| Age | Commit message (Collapse) | Author |
|---|
|
Commit 2b83ff96f51d ("led: core: Fix brightness setting when setting delay_off=0")
replaced del_timer_sync(&led_cdev->blink_timer) with led_stop_software_blink()
in led_blink_set(), which additionally clears LED_BLINK_SW flag as well as
zeroes blink_delay_on and blink_delay_off properties of the struct led_classdev.
Cleansing of the latter ones wasn't required to fix the original issue but
wasn't considered harmful. It nonetheless turned out to be so in case when
pointer to one or both props is passed to led_blink_set() like in the
ledtrig-timer.c. In such cases zeroes are passed later in delay_on and/or
delay_off arguments to led_blink_setup(), which results either in stopping
the software blinking or setting blinking frequency always to 1Hz.
Avoid using led_stop_software_blink() and add a single call required
to clear LED_BLINK_SW flag, which was the only needed modification to
fix the original issue.
Fixes 2b83ff96f51d ("led: core: Fix brightness setting when setting delay_off=0")
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
With the current code, the following sequence won't work :
echo timer > trigger
echo 0 > delay_off
* at this point we call
** led_delay_off_store
** led_blink_set
*** stop timer
** led_blink_setup
** led_set_software_blink
*** if !delay_on, led off
*** if !delay_off, set led_set_brightness_nosleep <--- LED_BLINK_SW is set but timer is stop
*** otherwise start timer/set LED_BLINK_SW flag
echo xxx > brightness
* led_set_brightness
** if LED_BLINK_SW
*** if brightness=0, led off
*** else apply brightness if next timer <--- timer is stop, and will never apply new setting
** otherwise set led_set_brightness_nosleep
To fix that, when we delete the timer, we should clear LED_BLINK_SW.
Cc: linux-leds@vger.kernel.org
Signed-off-by: Matthieu CASTET <matthieu.castet@parrot.com>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
In preparation for unconditionally passing the struct timer_list pointer to
all timer callbacks, switch to using the new timer_setup() and from_timer()
to pass the timer pointer explicitly.
Cc: Richard Purdie <rpurdie@rpsys.net>
Cc: Pavel Machek <pavel@ucw.cz>
Cc: Willy Tarreau <w@1wt.eu>
Cc: linux-leds@vger.kernel.org
Signed-off-by: Kees Cook <keescook@chromium.org>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>
|
|
All 3 of led_timer_func, led_set_brightness and led_set_software_blink
set blink_brightness. If led_timer_func or led_set_software_blink race
with led_set_brightness they may end up overwriting the new
blink_brightness. The new atomic work_flags does not protect against
this as it just protects the flags and not blink_brightness.
This commit introduces a new new_blink_brightness value which gets
set by led_set_brightness and read by led_timer_func on LED on, fixing
this.
Dealing with the new brightness at LED on time, makes the new
brightness apply sooner, which also fixes a led_set_brightness which
happens while a oneshot blink which ends in LED on is running not
getting applied.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
All the LED_BLINK* flags are accessed read-modify-write from e.g.
led_set_brightness and led_blink_set_oneshot while both
set_brightness_work and the blink_timer may be running.
If these race then the modify step done by one of them may be lost,
switch the LED_BLINK* flags to a new atomic work_flags bit-field
to avoid this race.
Signed-off-by: Hans de Goede <hdegoede@redhat.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Commit 76931edd54f8 ("leds: fix brightness changing when software blinking
is active") changed the semantics of led_set_brightness() which according
to the documentation should disable blinking upon any brightness setting.
Moreover it made it different for soft blink case, where it was possible
to change blink brightness, and for hardware blink case, where setting
any brightness greater than 0 was ignored.
While the change itself is against the documentation claims, it was driven
also by the fact that timer trigger remained active after turning blinking
off. Fixing that would have required major refactoring in the led-core,
led-class, and led-triggers because of cyclic dependencies.
Finally, it has been decided that allowing for brightness change during
blinking is beneficial as it can be accomplished without disturbing
blink rhythm.
