| Age | Commit message (Collapse) | Author |
|---|
|
git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio
Pull GPIO updates from Linus Walleij:
"This is the bulk of GPIO changes for the v4.11 cycle
Core changes:
- Augment fwnode_get_named_gpiod() to configure the GPIO pin
immediately after requesting it like all other APIs do. This is a
treewide change also updating all users.
- Pass a GPIO label down to gpiod_request() from
fwnode_get_named_gpiod(). This makes debugfs and the userspace ABI
correctly reflect the current in-kernel consumer of a pin taken
using this abstraction. This is a treewide change also updating all
users.
- Rename devm_get_gpiod_from_child() to
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object. This is a treewide change
also updating all users.
- Make it possible to take multiple GPIOs in a single hog of device
tree hogs.
- The refactorings switching GPIO chips to use the .set_config()
callback using standard pin control properties and providing a
backend into the pin control subsystem that were also merged into
the pin control tree naturally appear here too.
Testing instrumentation:
- A whole slew of cleanups and improvements to the mockup GPIO
driver. We now have an extended userspace test exercising the
subsystem, and we can inject interrupts etc from userspace to fully
test the core GPIO functionality.
New drivers:
- New driver for the Cortina Systems Gemini GPIO controller.
- New driver for the Exar XR17V352/354/358 chips.
- New driver for the ACCES PCI-IDIO-16 PCI GPIO card.
Driver changes:
- RCAR: set the irqchip parent device, add fine-grained runtime PM
support.
- pca953x: support optional RESET control line on the chip.
- DaVinci: cleanups and simplifications. Add support for multiple
instances.
- .set_multiple() and naming of lines on more or less all of the
ISA/PCI GPIO controllers.
- mcp23s08: refactored to use regmap as a first step to further
rewrites and modernizations"
* tag 'gpio-v4.11-1' of git://git.kernel.org/pub/scm/linux/kernel/git/linusw/linux-gpio: (61 commits)
gpio: reintroduce devm_get_gpiod_from_child()
gpio: pci-idio-16: Fix PCI BAR index
gpio: pci-idio-16: Fix PCI device ID code
gpio: mockup: implement event injecting over debugfs
gpio: mockup: add a dummy irqchip
gpio: mockup: implement naming the lines
gpio: mockup: code shrink
gpio: mockup: readability tweaks
gpio: Add GPIO support for the ACCES PCI-IDIO-16
gpio: Add the devm_fwnode_get_index_gpiod_from_child() helper
gpio: Rename devm_get_gpiod_from_child()
gpio: mcp23s08: Select REGMAP/REGMAP_I2C to fix build error
gpio: ws16c48: Add support for GPIO names
gpio: gpio-mm: Add support for GPIO names
gpio: 104-idio-16: Add support for GPIO names
gpio: 104-idi-48: Add support for GPIO names
gpio: 104-dio-48e: Add support for GPIO names
gpio: ws16c48: Remove unnecessary driver_data set
gpio: gpio-mm: Remove unnecessary driver_data set
gpio: 104-idio-16: Remove unnecessary driver_data set
...
|
|
LED class heartbeat trigger allowed only for blinking with max_brightness
value. This patch adds more flexibility by exploiting part of LED core
software blink infrastructure.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
|
|
Rename devm_get_gpiod_from_child() into
devm_fwnode_get_gpiod_from_child() to reflect the fact that this
function is operating on a fwnode object.
Signed-off-by: Boris Brezillon <boris.brezillon@free-electrons.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Some LEDs may have their brightness level changed autonomously
(outside of kernel control) by hardware / firmware. This commit
adds support for an optional brightness_hw_changed attribute to
signal such changes to userspace (if a driver can detect them):
What: /sys/class/leds/<led>/brightness_hw_changed
Date: January 2017
KernelVersion: 4.11
Description:
Last hardware set brightness level for this LED. Some LEDs
may be changed autonomously by hardware/firmware. Only LEDs
where this happens and the driver can detect this, will
have this file.
This file supports poll() to detect when the hardware
changes the brightness.
Reading this file will return the last brightness level set
by the hardware, this may be different from the current
brightness.
