summaryrefslogtreecommitdiff
path: root/drivers/leds/leds-lp55xx-common.c
AgeCommit message (Collapse)Author
2013-10-25leds: lp55xx: handle enable pin in driverSebastian Reichel
This patch moves the handling of the chip's enable pin from the board code into the driver. It also updates all board-code files using the driver to incorporate this change. This is needed for device tree support of the enable pin. Signed-off-by: Sebastian Reichel <sre@debian.org> Acked-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Tony Lindgren <tony@atomide.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-10-22leds: lp55xx: enable setting default triggerLinus Walleij
This enables setting a default trigger on an LP55xx channel, either from platform data or device tree. This mechanism is identical to the mechanism for GPIO LEDs and references the common LEDs device tree bindings. Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Tested-by: Milo Kim <milo.kim@ti.com> Acked-by: Milo Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-08-26leds: support new LP8501 device - another LP55xx commonKim, Milo
LP8501 can drive up to 9 channels like LP5523. LEDs can be controlled directly via the I2C and programmable engines are supported. LP55xx common driver LP8501 is one of LP55xx family device, so LP55xx common code are used. Chip specific data is defined in the structure, 'lp55xx_device_config'. Differences between LP8501 and LP5523 Different register layout for LED output control and others. LP8501 specific feature for separate output power selection. LP8501 doesn't support external clock detection. Different programming engine data. LP8501 specific feature - output power selection Output channels are selected by power selection - Vout or Vdd. Separate power for VDD1-6 and VDD7-9 are available. It is configurable in the platform data. To support this feature, LP55xx DT structure and header are changed. Device tree binding is updated as well. LED pattern data Example pattern data is updated in the driver documentation. Signed-off-by: Milo Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-06-20leds: lp55xx: support dynamic channel settings in the device tree structureKim, Milo
Currently, the LP55xx DT structure supports max 3 channels. However, LP5523 has max 9 channels and LP5562 has 4 channels. To enhance this constraint, the DT structure has been changed. (a) Use the child node for various channel settings instead of fixed array (b) Remove 'num_channel' property. This value can be retrieved by counting the children node. (c) 'chan-name' property supported (d) Documentation updates for LP5521 and LP5523 (cooloney@gmail.com: fix a coding style issue in leds-lp55xx.txt) Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com> Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Reviewed-by: Linus Walleij <linus.walleij@linaro.org> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-06-20leds: lp55xx: add support for Device Tree bindingsLinus Walleij
This patch allows the lp5521 driver to be successfully probed and initialised when Device Tree support is enabled. Based on a patch by Gabriel Fernandez, rewritten in accordance with review feedback. Cc: Gabriel Fernandez <gabriel.fernandez@stericsson.com> Signed-off-by: Linus Walleij <linus.walleij@linaro.org> Acked-by: Milo Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-04-01leds: lp55xx: use common clock framework when external clock is usedKim, Milo
Program execution is timed with 32768Hz clock in the LP55xx family devices. To run LED functionalities, LP55xx devices provide two options. One is using internal clock. The other is using external clock. This patch enables external clock detection automatically. If external clock is not detected, then the internal clock will be used in the LP55xx driver. Valid clock rate is 32768Hz in LP55xx devices. This new API is used in each LP55xx driver like LP5521 and LP5562. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-04-01leds: lp55xx: fix the sysfs read operationKim, Milo
According to a sysfs documentation(Documentation/filesystem/sysfs.txt), scnprintf() should be used in a read operation method. It guarantees safe buffer size(PAGE_SIZE) which is allocated by the sysfs. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-04-01leds: add new LP5562 LED driverKim, Milo
LP5562 can drive up to 4 channels, RGB and White. LEDs can be controlled directly via the led class control interface. LP55xx common driver LP5562 is one of LP55xx family device, so LP55xx common code are used. On the other hand, chip specific configuration is defined in the structure 'lp55xx_device_config' LED pattern data LP5562 has also internal program memory which is used for running various LED patterns. LP5562 driver supports the firmware interface and the predefined pattern data as well. LP5562 device attributes: 'led_pattern' and 'engine_mux' A 'led_pattern' is an index code which runs the predefined pattern data. And 'engine_mux' is updated with the firmware interface is activated. Detailed description has been updated in the documentation files, 'leds-lp55xx.txt' and 'leds-lp5562.txt'. Changes on the header file LP5562 configurable definitions are added. Pattern RGB data is fixed as constant value. (No side effect on other devices, LP5521 or LP5523.) (cooloney@gmail.com: remove redundant mutex_unlock(). Reported by Dan Carpenter <dan.carpenter@oracle.com>) Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: fix problem on removing LED attributesMilo(Woogyom) Kim