The change in brightness setting semantics will not affect existing
LED class drivers that implement blink_set op thanks to the LED_BLINK_SW
flag introduced by this patch. The flag state will be from now on checked
in led_set_brightness() which will allow to distinguish between software
and hardware blink mode. In the latter case the control will be passed
directly to the drivers which apply their semantics on brightness set,
which is disable the blinking in case of most such drivers. New drivers
will apply new semantics and just change the brightness while hardware
blinking is on, if possible.
The issue was smuggled by subsequent LED core improvements, which modified
the code that originally introduced the problem.
Fixes: f1e80c07416a ("leds: core: Add two new LED_BLINK_ flags")
Signed-off-by: Tony Makkiel <tony.makkiel@daqri.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
Add helpers for calling brightness_set(_blocking) allowing to
simplify the code and make it better readable.
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
When a USB LED device is unplugged the remove call chain calls
led_classdev_unregister which tries to switch the LED off.
As the device has been removed already this results in a ENODEV
error message in dmesg.
Avoid this error message by ignoring ENODEV in calls from
led_classdev_unregister if the LED device is flagged as pluggable.
Therefore a new flag LED_HW_PLUGGABLE was introduced which should be set by
all LED drivers handling pluggable LED devices (mainly USB LED devices).
Signed-off-by: Heiner Kallweit <hkallweit1@gmail.com>
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
|
|
This patch removes SET_BRIGHTNESS_ASYNC and SET_BRIGHTNESS_SYNC flags.
led_set_brightness() now calls led_set_brightness_nosleep() instead of
choosing between sync and async op basing on the flags defined by the
driver.
From now on, if a user wants to make sure that brightness will be set
synchronously, they have to use led_set_brightness_sync() API. It is now
being made publicly available since it has become apparent that it is
a caller who should decide whether brightness is to be set in
a synchronous or an asynchronous way.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This patch makes LED core capable of setting brightness for drivers
that implement brightness_set_blocking op. It removes from LED class
drivers responsibility for using work queues on their own.
In order to achieve this set_brightness_delayed callback is being
modified to directly call one of available ops for brightness setting.
led_set_brightness_async() function didn't set brightness in an
asynchronous way in all cases. It was mistakenly assuming that all
LED subsystem drivers used work queue in their brightness_set op,
whereas only half of them did that. Since it has no users now,
it is being removed.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This patch adds led_set_brightness_nosleep() and led_set_brightness_nopm()
functions, that guarantee setting LED brightness in a non-blocking way.
The latter is used from pm_ops context and doesn't modify the brightness
cached in the struct led_classdev. Its execution always ends up with
a call to brightness setting op - either directly or through
a set_brightness_work, regardless of LED_SUSPENDED flag state.
The patch also replaces led_set_brightness_async() with
led_set_brightness_nosleep() in all places where the most vital was setting
brightness in a non sleeping way but not necessarily asynchronously, which
is not needed for non-blocking drivers.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
This patch adds LED_BLINK_BRIGHTNESS_CHANGE flag to indicate that blink
brightness has changed, and LED_BLINK_DISABLE flag to indicate that
blinking deactivation has been requested. In order to use the flags
led_timer_function and set_brightness_delayed callbacks as well as
led_set_brightness() function are being modified. The main goal of these
modifications is to prepare set_brightness_work for extension of the
scope of its responsibilities.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
|
|
LED core has a mixture of EXPORT_SYMBOL and EXPORT_SYMBOL_GPL macros.
This patch fixes this discrepancy and switches to using EXPORT_SYMBOL_GPL
for each exported function.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Pavel Machek <pavel@ucw.cz>
|
|
Since the API for controlling LED brightness and blinking is defined in
the LED core, move the related timer and work callbacks to the led-core.c,
and initialize them through a new led_core_init API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Andrew Lunn <andrew@lunn.ch>
Acked-by: Pavel Machek <pavel@ucw.cz>
|
|
The following sequence:
echo timer >/sys/class/leds/<name>/trigger
echo 1 >/sys/class/leds/<name>/brightness
should change the ON brightness for blinking.
The function led_set_brightness() was mistakenly initiating the
delayed blink stop procedure, which resulted in no blinking with
the timer trigger still active.
This patch fixes the problem by changing led_set_brightness()
to not initiate the delayed blink stop when brightness is not 0.