Drivers which want to support this, simply add LED_BRIGHT_HW_CHANGED to
their flags field and call led_classdev_notify_brightness_hw_changed()
with the hardware set brightness when they detect a hardware / firmware
triggered brightness change.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
gcc gets confused about the control flow in ktd2692_parse_dt(), causing
it to warn about what seems like a potential bug:
drivers/leds/leds-ktd2692.c: In function 'ktd2692_probe':
drivers/leds/leds-ktd2692.c:244:15: error: '*((void *)&led_cfg+8)' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:225:7: error: 'led_cfg.flash_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
drivers/leds/leds-ktd2692.c:232:3: error: 'led_cfg.movie_max_microamp' may be used uninitialized in this function [-Werror=maybe-uninitialized]
The code is fine, and slightly reworking it in an equivalent way lets
gcc figure that out too, which gets rid of the warning.
Fixes: 77e7915b15bb ("leds: ktd2692: Add missing of_node_put")
Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
Currently all users of fwnode_get_named_gpiod() have no way to
specify a label for the GPIO. So GPIOs listed in debugfs are shown
with label "?". With this change a proper label is used.
Also adjust all users so they can pass a label, properly retrieved
from device tree properties.
Signed-off-by: Alexander Stein <alexander.stein@systec-electronic.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Acked-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
Acked-by: Bartlomiej Zolnierkiewicz <b.zolnierkie@samsung.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
Make fwnode_get_named_gpiod() consistent with the rest of
gpiod_get() like API, i.e. configure GPIO pin immediately after
request.
Besides obvious clean up it will help to configure pins based
on firmware provided resources.
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
|
When the state names got added a script was used to add the extra argument
to the calls. The script basically converted the state constant to a
string, but the cleanup to convert these strings into meaningful ones did
not happen.
Replace all the useless strings with 'subsys/xxx/yyy:state' strings which
are used in all the other places already.
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Sebastian Siewior <bigeasy@linutronix.de>
Link: http://lkml.kernel.org/r/20161221192112.085444152@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
This patch enables ACPI support for leds-pca955x driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
If the driver is built as a module, autoload won't work because the module
alias information is not filled. So user-space can't match the registered
device with the corresponding module.
Export the module alias information using the MODULE_DEVICE_TABLE() macro.
Before this patch:
$ modinfo drivers/leds//leds-netxbig.ko | grep alias
alias: platform:leds-netxbig
After this patch:
$ modinfo drivers/leds//leds-netxbig.ko | grep alias
alias: platform:leds-netxbig
alias: of:N*T*Clacie,netxbig-ledsC*
alias: of:N*T*Clacie,netxbig-leds
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch enables ACPI support for leds-pca963x driver.
Signed-off-by: Tin Huynh <tnhuynh@apm.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use builtin_platform_driver() helper to simplify the code.
Signed-off-by: Geliang Tang <geliangtang@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd into linux-leds/for-next
Pull PM8XXX namespace cleanup from Lee Jones.
* tag 'ib-mfd-arm-leds-v4.10' of git://git.kernel.org/pub/scm/linux/kernel/git/lee/mfd:
mfd: qcom-pm8xxx: Clean up PM8XXX namespace
|
|
All 3 of led_timer_func, led_set_brightness and led_set_software_blink
set blink_brightness. If led_timer_func or led_set_software_blink race
with led_set_brightness they may end up overwriting the new
blink_brightness. The new atomic work_flags does not protect against
this as it just protects the flags and not blink_brightness.
This commit introduces a new new_blink_brightness value which gets
set by led_set_brightness and read by led_timer_func on LED on, fixing
this.
Dealing with the new brightness at LED on time, makes the new
brightness apply sooner, which also fixes a led_set_brightness which
happens while a oneshot blink which ends in LED on is running not
getting applied.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
All the LED_BLINK* flags are accessed read-modify-write from e.g.
led_set_brightness and led_blink_set_oneshot while both
set_brightness_work and the blink_timer may be running.
If these race then the modify step done by one of them may be lost,
switch the LED_BLINK* flags to a new atomic work_flags bit-field
to avoid this race.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Add the driver to support User LEDs on PXI Embedded Controller.
Signed-off-by: Hui Chun Ong <hui.chun.ong@ni.com>
Signed-off-by: Brad Mouring <brad.mouring@ni.com>
Acked-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Verify that vendor is Mellanox as the first step of initialization.
If it is not - return ENODEV.
Change module license from "GPL v2" to "Dual BSD/GPL".
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Allow chip to enter low power state when no LEDs are being lit or in
blink mode.
Cc: Peter Meerwald <p.meerwald@bct-electronic.com>,
Cc: Ricardo Ribalda <ricardo.ribalda@gmail.com>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The value for a led's default_trigger should come from platform data
instead of data (which is always 0).
Signed-off-by: Felix Brack <fb@ltec.ch>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
PCA9632TK part seems to incorrectly blink at ~1.3x of the programmed
rate. This patchset add a nxp,period-scale devicetree property to
adjust for this misconfiguration.