LP55XX common device attributes, 'led_current' and 'max_current' are created while loading the driver. Those are LED device attributes which are removed automatically on releasing led class devices - led_classdev_unregister(). Therefore, this duplicate code should be removed. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: add new function for removing device attribtuesMilo(Woogyom) Kim
lp55xx_unregister_sysfs() is used for removing lp55xx device attributes. Chip specific and engine attributes are removed on unloading the driver. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: support device specific attributesMilo(Woogyom) Kim
To support device specific attributes, new common driver function is added. Eventually those are created on registering the sysfs with common dev attrs. Furthermore, this patch makes adding device attributes simple in each driver. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: support firmware interfaceMilo(Woogyom) Kim
This patch provides additional device attributes which enable loading the firmware. ('select_engine' and 'run_engine') To run a LED pattern, two parts of driver should be enabled. Common features : lp55xx-common =============================== Firmware interface for loading LED patterns Chip specific features : leds-lp5521, leds-lp5523 ================================================= Register addresses for loading firmware data Register addresses for running selected engine Pattern programming sequence ============================ LP55xx chips have three program engines. To load and run a LED pattern, the programming sequence is as follows. (1) Select an engine number (1/2/3) (2) Set engine mode to load (3) Write pattern data into selected area (4) Set engine mode to run This sequence is almost same as the firmware interface. (1) Select an engine number : 'select_engine' dev attribute (2) Mode change to load : 'loading' of firmware class (3) Write pattern data into selected area : 'data' of firmware class (4) Mode change to run : 'run_engine' dev attribute (1) and (4) are device specific features which provide callback functions (2) and (3) are common features. For example, echo 1 or 2 or 3 > /sys/bus/i2c/devices/xxxx/select_engine echo 1 > /sys/class/firmware/lp5521/loading echo "4000600040FF6000" > /sys/class/firmware/lp5521/data echo 0 > /sys/class/firmware/lp5521/loading echo 1 > /sys/bus/i2c/devices/xxxx/run_engine As soon as 'loading' is set to 0, registered callback is called. Inside the callback, the selected engine is loaded and memory is updated. To run programmed pattern, 'run_engine' attribute should be enabled. Device specific data structure ============================== o Firmware callback load selected engine and update program memory o Run engine change the engine mode o 'engine_idx' and firmware data, 'fw' Those are used in the driver internally with callback functions Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: add new lp55xx_register_sysfs() for the firmware interfaceMilo(Woogyom) Kim
LP55xx family chips have internal program memory which run various patterns. Using this memory, LEDs continue on blinking/dimming without continuous I2C commands. That means the I2C HOST can be entered into sleep once the memory is updated. An application can get hex data from a file and write them into the program memory through the I2C. This is general firwmare interface. This patch is the initial step for adding the firmware interface. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: fix error condition in lp55xx_register_leds()Milo(Woogyom) Kim
Use lp55xx_unregister_leds() rather than duplicate code. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx_unregister_leds()Milo(Woogyom) Kim
To unregister led class devices and sysfs attributes, LP5521 and LP5523 have each driver function. This patch makes both drivers simple using common driver function, lp55xx_unregister_leds(). And some unused variables are removed. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: provide common LED current settingMilo(Woogyom) Kim
LED current is configurable via the sysfs. Max current is a read-only attribute. These attributes code can be shared in lp55xx common driver. Device attributes: 'led_current' and 'max_current' move to lp55xx common driver Replaced functions: show_max_current() => lp55xx_show_max_current() show_current() => lp55xx_show_current() store_current() => lp55xx_store_current() LED setting function: set_led_current() Current registers are device specific, so configurable function is added in each driver. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx_set_brightness()Milo(Woogyom) Kim