CC: Richard Purdie <rpurdie@rpsys.net>
CC: Kyungmin Park <kyungmin.park@samsung.com>
CC: linux-leds@vger.kernel.org
CC: linux-kernel@vger.kernel.org
Acked-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Signed-off-by: Stas Sergeev <stsp@users.sourceforge.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
There are use cases when setting a LED brightness has to
have immediate effect (e.g. setting a torch LED brightness).
This patch extends LED subsystem to support such operations.
The LED subsystem internal API __led_set_brightness is changed
to led_set_brightness_async and new led_set_brightness_sync API
is added.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Add a mechanism for locking LED subsystem sysfs interface.
This patch prepares ground for addition of LED Flash Class
extension, whose API will be integrated with V4L2 Flash API.
Such a fusion enforces introducing a locking scheme, which
will secure consistent access to the LED Flash Class device.
The mechanism being introduced allows for disabling LED
subsystem sysfs interface by calling led_sysfs_disable function
and enabling it by calling led_sysfs_enable. The functions
alter the LED_SYSFS_DISABLE flag state and must be called
under mutex lock. The state of the lock is checked with use
of led_sysfs_is_disabled function. Such a design allows for
providing immediate feedback to the user space on whether
the LED Flash Class device is available or is under V4L2 Flash
sub-device control.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
led_update_brightness helper function used to be exploited only locally
in the led-class.c module, where its result was being passed to the
brightness_show sysfs callback. With the introduction of v4l2-flash
subdevice the same functionality becomes required for reading current
brightness from a LED device. This patch adds checking of return value
of the brightness_get callback and moves the led_update_brightness()
function to the LED subsystem public API.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Reorder include directives so that they are arranged
in alphabetical order.
Signed-off-by: Jacek Anaszewski <j.anaszewski@samsung.com>
Acked-by: Kyungmin Park <kyungmin.park@samsung.com>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This reverts commit 8b37e1bef5a6b60e949e28a4db3006e4b00bd758.
It's broken as it changes led_blink_set() in a way that it can now sleep
(while synchronously waiting for workqueue to be cancelled). That's a
problem, because it's possible that this function gets called from atomic
context (tpt_trig_timer() takes a readlock and thus disables preemption).
This has been brought up 3 weeks ago already [1] but no proper fix has
materialized, and I keep seeing the problem since 3.17-rc1.
[1] https://lkml.org/lkml/2014/8/16/128
BUG: sleeping function called from invalid context at kernel/workqueue.c:2650
in_atomic(): 1, irqs_disabled(): 0, pid: 2335, name: wpa_supplicant
5 locks held by wpa_supplicant/2335:
#0: (rtnl_mutex){+.+.+.}, at: [<ffffffff814c7c92>] rtnl_lock+0x12/0x20
#1: (&wdev->mtx){+.+.+.}, at: [<ffffffffc06e649c>] cfg80211_mgd_wext_siwessid+0x5c/0x180 [cfg80211]
#2: (&local->mtx){+.+.+.}, at: [<ffffffffc0817dea>] ieee80211_prep_connection+0x17a/0x9a0 [mac80211]
