernel.org>
Cc: dm-devel@redhat.com
Cc: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
Use new dm_target_offset() macro to avoid most references to ti->begin
in dm targets.
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
Remove the current bio flags and reuse the request flags for the bio, too.
This allows to more easily trace the type of I/O from the filesystem
down to the block driver. There were two flags in the bio that were
missing in the requests: BIO_RW_UNPLUG and BIO_RW_AHEAD. Also I've
renamed two request flags that had a superflous RW in them.
Note that the flags are in bio.h despite having the REQ_ name - as
blkdev.h includes bio.h that is the only way to go for now.
Signed-off-by: Christoph Hellwig <hch@lst.de>
Signed-off-by: Jens Axboe <jaxboe@fusionio.com>
|
|
To prevent deadlock, bios in the hold list should be flushed before
dm_rh_stop_recovery() is called in mirror_suspend().
The recovery can't start because there are pending bios and therefore
dm_rh_stop_recovery deadlocks.
When there are pending bios in the hold list, the recovery waits for
the completion of the bios after recovery_count is acquired.
The recovery_count is released when the recovery finished, however,
the bios in the hold list are processed after dm_rh_stop_recovery() in
mirror_presuspend(). dm_rh_stop_recovery() also acquires recovery_count,
then deadlock occurs.
Signed-off-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
Reviewed-by: Mikulas Patocka <mpatocka@redhat.com>
|
|
Remove unused parameters(start and len) of dm_get_device()
and fix the callers.
Signed-off-by: Nikanth Karthikesan <knikanth@suse.de>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
If all mirror legs fail, always return an error instead of holding the
bio, even if the handle_errors option was set. At present it is the
responsibility of the driver underneath us to deal with retries,
multipath etc.
The patch adds the bio to the failures list instead of holding it
directly. do_failures tests first if all legs failed and, if so,
returns the bio with -EIO. If any leg is still alive and handle_errors
is set, do_failures calls hold_bio.
Reviewed-by: Takahiro Yasui <tyasui@redhat.com>
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
|
If the mirror log fails when the handle_errors option was not selected
and there is no remaining valid mirror leg, writes return success even
though they weren't actually written to any device. This patch
completes them with EIO instead.
This code path is taken:
do_writes:
bio_list_merge(&ms->failures, &sync);
do_failures:
if (!get_valid_mirror(ms)) (false)
else if (errors_handled(ms)) (false)
else bio_endio(bio, 0);
The logic in do_failures is based on presuming that the write was already
tried: if it succeeded at least on one leg (without handle_errors) it
is reported as success.
Reference: https://bugzilla.redhat.com/show_bug.cgi?id=555197
Signed-off-by: Mikulas Patocka <mpatocka@redhat.com>
Signed-off-by: Alasdair G Kergon <agk@redhat.com>
|