Signed-off-by: Matt Ranostay <matt@ranostay.consulting>
Cc: Tony Lindgren <tony@atomide.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
If the driver is built as a module, I2C module alias information is not
filled so the module won't be autoloaded if the device isn't registered
over ACPI. Export the I2C device table alias with MODULE_DEVICE_TABLE()
macro so the information is exported in the module.
Before this patch:
$ modinfo drivers/leds/leds-lp3952.ko | grep alias
alias: acpi*:TXNW3952:*
After this patch:
$ modinfo drivers/leds/leds-lp3952.ko | grep alias
alias: i2c:lp3952
alias: acpi*:TXNW3952:*
Signed-off-by: Javier Martinez Canillas <javier@osg.samsung.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Fix the register access shift argument calculation introduced with
commit a59ce6584d56 ("leds: leds-mc13783: Add MC34708 LED support")
and re-enable access to the "keypad" led for MC13892 MFC devices.
Signed-off-by: Alexander Kurz <akurz@blala.de>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Fix english spelling.
Signed-off-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Use a macro instead of hard-coding the max device node name size. The
uleds driver introduced a macro for this value, so using it.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This driver creates a userspace leds driver similar to uinput.
New LEDs are created by opening /dev/uleds and writing a uleds_user_dev
struct. A new LED class device is registered with the name given in the
struct. Reading will return a single byte that is the current brightness.
The poll() syscall is also supported. It will be triggered whenever the
brightness changes. Closing the file handle to /dev/uleds will remove
the leds class device.
Signed-off-by: David Lechner <david@lechnology.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The Kconfig and file naming for the PM8xxx driver is totally
confusing:
- Kconfig options MFD_PM8XXX and MFD_PM8921_CORE, some in-kernel
users depending on or selecting either at random.
- A driver file named pm8921-core.c even if it is indeed
used by the whole PM8xxx family of chips.
- An irqchip named pm8xxx since it was (I guess) realized that
the driver was generic for all pm8xxx PMICs.
As I may want to add support for PM8901 this is starting to get
really messy. Fix this situation by:
- Remove the MFD_PM8921_CORE symbol and rely solely on MFD_PM8XXX
and convert all users, including LEDs Kconfig and ARM defconfigs
for qcom and multi_v7 to use that single symbol.
- Renaming the driver to qcom-pm8xxx.c to fit along the two
other qcom* prefixed drivers.
- Rename functions withing the driver from 8921 to 8xxx to
indicate it is generic.
- Just drop the =m config from the pxa_defconfig, I have no clue
why it is even there, it is not a Qualcomm platform. (Possibly
older Kconfig noise from saveconfig.)
Cc: Stephen Boyd <sboyd@codeaurora.org>
Cc: Neil Armstrong <narmstrong@baylibre.com>
Cc: Abhijeet Dharmapurikar <adharmap@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Andy Gross <andy.gross@linaro.org>
Acked-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Lee Jones <lee.jones@linaro.org>
|
|
Log error message if kobject_uevent_env() fails in led_trigger_set().
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
|
|
If led_trigger_set() is called with "trig" argument set to NULL, and there
is no trigger to remove then the function should return immediately so
as to avoid doing unnecessary allocation and sending uevent.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Reported-by: Daniel Romell <daro@hms.se>
Acked-by Daniel Romell <daro@hms.se>
|
|
Simplify the error handling and add a missing call to fwnode_handle_put
when checking led.name.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Using the managed version of led_classdev_register allows to
significantly simplify the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Checking for the presence of the property first isn't strictly needed
as we can react on the return code of fwnode_property_read_string.
Also, even if the presence of a property "label" was checked,
reading a string value for it theoretically still can fail and
this case isn't handled.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Definition of np can be moved into the loop as well to simplify
the code a little.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Add a helper for the container_of as it's used more than once.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
gpiod_get_value_cansleep returns 0, 1, or an error code.
So far errors are not handled and treated the same as 1.
Change this to bail out if an error code is returned and
remove the double negation.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Introduce a typedef gpio_blink_set_t to improve readability of the code.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This makes it possible to create a set of LEDs for Mellanox systems:
"msx6710", "msx6720", "msb7700", "msn2700", "msx1410", "msn2410",
"msb7800", "msn2740", "msn2100".
Driver obtains LED devices according to system configuration, provided
through system DMI data, like mlxcpld:fan1:green, mlxcpld:fan1:red and
creates devices in form: "devicename:colour:function".