#3: (&local->chanctx_mtx){+.+.+.}, at: [<ffffffffc08081ed>] ieee80211_vif_use_channel+0x5d/0x2a0 [mac80211]
#4: (&trig->leddev_list_lock){.+.+..}, at: [<ffffffffc081e68c>] tpt_trig_timer+0xec/0x170 [mac80211]
CPU: 0 PID: 2335 Comm: wpa_supplicant Not tainted 3.17.0-rc3 #1
Hardware name: LENOVO 7470BN2/7470BN2, BIOS 6DET38WW (2.02 ) 12/19/2008
ffff8800360b5a50 ffff8800751f76d8 ffffffff8159e97f ffff8800360b5a30
ffff8800751f76e8 ffffffff810739a5 ffff8800751f77b0 ffffffff8106862f
ffffffff810685d0 0aa2209200000000 ffff880000000004 ffff8800361c59d0
Call Trace:
[<ffffffff8159e97f>] dump_stack+0x4d/0x66
[<ffffffff810739a5>] __might_sleep+0xe5/0x120
[<ffffffff8106862f>] flush_work+0x5f/0x270
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffff810945ca>] ? mark_held_locks+0x6a/0x90
[<ffffffff81068a5f>] ? __cancel_work_timer+0x6f/0x100
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffffc081ecdd>] ieee80211_mod_tpt_led_trig+0x9d/0x160 [mac80211]
[<ffffffffc07e4278>] __ieee80211_recalc_idle+0x98/0x140 [mac80211]
[<ffffffffc07e59ce>] ieee80211_idle_off+0xe/0x10 [mac80211]
[<ffffffffc0804e5b>] ieee80211_add_chanctx+0x3b/0x220 [mac80211]
[<ffffffffc08062e4>] ieee80211_new_chanctx+0x44/0xf0 [mac80211]
[<ffffffffc080838a>] ieee80211_vif_use_channel+0x1fa/0x2a0 [mac80211]
[<ffffffffc0817df8>] ieee80211_prep_connection+0x188/0x9a0 [mac80211]
[<ffffffffc081c246>] ieee80211_mgd_auth+0x256/0x2e0 [mac80211]
[<ffffffffc07eab33>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffc06cb006>] cfg80211_mlme_auth+0x106/0x270 [cfg80211]
[<ffffffffc06ce085>] cfg80211_conn_do_work+0x155/0x3b0 [cfg80211]
[<ffffffffc06cf670>] cfg80211_connect+0x3f0/0x540 [cfg80211]
[<ffffffffc06e6148>] cfg80211_mgd_wext_connect+0x158/0x1f0 [cfg80211]
[<ffffffffc06e651e>] cfg80211_mgd_wext_siwessid+0xde/0x180 [cfg80211]
[<ffffffffc06e36c0>] ? cfg80211_wext_giwessid+0x50/0x50 [cfg80211]
[<ffffffffc06e36dd>] cfg80211_wext_siwessid+0x1d/0x40 [cfg80211]
[<ffffffff81584d0c>] ioctl_standard_iw_point+0x14c/0x3e0
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff8158502a>] ioctl_standard_call+0x8a/0xd0
[<ffffffff81584fa0>] ? ioctl_standard_iw_point+0x3e0/0x3e0
[<ffffffff81584b76>] wireless_process_ioctl.constprop.10+0xb6/0x100
[<ffffffff8158521d>] wext_handle_ioctl+0x5d/0xb0
[<ffffffff814cfb29>] dev_ioctl+0x329/0x620
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff8149c7f2>] sock_ioctl+0x142/0x2e0
[<ffffffff811b0140>] do_vfs_ioctl+0x300/0x520
[<ffffffff815a67fb>] ? sysret_check+0x1b/0x56
[<ffffffff810946ed>] ? trace_hardirqs_on_caller+0xfd/0x1c0
[<ffffffff811b03e1>] SyS_ioctl+0x81/0xa0
[<ffffffff815a67d6>] system_call_fastpath+0x1a/0x1f
wlan0: send auth to 00:0b:6b:3c:8c:e4 (try 1/3)
wlan0: authenticated
wlan0: associate with 00:0b:6b:3c:8c:e4 (try 1/3)
wlan0: RX AssocResp from 00:0b:6b:3c:8c:e4 (capab=0x431 status=0 aid=2)
wlan0: associated
IPv6: ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
cfg80211: Calling CRDA for country: NA
wlan0: Limiting TX power to 27 (27 - 0) dBm as advertised by 00:0b:6b:3c:8c:e4
=================================
[ INFO: inconsistent lock state ]
3.17.0-rc3 #1 Not tainted
---------------------------------
inconsistent {SOFTIRQ-ON-W} -> {IN-SOFTIRQ-W} usage.