lp5521_set_brightness() and lp5523_set_brightness() are replaced with common function, lp55xx_set_brightness(). This function is invoked when the brightness of each LED channel is updated. LP5521 and LP5523 have different register address for the brightness control, so this work is done by chip specific brightness_work_fn(). lp5521/5523_led_brightness_work(): use lp55xx_led and lp55xx_chip data structure. use lp55xx write function. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx_init_led() common functionMilo(Woogyom) Kim
lp5521_init_led() and lp5523_init_led() are replaced with one common function, lp55xx_init_led(). Max channels is configurable, so it's used in lp55xx_init_led(). 'LP5523_LEDS' are changed to 'LP5523_MAX_LEDS'. lp55xx_set_brightness, lp55xx_led_attributes: skeleton Will be filled in next patches. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common led registration functionMilo(Woogyom) Kim
LED class devices are registered in lp5521_register_leds() and lp5523_register_leds(). Two separate functions are merged into consolidated lp55xx function, lp55xx_register_leds(). Error handling fix: Unregistering LEDS are handled in lp55xx_register_leds() when LED registration failure occurs. So each driver error handler is changed to 'err_register_leds' Chip dependency: 'brightness_work_fn' and 'set_led_current' To make the structure abstract, both functions are configured in each driver. Those functions should be done by each driver because register control is chip-dependant work. lp55xx_init_led: skeleton Will be filled in next patch Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common deinit functionMilo(Woogyom) Kim
Two separate de-init functions are merged into one common function. And it is used in err_post_init of lp55xx_init_device(). Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: clean up init functionMilo(Woogyom) Kim
lp5521/5523_init_device() are replaced with lp55xx common function, lp55xx_init_device(). Error handler in init_device: deinit function are matched with 'err_post_init' section in lp55xx_init_device(). Remove LP5523 engine intialization code: Engine functionality is not mandatory but optional. Moreover engine initialization is done internally with device reset command. Therefore, this code is unnecessary. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common init function - post intMilo(Woogyom) Kim
LP5521/5523 chip configuration is replaced with lp55xx common function, lp55xx_post_init_device(). Name change: lp5521/5523_configure() to lp5521/5523_post_init_device() These are called in init function. Register access function Argument type is changed from 'i2c_client' to 'lp55xx_chip'. Use exported R/W functions of lp55xx common driver. Temporary variables in lp5521/5523_init_device() These functions will be removed but temporary variables are needed for blocking build warnings - incompatible pointer. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common init function - detectMilo(Woogyom) Kim
LP5521/5523 chip detection functions are replaced with lp55xx common function, lp55xx_detect_device(). Chip dependent address and values are configurable in each driver. In init function, chip detection is executed. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common init function - resetMilo(Woogyom) Kim
LP5521/5523 reset device functions are moved to lp55xx common driver. Value of register address and value are chip dependent. Those are configured in each driver. In init function, reset command is executed. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: use lp55xx common init function - platform dataMilo(Woogyom) Kim
LP5521/5523 platform data functions are moved to lp55xx common driver. New init function, lp55xx_init_device() is created. Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>
2013-02-06leds-lp55xx: add new common driver for lp5521/5523Milo(Woogyom) Kim
This patch supports basic common driver code for LP5521, LP5523/55231 devices. ( Driver Structure Data ) lp55xx_led and lp55xx_chip In lp55xx common driver, two different data structure is used. o lp55xx_led control multi output LED channels such as led current, channel index. o lp55xx_chip general chip control such like the I2C and platform data. For example, LP5521 has maximum 3 LED channels. LP5523/55231 has 9 output channels. lp55xx_chip for LP5521 ... lp55xx_led #1 lp55xx_led #2 lp55xx_led #3 lp55xx_chip for LP5523 ... lp55xx_led #1 lp55xx_led #2 . . lp55xx_led #9 ( Platform Data ) LP5521 and LP5523/55231 have own specific platform data. However, this data can be handled with just one platform data structure. The lp55xx platform data is declared in the header. This structure is derived from leds-lp5521.h and leds-lp5523.h Signed-off-by: Milo(Woogyom) Kim <milo.kim@ti.com> Signed-off-by: Bryan Wu <cooloney@gmail.com>