LED setting is controlled through on board CPLD Lattice device.
For setting particular LED off, solid, blink:
echo 0 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:status\:green/brightness
echo timer > /sys/class/leds/mlxcpld\:status\:green/trigger
On module probing all LEDs are set green, on removing - off.
Last setting overwrites previous, f.e. sequence for
changing LED from green - red - green:
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:red/brightness
echo 1 > /sys/class/leds/mlxcpld\:psu\:green/brightness
Note: LEDs cannot be turned on/off simultaneously.
The Kconfig currently controlling compilation of this code is:
drivers/leds/Kconfig:config LEDS_MLXCPLD
Signed-off-by: Vadim Pasternak <vadimp@mellanox.com>
Reviewed-by: Jiri Pirko <jiri@mellanox.com>
Reviewed-by: Wei Yongjun <weiyongjun1@huawei.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This adds a driver for the six PM8058 LEDs, three ordinary LEDs,
two "flash" LEDs and one "keypad" LED.
The "keypad" and "flash" LEDs are not really hard-wired to these
usecases: for example on the APQ8060 Dragonboard, the "keypad"
LED is instead used to drive an IR LED used for the proximity
sensor. The "flash" LEDs are just ordinary high-current LED
drivers.
Cc: linux-arm-msm@vger.kernel.org
Cc: Andy Gross <andy.gross@linaro.org>
Cc: Stephen Boyd <sboyd@codeaurora.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Per the documentation, use scnprintf instead of sprintf to ensure there
is never more than PAGE_SIZE bytes of trigger names put into the
buffer.
Signed-off-by: Nathan Sullivan <nathan.sullivan@ni.com>
Signed-off-by: Zach Brown <zach.brown@ni.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The Kconfig currently controlling compilation of this code is:
drivers/leds/trigger/Kconfig:menuconfig LEDS_TRIGGERS
drivers/leds/trigger/Kconfig: bool "LED Trigger support"
...meaning that it currently is not being built as a module by anyone.
Lets remove the couple traces of modular infrastructure use, so that
when reading the driver there is no doubt it is builtin-only.
We also delete the MODULE_LICENSE tag etc. since all that information
is already contained at the top of the file in the comments.
We don't replace module.h with init.h since the file doesn't need that.
However it does use EXPORT_SYMBOL, so we add the export.h header.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This is a driver for the Integrated Silicon Solution Inc. LED driver
chips series IS31FL319x. They can drive 1, 3, 6 or up to 9
LEDs.
Each LED is individually controllable in brightness (through pwm)
in 256 steps so that RGB LEDs can show any of ca. 16 Mio colors.
The maximum current of the LEDs can be programmed and limited to
5 .. 40mA through a device tree property.
The chip is connected through I2C and can have one of 4 addresses
in the range 0x64 .. 0x67 depending on how the AD pin is connected. The
address is defined by the reg property as usual.
The chip also has a shutdown input which could be connected to a GPIO,
but this driver uses software shutdown if all LEDs are inactivated.
The chip also has breathing and audio features which are not fully
supported by this driver.
Tested-on: OMAP5 based Pyra handheld prototype.
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Signed-off-by: Andrey Utkin <andrey_utkin@fastmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux
Pull powerpc updates from Michael Ellerman:
"Highlights:
- PowerNV PCI hotplug support.
- Lots more Power9 support.
- eBPF JIT support on ppc64le.
- Lots of cxl updates.
- Boot code consolidation.