swapper/0/0 [HC0[0]:SC1[1]:HE1:SE0] takes:
((&(&led_cdev->blink_work)->work)){+.?...}, at: [<ffffffff810685d0>] flush_work+0x0/0x270
{SOFTIRQ-ON-W} state was registered at:
[<ffffffff81094dbe>] __lock_acquire+0x30e/0x1a30
[<ffffffff81096c81>] lock_acquire+0x91/0x110
[<ffffffff81068608>] flush_work+0x38/0x270
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffffc081ecdd>] ieee80211_mod_tpt_led_trig+0x9d/0x160 [mac80211]
[<ffffffffc07e4278>] __ieee80211_recalc_idle+0x98/0x140 [mac80211]
[<ffffffffc07e59ce>] ieee80211_idle_off+0xe/0x10 [mac80211]
[<ffffffffc0804e5b>] ieee80211_add_chanctx+0x3b/0x220 [mac80211]
[<ffffffffc08062e4>] ieee80211_new_chanctx+0x44/0xf0 [mac80211]
[<ffffffffc080838a>] ieee80211_vif_use_channel+0x1fa/0x2a0 [mac80211]
[<ffffffffc0817df8>] ieee80211_prep_connection+0x188/0x9a0 [mac80211]
[<ffffffffc081c246>] ieee80211_mgd_auth+0x256/0x2e0 [mac80211]
[<ffffffffc07eab33>] ieee80211_auth+0x13/0x20 [mac80211]
[<ffffffffc06cb006>] cfg80211_mlme_auth+0x106/0x270 [cfg80211]
[<ffffffffc06ce085>] cfg80211_conn_do_work+0x155/0x3b0 [cfg80211]
[<ffffffffc06cf670>] cfg80211_connect+0x3f0/0x540 [cfg80211]
[<ffffffffc06e6148>] cfg80211_mgd_wext_connect+0x158/0x1f0 [cfg80211]
[<ffffffffc06e651e>] cfg80211_mgd_wext_siwessid+0xde/0x180 [cfg80211]
[<ffffffffc06e36dd>] cfg80211_wext_siwessid+0x1d/0x40 [cfg80211]
[<ffffffff81584d0c>] ioctl_standard_iw_point+0x14c/0x3e0
[<ffffffff8158502a>] ioctl_standard_call+0x8a/0xd0
[<ffffffff81584b76>] wireless_process_ioctl.constprop.10+0xb6/0x100
[<ffffffff8158521d>] wext_handle_ioctl+0x5d/0xb0
[<ffffffff814cfb29>] dev_ioctl+0x329/0x620
[<ffffffff8149c7f2>] sock_ioctl+0x142/0x2e0
[<ffffffff811b0140>] do_vfs_ioctl+0x300/0x520
[<ffffffff811b03e1>] SyS_ioctl+0x81/0xa0
[<ffffffff815a67d6>] system_call_fastpath+0x1a/0x1f
irq event stamp: 493416
hardirqs last enabled at (493416): [<ffffffff81068a5f>] __cancel_work_timer+0x6f/0x100
hardirqs last disabled at (493415): [<ffffffff81067e9f>] try_to_grab_pending+0x1f/0x160
softirqs last enabled at (493408): [<ffffffff81053ced>] _local_bh_enable+0x1d/0x50
softirqs last disabled at (493409): [<ffffffff81054c75>] irq_exit+0xa5/0xb0
other info that might help us debug this:
Possible unsafe locking scenario:
CPU0
----
lock((&(&led_cdev->blink_work)->work));
<Interrupt>
lock((&(&led_cdev->blink_work)->work));
*** DEADLOCK ***
2 locks held by swapper/0/0:
#0: (((&tpt_trig->timer))){+.-...}, at: [<ffffffff810b4c50>] call_timer_fn+0x0/0x180
#1: (&trig->leddev_list_lock){.+.?..}, at: [<ffffffffc081e68c>] tpt_trig_timer+0xec/0x170 [mac80211]
stack backtrace:
CPU: 0 PID: 0 Comm: swapper/0 Not tainted 3.17.0-rc3 #1
Hardware name: LENOVO 7470BN2/7470BN2, BIOS 6DET38WW (2.02 ) 12/19/2008
ffffffff8246eb30 ffff88007c203b00 ffffffff8159e97f ffffffff81a194c0
ffff88007c203b50 ffffffff81599c29 0000000000000001 ffffffff00000001
ffff880000000000 0000000000000006 ffffffff81a194c0 ffffffff81093ad0
Call Trace:
<IRQ> [<ffffffff8159e97f>] dump_stack+0x4d/0x66
[<ffffffff81599c29>] print_usage_bug+0x1f4/0x205
[<ffffffff81093ad0>] ? check_usage_backwards+0x140/0x140
[<ffffffff810944d3>] mark_lock+0x223/0x2b0
[<ffffffff81094d60>] __lock_acquire+0x2b0/0x1a30
[<ffffffff81096c81>] lock_acquire+0x91/0x110
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff81068608>] flush_work+0x38/0x270