Bug fixes:
- Fix spin_unlock_wait() from Boqun Feng
- Fix stack pointer corruption in __tm_recheckpoint() from Michael
Neuling
- Fix multiple bugs in memory_hotplug_max() from Bharata B Rao
- mm: Ensure "special" zones are empty from Oliver O'Halloran
- ftrace: Separate the heuristics for checking call sites from
Michael Ellerman
- modules: Never restore r2 for a mprofile-kernel style mcount() call
from Michael Ellerman
- Fix endianness when reading TCEs from Alexey Kardashevskiy
- start rtasd before PCI probing from Greg Kurz
- PCI: rpaphp: Fix slot registration for multiple slots under a PHB
from Tyrel Datwyler
- powerpc/mm: Add memory barrier in __hugepte_alloc() from Sukadev
Bhattiprolu
Cleanups & fixes:
- Drop support for MPIC in pseries from Rashmica Gupta
- Define and use PPC64_ELF_ABI_v2/v1 from Michael Ellerman
- Remove unused symbols in asm-offsets.c from Rashmica Gupta
- Fix SRIOV not building without EEH enabled from Russell Currey
- Remove kretprobe_trampoline_holder from Thiago Jung Bauermann
- Reduce log level of PCI I/O space warning from Benjamin
Herrenschmidt
- Add array bounds checking to crash_shutdown_handlers from Suraj
Jitindar Singh
- Avoid -maltivec when using clang integrated assembler from Anton
Blanchard
- Fix array overrun in ppc_rtas() syscall from Andrew Donnellan
- Fix error return value in cmm_mem_going_offline() from Rasmus
Villemoes
- export cpu_to_core_id() from Mauricio Faria de Oliveira
- Remove old symbols from defconfigs from Andrew Donnellan
- Update obsolete comments in setup_32.c about entry conditions from
Benjamin Herrenschmidt
- Add comment explaining the purpose of setup_kdump_trampoline() from
Benjamin Herrenschmidt
- Merge the RELOCATABLE config entries for ppc32 and ppc64 from Kevin
Hao
- Remove RELOCATABLE_PPC32 from Kevin Hao
- Fix .long's in tlb-radix.c to more meaningful from Balbir Singh
Minor cleanups & fixes:
- Andrew Donnellan, Anna-Maria Gleixner, Anton Blanchard, Benjamin
Herrenschmidt, Bharata B Rao, Christophe Leroy, Colin Ian King,
Geliang Tang, Greg Kurz, Madhavan Srinivasan, Michael Ellerman,
Michael Ellerman, Stephen Rothwell, Stewart Smith.
Freescale updates from Scott:
- "Highlights include more 8xx optimizations, device tree updates,
and MVME7100 support."
PowerNV PCI hotplug from Gavin Shan:
- PCI: Add pcibios_setup_bridge()
- Override pcibios_setup_bridge()
- Remove PCI_RESET_DELAY_US
- Move pnv_pci_ioda_setup_opal_tce_kill() around
- Increase PE# capacity
- Allocate PE# in reverse order
- Create PEs in pcibios_setup_bridge()
- Setup PE for root bus
- Extend PCI bridge resources
- Make pnv_ioda_deconfigure_pe() visible
- Dynamically release PE
- Update bridge windows on PCI plug
- Delay populating pdn
- Support PCI slot ID
- Use PCI slot reset infrastructure
- Introduce pnv_pci_get_slot_id()
- Functions to get/set PCI slot state
- PCI/hotplug: PowerPC PowerNV PCI hotplug driver
- Print correct PHB type names
Power9 idle support from Shreyas B. Prabhu:
- set power_save func after the idle states are initialized
- Use PNV_THREAD_WINKLE macro while requesting for winkle
- make hypervisor state restore a function
- Rename idle_power7.S to idle_book3s.S
- Rename reusable idle functions to hardware agnostic names
- Make pnv_powersave_common more generic
- abstraction for saving SPRs before entering deep idle states
- Add platform support for stop instruction
- cpuidle/powernv: Use CPUIDLE_STATE_MAX instead of MAX_POWERNV_IDLE_STATES
- cpuidle/powernv: cleanup cpuidle-powernv.c
- cpuidle/powernv: Add support for POWER ISA v3 idle states
- Use deepest stop state when cpu is offlined
Power9 PMU from Madhavan Srinivasan:
- factor out power8 pmu macros and defines
- factor out power8 pmu functions
- factor out power8 __init_pmu code
- Add power9 event list macros for generic and cache events
- Power9 PMU support
- Export Power9 generic and cache events to sysfs
Power9 preliminary interrupt & PCI support from Benjamin Herrenschmidt:
- Add XICS emulation APIs
- Move a few exception common handlers to make room
- Add support for HV virtualization interrupts
- Add mechanism to force a replay of interrupts
- Add ICP OPAL backend
- Discover IODA3 PHBs
- pci: Remove obsolete SW invalidate
- opal: Add real mode call wrappers
- Rename TCE invalidation calls
- Remove SWINV constants and obsolete TCE code
- Rework accessing the TCE invalidate register