[<ffffffff810685d0>] ? mod_delayed_work_on+0x80/0x80
[<ffffffff810945ca>] ? mark_held_locks+0x6a/0x90
[<ffffffff81068a5f>] ? __cancel_work_timer+0x6f/0x100
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff8109469d>] ? trace_hardirqs_on_caller+0xad/0x1c0
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff81068a6b>] __cancel_work_timer+0x7b/0x100
[<ffffffff81068b0e>] cancel_delayed_work_sync+0xe/0x10
[<ffffffff8147cf3b>] led_blink_set+0x1b/0x40
[<ffffffffc081e6b0>] tpt_trig_timer+0x110/0x170 [mac80211]
[<ffffffff810b4cc5>] call_timer_fn+0x75/0x180
[<ffffffff810b4c50>] ? process_timeout+0x10/0x10
[<ffffffffc081e5a0>] ? __ieee80211_get_rx_led_name+0x10/0x10 [mac80211]
[<ffffffff810b50ac>] run_timer_softirq+0x1fc/0x2f0
[<ffffffff81054805>] __do_softirq+0x115/0x2e0
[<ffffffff81054c75>] irq_exit+0xa5/0xb0
[<ffffffff810049b3>] do_IRQ+0x53/0xf0
[<ffffffff815a74af>] common_interrupt+0x6f/0x6f
<EOI> [<ffffffff8147b56e>] ? cpuidle_enter_state+0x6e/0x180
[<ffffffff8147b732>] cpuidle_enter+0x12/0x20
[<ffffffff8108bba0>] cpu_startup_entry+0x330/0x360
[<ffffffff8158fb51>] rest_init+0xc1/0xd0
[<ffffffff8158fa90>] ? csum_partial_copy_generic+0x170/0x170
[<ffffffff81af3ff2>] start_kernel+0x44f/0x45a
[<ffffffff81af399c>] ? set_init_arg+0x53/0x53
[<ffffffff81af35ad>] x86_64_start_reservations+0x2a/0x2c
[<ffffffff81af36a0>] x86_64_start_kernel+0xf1/0xf4
Cc: Vincent Donnefort <vdonnefort@gmail.com>
Cc: Hugh Dickins <hughd@google.com>
Cc: Tejun Heo <tj@kernel.org>
Signed-off-by: Jiri Kosina <jkosina@suse.cz>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
This patch converts the blink timer from led-core to workqueue which is more
suitable for this kind of non-priority operations. Moreover, timer may lead to
errors when a LED setting function use a scheduling function such as pinctrl
which is using mutex.
Signed-off-by: Vincent Donnefort <vdonnefort@gmail.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
When using the timer trigger and setting delay_on to 0, the led
will stay in whatever state is was in, while intuitively one
would expect it to turn off. This patch changes the behaviour to
turn it off.
Signed-off-by: Stefan Sørensen <stefan.sorensen@spectralink.com>
Signed-off-by: Bryan Wu <cooloney@gmail.com>
|
|
Delay execution of led_set_brightness() if need to stop soft-blink
timer.
This allows led_set_brightness to be called in hard-irq context even if
soft-blink was activated on that LED.
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Cc: Pawel Moll <pawel.moll@arm.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
drivers/leds/led-core.c:56:6: sparse: symbol 'led_blink_setup' was not declared. Should it be static?
drivers/leds/led-triggers.c:233:6: sparse: symbol 'led_trigger_blink_setup' was not declared. Should it be static?
Reported-by: Fengguang Wu <wfg@linux.intel.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Rename leds external interface led_brightness_set() to led_set_brightness().
This is the second phase of the change to reduce confusion between the
leds internal and external interfaces that set brightness. With this change,
now the external interface is led_set_brightness(). The first phase renamed
the internal interface led_set_brightness() to __led_set_brightness().
There are no changes to the interface implementations.
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Rename leds internal interface led_set_brightness() to __led_set_brightness()
to reduce confusion between led_set_brightness() and the external interface
led_brightness_set(). led_brightness_set() cancels the timer and then calls
led_set_brightness().
Signed-off-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Move led_stop_software_blink() code into led_brightness_set() to ensure
software blink timer is stopped and cleared when changing trigger.
Also use led_set_brightness() instead of calling
led_cdev->brightness_set() directly to keep led_cdev->brightness
consistent with current LED status.
This ensure proper cleaning when changing triggers, as without this fix
a LED may be turned off while leaving it's led_cdev->brightness = 1,
leading to an erratic software-blink behaviour.
The problem was easy to reproduce by changing the trigger from "timer"
to "oneshot".
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
Add two new functions, led_blink_set_oneshot and
led_trigger_blink_oneshot, to be used by triggers for one-shot blink of
led devices.
This is implemented extending the existing software-blink code, and uses
the same timer and handler function.
The behavior of the code is to do a blink-on, blink-off sequence when
the function is called, ignoring other calls until the sequence is
completed so that the leds keep blinking at constant rate if the
functions are called repeatedly.
This is meant to be used by drivers which needs to trigger on sporadic
event, but doesn't have clear busy/idle trigger points.
After the blink sequence the led remains off. This behavior can be
inverted setting the "invert" argument, which blink the led off, than on
and leave the led on after the sequence.
(bryan.wu@canonical.com: rebase to commit 'leds: don't disable blinking
when writing the same value to delay_on or delay_off')
Signed-off-by: Fabio Baltieri <fabio.baltieri@gmail.com>
Acked-by: Shuah Khan <shuahkhan@gmail.com>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
delay_off
Function led_set_software_blink() assumes that blink timer is still running,
but commit 488bc35bf40df89d37486c1826b178a2fba36ce7 introduced disabling
of blink timer before each call to led_set_software_blink().
Correct led_software_blink():
1) remove protection against reprogramming blink timer to the same values,
because it only disables blinking now,
2) remove unnecessary call to led_stop_software_blink().
Signed-off-by: Rafal Prylowski <prylowski@metasoft.pl>
Cc: Richard Purdie <rpurdie@rpsys.net>
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
|
|
After moving some core functions to led-core.c, led-class.c can be built
as module again.
Signed-off-by: Bryan Wu <bryan.wu@canonical.com>
Acked-by: Richard Purdie <richard.purdie@linuxfoundation.org>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Andrew Morton <akpm@linux-foundation.org>
Signed-off-by: Linus Torvalds <torvalds@linux-foundation.org>
|
|
Break the lines which were more than 80 characters into more
lines; replace SPACEs with TABs; correct ident at switch-case;
change character encoding from ISO-8859-2 to UTF-8.
The order of the functions in led-triggers.c changed in order
the similar functions can still be together under titles
"Used by LED Class", "LED Trigger Interface" and "Simple
LED Tigger Interface" as was grouped before when exported
with EXPORT_SYMBOL.
Signed-off-by: Márton Németh <nm127@freemail.hu>
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
|
Covert leds_list_lock to a rw_sempahore to match previous LED trigger
locking fixes, fixing lock ordering.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
|
|
locking init cleanups:
- convert " = SPIN_LOCK_UNLOCKED" to spin_lock_init() or DEFINE_SPINLOCK()
- convert rwlocks in a similar manner
this patch was generated automatically.
Motivation:
- cleanliness
- lockdep needs control of lock initialization, which the open-coded
variants do not give
- it's also useful for -rt and for lock debugging in general
Signed-off-by: Ingo Molnar <mingo@elte.hu>
Signed-off-by: Arjan van de Ven <arjan@linux.intel.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
|
Add the foundations of a new LEDs subsystem. This patch adds a class which
presents LED devices within sysfs and allows their brightness to be
controlled.
Signed-off-by: Richard Purdie <rpurdie@rpsys.net>
Cc: Russell King <rmk@arm.linux.org.uk>
Cc: Greg KH <greg@kroah.com>
Signed-off-by: Andrew Morton <akpm@osdl.org>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>
|