- Fallback to OPAL for TCE invalidations
- Use the device-tree to get available range of M64's
- Check status of a PHB before using it
- pci: Don't try to allocate resources that will be reassigned
Other Power9:
- Send SIGBUS on unaligned copy and paste from Chris Smart
- Large Decrementer support from Oliver O'Halloran
- Load Monitor Register Support from Jack Miller
Performance improvements from Anton Blanchard:
- Avoid load hit store in __giveup_fpu() and __giveup_altivec()
- Avoid load hit store in setup_sigcontext()
- Remove assembly versions of strcpy, strcat, strlen and strcmp
- Align hot loops of some string functions
eBPF JIT from Naveen N. Rao:
- Fix/enhance 32-bit Load Immediate implementation
- Optimize 64-bit Immediate loads
- Introduce rotate immediate instructions
- A few cleanups
- Isolate classic BPF JIT specifics into a separate header
- Implement JIT compiler for extended BPF
Operator Panel driver from Suraj Jitindar Singh:
- devicetree/bindings: Add binding for operator panel on FSP machines
- Add inline function to get rc from an ASYNC_COMP opal_msg
- Add driver for operator panel on FSP machines
Sparse fixes from Daniel Axtens:
- make some things static
- Introduce asm-prototypes.h
- Include headers containing prototypes
- Use #ifdef __BIG_ENDIAN__ #else for REG_BYTE
- kvm: Clarify __user annotations
- Pass endianness to sparse
- Make ppc_md.{halt, restart} __noreturn
MM fixes & cleanups from Aneesh Kumar K.V:
- radix: Update LPCR HR bit as per ISA
- use _raw variant of page table accessors
- Compile out radix related functions if RADIX_MMU is disabled
- Clear top 16 bits of va only on older cpus
- Print formation regarding the the MMU mode
- hash: Update SDR1 size encoding as documented in ISA 3.0
- radix: Update PID switch sequence
- radix: Update machine call back to support new HCALL.
- radix: Add LPID based tlb flush helpers
- radix: Add a kernel command line to disable radix
- Cleanup LPCR defines
Boot code consolidation from Benjamin Herrenschmidt:
- Move epapr_paravirt_early_init() to early_init_devtree()
- cell: Don't use flat device-tree after boot
- ge_imp3a: Don't use the flat device-tree after boot
- mpc85xx_ds: Don't use the flat device-tree after boot
- mpc85xx_rdb: Don't use the flat device-tree after boot
- Don't test for machine type in rtas_initialize()
- Don't test for machine type in smp_setup_cpu_maps()
- dt: Add of_device_compatible_match()
- Factor do_feature_fixup calls
- Move 64-bit feature fixup earlier
- Move 64-bit memory reserves to setup_arch()
- Use a cachable DART
- Move FW feature probing out of pseries probe()
- Put exception configuration in a common place
- Remove early allocation of the SMU command buffer
- Move MMU backend selection out of platform code
- pasemi: Remove IOBMAP allocation from platform probe()
- mm/hash: Don't use machine_is() early during boot
- Don't test for machine type to detect HEA special case
- pmac: Remove spurrious machine type test
- Move hash table ops to a separate structure
- Ensure that ppc_md is empty before probing for machine type
- Move 64-bit probe_machine() to later in the boot process
- Move 32-bit probe() machine to later in the boot process
- Get rid of ppc_md.init_early()
- Move the boot time info banner to a separate function
- Move setting of {i,d}cache_bsize to initialize_cache_info()
- Move the content of setup_system() to setup_arch()
- Move cache info inits to a separate function
- Re-order the call to smp_setup_cpu_maps()
- Re-order setup_panic()
- Make a few boot functions __init
- Merge 32-bit and 64-bit setup_arch()
Other new features:
- tty/hvc: Use IRQF_SHARED for OPAL hvc consoles from Sam Mendoza-Jonas
- tty/hvc: Use opal irqchip interface if available from Sam Mendoza-Jonas
- powerpc: Add module autoloading based on CPU features from Alastair D'Silva
- crypto: vmx - Convert to CPU feature based module autoloading from Alastair D'Silva
- Wake up kopald polling thread before waiting for events from Benjamin Herrenschmidt
- xmon: Dump ISA 2.06 SPRs from Michael Ellerman
- xmon: Dump ISA 2.07 SPRs from Michael Ellerman
- Add a parameter to disable 1TB segs from Oliver O'Halloran
- powerpc/boot: Add OPAL console to epapr wrappers from Oliver O'Halloran
- Assign fixed PHB number based on device-tree properties from Guilherme G. Piccoli
- pseries: Add pseries hotplug workqueue from John Allen
- pseries: Add support for hotplug interrupt source from John Allen
- pseries: Use kernel hotplug queue for PowerVM hotplug events from John Allen
- pseries: Move property cloning into its own routine from Nathan Fontenot
- pseries: Dynamic add entires to associativity lookup array from Nathan Fontenot
- pseries: Auto-online hotplugged memory from Nathan Fontenot
- pseries: Remove call to memblock_add() from Nathan Fontenot
cxl:
- Add set and get private data to context struct from Michael Neuling
- make base more explicitly non-modular from Paul Gortmaker
- Use for_each_compatible_node() macro from Wei Yongjun
- Frederic Barrat
- Abstract the differences between the PSL and XSL
- Make vPHB device node match adapter's
- Philippe Bergheaud
- Add mechanism for delivering AFU driver specific events
- Ignore CAPI adapters misplaced in switched slots
- Refine slice error debug messages
- Andrew Donnellan
- static-ify variables to fix sparse warnings
- PCI/hotplug: pnv_php: export symbols and move struct types needed by cxl
- PCI/hotplug: pnv_php: handle OPAL_PCI_SLOT_OFFLINE power state
- Add cxl_check_and_switch_mode() API to switch bi-modal cards
- remove dead Kconfig options
- fix potential NULL dereference in free_adapter()
- Ian Munsie
- Update process element after allocating interrupts
- Add support for CAPP DMA mode
- Fix allowing bogus AFU descriptors with 0 maximum processes
- Fix allocating a minimum of 2 pages for the SPA
- Fix bug where AFU disable operation had no effect
- Workaround XSL bug that does not clear the RA bit after a reset
- Fix NULL pointer dereference on kernel contexts with no AFU interrupts
- powerpc/powernv: Split cxl code out into a separate file
- Add cxl_slot_is_supported API
- Enable bus mastering for devices using CAPP DMA mode
- Move cxl_afu_get / cxl_afu_put to base
- Allow a default context to be associated with an external pci_dev
- Do not create vPHB if there are no AFU configuration records
- powerpc/powernv: Add support for the cxl kernel api on the real phb
- Add support for using the kernel API with a real PHB
- Add kernel APIs to get & set the max irqs per context
- Add preliminary workaround for CX4 interrupt limitation
- Add support for interrupts on the Mellanox CX4
- Workaround PE=0 hardware limitation in Mellanox CX4
- powerpc/powernv: Fix pci-cxl.c build when CONFIG_MODULES=n
selftests:
- Test unaligned copy and paste from Chris Smart
- Load Monitor Register Tests from Jack Miller
- Cyril Bur
- exec() with suspended transaction
- Use signed long to read perf_event_paranoid
- Fix usage message in context_switch
- Fix generation of vector instructions/types in context_switch
- Michael Ellerman
- Use "Delta" rather than "Error" in normal output
- Import Anton's mmap & futex micro benchmarks
- Add a test for PROT_SAO"
* tag 'powerpc-4.8-1' of git://git.kernel.org/pub/scm/linux/kernel/git/powerpc/linux: (263 commits)
powerpc/mm: Parenthesise IS_ENABLED() in if condition
tty/hvc: Use opal irqchip interface if available
tty/hvc: Use IRQF_SHARED for OPAL hvc consoles
selftests/powerpc: exec() with suspended transaction
powerpc: Improve comment explaining why we modify VRSAVE
powerpc/mm: Drop unused externs for hpte_init_beat[_v3]()
powerpc/mm: Rename hpte_init_lpar() and move the fallback to a header
powerpc/mm: Fix build break when PPC_NATIVE=n
crypto: vmx - Convert to CPU feature based module autoloading
powerpc: Add module autoloading based on CPU features
powerpc/powernv/ioda: Fix endianness when reading TCEs
powerpc/mm: Add memory barrier in __hugepte_alloc()
powerpc/modules: Never restore r2 for a mprofile-kernel style mcount() call
powerpc/ftrace: Separate the heuristics for checking call sites
powerpc: Merge 32-bit and 64-bit setup_arch()
powerpc/64: Make a few boot functions __init
powerpc: Re-order setup_panic()
powerpc: Re-order the call to smp_setup_cpu_maps()
powerpc/32: Move cache info inits to a separate function
powerpc/64: Move the content of setup_system() to setup_arch()
...
|
|
git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip
Pull smp hotplug updates from Thomas Gleixner:
"This is the next part of the hotplug rework.
- Convert all notifiers with a priority assigned
- Convert all CPU_STARTING/DYING notifiers
The final removal of the STARTING/DYING infrastructure will happen
when the merge window closes.
Another 700 hundred line of unpenetrable maze gone :)"
* 'smp-hotplug-for-linus' of git://git.kernel.org/pub/scm/linux/kernel/git/tip/tip: (70 commits)
timers/core: Correct callback order during CPU hot plug
leds/trigger/cpu: Move from CPU_STARTING to ONLINE level
powerpc/numa: Convert to hotplug state machine
arm/perf: Fix hotplug state machine conversion
irqchip/armada: Avoid unused function warnings
ARC/time: Convert to hotplug state machine
clocksource/atlas7: Convert to hotplug state machine
clocksource/armada-370-xp: Convert to hotplug state machine
clocksource/exynos_mct: Convert to hotplug state machine
clocksource/arm_global_timer: Convert to hotplug state machine
rcu: Convert rcutree to hotplug state machine
KVM/arm/arm64/vgic-new: Convert to hotplug state machine
smp/cfd: Convert core to hotplug state machine
x86/x2apic: Convert to CPU hotplug state machine
profile: Convert to hotplug state machine
timers/core: Convert to hotplug state machine
hrtimer: Convert to hotplug state machine
x86/tboot: Convert to hotplug state machine
arm64/armv8 deprecated: Convert to hotplug state machine
hwtracing/coresight-etm4x: Convert to hotplug state machine
...
|
|
There is no need the ledtriger to be called *that* early in the hotplug
process (+ with disabled interrupts). As explained by Jacek Anaszewski [0]
there is no need for it.
Therefore this patch moves it to the ONLINE/PREPARE_DOWN level using the
dynamic registration for the id.
[0] https://lkml.kernel.org/r/578C92BC.2070603@samsung.com
Signed-off-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: rt@linutronix.de
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: linux-leds@vger.kernel.org
Link: http://lkml.kernel.org/r/1469028295-14702-1-git-send-email-bigeasy@linutronix.de
Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
|
|
Otherwise the driver module will not be automatically probed.
Fixes: 9d7cffaf99f5 ("leds: Add driver for the ISSI IS31FL32xx family of LED controllers")
Fixes: e0442d7def8f ("leds: Add SN3218 and SN3216 support to the IS31FL32XX driver")
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Signed-off-by: H. Nikolaus Schaller <hns@goldelico.com>
Tested-by: David Rivshin <drivshin@allworx.com>
Acked-by: David Rivshin <drivshin@allworx.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
The chip can drive 2 sets of RGB leds. Controller can
be controlled via PWM, I2C and audio synchronisation.
This driver uses I2C to communicate with the chip.
Datasheet: http://www.ti.com/lit/gpn/lp3952
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Reviewed-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This is a straightforward conversion. We place this callback last
in the list so that the LED illuminates only after a successful
bring up sequence.
( NOTE: The patch adds a FIXME question about the callback used,
this question should probably be revisited later on.)
Signed-off-by: Richard Cochran <rcochran@linutronix.de>
Signed-off-by: Anna-Maria Gleixner <anna-maria@linutronix.de>
Reviewed-by: Sebastian Andrzej Siewior <bigeasy@linutronix.de>
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Cc: Linus Walleij <linus.walleij@linaro.org>
Cc: Paul Gortmaker <paul.gortmaker@windriver.com>
Cc: Peter Zijlstra <peterz@infradead.org>
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Thomas Gleixner <tglx@linutronix.de>
Cc: linux-leds@vger.kernel.org
Cc: rt@linutronix.de
Link: http://lkml.kernel.org/r/20160713153336.465496902@linutronix.de
Signed-off-by: Ingo Molnar <mingo@kernel.org>
|
|
When working with Device Tree we iterate over children of "gpio-leds"
compatible node and create LED device for each of them. We take care of
all common DT properties (label, default trigger, state, etc.), however
some triggers may want to support more of them.
It could be useful for timer trigger to support setting delay on/off
values with Device Tree property. Or for transient trigger to support
e.g. duration property.
We obviously should handle such properties in triggers, not in generic
code. To let trigger drivers read properties from DT node we need to set
of_node to point the relevant node. This change allows using all kind of
of helpers in e.g. "activate" callbacks.
Signed-off-by: Rafał Miłecki <zajec5@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
If an invalid trigger name is provided via sysfs currently no error
is returned. Therefore it's not possible to determine whether the
trigger was set successfully.
Fix this by returning -EINVAL if no trigger is matched.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
An opal_msg of type OPAL_MSG_ASYNC_COMP contains the return code in the
params[1] struct member. However this isn't intuitive or obvious when
reading the code and requires that a user look at the skiboot
documentation or opal-api.h to verify this.
Add an inline function to get the return code from an opal_msg and update
call sites accordingly.
Signed-off-by: Suraj Jitindar Singh <sjitindarsingh@gmail.com>
Signed-off-by: Michael Ellerman <mpe@ellerman.id.au>
|
